Philips PQ215/16 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル
ENGLISH
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
offers, register your product at www.philips.com/
welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving heads
3 Shaving unit
4 Retaining frame
5 Central spring of retaining frame
6 Hair chamber
7 On/off slide
8 Front panel
9 Charging light
10 Socket for small plug
11 Cleaning brush
12 Philips Cleaning Spray (HQ110)
(Optional)
13 Small plug
14 Mains cord with plug
15 Cutter
16 Guard
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
- Keep the appliance and the mains
cord dry.
- This symbol means: Forbidden to clean under a
running tap (Fig. 2).
Warning
- This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
- Children should be supervised to ensure that they
do not play with the appliance.
- Do not use the shaver or the mains cord if it is
damaged.
- If the mains cord is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
Caution
- Use, charge and store the appliance at a temperature
between 5°C and 35°C.
- Only use the mains cord supplied to charge the
appliance.
- Only use the cleaning brush supplied.
- Make sure the cleaning brush remains clean.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this user
manual, the appliance is safe to use based on scientic
evidence available today.
Charging
Make sure the shaver is switched off when you start to
charge it.
When you charge the shaver for the rst time or after
a long period of disuse, let it charge continuously for 12
hours. Charging normally takes approx. 8 hours. Charge
the appliance when the motor stops or starts running
slower.
Do not leave the appliance connected to the mains for
more than 24 hours.
1 Put the small plug in the shaver (Fig. 3).
2 Put the plug in the wall socket.
, The charging light goes on to indicate that the
appliance is charging (Fig. 4).
3 Remove the plug from the wall socket and pull the
small plug out of the shaver when the battery is
fully charged (Fig. 5).
Note: The shaver does not run from the mains. When the
battery is empty, you have to recharge the battery before
you can use the shaver again.
Cordless shaving time
A fully charged shaver has a cordless shaving time of
approximately 30 minutes.
Using the appliance
The shaver cannot be used directly from the mains.
1 Remove the protection cap.
2 Push the on/off slide upwards to switch on the
shaver (Fig. 6).
3 Move the shaving heads over your skin. Make both
straight and circular movements (Fig. 7).
Note: Shave on a dry face only. Do not use the shaver in
combination with gel, foam or water.
Note: Your skin may need 2 or 3 weeks to get accustomed
to the Philips shaving system.
4 Push the on/off slide downwards to switch off the
shaver.
5 Clean the shaver after every shave (see chapter
‘Cleaning and maintenance’).
PQ215
Register your product and get support at
www.philips.com/welcome
4222.002.5272.1
3
6 9
12
4
7
10 13
2 5
8
11
15
18 21
24
16
19
22 25
14 17
20
23
26
1
6 Put the protection cap on the shaver to prevent
damage and to avoid dirt accumulation in the
shaving heads (Fig. 8).
Cleaning and maintenance
Never use scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the
appliance.
Clean the shaver after every shave to guarantee better
shaving performance. For the best cleaning result, we
advise you to use Philips Cleaning Spray (HQ110). Ask
your Philips dealer for information.
Note: Philips Shaving Head Cleaning Spray (HQ110) may
not be available in all countries. Contact the Customer
Care Centre in your country about the availability of this
accessory.
After every shave: shaving unit and hair
chamber
1 Switch off the shaver, remove the plug from the
wall socket and pull the small plug out of the
shaver.
2 Clean the top of the appliance with the cleaning
brush supplied (Fig. 9).
3 Pull the shaving unit straight up off the
shaver (Fig. 10).
4 Clean the inside of the shaving unit with the
cleaning brush (Fig. 11).
5 Clean the hair chamber with the cleaning
brush (Fig. 12).
6 Put the shaving unit back onto the shaver (Fig. 13).
Every two months: shaving heads
Note: Do not use cleaning agents or alcohol to clean the
shaving heads. Only use Philips Cleaning Spray (HQ110).
1 Switch off the shaver, remove the plug from the
wall socket and pull the small plug out of the
shaver.
2 Pull the shaving unit straight up off the
shaver (Fig. 10).
3 To remove the retaining frame, push the sides of
the central spring towards each other (1).Then lift
the retaining frame out of the shaving unit (2)
(Fig. 14).
4 Slide the shaving heads out of the retaining frame.
Remove and clean one shaving head at a time. Each
shaving head consists of a cutter
and a guard (Fig. 15).
Note: Do not clean more than one cutter and guard at a
time, since they are all matching sets. If you accidentally mix
up the cutters and guards, it may take several weeks before
optimal shaving performance is restored.
5 Remove the guard from the cutter (Fig. 16).
6 Clean the cutter with the short-bristled side of the
cleaning brush. Brush carefully in the direction of
the arrows (Fig. 17).
7 Clean the guard with the long-bristled side of the
cleaning brush (Fig. 18).
8 Put the cutter back into the guard after
cleaning (Fig. 19).
9 Slide the shaving heads back into the retaining
frame (Fig. 20).
10 Put the retaining frame back into the shaving unit
(‘click’) (Fig. 21).
11 Put the shaving unit back onto the shaver (Fig. 13).
Storage
Keep the appliance dry.
Use and store the appliance at a temperature between
5°C and 35°C.
1 Switch off the shaver.
2 Put the protection cap on the shaver after use to
prevent damage and to avoid dirt accumulation in
the shaving heads (Fig. 8).
Replacement
Replace the shaving heads every two years for optimal
shaving results.
Replace damaged or worn shaving heads with Philips
shaving heads only (HQ4+ for China or HQ56 for the
rest of the world).
For instructions on how to remove the shaving heads,
see chapter ‘Cleaning and maintenance’, section ‘Every
two months: shaving heads’.
Accessories
To retain the top performance of your shaver, make sure
you clean it regularly and replace its shaving heads at the
recommended time.
Shaving heads
- We advise you to replace your shaving heads every
two years. Always replace them with Philips shaving
heads only (HQ4+ for China or HQ56 for the rest
of the world) (Fig. 22).
Cleaning
- Use Philips Cleaning Spray (HQ110) to clean the
shaving heads thoroughly.
Environment
- Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an ofcial collection point for recycling. By doing
this, you help to preserve the environment (Fig. 23).
- The built-in rechargeable battery contains substances
that may pollute the environment. Always remove
the battery before you discard and hand in the
shaver at an ofcial collection point. Dispose of the
battery at an ofcial collection point for batteries.
If you have trouble removing the battery, you can
also take the shaver to a Philips service centre. The
staff of this centre will remove the battery for you
and will dispose of it in an environmentally safe
way (Fig. 24).
Removing the rechargeable
battery
Only remove the rechargeable battery
if it is completely empty.
1 Remove the plug from the wall socket and pull the
small plug out of the shaver.
2 Let the shaver run until it stops, undo the screw on
the back of the shaver (1) and lift the back panel off
the shaver (2) (Fig. 25).
3 Remove the rechargeable battery (Fig. 26)
Do not connect the shaver to the mains again after you
have removed the battery.
Guarantee and service
If you need service or information or if you have a
problem, please visit the Philips website at www.philips.
com or contact the Philips Consumer Care Centre in
your country. You nd its phone number in the worldwide
guarantee leaet. If there is no Consumer Care Centre in
your country, go to your local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and guards) are not covered
by the terms of the international guarantee because they
are subject to wear.
Troubleshooting
This chapter summarises the most common problems
you could encounter with the appliance. If you are unable
to solve the problem with the information below, contact
the Consumer Care Centre in your country.
Problem Possible cause Solution
The shaver
does not
shave as
well as it
used to.
The shaving
heads are dirty.
You have not
cleaned the
shaver well
enough or
you have not
cleaned it for a
long time.
Clean the shaver
thoroughly before
you continue shaving.
See chapter ‘Cleaning
and maintenance’.
Long hairs
obstruct the
shaving heads.
Clean the cutters
and guards with
the cleaning brush
supplied. See chapter
‘Cleaning and
maintenance’, section
‘Every two months:
shaving heads’.
The shaving
heads are
damaged or
worn.
Replace the shaving
heads. See chapter
‘Replacement’.
The shaver
does not
work when
I push the
on/off slide
upwards.
The battery is
empty.
Recharge the
battery. See chapter
‘Charging’.
My skin is
irritated
after
shaving.
Your skin needs
time to get
used to the
Philips shaving
system.
Skin irritation during
the rst 2-3 weeks
of use is possible.
After this period, the
skin irritation usually
disappears.
The
rotation
speed of
the shaving
heads is
slower than
usual.
Too much dirt
has collected
in the shaving
heads.
Clean the shaving
heads. See chapter
‘Cleaning and
maintenance’.
The battery is
empty
Recharge the
battery. See chapter
‘Charging’.
每次剃须后:清洗剃须刀头部件和胡茬储藏室
1 关闭剃须刀电源,从电源插座中拔下电源插
头,并从剃须刀上拔出小插头。
2 用随附的清洁刷清洁产品顶部。
(图9)
3 垂直向上拉动剃须刀头部件,将其从剃须刀中
拉出。(图10)
4 用清洁刷清洁剃须刀头部件的内侧。(图11)
5 用清洁刷清洁胡茬储藏室。(图12)
6 将剃须刀头组件重新安装到剃须刀上。(图13)
每两个月:清洁剃须刀头
注意:请勿使用清洁剂或酒精来清洁剃须刀头。只
能使用飞利浦清洁喷雾剂(HQ110)。
1 关闭剃须刀电源,从电源插座中拔下电源插
头,并从剃须刀上拔出小插头。
2 垂直向上拉动剃须刀头部件,将其从剃须刀中
拉出。(图10)
3 要取下固定架,请捏拢中央弹簧的两侧(1)。然
后向上提起固定架,将其从剃须刀头部件中取
出(2)。
(图14)
4 将剃须刀头滑离固定架。一次取下并清洁一个
剃须刀头。每个剃须刀头包含一组刀片和网
罩。(图15)
注意:不要同时清洁多组刀片和网罩,因为它们都
是相互匹配的。如果不小心将刀片和网罩弄混,则
需要数周时间才能恢复产品的最佳剃须性能。
5 从刀片上卸下网罩。(图16)
6 用清洁刷的短毛一侧清洁刀片。按箭头方向小
心地清洁。(图17)
7 用清洁刷的长毛一侧清洁网罩。
(图18)
8 清洁后,将刀片重新装回至网罩。
(图19)
9 滑动剃须刀头,将其重新安装到固定架上。(
图20)
10将固定架重新安装到剃须刀头部件上(可听
到“咔嗒”一声)。
(图21)
11 将剃须刀头组件重新安装到剃须刀上。(图13)
存储
保持器具干燥。
必须在 5°C 至 35°C 之间的温度下使用和存放本
产品。
充电
请确保开始充电前,剃须刀电源已关闭。
如果是第一次为剃须刀充电,或是长时间未使用后
充电,应让其连续充电 12 小时。充电通常需要约
8 小时。当马达停止运转或开始运转缓慢时,应为
产品充电。
不要将本产品与电源接通超过24小时。
1 将小插头插入剃须刀。(图3)
2 将电源插头接入插座。
, 充电指示灯亮起,表示剃须刀正在充电。(图4)
3 电池充满后,从电源插座中拔下电源插头,并
从剃须刀上拔出小插头。(图5)
注意:本剃须刀不能插电使用。当电池电量耗尽
时,请在再次使用剃须刀前为电池充电。
不接电源的剃须时间
完全充电的剃须刀在不连接电源的情况下最长可使
用达 30 分钟。
使用本产品
剃须刀不能连在电源上直接使用。
1 取下保护盖。
2 向上推动开/关滑钮以接通剃须刀电源。(图6)
3 将剃须刀头在皮肤上移动。作直线和迂回动
作。(图7)
注意:仅限在干爽的面部剃须。请勿将本剃须刀与
凝胶、剃须泡沫或水结合使用。
注意:您的皮肤可能需要2到3周才能适应飞利浦
剃须系统。
4 向下推动开/关滑钮以关闭剃须刀电源。
5 每次剃须后均应清洁剃须刀(见“清洁和保
养”一章)。
6 请盖上剃须刀保护盖,以防止损坏剃须刀头并
避免其内积聚灰尘。
(图8)
清洁和保养
不要使用钢丝绒、研磨性清洁剂或腐蚀性液体(例
如汽油或丙酮)来清洁产品。
每次剃须后均应清洁剃须刀,以保证更好的剃须效
果。为了获得最佳的清洁效果,建议您使用飞利浦
清洁喷雾剂 (HQ110)。有关详情,请咨询飞利浦经
销商。
注意:并非所有国家/地区都销售飞利浦剃须刀头清
洁喷雾剂(HQ110)。请向当地的客户服务中心了解
是否有售。
简体中文
简介
感谢您的惠顾,欢迎光临飞利浦!为了您能充分
享受飞利浦提供的支持,请在 www.philips.com/
welcome 上注册您的产品。
一般说明 (图 1)
1 保护盖
2 剃须刀头
3 剃毛刀头部件
4 固定架
5 固定架的中央弹簧
6 毛发储藏室
7 开/关滑钮
8 前面板
9 充电指示灯
10 小插头的转换插座
11 清洁刷
12 飞利浦清洁喷雾剂 (HQ 110)
(可选)
13 小插头
14 带插头的电源线
15 刀片
16 网罩
注意事项
使用产品之前,请仔细阅读本用户手册,并妥善保
管以供日后参考。
危险
- 保持产品和电源线干燥。
- 警告符号注释:禁止用在打开的水龙头下进行
清洗。 (图 2)
警告
- 本产品不打算由肢体不健全、感觉或精神上有
障碍或缺乏相关经验和知识的人(包括儿童)
使用,除非有负责他们安全的人对他们使用本
产品进行监督或指导。
- 应照看好儿童,确保他们不玩耍本产品。
- 如果剃须刀或电源线已损坏,请勿再使用。
- 电源软线不能更换,如果软线损坏,此器具(
电源适配器)应废弃。如果电源软线损坏,则
必须用原装型号替换,以免发生危险。
注意
- 必须在 5 摄氏度至 35 摄氏度之间的温度下使
用、存放和为本产品充电。
- 仅使用随附的电源线为产品充电。
- 仅限使用随附的清洁刷。
- 确保清洁刷保持洁净。
电磁场 (EMF)
这款飞利浦产品符合关于电磁场 (EMF) 的相关标
准。据目前的科学证明,如果正确使用并按照本用
户手册中的说明进行操作,本产品是安全的。
Problem Possible cause Solution
The
appliance
makes a
strange
noise.
Too much dirt
has collected
in the shaving
heads.
Clean the shaving
heads. After cleaning,
lubricate the central
point on the inside
of the guards with
Philips Cleaning
Spray (HQ110). See
chapter ‘Cleaning and
maintenance’.
The shaving
heads are
damaged or
worn.
Replace the shaving
heads. See chapter
‘Replacement’.
有飞利浦客户服务中心,请与当地的飞利浦经销商
联系。
保修条款
由于剃须刀头(刀片和网罩)属于易磨损物品,因
此不在国际保修条款的涵盖范围之列。
故障种类和处理方法
本章归纳了使用本产品时最可能遇到的问题。如果
您无法根据下面的信息解决问题,请联系您所在国
家/地区的飞利浦客户服务中心。
问题 可能的原因 解决方法
剃须刀
的剃须
效果没
有以前
好。
剃须刀头变脏。
您没有将剃须刀
清洁干净,或长
时间未清洁过剃
须刀。
在继续剃须之前,
请先彻底清洗剃须
刀。见“清洁和保
养”一章。
过长的胡须堵塞
了剃须刀头。
用随附的清洁刷清
洁刀片和网罩。
见“清洁和保养”
中“每两个月:剃
须刀头”部分。
剃须刀头已损坏
或磨损。
更换剃须刀头。
见“更换”一章。
向上推
动开/
关滑钮
时剃须
刀不工
作。
电池已耗尽。 给电池充电。见“
充电”一章。
我在剃
须后出
现皮肤
过敏。
您的皮肤需要一
定的时间来适应
飞利浦剃须刀。
在前 2-3 周的使用
过程中,可能会出
现皮肤过敏。在此
之后,皮肤过敏通
常会消失。
剃须刀
头的转
速比平
时慢。
剃须刀头中积聚
了太多的灰尘。
清洁剃须刀头。请
参阅“清洁和保
养”一章。
电池已耗尽 给电池充电。见“
充电”一章。
产品发
出奇怪
的噪
音。
剃须刀头中积聚
了太多的灰尘。
清洁剃须刀头。清
洁后,用飞利浦清
洁喷雾剂 (HQ110)
润滑网罩内侧的中
央点。请参阅“清
洁和保养”一章。
剃须刀头已损坏
或磨损。
更换剃须刀头。
见“更换”一章。
1 关闭剃须刀。
2 使用后请盖上剃须刀保护盖,以防止损坏剃须
刀头并避免其内积聚灰尘。(图8)
更换
每两年更换一次刀头以获得最佳的剃须效果。
只能使用飞利浦剃须刀头(适用于中国的 HQ4+ 或
适用于世界其他各地的 HQ56)更换损坏或磨损的
剃须刀头。
有关如何拆卸剃须刀头的说明,请参阅“清洁和保
养”一章中的“每两个月:清洁剃须刀头”部分。
附件
为了保持剃须刀的最佳性能,请确保定期清洁并在
推荐的时间更换剃须刀头。
剃须刀头
- 建议您每两年更换一次剃须刀头。务必仅使用
飞利浦剃须刀头(适用于中国的 HQ4+ 或适用
于世界其他各地的 HQ56)进行更换。 (图 22)
清洁
- 使用飞利浦清洁喷雾剂 (HQ110) 彻底清洁剃须
刀头。
环保
- 弃置产品时,请不要将其与一般生活垃圾堆放
在一起;应将其交给官方指定的回收点。这样
做有利于环保。 (图 23)
- 内置充电电池包含可能会污染环境的物质。丢
弃剃须刀时,一定要将电池取出,并将剃须
刀送到官方指定的回收站。到官方指定的电池
回收站处理电池。如果您在取出电池时遇到问
题,您也可以将剃须刀送至飞利浦维修中心。
维修中心的员工会帮您取出电池,并以环保的
方式处理它。 (图 24)
卸下充电电池
电池电量完全耗尽后方可取出充电电池。
1 从电源插座上拔下插头,并从剃须刀上拔出小
插头。
2 让剃须刀一直运行直到停止,拧开剃须刀背面
的螺丝钉(1)并将后面板从剃须刀上卸除(2)。(
图25)
3 取出充电电池(图26)
取出电池之后,不要再将剃须刀与电源连接在一
起。
保修与服务
如果您需要服务或信息,或有任何疑问,请访问飞
利浦网站:www.philips.com。您也可与所在国家/
地区的飞利浦客户服务中心联系(可从全球保修卡
中找到其电话号码)。如果您所在的国家/地区没
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Philips PQ215/16 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル

他の言語で