2. Hilti
  3. SC 55W
SC 55W

Hilti SC 55W ユーザーマニュアル

  • Hilti SC 55W 丸のこの取扱説明書の内容を理解しました。この製品の使用方法、安全上の注意、メンテナンス方法など、あらゆる質問にお答えします。このドキュメントには、ワイヤレスデータ転送、無負荷時の定格速度、保護クラスII（二重絶縁）などの重要な機能が記載されています。お気軽にご質問ください。
  • SC 55Wのシリアル番号はどこに記載されていますか？
    キックバックとは何ですか？どのように防止できますか？
    下部ガードの機能は何ですか？
SC 55W
English 1
日本語 12
繁體中文 23
1
2
3
4
5
6
7
8
9
10
11
12
SC 55W
en Originaloperatinginstructions....................................... 1
ja オリジナル取扱説明書 ............................................ 12
zh 原始操作說明.................................................. 23
*2092691* 2092691 English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used:
DANGER
DANGER !
▶Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING
WARNING !
▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.
CAUTION
CAUTION !
▶Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage
to the equipment or other property.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use.
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household waste
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions
The numbering reflects the sequence of operations shown in the illustrations and may deviate
from the steps described in the text
Item reference numbers are used in the overview illustrations and refer to the numbers used in
the product overview section
This symbol is intended to draw special attention to certain points when handling the product.
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols can be used on the product:
2 English 2092691 *2092691*
Wireless data transfer
Rated speed under no load
Protection class II (double-insulated)
Saw blade
1.4 Product information
products are designed for professional users and only trained, authorized personnel are
permitted to operate, service and maintain the products. This personnel must be specifically informed about
the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by
untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
▶Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Circular saw SC 55W
Generation 01
Serial no.
1.5 Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives
and standards. A copy of the declaration of conformity can be found at the end of this documentation.
The technical documentation is filed here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany
2 Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.
▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Electrical safety
▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
*2092691* 2092691 English 3
▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a
dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will
reduce personal injuries.
▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energising power tools that have the switch on invites accidents.
▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
▶If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore
tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power tool use and care
▶Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from
the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Service
▶Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
2.2 Safety instructions for all saws
Cutting procedures
▶DANGER: Keep hands away from cutting area and the blade. Keep your second hand on
auxiliary handle or motor housing. If both hands are holding the saw, they cannot be cut by the blade.
▶Do not reach underneath the workpiece. The guard cannot protect you from the blade below the
workpiece.
▶Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
▶Never hold the workpiece in your hands or across your leg while cutting. Secure the workpiece
to a stable platform. It is important to support the work properly to minimise body exposure, blade
binding, or loss of control.
4 English 2092691 *2092691*
▶Hold the power tool by insulated gripping surfaces, when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will also make
exposed metal parts of the power tool "live" and could give the operator an electric shock.
▶When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
▶Always use blades with correct size and shape (diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw will run off-centre, causing loss of control.
▶Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and safety of operation.
Kickback causes and related warnings
• kickback is a sudden reaction to a pinched, jammed or misaligned saw blade, causing an uncontrolled
saw to lift up and out of the workpiece toward the operator;
• when the blade is pinched or jammed tightly by the kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the operator;
• if the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig
into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the
operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided
by taking proper precautions as given below.
▶Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces.
Position your body to either side of the blade, but not in line with the blade. Kickback could cause
the saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions
are taken.
▶When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the
saw motionless in the material until the blade comes to a complete stop. Never attempt to remove
the saw from the work or pull the saw backward while the blade is in motion or kickback may
occur. Investigate and take corrective actions to eliminate the cause of blade binding.
▶When restarting a saw in the workpiece, centre the saw blade in the kerf so that the saw teeth are
not engaged into the material. If a saw blade binds, it may walk up or kickback from the workpiece as
the saw is restarted.
▶Support large panels to minimise the risk of blade pinching and kickback. Large panels tend to sag
under their own weight. Supports must be placed under the panel on both sides, near the line of cut and
near the edge of the panel.
▶Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf
causing excessive friction, blade binding and kickback.
▶Blade depth and bevel adjusting locking levers must be tight and secure before making the cut. If
blade adjustment shifts while cutting, it may cause binding and kickback.
▶Use extra caution when sawing into existing walls or other blind areas. The protruding blade may
cut objects that can cause kickback.
Lower guard function
▶Check the lower guard for proper closing before each use. Do not operate the saw if the lower
guard does not move freely and close instantly. Never clamp or tie the lower guard into the open
position. If the saw is accidentally dropped, the lower guard may be bent. Raise the lower guard with
the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all
angles and depths of cut.
▶Check the operation of the guard return spring. If the guard and the spring are not operating
properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged
parts, gummy deposits, or a build-up of debris.
▶The lower guard may be retracted manually only for special cuts such as "plunge cuts" and
"compound cuts". Raise the lower guard by the retracting handle and as soon as the blade enters
the material, the lower guard must be released. For all other sawing, the lower guard should operate
automatically.
▶Always observe that the lower guard is covering the blade before placing the saw down on bench
or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its
path. Be aware of the time it takes for the blade to stop after switch is released.
*2092691* 2092691 English 5
2.3 Additional safety instructions for circular saws
▶Bring the saw blade into contact with the workpiece only when the circular saw is switched on.
➥ The path of the saw must be free of obstructions above and below the workpiece. Do not saw into
screws, nails or similar objects.
▶Never work overhead with a circular saw.
▶Never attempt to brake the saw blade by applying lateral pressure.
▶Avoid overheating the tips of the saw blade teeth.
▶When cutting plastic, avoid melting the plastic.
▶Always use a saw blade that is suitable for the material you are going to saw.
▶Use only saw blades recommended by Hilti that comply with the EN 847-1 standard.
3 Description
3.1 Product overview 1
@Single-arm fence
;Cutting angle setting
=Spindle lock button
%Auxiliary grip
&On/off switch
(Switch-on interlock release button
)Grip
+Electric supply cable
§Clamping lever for cutting depth adjustment
/Hex key
:Small base plate
∙LED illumination
$Front clamping lever for the fence
£Clamping lever for cutting angle adjustment
|Cutting depth scale
¡Hose connector (vacuum cleaner)
QGuard
WPivoting guard operating lever
ERear clamping lever for the fence (only with
large base plate)
RPivoting guard
TArbor
ZDirection-of-rotation arrow
UTwin-arm fence
I0° cutting line indicator
O45° cutting line indicator
PCutting angle scale
ÜLarge base plate
[Clamping screw
]Clamping flange
ÆMounting flange
º0° indicator on the base plate
~1°- 50° indicator on the base plate
3.2 Overview of the guide rail adapter 2
ARear retaining lug
SFront retaining lug
D0° indicator
F1°- 50° indicator
6 English 2092691 *2092691*
3.3 Intended use
The product described is a circular saw. It is designed for cutting wood or wood-like materials, plastics,
gypsum plasterboard, gypsum fiberboard and composite materials, up to a cutting depth of 55 mm, and for
miter cuts at angles up to 50°.
3.3.1 Possible misuse
Do not use saw blades not compliant with the technical data and do not use cutting discs, abrasive wheels
or saw blades made of highly alloyed high speed steel (HSS steel). Do not use this power tool to saw metal.
3.4 Items supplied
Circular saw, saw blade, hex key, rip fence, operating instructions.
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare
parts, consumables and accessories approved by Hilti for use with the product can be found at your
local Hilti Store or online at: www.hilti.group
4 Technical data
4.1 Technical data
For rated voltage, frequency, current and input power, please refer to the country-specific type
identification plate.
If the device is powered by a generator or transformer, the generator or transformer’s power output must be
at least twice the rated input power shown on the rating plate of the device. The operating voltage of the
transformer or generator must always be within +5 % and -15 % of the rated voltage of the device.
Weight, small base plate 4.5 kg
Weight, large base plate 4.7 kg
Saw blade diameter 160 mm … 165 mm
Saw blade disc thickness 1.1 mm … 1.5 mm
Saw blade arbor size 20 mm
Cutting depth at 0° 0 mm … 55 mm
Cutting depth at 45° 0 mm … 41 mm
Cutting depth at 50° 0 mm … 37 mm
No-load speed 5,500 /min
4.2 Noise information and vibration values in accordance with EN 62841
The sound pressure and vibration values given in these instructions were measured in accordance with a
standardized test and can be used to compare one power tool with another. They can also be used for a
preliminary assessment of exposure.
The data given represent the main applications of the power tool. However, if the power tool is used for
different applications, with different accessory tools, or is poorly maintained, the data can vary. This can
significantly increase exposure over the total working period.
An accurate estimation of exposure should also take into account the times when the tool is switched off, or
when it is running but not actually being used for a job. This can significantly reduce exposure over the total
working period.
Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for
example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work
patterns.
Noise information
Sound power level (LWA)101 dB(A)
Sound pressure level (LpA)90 dB(A)
Uncertainty 3 dB(A)
*2092691* 2092691 English 7
Vibration information
230 V 110 V
Triaxial vibration value when cutting wood (ah)1.77 m/s²
(5.81 ft/s²)
2.12 m/s²
(6.96 ft/s²)
Uncertainty (K) 1.5 m/s² 1.5 m/s²
5 Operation
5.1 Removing the saw blade 3
WARNING
Risk of burning injury. A hot accessory tool, clamping flange or clamping screw and the sharp edges of the
saw blade present hazards.
▶Wear protective gloves when changing saw blades.
1. Disconnect the supply cord plug from the power outlet.
2. Insert the hex key into the saw blade securing screw.
3. Press the drive spindle lock button and hold it in this position.
4. Turn the saw blade clamping screw with the hex key until the spindle lock button engages fully.
5. Release the clamping screw by turning the hex key in the direction of the direction-of-rotation arrow.
6. Remove the clamping screw from the outer clamping flange.
7. Open the pivoting guard by swinging it to the side and then remove the saw blade.
If necessary, the mounting flange can be removed for cleaning.
5.2 Install saw blade 4
CAUTION
Risk of damage Unsuitable or incorrectly fitted saw blades may damage the saw.
▶Only use blades which are suitable for this saw. Observe the direction-of-rotation arrow on the saw
blade.
▶Use only saw blades equipped with a rated maximum permissible speed that is at least as high as the
maximum speed stated on the product.
1. Disconnect the supply cord plug from the power outlet.
2. Clean the mounting flange and the clamping flange.
3. Fit the outer clamping flange the right way round (i.e. facing the right direction).
4. Open the pivoting guard.
5. Fit the new saw blade.
6. Install the outer clamping flange the right way round.
7. Insert the clamping screw.
8. Insert the hex key into the saw blade clamping screw.
9. Secure the clamping flange with the clamping screw by turning it clockwise. At the same time, use one
hand to hold down the arbor lock button.
10. Before using the power tool, check that the saw blade is correctly seated and tightened securely.
5.3 Adjusting the cutting depth 5
1. Disconnect the supply cord plug from the power outlet.
2. Release the cutting depth adjustment clamping lever.
3. Lift the circular saw in a scissoring movement and set the cutting depth.
➥ The cutting depth is shown on the cutting depth scale.
For a clean-edged cut, set cutting depth to the thickness of the material plus 2 mm.
4. Secure the cutting depth adjustment clamping lever.
8 English 2092691 *2092691*
5.4 Setting the miter cut angle 6
1. Disconnect the supply cord plug from the power outlet.
2. Release the cutting angle adjustment clamping lever.
3. Pivot the base plate to the desired miter cut angle.
➥ The miter cutting angle is shown on the miter cut angle scale.
4. Tighten the cutting angle adjustment clamping lever.
5.5 Cutting line indicator
At the front edge of the base plate of the circular saw is a line indicator for straight cuts and miter cuts (0°
and 45°). This permits accurate cutting at the desired miter angle. The edge of the line indicator corresponds
to the inside of the saw blade. There is a cutting line indicator at the opening for the saw blade at the front
end of the base plate.
5.5.1 Sawing along a line 7
Secure the workpiece to prevent movement.
Position the workpiece so that the saw blade is free to rotate beneath it.
Check that the on/off switch on the product is in the “off” position.
Position the forward section of the circular saw’s base plate on the workpiece but do not bring the
blade into contact with the workpiece.
1. Switch on the circular saw.
2. Guide the circular saw along the cutting line on the workpiece at a suitable speed.
5.6 Sawing with the fence 8
The single-arm fence can be used to make accurate cuts along the edge of a workpiece or to rip strips of
equal width. The fence can be fitted on either side of the base plate.
The twin-arm fence can be used only with the large base plate
When installing the fence, make sure that it is installed right way round.
5.7 Sawing with the guide rail.
Sawing with the guide rail can reduce the risk of kickback.
5.7.1 Inserting into / removing from the guide rail adapter 9
When using saws with a small base plate, please use a guide rail adapter that fits the guide rail.
1. Remove the fence, if one is fitted.
2. Fit the base plate into the rear retaining lugs of the guide rail adapter.
3. Bring the front edge of the base plate down fully into the guide rail adapter. The base plate must engage
fully with the front retaining lug.
4. To remove, pull the front retaining lug forward slightly and remove the circular saw from the guide rail
adapter.
5.7.2 Longitudinal cuts at 0° 10
▶Place the circular saw on the guide rail with the groove marked “0°” on the rib on the rail.
5.7.3 Longitudinal cuts at angles up to 50° 11
CAUTION
Risk of damage If the saw is engaged in the wrong groove, the saw blade will collide with the guide rail.
▶Place the saw in the correct groove.
▶Place the saw on the guide rail with the groove marked “1°- 50°” on the rib on the rail.
*2092691* 2092691 English 9
5.7.4 Using the saw on the guide rail 12
1. Secure the guide rail from below with two screw clamps.
2. Position the circular saw on the guide rail a short distance from the starting point of the cut. Open the
guard manually when making longitudinal cuts (ripping) at cutting angles of 20°- 50°.
The saw must be placed on the guide rail behind the workpiece.
Take care to ensure that the saw blade is not in contact with the workpiece.
3. Switch on the circular saw.
4. Push the saw at a steady speed across the workpiece.
➥ At cutting angles under 20° the pivoting guard opens automatically when it makes contact with the
lateral actuating edge.
➥ It closes again automatically when the saw leaves the end of the guide rail.
5.8 Sawing with or without sawdust extraction
The circular saw has a connector that fits common types of vacuum cleaner hose with a diameter of 27 mm.
A suitable adapter might be required for connecting the vacuum-cleaner hose to the circular saw.
If possible, always use a suitable mobile dust removal system for wood and wood and mineral materials.
If you are working without a sawdust extractor, turn the ejector so that the sawdust is directed away from you.
Always use a filter class P2 dust mask and always ensure adequate ventilation to help minimize
exposure to dust.
6 Care and maintenance
6.1 Care and maintenance
WARNING
Electric shock hazard! Attempting care and maintenance with the supply cord connected to a power outlet
can lead to severe injury and burns.
▶Always unplug the supply cord before carrying out care and maintenance tasks.
Care
• Carefully remove any dirt that may be adhering to parts.
• Clean the air vents carefully with a dry brush.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as
these may attack the plastic parts.
Maintenance
WARNING
Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including
burns.
▶Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical
specialists.
• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all
function correctly.
• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired
immediately by Hilti Service.
• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare
parts, consumables and accessories approved by Hilti for use with the product can be found at your
local Hilti Store or online at: www.hilti.group.
6.2 Checks after cleaning and maintenance
After cleaning or maintenance, check that all safety devices are fitted and that they function faultlessly.
10 English 2092691 *2092691*
▶To check the pivoting guard, open the guard fully by moving the guard operating lever.
➥ The pivoting guard must close quickly and completely when the guard operating lever is released.
6.3 Cleaning the ejector
The saw blade must be removed during cleaning if necessary.
1. Disconnect the supply cord plug from the power outlet.
2. Remove the saw blade. → page 7
3. Clean the ejector.
4. Install the saw blade. → page 7
5. Check that moving parts are in full working order and do not jam and make sure there are no parts that
are broken or damaged in such a way as to impair operation of the power tool.
6.4 Cleaning the guard
1. Remove the saw blade. → page 7
2. Clean the parts of the guard carefully with a dry brush.
3. Use a suitable tool to remove deposits or cuttings from the inside surfaces of the parts of the guard.
4. Install the saw blade. → page 7
7 Troubleshooting
Trouble or fault Possible cause Action to be taken
The power tool does not de-
velop full power.
The extension cord is too long or
its gauge is inadequate.
▶Use an extension cord of an
approved length and/or of
adequate gauge.
The voltage provided by the elec-
tric supply is too low.
▶Connect the power tool to a
different electric supply.
The power tool does not
work.
Interruption in the electric supply. ▶Plug in another power tool or
appliance and check whether it
works.
The supply cord or plug is defec-
tive.
▶Have the power cord or the plug
checked by a trained electrical
specialist, and if necessary
replaced by Hilti service.
The on / off switch is defective. ▶Have the product repaired by
Hilti Service.
The carbon brushes are worn. ▶Have the product repaired by
Hilti Service.
No suction power or reduced
suction power
The chip ejector channel is
blocked.
▶Clean the ejector. → page 10
The pivoting guard does not
close.
Safety device is clogged. ▶Clean the guard. → page 10
The power tool vibrates more
than usual.
The saw blade is fitted incorrectly. ▶Remove the saw blade and
install it again correctly.
8 Disposal
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
▶Do not dispose of power tools, electronic equipment or batteries as household waste!
*2092691* 2092691 English 11
9 RoHS (Restriction of Hazardous Substances)
Click on the link to go to the table of hazardous substances: qr.hilti.com/r2937786.
There is a link to the RoHS table, in the form of a QR code, at the end of this document.
10 Manufacturer’s warranty
▶Please contact your local Hilti representative if you have questions about the warranty conditions.
12 日本語 2092691 *2092691*
1 文書について
1.1 本書について
• ご使用前に本書をすべてお読みください。このことは、安全な作業と問題のない取扱いのための前提条
件となります。
• 本書および製品に記載されている安全上の注意と警告表示に注意してください。
• 取扱説明書は常に製品とともに保管し、他の人が使用する場合には、製品と取扱説明書を一緒にお渡し
ください。
1.2 記号の説明
1.2.1 警告表示
警告表示は製品の取扱いにおける危険について警告するものです。以下の注意喚起語が使用されています：
危険
危険 ！
▶この表記は、重傷あるいは死亡事故につながる危険性がある場合に注意を促すために使われます。
警告
警告 ！
▶この表記は、重傷あるいは死亡事故につながる可能性がある場合に注意を促すために使われます。
注意
注意 ！
▶この表記は、軽傷あるいは物財の損傷が発生する可能性がある場合に使われます。
1.2.2 本書の記号
本書では、以下の記号が使用されています：
使用前に取扱説明書をお読みください
本製品を効率良く取り扱うための注意事項や役に立つ情報
リサイクル可能な部品の取扱い
工具およびバッテリーを一般ゴミとして廃棄してはなりません
1.2.3 図中の記号
図中では以下の記号が使用されています：
この数字は本取扱説明書冒頭にある該当図を示しています
付番は図中の作業手順の順序に対応していて、本文の作業手順とは一致しない場合があります
概要図には項目番号が付されていて、製品概要セクションの凡例の番号に対応しています
この記号は、製品の取扱いの際に特に注意が必要なことを示しています。
1.3 製品により異なる記号
1.3.1 製品に表示されている記号
製品には以下の記号が使用されていることがあります：
無線データ転送
無負荷回転数
*2092691* 2092691 日本語 13
電気絶縁保護クラス II（二重絶縁）
ソーブレード
1.4 製品情報
製品はプロ仕様で製作されており、その使用、保守、修理を行うのは、認定を受けトレーニング
された人のみに限ります。これらの人は、遭遇し得る危険に関する情報を入手していなければなりません。
製品およびアクセサリーの使用法を知らない者による誤使用、あるいは規定外の使用は危険です。
機種名および製造番号は銘板に表示されています。
▶製造番号を以下の表に書き写しておいてください。ヒルティ代理店やサービスセンターへお問い合わせ
の際には、製品データが必要になります。
製品データ
サーキュラーソー SC 55W
製品世代 01
製造番号
1.5 適合宣言
当社は、単独の責任において本書で説明している製品が有効な基準と標準規格に適合していることを宣言し
ます。適合宣言書の複写は本書の末尾にあります。
技術資料は本書の後続の頁に記載されています：
Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE
2 安全
2.1 電動工具の一般安全注意事項
警告事項 本電動工具に付属のすべての安全上の注意、指示事項、図、および製品仕様をお読みくださ
い。以下の指示を守らないと、感電、火災および／または重傷事故の危険があります。
安全上の注意および指示事項が書かれた説明書はすべて大切に保管してください。
安全上の注意で使用する用語「電動工具」とは、お手持ちの電動ツール（電源コード使用）またはバッテリー
ツール（コードレス）を指します。
作業環境に関する安全
▶作業場はきれいに保ち、十分に明るくしてください。ちらかった暗い場所での作業は事故の原因となり
ます。
▶爆発の危険性のある環境（可燃性液体、ガスおよび粉じんのある場所）では電動工具を使用しないでく
ださい。電動工具から火花が飛散し、粉じんや揮発性ガスに引火する恐れがあります。
▶電動工具の使用中、子供や無関係者を作業場へ近づけないでください。作業中に気がそらされると、
本体のコントロールを失ってしまう恐れがあります。
電気に関する安全注意事項
▶電動工具の接続プラグは電源コンセントにきちんと適合しなければなりません。プラグは絶対に変更し
ないでください。保護接地した電動工具と一緒にアダプタープラグを使用しないでください。オリジナ
ルのプラグと適切なコンセントを使用することにより、感電の危険を小さくすることができます。
▶パイプ、ラジエーター、電子レンジ、冷蔵庫などのアースされた面に体の一部が触れないようにしてく
ださい。体が触れると感電の危険が大きくなります。
▶電動工具を雨や湿気から保護してください。電動工具に水が浸入すると、感電の危険が大きくなります。
▶電動工具を持ち運んだり、吊り下げたり、コンセントからプラグを抜いたりするときは、必ず本体を持
ち、電源コードを持ったり引っ張ったりしないでください。電源コードを火気、オイル、鋭利な刃物、
可動部等に触れる場所に置かないでください。電源コードが損傷したり絡まったりしていると、感電の
危険が大きくなります。
▶屋外工事の場合には、必ず屋外専用の延長コードを使用してください。屋外専用の延長コードを使用す
ると、感電の危険が小さくなります。
▶湿った場所で電動工具を作動させる必要がある場合は、漏電遮断器を使用してください。漏電遮断器を
使用すると、感電の危険が小さくなります。
14 日本語 2092691 *2092691*
作業者に関する安全
▶電動工具を使用の際には、油断せずに十分注意し、常識をもった作業をおこなってください。疲れてい
る場合、薬物、医薬品服用およびアルコール飲用による影響下にある場合には電動工具を使用しないで
ください。電動工具使用中の一瞬の不注意が重傷の原因となることがあります。
▶個人用保護具および保護メガネを常に着用してください。負傷の危険を低減するために、電動工具の使
用状況に応じた粉じんマスク、耐滑性の安全靴、ヘルメット、耳栓などの個人用保護具を着用してくだ
さい。
▶電動工具の意図しない始動を防止して下さい。電動工具を電源および／またはバッテリーに接続する前
や本体を持ち上げたり運んだりする前に、本体がオフになっていることを必ず確認してください。オン
／オフスイッチが入っている状態で電動工具のスイッチに指を掛けたまま運んだり、電源に接続したり
すると、事故の原因となる恐れがあります。
▶電動工具のスイッチを入れる前に、必ず調節キーやレンチを取り外してください。調節キーやレンチが
本体の回転部に装着されたままでは、けがの原因となる恐れがあります。
▶作業中は不安定な姿勢をとらないでください。足元を安定させ、常にバランスを保つようにしてくださ
い。これにより、万一電動工具が異常状況に陥った場合にも、適切な対応が可能となります。
▶作業に適した作業着を着用してください。だぶだぶの衣服や装身具を着用しないでください。髪、衣服、
手袋を本体の可動部に近づけないでください。だぶだぶの衣服、装身具、長い髪が可動部に巻き込まれ
る恐れがあります。
▶吸じんシステムの接続が可能な場合には、これらのシステムが適切に接続、使用されていることを確認
してください。吸じんシステムを利用することにより、粉じん公害を防げます。
▶電動工具の取扱いに熟練している場合にも、正しい安全対策を遵守し、電動工具に関する安全規則を無
視しないでください。不注意な取扱いは、ほんの一瞬で重傷事故を招くことがあります。
電動工具の使用および取扱い
▶無理のある使用を避けてください。作業用途に適した電動工具を使用してください。適切な電動工具の
使用により、能率よく、スムーズかつ安全な作業が行えます。
▶スイッチが故障している場合には、電動工具を使用しないでください。スイッチで始動および停止操作
のできない電動工具は危険ですので、修理が必要です。
▶本体の設定やアクセサリーの交換を行う前や本体を保管する前には電源プラグをコンセントから抜き、
および／または脱着式のバッテリーを取り外してください。この安全処置により、電動工具の意図しな
い始動を防止することができます。
▶電動工具をご使用にならない場合には、子供の手の届かない場所に保管してください。電動工具に関す
る知識のない方、本説明書をお読みでない方による本体のご使用は避けてください。未経験者による電
動工具の使用は危険です。
▶電動工具とアクセサリーは慎重に手入れしてください。可動部分が引っ掛かりなく正常に作動している
か、電動工具の運転に影響を及ぼす各部分が破損・損傷していないかを確認してください。電動工具を
ご使用になる前に、損傷部分の修理を依頼してください。事故の多くは保守管理の不十分な電動工具の
使用が原因となっています。
▶先端工具は鋭利で汚れのない状態を保ってください。お手入れのゆきとどいた先端工具を使用すると、
作業が簡単かつ、スムーズになります。
▶電動工具、アクセサリー、先端工具などは、それらの説明書に記載されている指示に従って使用してく
ださい。その際は、作業環境および用途についてもご注意ください。指定された用途以外に電動工具を
使用すると危険な状況をまねく恐れがあります。
▶グリップとグリップ面は乾燥した清潔な状態に保ち、オイルやグリスの付着がないようにしてくださ
い。グリップやグリップ面が滑りやすい状態になっていると、予期していない状況が発生した際に電動
工具を安全に使用／制御できません。
サービス
▶電動工具の修理は必ず認定サービスセンターにお申し付けください。また、必ず純正部品を使用してく
ださい。これにより電動工具の安全性が確実に維持されます。
2.2 すべてのソーに対する安全上の注意
切断作業
▶危険：切断領域やソーブレード付近に手を差し出さないでください。片方の手で補助グリップまたは
モーターハウジングを保持してください。両手でソーを保持すれば、ソーブレードで手を負傷すること
はありません。
▶作業材料の下側をつかまないでください。保護カバーは、作業材料の下側に出るソーブレードから手を
保護することはできません。
▶切り込み深さを作業材料の厚さに合わせてください。作業材料の下に出る部分を歯の全高より小さくし
てください。
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/