Christie 科视DWU2022-HS Installation Information
- カテゴリー
- データプロジェクター
- タイプ
- Installation Information
Christie HS Series 2K
DWU1612-HS/DWU2022-HS
Product Safety Guide
020-001786-01
Important Safety Information
2DWU1612-HS/DWU2022-HS Product Safety Guide
020-001786-01 Rev. 1 (03-2020)
Copyright ©2020 Christie Digital Systems USA Inc. All rights reserved.
Important Safety
Information
Read this document carefully before installing or
operating the DWU1612-HS/DWU2022-HS projectors.
Store the document in a location close to the projectors
for future reference.
Product documentation
For installation, setup, and user information, see the
product documentation available on the Christie website
at www.christiedigital.cn. Read all instructions before
using or servicing this product.
1. Access the documentation from the Christie
website:
•Go to this URL: https://www.christiedigital.cn/
zh-cn/business/products/projectors/1-chip
-dlp/hs-series
• Scan the QR code using a QR code reader app
on a smart phone or tablet.
2. On the product page, select the model and switch
to the Downloads tab.
Related documentation
Additional information on the projector is available in
the following documents.
• DWU1612-HS/DWU2022-HS Product Safety Guide
(P/N: 020-001786-XX)
• DWU1612-HS/DWU2022-HS Installation and Setup
Guide (P/N: 020-001787-XX)
• DWU1612-HS/DWU2022-HS User Manual
(P/N: 020-001788-XX)
• DWU1612-HS/DWU2022-HS Specification Guide
(P/N: 020-001789-XX)
• DWU1612-HS/DWU2022-HS Service Manual
(P/N: 020-001790-XX)
• DWU1612-HS/DWU2022-HS Serial Commands
Technical Reference (P/N: 020-103352-XX)
• DWU1612-HS/DWU2022-HS Lens Throw Ratios
Technical Reference (P/N: 020-103353-XX)
• DWU1612-HS/DWU2022-HS HSG Adjustment
Instruction Sheet (P/N: 020-103354-XX)
• DWU1612-HS/DWU2022-HS Lenses Technical
Bulletin (P/N: 020-200472-XX)
Model names
• DWU1612-HS
• DWU2022-HS
Notation
Learn the hazard and information symbols used in the
product documentation.
Product labels
Learn about the labels that may be used on the
product. Labels on your product may be yellow or black
and white.
General hazards
Hazard warnings also apply to accessories once they
are installed in a Christie product that is connected to
power.
Danger messages indicate a hazardous
situation which, if not avoided, results in
death or serious injury.
Warning messages indicate a hazardous
situation which, if not avoided, could result
in death or serious injury.
Caution messages indicate a hazardous
situation which, if not avoided, could result
in minor or moderate injury.
Notice messages indicate a hazardous
situation which, if not avoided, may result in
equipment or property damage.
Information messages provide additional
information, emphasize or provide a useful
tip.
Fire and Shock Hazard
To prevent fire or shock hazards, do not
expose this product to rain or moisture.
Do not alter the power plug, overload the
power outlet, or use it with extension Cords.
Do not remove the product enclosure.
Only Christie qualified technicians are
authorized to service the product.
Electrical Hazard
Risk of electric shock.
Do not remove the product enclosure.
Only Christie qualified technicians are
authorized to service the product.
Important Safety Information
3DWU1612-HS/DWU2022-HS Product Safety Guide
020-001786-01 Rev. 1 (03-2020)
Copyright ©2020 Christie Digital Systems USA Inc. All rights reserved.
Mandatory action
Electrical labels
Laser labels
This projector has been classified as Class 1 Laser
Product-Risk Group 3 according to the IEC 60825-
1:2014 and IEC 62471-5:2015 standard.
Additional safety hazard
Important safeguards
To prevent personal injury and to protect the device
from damage, read and follow these safety precautions.
This projector is intended for use in a non-cinema
environment.
Safety and warning guidelines
• Do not expose the product to moisture.
• Do not operate the product without all of its covers
in place.
• This product must be installed within a restricted
access location not accessible by the general public.
• Only personnel who are trained on the precautions
for the restricted access location can be granted
entry to the area.
• FIRE HAZARD! Keep hands, clothes, and all
combustible material away from the concentrated
light beam of the projector.
• TRIP OR FIRE HAZARD! Position all cables where
they cannot contact hot surfaces, be pulled, be
tripped over, or damaged by persons walking on or
objects rolling over the cables.
• SHOCK HAZARD! Disconnect the product from AC
before installing, moving, servicing, cleaning,
removing components, or opening any enclosure.
General hazard.
Electric shock hazard. To avoid personal
injury, disconnect all power sources before
performing maintenance or service.
Electrocution hazard. To avoid personal
injury, always disconnect all power sources
before performing maintenance or service.
Hot surface hazard. To avoid personal
injury, allow the product to cool for the
recommended cool down time before
performing maintenance or service.
Burn hazard. To avoid personal injury, allow
the product to cool for the recommended
cool down time before performing
maintenance or service.
Moving parts hazard. To avoid personal
injury, keep hands clear and loose clothing
tied back.
Fan hazard. To avoid personal injury, keep
hands clear and loose clothing tied back.
Always disconnect all power sources before
performing maintenance or service
procedures.
Voltage hazard. To avoid personal injury,
always disconnect all power sources before
performing maintenance or service
procedures.
Bright light hazard. To avoid personal injury,
never look directly at the light source.
Not for household use.
Consult the service manual.
Disconnect all power sources before
performing maintenance or service
procedures.
Indicates the presence of an earth ground.
FDA laser variance
(US projectors only)
Indicates a light hazard.
Do not look directly into
the lens. The extreme
high brightness can
cause permanent eye
damage. Class 1 Laser
Product-Risk Group 3
according to Class 1 IEC
60825-1:2014 and IEC
62471-5:2015.
Do not look directly into the lens.
The extremely high brightness can
cause permanent eye damage.
Warning! If not avoided, the following
could result in death or serious injury.
Christie Digital Systems Canada Inc.
809 Wellington Street North
Kitchener, ON N2G 4Y7
Canada
This product complies with performance standards for laser
products under 21 CFR Part 1040 except with respect to those
characteristics authorized by Variance Number 2016-V-1838
eective June 20, 2017.
U.S.A Only
Important Safety Information
4DWU1612-HS/DWU2022-HS Product Safety Guide
020-001786-01 Rev. 1 (03-2020)
Copyright ©2020 Christie Digital Systems USA Inc. All rights reserved.
• A minimum of four people or appropriately rated lift
equipment is required to safely lift, install, or move
the product.
• OPTICAL RADIATION HAZARD! Disconnect the
power plug from the AC outlet if the product is not
being used for an extended period of time.
• Do not allow anything to rest on the power cord.
• Always provide proper ventilation for the product to
prevent overheating.
• Only Christie qualified technicians are permitted to
open product enclosures.
• All procedures must be performed by Christie
qualified technicians.
• Always use a lens plug when installing or moving
the product. This prevents contaminants from
entering the product.
• Only use cleaning solutions recommended by
Christie. All other cleaning solutions may cause
product damage and will void the warranty.
Installation safety and warning guidelines
• High leakage current present when connected to IT
power systems.
• ELECTRICAL and BURN HAZARD! Use caution when
accessing internal components.
• Only Christie qualified technicians are authorized to
use the tools provided in the toolbox.
AC/power precautions
• FIRE HAZARD! Do not use a power cord, harness,
or cable that appears damaged.
• FIRE OR SHOCK HAZARD! Do not overload power
outlets and extension cords.
• SHOCK HAZARD! Only use the AC power cord
provided with the product or recommended by
Christie.
• FIRE AND SHOCK HAZARD! Do not attempt
operation unless the power cord, power socket, and
power plug meet the appropriate local rating
standards.
• SHOCK HAZARD! Do not attempt operation if the
AC supply is not within the specified voltage and
current, as specified on the license label.
• SHOCK HAZARD! The AC power cord must be
inserted into an outlet with grounding.
• SHOCK HAZARD! Disconnect the product from AC
before installing, moving, servicing, cleaning,
removing components, or opening any enclosure.
• Install the product near an easily accessible AC
receptacle.
Laser safety precautions
• PERMANENT/TEMPORARY BLINDNESS HAZARD! No
direct exposure to the beam must be permitted.
Class 1 Laser Product-Risk Group 3 according to
IEC 62471-5:2015.
• Possibly hazardous optical radiation emitted from
this product. (Risk Group 3)
• LASER RADIATION HAZARD! This projector has a
built-in Class 4 laser module. Never attempt to
disassemble or modify the laser module.
• Any operation or adjustment not specifically
instructed in the User manual creates the risk of
hazardous laser radiation exposure.
• Do not operate the product without all of its covers
in place.
• Do not look directly into the lens when the light
source is on. The extremely high brightness can
cause permanent eye damage.
• Only Christie qualified technicians who are
knowledgeable about the hazards associated with
laser use, high-voltage, and high temperatures
generated by the product are authorized to
assemble, install, and service the Christie Laser
Projection System.
Light intensity hazard distance
This projector has been classified as Risk Group 3
according to the IEC 62471-5:2015 standard due to
possible hazardous optical and thermal radiation being
emitted.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! No
direct exposure to the beam must be permitted.
• PERMANENT/TEMPORARY BLINDNESS HAZARD!
Operators must control access to the beam within
the hazard distance or install the product
preventing potential exposure of the spectators'
eyes from being in the hazard distance. Hazard
zone shall be no lower than 3.0 meters above the
floor. In addition, horizontal clearance to the hazard
zone shall be a minimum 2.5 meters.
Caution! If not avoided, the following
could result in minor or moderate injury.
Notice! If not avoided, the following could
result in equipment or property damage.
Warning! If not avoided, the following
could result in death or serious injury.
Caution! If not avoided, the following
could result in minor or moderate injury.
Warning! If not avoided, the following
could result in death or serious injury.
Warning! If not avoided, the following
could result in death or serious injury.
Warning! If not avoided, the following
could result in death or serious injury.
Important Safety Information
5DWU1612-HS/DWU2022-HS Product Safety Guide
020-001786-01 Rev. 1 (03-2020)
Copyright ©2020 Christie Digital Systems USA Inc. All rights reserved.
• EXTREME BRIGHTNESS! Do not place reflective
objects in the product light path.
The following diagram shows the zones for optical and
skin hazard distances:
• A—Hazard zone. The region of space where the
projection light from the laser-illuminated projector
is above emission limits for Risk Group 2. The light
intensity may cause eye damage after a
momentary or brief exposure (before a person can
avert his or her eyes away from the light source).
The light may cause skin burns to occur.
• B—Hazard distance. Operators must control access
to the beam within the hazard distance or install
the product preventing potential exposure of the
spectators' eyes from being in the hazard distance.
• C—No access zone. Horizontal clearance of the no
access zone must be a minimum of 2.5 meters.
• D—Vertical distance to hazard zone. The hazard
zone must be no lower than 3.0 meters above the
floor.
• E—Represents the top view of the projector.
• F—Represents the side view of the projector.
For information detailing the hazard distance for each
lens, refer to the
DWU1612-HS/DWU2022-HS
Installation and Setup Guide (P/N: 020-001787-XX)
or
DWU1612-HS/DWU2022-HS User Manual (P/N: 020-
1788-XX)
.
Power requirements
Learn about the power requirements for DWU1612-HS/
DWU2022-HS projectors.
Technical support
• North and South America: +1-800-221-8025 or
• Europe, Middle East, and Africa: +44 (0) 1189
778111 or Support.EMEA@christiedigital.com
• Asia Pacific: +65 6877-8737 or
Parameter Requirement
Power rating • DWU1612-HS:
200 - 240 VAC, 50/60 Hz, 7 A
•
DW
U20
22-HS:
200 - 240 VAC, 50/60 Hz, 9 A
AC input coupler C14
Inrush current 80 A Maximum @240 VAC
Power
consumption
• DWU1612-HS:
1410 W Maximum
• DW
U2022-HS:
1710 W Maximum
重要安全信息
6DWU1612-HS/DWU2022-HS 产品安全指南
020-001786-01 修订版 1 (03-2020)
Copyright ©2020 Christie Digital Systems USA Inc. 保留所有权利。
重要安全信息
请在安装或操作 DWU1612-HS/DWU2022-HS 投影机之前
仔细阅读此文档。请将此文档存放在投影机附近，以便用作将来
参考。
产品文档
有关安装、设置和用户信息，请参见 Christie网站
www.christiedigital.cn 中提供的产品文档。请在使用或维修
本产品前阅读全部说明。
1. 从 Christie 网站访问文档：
• 转至：https://www.christiedigital.cn/zh-cn/
business/products/projectors/1-chip-dlp/
hs-series
• 使用智能手机或平板电脑上的二维码读取应用程序扫
描二维码。
2. 在产品页面上，选择型号并切换至下载选项卡。
相关文档
有关投影机的详细信息，请参阅以下文档。
• DWU1612-HS/DWU2022-HS
产品安全指南
(P/N:020-001786-XX)
• DWU1612-HS/DWU2022-HS
安装和设置指南
(P/N:020-001811-XX)
• DWU1612-HS/DWU2022-HS
用户手册
(P/N:020-001798-XX)
• DWU1612-HS/DWU2022-HS Specification Guide
(P/N: 020-001789-XX)
• DWU1612-HS/DWU2022-HS Service Manual
(P/N: 020-001790-XX)
• DWU1612-HS/DWU2022-HS Serial Commands
Technical Reference (P/N: 020-103352-XX)
• DWU1612-HS/DWU2022-HS Lens Throw Ratios
Technical Reference (P/N: 020-103353-XX)
• DWU1612-HS/DWU2022-HS HSG Adjustment
Instruction Sheet (P/N: 020-103354-XX)
• DWU1612-HS/DWU2022-HS Lenses Technical
Bulletin (P/N: 020-200472-XX)
型号名称
• DWU1612-HS
• DWU2022-HS
符号
了解产品文档中所使用的危险和信息符号。
产品标签
了解产品中所使用的标签。产品标签可能为黄色或黑色与白色。
常规危险
危险警告也同样适用于安装在已接通电源的 Christie 产品配件。
危险消息指出如不避免一经发生将会导致死亡或造
成重伤的危险情况。
警告消息指出如不避免一经发生可能会导致死亡或
造成重伤的危险情况。
警示消息指出如不避免一经发生将会导致轻伤或造
成中度伤害的危险情况。
通知消息指出如不避免一经发生将会导致设备损坏
或财产损失的危险情况。
信息消息提供附加信息，以强调或提供有用的提
示。
火灾与电击危险
为防止火灾或电击危险，请勿使本产品接触雨水或
湿气。
请勿改动电源插头、使电源插座过载或将其与延长
线一起使用。
请勿拆下产品外壳。
仅合格的 Christie 技师有权对本产品进行维修。
电气危险
本品有电击风险。
请勿拆下产品外壳。
仅合格的 Christie 技师有权对本产品进行维修。
常规危险。
电击危险。为避免受到人身伤害，在进行维护或维
修前，请断开所有电源连接。
重要安全信息
7DWU1612-HS/DWU2022-HS 产品安全指南
020-001786-01 修订版 1 (03-2020)
Copyright ©2020 Christie Digital Systems USA Inc. 保留所有权利。
必要操作
电气标签
激光标签
根据 IEC 60825-1:2014 和 IEC 62471-5:2015 标准，此投
影机分类为1类激光产品，危害等级为3级。
其他安全危险
重要的安全防护措施
为防止人身伤害和设备受损，请阅读并遵循以下安全安全警示信
息。此投影机适合在非影院环境中使用。
安全和警告指南
• 请勿使本产品接触湿气。
• 操作本产品之前必须保证所有机盖均已就位。
• 此产品必须安装在公众无法接近的受限区域。
• 仅接受过受限区警示信息相关培训的人员有权进入该区
域。
• 火灾危险！确保手、衣服和所有可燃材料远离投影机的集
中光束。
• 绊倒或火灾危险！请将所有电缆置于不接触热表面、不被
拖拉、羁绊、不被人踩踏或物体滚压的位置。
• 电击危险！在安装、移动、维修、清洁、取下组件或打开
任何外壳之前，请断开产品上的交流电源。
• 为了安全地抬起、安装或移动产品，至少需要四个人或使
用适当速度的升降设备。
• 光辐射危险！如果本产品长期未使用，请从交流电插座断
开电源插头。
• 请勿在电源线上放置任何物品。
• 为了防止过热，必须始终为本产品提供适当的通风。
• 仅合格的 Christie 技师有权打开本产品的外壳。
• 所有程序均必须由合格的 Christie 技师完成。
触电危险。为避免受到人身伤害，在进行维护或维
修前，请始终断开所有电源连接。
高温表面危险。为避免受到人身伤害，在进行维护
或维修前，请按建议的冷却时间对投影机进行冷
却。
灼伤危险。为避免受到人身伤害，在进行维护或维
修前，请按建议的冷却时间对投影机进行冷却。
移动部件危险。为避免受到人身伤害，请勿用手触
摸，并将宽松衣物扎在身后。
风扇危险。为避免受到人身伤害，请勿用手触摸，
并将宽松衣物扎在身后。在进行维护或维修前，请
始终断开所有电源连接。
电压危险。为避免受到人身伤害，在进行维护或维
修操作前，请始终断开所有电源连接。
强光危险。为避免受到人身伤害，请永远不要直视
光源。
不适合家庭使用。
请参考维修手册。
在执行维护或维修操作前，请断开所有电源连接。
表示存在接地连接。
FDA 激光认证
(仅限美国地区投影机)
Christie Digital Systems Canada Inc.
809 Wellington Street North
Kitchener, ON N2G 4Y7
Canada
This product complies with performance standards for laser
products under 21 CFR Part 1040 except with respect to those
characteristics authorized by Variance Number 2016-V-1838
eective June 20, 2017.
U.S.A Only
强光危险。切勿直视镜头。极
高的亮度可能会导致永久性的
眼睛损伤。1类激光产品-根
据 IEC 60825-1:2014 和
IEC 62471-5:2015 危险等
级为3级。
切勿直视镜头。极高的亮度可能会导致
永久性的眼睛损伤。
警告！如果未能避免下列情况，则可能会导致死
亡或严重伤害。
当心！如果未能避免下列情况，则可能会导致轻
度伤害或中度伤害。
注意！如果未能避免下列情况，则可能导致设备
损坏或财产损失。
重要安全信息
8DWU1612-HS/DWU2022-HS 产品安全指南
020-001786-01 修订版 1 (03-2020)
Copyright ©2020 Christie Digital Systems USA Inc. 保留所有权利。
• 安装或移动产品时，请使用镜头塞。这能防止污染物进入
产品。
• 仅限使用由 Christie 推荐的清洁剂。所有其他清洁剂可能
造成产品损坏并导致保修无效。
安装安全和警告指南
• 连接至 IT 电力系统时会产生高泄漏电流。
• 触电和灼伤危险！靠近内部组件时，请小心谨慎。
• 只有合格的 Christie 技师可以受权使用工具箱中提供的工
具。
交流/电源的警示信息
• 火灾危险！请勿使用出现损坏的电源线。
• 火灾或电击危险！请勿使电源插座和延长电缆过载。
• 电击危险！仅限使用随产品提供的或由 Christie 推荐的交
流电源线。
• 火灾与电击危险！除非电源线、电源插座和电源插头都满
足相应的当地额定值标准，否则请勿尝试运行本系统。
• 电击危险！如果交流电源不在许可标签上指定的额定电压
和电流范围内，请勿尝试操作。
• 电击危险！交流电源线必须插入到接地保护的电源插座
中。
• 电击危险！在安装、移动、维修、清洁、取下组件或打开
任何外壳之前，请断开产品上的交流电源。
• 将产品安装在便于接触的交流电源插座附近。
激光安全预防措施
• 永久性/暂时性致盲危险！不允许直接暴露在光束中。1 类
激光产品 - 根据IEC 62471-5:2015危险等级为3 级。
• 本产品可能会散发出危险的光辐射。（危险等级 3）
• 激光辐射危险！本投影机具有内置的 4 类激光模块。不要
试图拆卸或修改激光模块。
• 用户手册中没有明确指示的任何操作或调整都会导致危险
的激光辐射泄露风险。
• 操作本产品之前必须保证所有机盖均已就位。
• 在光源开启的情况下，请勿直视镜头。极高的亮度可能会
导致永久性的眼睛损伤。
• 仅 Christie 合格技师有权对 Christie 激光投影系统进行组
装、安装和维修，因为他们了解使用激光以及本产品产生的
高电压和高温可能带来的危险。
亮度危险距离
此投影机可能会发出危险的光辐射和热辐射，根据 IEC 62471-
5:2015 标准分类为危害等级3。
• 永久性/暂时性致盲危险！不允许直接暴露在光束中。
• 永久性/暂时性致盲危险！操作员必须将对光束的接触控
制在危险距离内并将产品安装在可防止观察者眼睛在危险距
离内接触光束的高度。危险区域在地板以上的距离不得低于
3.0 米，到危险区域的水平间隙不得小于 2.5 米。
• 强光！请勿将反射体放置在产品光路下。
下图显示了眼睛和皮肤危险距离的区域：
• A-危险区域。激光照明投影机的投影光超过危险等级 2
的辐射极限的空间区域。在短暂或短促的接触后，亮度可能
会造成眼睛损伤（在人眼躲避光源之前）。光可能会造成皮
肤灼伤。
• B-危险距离。操作员必须将对光束的接触控制在危险距离
内，或将产品安装在可防止观察者眼睛在危险距离内接触光
束的位置。
• C-无接触区域。无接触区域的水平间隙必须至少为2.5米。
• D-到危险区域的垂直距离。危险区域在地板以上的距离不
得低于 3.0 米 。
• E-表示投影机的俯视图。
• F-表示投影机的侧视图。
关于每个镜头危险距离的详细信息，请参阅 DWU1612-HS/
DWU2022-HS
安装和设置指南
(P/N:020-001811-XX) 或
DWU1612-HS/DWU2022-HS
用户手册
(P/N: 020-001798
-XX)。
电源要求
了解 DWU1612-HS/DWU2022-HS 投影机的电源要求。
警告！如果未能避免下列情况，则可能会导致死
亡或严重伤害。
当心！如果未能避免下列情况，则可能会导致轻
度伤害或中度伤害。
警告！如果未能避免下列情况，则可能会导致死
亡或严重伤害。
警告！如果未能避免下列情况，则可能会导致死
亡或严重伤害。
警告！如果未能避免下列情况，则可能会导致死
亡或严重伤害。
参数 要求
额定功率
• DWU1612-HS:
200 - 240 VAC, 50/60
Hz, 7 A
• DWU2022-HS:
200 - 240 VAC, 50/60 Hz, 9 A
交流输入耦合器
C14
浪涌电流 最高 80 A @240 VAC
重要安全信息
9DWU1612-HS/DWU2022-HS 产品安全指南
020-001786-01 修订版 1 (03-2020)
Copyright ©2020 Christie Digital Systems USA Inc. 保留所有权利。
技术支持
• 北美洲和南美洲：+1-800-221-8025 或
Support.Americas@christiedigital.com
• 欧洲、中东和非洲：+44 (0) 1189 778111 或
Support.EMEA@christiedigital.com
• 亚太地区：+65 6877-8737 或
功耗
• DWU1612-HS:
最大 1410 W
• DWU2022-HS:
最大 1710 W
参数 要求
For the most current technical documentation, visit www.christiedigital.com.
Christie Digital Systems Canada Inc.
Kitchener
ph: 519 744 8005
Christie Digital Systems USA, Inc.
Cypress
ph: 714 236 8610
Corporate of¿ ces
United Kingdom
ph: +44 (0) 118 977 8000
United Arab Emirates
ph: +971 4 3206688
Spain
ph: +34 91 633 9990
Singapore
ph: +65 6877 8737
Republic of South Africa
ph: +27 (0)11 510 0094
Korea (Seoul)
ph: +82 2 702 1601
Japan (Tokyo)
ph: 81 3 3599 7481
India
ph: +91 (080) 6708 9999
Germany
ph: +49 2161 664540
France
ph: +33 (0) 1 41 21 44 04
Russian Federation
and Eastern Europe
ph: +36 (0) 1 47 48 100
China (Shanghai)
ph: +86 21 6278 7708
China (Beijing)
ph: +86 10 6561 0240
Brazil
ph: +55 (11) 2548 4753
Australia
ph: +61 (0) 7 3624 4888
Worldwide of¿ ces
Italy
ph: +39 (0) 2 9902 1161
Independant sales
consultant of¿ ces
Mexico
ph: +52 55 4744 1790
United States (New York)
ph: 646 779 2014
United States (Arizona)
ph: 602 943 5700
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Christie 科视DWU2022-HS Installation Information
- カテゴリー
- データプロジェクター
- タイプ
- Installation Information
他の言語で
- English: Christie 科视DWU2022-HS
関連論文
-
Christie 科视DWU2022-HS ユーザーマニュアル
-
-
Christie Roadie 4K40-RGB ユーザーマニュアル
-
-
-
Christie CP4325-RGB Installation Information
-
-
-
-