KORG INC.
15-12, Shimotakaido 1-chome, Suginami-ku, Tokyo, Japan
Owner’s Manual
Warning
When installing, servicing, or replacing parts for this product, do not perform any
action that is not prescribed in the owner's manual.
Do not apply excessive force to the electronic components or connectors on the
circuit board, and do not disassemble it. Electrical shock, fire, or malfunction may
result.
Before installing this product, disconnect the power supply cable of the device in
which it is being installed, and disconnect any cables that connect peripheral
devices. Failure to do so may cause electrical shock or malfunctions.
Caution
Do not allow this product to become wet, and do not place objects on top of it.
Doing so will cause malfunctions.
Before touching this product, touch a metal part of the device into which it will be
installed, so that any static electricity in your body will be discharged. Failure to
do so will risk damaging the electronic components by static electricity.
When handling this product, be careful not to touch the leads (wires protruding
from the electronic components) on the rear side of the circuit board. Injury may
result.
When installing this product, do not touch any unrelated parts or circuit boards.
Electric shock or malfunction may result.
When installing this product, be careful not to cut yourself on any sharp edges or
parts of this product or of the device into which this product is being installed.
When installing this product, be careful not to drop screws etc. into the device
into which this product is being installed.
The manufacturer makes no warrantee regarding possible malfunctions or
damage that may result from improper use or modification. The manufacturer
also will take no responsibility for any damages that may result from loss or
disappearance of data.
Installing this product
For the procedure of installing this product, refer to the owner's manual of the
device into which the product is being installed. If you have any questions, please
contact your local Korg distributor.
Cautions when installing an option board
In order to install the board correctly, please pay attention to the following points.
Be careful of static electricity, which may damage components inside the product
or on the board. Before beginning the installation, touch an unpainted metal part
of the chassis or the grounding terminal of a grounded device to discharge any
static electricity that may be present in your body.
Perform the installation according to the steps given in the directions, making
sure that the board is installed correctly and in the correct orientation.
Verify that the option board has been installed correctly. If installation is incorrect,
faulty connections or a shorted power supply can cause malfunctions.
All the screws that are removed will be used, so be careful not to lose any.
Using screws of the incorrect shape or length can cause malfunctions or damage
to the product. Use only the screws that were included with the option board or
the screws that were fastened in the instrument.
When installing or removing the board, be careful not to drop parts or the option
board into the instrument.
Make sure that the attaching screws are tightened firmly, and are not loose.
Handle the board with care. Subjecting it to physical shock (by dropping or
pressing it) may cause damage or malfunctions.
Be careful not to touch any exposed metal portions of the circuit board, or any
parts that are not essential to the installation process.
THE FCC REGULATION WARNING (for U.S.A.)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Unauthorized changes or modification to this system can void the user’s
authority to operate this equipment.
CE mark for European Harmonized Standards
CE mark which is attached to our company’s products of AC mains operated
apparatus until December 31, 1996 means it conforms to EMC Directive (89/
336/EEC) and CE mark Directive (93/68/EEC).
And, CE mark which is attached after January 1, 1997 means it conforms to
EMC Directive (89/336/EEC), CE mark Directive (93/68/EEC) and Low
Voltage Directive (73/23/EEC).
Also, CE mark which is attached to our company’s products of Battery
operated apparatus means it conforms to EMC Directive (89/336/EEC) and
CE mark Directive (93/68/EEC).
IMPORTANT NOTICE TO CONSUMERS
This product has been manufactured according to strict specifications and
voltage requirements that are applicable in the country in which it is intended
that this product should be used. If you have purchased this product via the
internet, through mail order, and/or via a telephone sale, you must verify that
this product is intended to be used in the country in which you reside.
WARNING: Use of this product in any country other than that for which it is
intended could be dangerous and could invalidate the manufacturer's or
distributor's warranty.
Please also retain your receipt as proof of purchase otherwise your product
may be disqualified from the manufacturer's or distributor's warranty.
©
2003 KORG INC. 1506 GH
Printed in Japan
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may n ot cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Complies with Canadian ICES-003 Class B.
Conforme au Reglement Canadian NMB-003 classe B.
AIB-8
Introduction
Thank you for purchasing the Korg AIB-8 8-channel analog
input board. In order to enjoy long and trouble-free use, please
read this owner's manual carefully.
Features
By installing the AIB-8 in the D32XD/D16XD you can add
eight analog inputs.
INPUT 9...INPUT 16 jacks
Connect mic or line sources (such as keyboards) to these input
jacks. These are balanced inputs that allow you to use 1/4" TRS
phone jacks. You may also connect unbalanced phone plugs.
GND COLD HOT
GND HOT
Balanced phone plug Unbalanced phone plug
PAD keys
These drop the input level by 26 dB. The pad is on when the
switch is pressed in. You can extend the adjustable range of the
TRIM knob by switching this on when using line inputs.
Leave the pad switched off for low-output devices such as a
mic or guitar.
TRIM Knobs
These adjust the input level. The markings around the knob
indicate the input level.
Installation and settings
For details on installing and setting up the AIB-8, please refer
to the owner’s manual of the device into which you are install-
ing the AIB-8. If you have any questions, please contact your
local Korg distributor.
ACB-8
Introduction
Thank you for purchasing the Korg ACB-8 8-channel analog
compressor board. In order to enjoy long and trouble-free use,
please read this owner's manual carefully.
Features
Analog compressors allow you to apply dynamics processing
to adjust the level of the analog signal before it is converted
into digital data, preventing clipping before A/D conversion.
This also provides the distinctive character of analog compres-
sion that cannot be duplicated by a digital compressor.
The ACB-8 can also be installed on the 8-channel analog input
board (AIB-8: optional). If the AIB-8 and ACB-8 are installed,
you can use analog compressors on all sixteen channels of
analog input.
Installation and settings
For details on installing and setting up the ACB-8, please refer
to the owner’s manual of the device into which you are install-
ing the ACB-8. If you have any questions, please contact your
local Korg distributor.
DIB-8
Introduction
Thank you for purchasing the Korg AIB-8 ADAT I/O board . In
order to enjoy long and trouble-free use, please read this
owner's manual carefully.
Features
This board provides eight channels of ADAT input/output and
word clock input/output.
ADAT input/output supports 48 kHz/44.1 kHz sampling
frequencies and 24/16-bit depths.
1. ADAT inputs and outputs jack
This jack inputs and outputs an
ADAT format (ADAT Type I/II
format) digital signal of the same
sampling frequency and bit depth as
the current song.
2. Word clock inputs and outputs jack
This outputs the internal clock as a word clock signal.
This inputs a word clock signal from an external device.
To make connections, you will need to obtain an BNC coax
cable manufactured by the Alesis corporation or a video BNC
cable.
3. 75Ω switch
This switches the 75Ω word clock terminator on/off. Turn the
switch On if this is the end of the connection, or Off if the
connection is branched.
Installation and settings
For details on installing and setting up the DIB-8, please refer
to the owner’s manual of the device into which you are install-
ing the DIB-8. If you have any questions, please contact your
local Korg distributor.
*ADAT and Alesis are the trademarks or registered trademarks of Alesis Inc.
31
2
AIB-8
GND
COLD
HOT
GND HOT
ACB-8
DIB-8
31
2
-
1
-
2
-
3
-
4
