RayRun SDC25-B PLC Master Slave LED Driver ユーザーマニュアル
- タイプ
- ユーザーマニュアル
1. Power supply input
Connect to master driver’s 48Vdc output power, get
power and PLC commands from master. The power input
polarity is universal, and please connect each power pad to
master driver’s output.
2. LED output
Connect to constant current driving LED lights. The
output voltage range is from 0 to 48Vdc and the rated
output current is from 100-700mA. The rated output
current is programmable from the master driver. Please
make sure the voltage and current match the luminaire.
The SDC25-B can drive CCT or single color LED,
SDC25-E can drive single color only.
For CCT application, please connect LED’s common
positive to pad “+”, cool white to pad “CW-”and warm white
to pad “WW-”. For single color application, please connect
LED’s positive to pad “+” and negative to pad “SINGLE-”.
Model: SDC25-B/E
13.5mm
50mm
12
1
32
Introduction
Slave LED Driver
PLC Master-Slave
Power Line Communication
Ultra Compact
Full DC Dimming
3. Install steps
4 Automatic LED adaption
This driver verifies the LED character on each power
on. It will run a adaption process once the change of LED
is detected. During the adaption process, the lighting
fixture will dim up and down for about 10 seconds. After
this process, the driver will match the LED feature and
maintain a 0-100% full range physical non-flickering DC
dimming. Normally this adaption process happens on the
power on moment once LED is changed when the
brightness is higher than 30%.
For CCT application, each LED channel must has
same voltage and current feature for proper adaption and
working.
CAUTION: The adaption process CAN NOT detect the
value of LED rated current, so the rated current MUST be
set correctly from the master driver before connecting to
lighting fixture. Otherwise the lighting fixture can be
permanently damaged!
CCT / Single Color
This product is a slave LED driver to work with
specific master driver for LED lighting application. The
power input is DC 48V with power line communication
(PLC) commands and it can drive LED lights in voltage
range of 0-48V and rated current range of 100-700mA.
Besides dimming and color temperature adjusting,
the output current, fade time, current trim level, dimming
curve and group features are adjustable via the PLC
commands from master driver.
With the advanced full DC dimming scheme, the
connected luminaire will be flicker free from zero to
maximum brightness, and build premium lighting
experience.
Function & Size
1. Make sure the driver’s output current and voltage
range match the LED light.
2. Connect the output to LED light, make sure the
polarity is correct and cable is well insulated.
3. Connect the input to master driver’s output, make
sure the cable is well insulated.
CAUTION:
Do not connect ANY cable to AC power!
Only connect the input to compatible master driver!
+
cool
white
warm
white -
CCT Wiring
Single Color Wiring
Installation
+
Specification
Model
SDC25-B
SDC25-E
Function
2-in-1(Single color/CCT)
Single color
Inputvoltage
DC 48V
OutputVoltage
DC 0-46V
Outputcurrent
0-700mA
Maxoutputpower
25W
Communicationmode
Digital Power Line Communication
Outputcurrentsetting
100-700mA programmable＠1mA step
Fadetimesetting
0-25.5s with 0.1s step
Outputcurrenttrimming
100%-50% with 5% step
Dimmingcurvesetting
Linear, Logarithm, Optimized logarithm
Workingtemperature
-20°C~+70°C
Dimension
50x13.5x6mm
54
6. Output current trimming
Besides the output current setting, the output current
also can be trimmed from 100% to 50% of the rated
current at 5% step. With this feature, the LED current and
light luminance can be matched preciously. Please refer to
the master driver’s instruction for detailed operation.
7. ON/OFF fade time adjust
The on/off fade time can be adjusted in range of 0-
25.5s from the master driver. Please refer to the master
driver’s instruction for detailed operation.
The dimming curve can be changed from Logarithm,
Linear and Optimized logarithm. Please refer to the
master driver’s instruction for detailed operation.
8. Change dimming curve
The slave drivers connected to same master driver can
be programmed to different zones. User can adjust the
brightness or color temperature of each zone individually.
Please refer to the master driver’s instruction for detailed
operation.
9. Program the salve driver zone
Advanced features
5. Change rated output current
The output current can be set from the master driver
via smart app, the adjustable range of output current value
is 100-700mA. Please refer to the master driver’s
instruction for detailed operation.
SDC25-B/E
1
32
电源线载波通信
超小尺寸
纯直流调光
冷暖白/单色
可编程LED驱动从机
智能PLC主从驱动 简介
该LED驱动从机可以与对应的驱动主机构成智能
照明系统。本机电源输⼊为包含载波控制信号的直流
48V电源，本机输出可以驱动电压范围在0-48V、额定电
流在100-700mA的LED灯具。
本机能实现灯具的调光调⾊功能，⽽且还可以通过
驱动主机调节额定电流、渐变时间、电流微调、调光曲线
以及从机分组功能。
本机应⽤了先进的全DC调光技术，在从0到最⾼亮
度间都做到了完全⽆频闪，可实现极致的照明效果。
功能和尺⼨
1.电源输⼊
连接到驱动主机的48V直流输出，从驱动主机获取
电源和PLC控制指令。本机电源输⼊不分极性，请将两
个电源焊盘分别连接到主机的电源输出。
2.LED输出
连接到恒流驱动的LED灯具。本机输出的电压范围
为0-48V，额定电流范围为100-700mA，额定输出电流
可以通过驱动主机来设置。连接前请确保LED灯具的电
流电压范围与本机相符。
SDC25-B机型可以驱动单⾊或冷暖⽩LED，SDC25-
E仅⽤于单⾊LED。
对于冷暖⽩LED，请把焊盘“+”连接到LED的“+”端、
焊盘“CW-”连接到LED冷⽩端、焊盘“WW-”连接到
LED的暖⽩端。对于单⾊LED，请把焊盘“+”连接到LED
“+”端，焊盘“SINGLE-”连接到LED“-”端。
冷白
暖白
3.安装步骤
1.确认本机的输出电流与输出电压范围与LED灯具
相匹配。
2.将本机输出连接到LED灯具，确保极性正确、连接
良好且可靠绝缘。
3.将本机输⼊连接到驱动主机的输出端，并确保连
接良好且可靠绝缘。
请注意：
请勿将本机电缆连接到交流电！
本机仅在连接匹配的驱动主机时才能正常⼯作！
4.LED的⾃动适配
本机在每次通电且亮度⾼于约30%时都会检验
LED灯具的特性，当检测到灯具参数变化时，本机会
⾃动进⾏灯具适配以达到最佳的调光效果。在适配过
程中，灯具会明暗闪烁约10秒。适配完成后，驱动将完
全匹配灯具，并实现0-100%的DC恒流调光。
对于冷暖⽩灯具，请确保两个LED通道的电压和
电流特性相同，否则灯具⾃动适配将失败，驱动只能
在单⾊模式下⼯作。
注意！本机并不能识别LED的额定电流值，所以必
须先设定好输出电流值再连接灯具，否则可能会造成
LED的永久损坏！
安装和使⽤
13.5mm
50mm
12
+-
冷暖⽩接线
+
单⾊接线
型号
SDC25-B
SDC25-E
功能
2合1(单⾊/冷暖⽩)
单⾊
输⼊电压
DC48V
输出电压
DC0-46V
输出电流
0-700mA
最⼤输出功率
25W
通讯模式
数字化电源线载波通信
额定输出电流调节范围
100-700mA可调，步进1mA
渐变时间调节范围
0-25.5秒可调，步进0.1秒
输出电流微调
100%-50%,步进5%
调光曲线选择
线性、对数、优化对数
⼯作温度(Ta)
-20°C~+50°C
尺⼨
50x13.5x6mm
54
5.改变额定输出电流
本机的额定输出电流可以使⽤⼿机app通过驱动主
机进⾏设定，本机可设定的额定电流范围为100-
700mA。具体的设定⽅法请参考驱动主机的使⽤说明。
⾼级功能
6.输出电流微调
除了额定电流设定外，本机的输出电流还可以在
100%到50%之间进⾏微调。通过该功能，⽤⼾可以精确
匹配LED的驱动电流和亮度。具体的设定⽅法请参考驱
动主机的使⽤说明。
7.调节开关渐变时间
本机的开关灯渐变时间可以通过驱动主机在0到
25.5秒之间调节，具体的调节⽅法请参考驱动主机的使
⽤说明。
8.改变调光曲线
本机的调光曲线可以在线性、对数和优化对数曲线
中进⾏调节，具体的调节⽅法请参考驱动主机的使⽤说
明。
9.驱动从机的分组
连接到同⼀驱动主机的多个驱动从机可以分配到
不同的组，⽤⼾可以对不同的分组进⾏独⽴的亮度和⾊
温调节。具体的分组⽅法请参考驱动主机的使⽤说明。
产品规格
-
1
-
2
-
3
-
4
