Precautions
Please keep your headphones clean at all times especially
inside the rubber earbud (see fig. ).
If any dust or ear wax inside the earbud, you may
experience some listening difficulties.
Listening with headphones at high volume may affect
your hearing. For traffic safety, do not use while driving
or cycling.
The earbuds may deteriorate due to long-term storage or
use.
Install the earbuds firmly onto the headphones. If an
earbud accidentally detaches and is left in your ear, it may
cause injury.
It may be advisable to remove earrings or pierced
accessories before using the headphones.
Do not bend the ear-clip excessively. If it is bent 90
degrees or more, it may break.
Note on static electricity
In particularly dry air conditions, mild tingling may be felt
on your ears. This is a result of static electricity accumulated
in the body, and not a malfunction of the headphones.
The effect can be minimized by wearing clothes made from
natural materials.
Optional replacement earbuds in other colours can be
ordered from your nearest Sony dealer.
English
Stereo headphones
Features
Ear-clip design for secure fit.
Neodymium magnets deliver clear and powerful sound.
Hybrid silicone rubber earbuds for comfort and secure fit.
Cord slider to prevent tangled cords.
How to use
Wearing the headphones (see fig. )
1
Wear the earbud marked in your right ear and
the one marked in your left ear (see fig. -).
2
Hook the headphones around your ears
(see fig. -).
There is a tactile dot on the unit marked to
distinguish the left side.
3
Clip around your ear lobes by rotating the
headphones (see fig. -).
4
Adjust the earbuds to comfortably fit your ears.
Move the clip as shown in the figure (-) for a
comfortable fit.
How to use the cord slider (see fig. -)
Move up and down to change the split position of the cord.
After you use the headphones, keep them with the cord
slider high positioned to avoid entangling the cord.
How to install the earbuds correctly
(see fig. )
If the earbuds do not fit your ears correctly, low-bass sound
may not be heard. To enjoy better sound quality, change the
earbuds to another size, or adjust the earbuds position to sit
on your ears comfortably and fit your ears snugly.
If the earbuds do not fit your ears, try another size. Confirm
the size of the earbuds by checking color inside
(see fig.
-).
When you change the earbuds, turn to install them firmly
on the headphones to prevent the earbud from detaching
and remaining in your ear.
Earbud sizes (inside color)
Small
Large
S
(Orange)
M
(Green)
L
(Light blue)
To detach an earbud (see fig. -)
While holding the headphone, twist and pull the earbud off.
Tip
If the earbud slips and cannot be detached, wrap it in a dry soft cloth.
To attach an earbud (see fig. -)
Push the parts inside of the earbud into the headphone until
the projecting part of the headphone is fully covered.
Cleaning the earbuds
Remove the earbuds from the headphones, and wash them
with a mild detergent solution.
Specifications
Type: Closed, dynamic
Driver unit: 9 mm (CCAW adopted),
dome type
Power handling capacity: 100 mW (IEC*)
Impedance: 16 Ω at 1 kHz
Sensitivity: 102 dB/mW
Frequency response: 6 – 23,000 Hz
Cord: 1.2 m (47
1
/4 in), Litz cord
Y-type
Plug: Gold-plated L-shaped
stereo mini plug
Mass: Approx. 8 g (0.28 oz)
without cord
Supplied accessories
Earbuds (S (2), M (2), L (2)), Operating Instructions (1)
* IEC = International Electrotechnical Commission
Design and specifications are subject to change without
notice.
Cord slider
Tactile dot
Colored parts
Sectional View