Startup Guide
入門指南
Sound Bar : HT-Z9F
4-727-534-71(1)
Continued on back page
續背面
© 2018 Sony Corporation Printed in Malaysia
Refer to the Operating Instructions
(separate document) for the TV connection
methods below.
What’s in the box
盒中內容
Bar Speaker (1)
主動式揚聲器系統（1）
Subwoofer (1)
主動式重低音揚聲器（1）
Remote control (1)
遙控器（1）
Grille frame (1)
網格（1）
HDMI cable (supports the
specification equal to Premium
High Speed HDMI cable with
Ethernet) (1)
HDMI連接線（支援規格等同支援
乙太網路連接的特級高速HDMI傳
輸線）（1）
R03 (size AAA) battery (2)
R03（AAA大小）電池（2）
WALL MOUNT TEMPLATE (1)
壁掛式安裝模板（1）
Wall mounting bracket (2),
Screw (2)
壁掛式支架（2）、螺絲（2）
Operating Instructions
使用說明書
Startup Guide (this document)
入門指南（本文件）
Installation position
安裝位置
Subwoofer
主動式重低音揚聲器
Bar Speaker
主動式揚聲器系統
Note
•Do not place magnetic cards on the system or near the system.
•Do not cover the top of the Bar Speaker with metal objects such as TV frame, etc. Wireless functions may
become unstable.
•Do not place metal objects around the system. Wireless functions may become unstable.
註
•請勿將磁卡放在系統上或系統附近。
•請勿在主動式揚聲器系統頂端覆蓋金屬物體，例如電視機架等。否則無線功能可能不穩定。
•請勿將金屬物體放在系統周圍。無線功能可能不穩定。
To mount the Bar Speaker on a wall
Refer to “Mounting the Bar Speaker or Rear Speaker on a Wall” in the Operating Instructions
(separate document).
若要將主動式揚聲器系統安裝在牆上
請參閱使用說明書（另外的文件）中的“在牆壁上安裝主動式揚聲器系統或後置揚聲器”。
1
Connecting with a TV and other devices
連接電視機和其他裝置
YES/是
Blu-ray Disc™ player,
cable box or satellite
box, etc.
Blu-ray Disc™播放
器、有線電視盒或衛
星電視盒等
: Video signal
: 視訊訊號
: Audio signal
: 音訊訊號
Blu-ray Disc player,
cable box or satellite
box, etc.
Blu-ray Disc播放
器、有線電視盒或衛
星電視盒等
: Video signal
: 視訊訊號
: Audio signal
: 音訊訊號
NO/否
Are there any HDMI IN jacks labeled “ARC” on your TV?
電視機是否有標示為“ARC”的HDMI IN插孔？
HDMI OUT
TV (ARC)
Use the HDMI cable (supplied) to connect an HDMI IN jack on your
TV and the HDMI OUT (TV (ARC)) jack on the Bar Speaker.
Note
•Make sure that the cable is firmly inserted.
•When your TV does not have an HDMI IN jack labeled “ARC,” you also
need to connect the TV and the Bar Speaker via an optical digital cable
(not supplied) as instructed in step . There will be no sound output
from the TV if the TV and the Bar Speaker are connected only via the
HDMI cable.
•To watch 4K video content, refer to “Connecting a 4K TV and 4K Devices”
in the Operating Instructions (separate document).
使用HDMI連接線（附帶）連接電視機的HDMI IN插孔與主動式揚聲器
系統的HDMI OUT (TV (ARC))插孔。
註
•確定連接線牢固地插入。
•如果您的電視機沒有標示為“ARC”的HDMI IN插孔，就必須透過步驟中所
示的光纖數位線（無附帶）連接電視機與主動式揚聲器系統。如果僅透過
HDMI連接線連接電視機與主動式揚聲器系統，電視機就沒有聲音輸出。
•若要觀看4K視訊內容，請參閱使用說明書（另外的文件）中的“連接4K電視
機和4K裝置”。
HDMI IN
1/2
Use an HDMI cable (not supplied) to connect an HDMI OUT jack
on a device and either the HDMI IN 1 jack or HDMI IN 2 jack on the
Bar Speaker.
Note
•Make sure that the cable is firmly inserted.
•To watch 4K video content, refer to “Connecting a 4K TV and 4K Devices”
in the Operating Instructions (separate document).
Tip
•When devices such as a Blu-ray Disc player, cable box, or satellite box are
currently connected to a TV, disconnect the device from the TV and then
connect it to the Bar Speaker to reproduce the high quality surround
sound.
使用HDMI連接線（無附帶）連接裝置的HDMI OUT插孔與主動式揚聲器
系統的HDMI IN 1插孔或HDMI IN 2插孔。
註
•確定連接線牢固地插入。
•若要觀看4K視訊內容，請參閱使用說明書（另外的文件）中的“連接4K電視
機和4K裝置”。
提示
•Blu-ray Disc播放器、有線電視盒或衛星電視盒等裝置目前已連接到電視機
時，將裝置與電視機斷開連接，然後將它連接到主動式揚聲器系統以重現高
品質環繞聲。
TV IN
(OPT)
When there is no HDMI jack labeled “ARC” on your TV, use an
optical digital cable (not supplied) to connect an optical out jack
on your TV and the TV IN (OPT) jack on the Bar Speaker.
Note
•Check the shape of the optical digital cable’s connecters and the jacks on
the TV and the Bar Speaker. Insert the connecters into the jacks in the
right directions. If you forcibly insert the connecters in the wrong
directions, the connecters and the jacks may be damaged.
如果您的電視機沒有標示為“ARC”的HDMI插孔，請使用光纖數位線
（無附帶）連接電視機的光纖輸出插孔與主動式揚聲器系統的TV IN
(OPT)插孔。
註
•請檢查光纖數位線連接器與電視機及主動式揚聲器系統插孔的形狀。以正確
的方向將連接器插入到插孔內。如果您以錯誤方向強力插入連接器，連接器
與插孔可能會損壞。
Connecting Sony TV with the BLUETOOTH Function
Wirelessly
Connecting a 4K TV and 4K Devices
Connecting a TV with an Analog Audio Cable
Startup Guide (this document) explains how to connect the Bar Speaker
and a TV via an HDMI cable.
請參閱使用說明書（另外的文件）以瞭解下列
電視機的連接方法。
無線連接具有BLUETOOTH功能的Sony電視機
連接4K電視機和4K裝置
使用類比音訊連接線連接電視機
入門指南（本文件）說明如何透過HDMI連接線，連接主動式揚聲器系統與電
視機。
2
Setting up the remote control
設定遙控器
3
Turning on the TV
開啟電視機的電源
Power ON
電源開啟
4
Turning on the system
開啟系統的電源
/
Power indicator
(green)
電源指示燈
（綠色）
Connect the AC power cords (mains leads) of the Bar Speaker and subwoofer
to the AC outlet (mains).
The remote control of the system does not work until “HELLO” in the front panel display
on the Bar Speaker disappears.
Press
(power) on the remote control of the system.
“TV” appears in the front panel display on the Bar Speaker.
Confirm that the power indicator of the subwoofer is lit in green.
If the power indicator of the subwoofer is lit in green, the connection with the Bar
Speaker is complete.
If not, refer to “Subwoofer” of “Troubleshooting” in the Operating Instructions (separate
document).
將主動式揚聲器系統和主動式重低音揚聲器的交流電源線連接到交流電插座。
在主動式揚聲器系統前顯示面板上的“HELLO”消失之前，系統的遙控器沒有作用。
按下系統遙控器上的
（電源）。
主動式揚聲器系統的前顯示面板上出現“TV”。
確認主動式重低音揚聲器的電源指示燈亮綠色。
如果主動式重低音揚聲器的電源指示燈亮綠色，表示主動式揚聲器系統的連接已完成。
否則，請參閱使用說明書（另外的文件）中“故障排除”的“主動式重低音揚聲器”。
5
Listening to sound
聆聽聲音
TV input switch
電視機輸入開關
TV
HDMI2
HDMI1
To listen to the audio of the TV
Select the desired input using the TV remote control.
The screen switches to the television broadcast screen and the TV audio is output from
the system.
If “TV” does not appear in the front panel on the Bar Speaker, press TV on the remote
control of the system to select the TV input. “TV” appears in the front panel display on
the Bar Speaker.
To listen to the audio of a device that is connected to the HDMI IN jack
on the Bar Speaker
Turn on the connected device. Then use the TV remote control to switch the
TV input to that for the HDMI IN jack to which the system is connected.
Press HDMI1 or HDMI2 on the remote control of the system depending on the
HDMI jack to which the device is connected.
“HDMI1” or “HDMI2” appears in the front panel display on the Bar Speaker and the audio
of the connected device is output from the system.
聆聽電視機的聲音
使用電視機遙控器選擇所要的輸入。
畫面切換為電視廣播畫面，而且系統輸出電視機的聲音。
如果主動式揚聲器系統的前顯示面板上沒有出現“TV”，請按下系統遙控器上的TV以選擇電
視機輸入。主動式揚聲器系統的前顯示面板上出現“TV”。
聆聽連接到主動式揚聲器系統HDMI IN插孔的裝置之音訊
開啟連接的裝置之電源。然後使用電視機遙控器將電視機輸入切換為系統連接的
HDMI IN插孔輸入。
根據連接裝置的HDMI插孔，按下系統遙控器上的HDMI1或HDMI2。
主動式揚聲器系統的前顯示面板上出現“HDMI1”或“HDMI2”，連接裝置的音訊會從系統輸
出。
Note
•Depending on the order in which you connect the TV and the system, the system may be
muted and “MUTING” may appear on the front panel display on the Bar Speaker. If this
happens, turn on the TV first, then the system.
註
•依據您連接電視機與系統的順序，系統可能會靜音，而且主動式揚聲器系統的前顯示面板上可
能會出現“MUTING”。如果發⽣這種狀況，請先開啟電視機，然後開啟系統。
6
Enjoying immersive surround experience
享受令人沈醉忘我的環繞體驗
+/–
VERTICAL S.
SW +/–
Press VERTICAL S. on the remote control of the system.
Enjoy movies, music, and more with sound that flows all around the room, surrounding
you from all directions.
Adjust the volume.
Adjust the volume of the Bar Speaker by pressing +/− on the remote control of the
system.
Adjust the volume of the subwoofer by pressing SW +/− on the remote control of the
system.
按下系統遙控器上的VERTICAL S.。
享受電影、音樂與更多，聲音從所有方向環繞您，在整個房間內流動。
調整音量。
按下系統遙控器上的 +/-，以調整主動式揚聲器系統的音量。
按下系統遙控器上的SW +/-，以調整主動式重低音揚聲器的音量。
Note
•The surround effects differ depending on a sound source.
註
•環繞效果因音源而異。
How to display the operation screen of the system on the TV
如何在電視機上顯示系統的操作畫面
Perform Easy Setup to display the system’s menu on the TV.
執行簡易設置，在電視機上顯示系統的選單。
Press HOME on the remote control of the system.
The Easy Setup screen is displayed on the TV screen.
If the Easy Setup screen does not appear, use the TV remote control to switch the TV input to that
for the HDMI IN jack to which the system is connected.
Select the language that you want for the system on-screen display.
Perform settings by following the on-screen instructions.
按下系統遙控器上的HOME。
電視機螢幕上顯示簡易設置畫面。
如果沒有顯示簡易設置畫面，請使用電視機遙控器將電視機輸入切換為系統連接的HDMI IN插孔輸入。
選擇您要的系統畫面顯示語言。
按照畫面上的指示進行設定。
Troubleshooting
故障排除
No TV sound is output from the system, or no picture is displayed on the
TV.
•Press TV on the remote control of the system to select the TV input. “TV” appears in the front panel display
on the Bar Speaker.
•Make sure that the input and output of the HDMI jacks on the system are correct.
•Disconnect the cables that are connected between the TV and the system, then connect them firmly again.
Disconnect the AC power cords of the TV and the system from the AC outlets (mains), then connect them
again.
•When the TV and the system are connected via an HDMI cable, enable the Control for HDMI function on the
TV. For details on the TV’s settings, refer to the operating instructions supplied with the TV. For more
information about the Control for HDMI function, refer to the Operating Instructions (separate document).
•Check the sound setting of the TV. When the TV is set to output the sound from the TV speakers, change
the setting to output the sound from the external speakers.
No picture or sound from the device connected to the system is output.
•Press one of the input buttons (TV, HDMI1, HDMI2, BLUETOOTH or ANALOG) on the remote control of the
system to select the desired input. The input type that corresponds with the selected input appears in the
front panel display on the Bar Speaker.
•Make sure that the input and output of the HDMI jacks on the system are correct.
•Disconnect the cables connected to the system, and then connect them again. Make sure that the cables
are firmly inserted.
The TV remote control does not work.
•When the Bar Speaker obstructs the remote control sensor of the TV, the TV remote control may not work.
In that case, set [IR-Repeater] to [On]. You can control the TV with the TV remote control. For details, refer to
“When the TV Remote Control does not Work” in the Operating Instructions (separate document).
No sound or only a very low-level sound is heard from the subwoofer.
•Press SW + on the remote control of the system to increase the volume of the subwoofer.
•Make sure that the power indicator on the subwoofer is lit in green. If the power indicator does not light up,
refer to “Subwoofer” of “Troubleshooting” in the Operating Instructions (separate document).
If the problem is not solved even though you have tried the measures above, refer to
“Troubleshooting” in the Operating Instructions (separate document).
系統沒有輸出電視機聲音，或是電視機沒有顯示圖像。
•按下系統遙控器的TV，以選擇電視機輸入。主動式揚聲器系統的前顯示面板上出現“TV”。
•確定系統上的HDMI插孔輸入和輸出正確。
•中斷連接電視機與系統之間的連接線，然後重新穩固連接它們。從交流電插座拔出電視機與系統的交流電源線，
然後重新連接它們。
•透過HDMI連接線連接電視機和系統時，在電視機上啟用HDMI控制功能。如需電視機設定的詳細資訊，請參閱電視
機附帶的使用說明書。如需HDMI控制功能的詳細資訊，請參閱使用說明書（另外的文件）。
•檢查電視機的聲音設定。電視機設定為從電視揚聲器輸出聲音時，請將設定變更為從外部揚聲器輸出聲音。
連接系統的裝置沒有輸出圖像或聲音。
•按下系統遙控器上的輸入按鈕（TV、HDMI1、HDMI2、BLUETOOTH或ANALOG），選擇所要的輸入。主動式揚聲器系
統的前顯示面板上出現對應所選輸入的輸入類型。
•確定系統上的HDMI插孔輸入和輸出正確。
•將連接系統的連接線拔出，然後重新連接。確定連接線牢固地插入。
電視機遙控器無效。
•當主動式揚聲器系統阻礙電視機的遙控感應器時，電視機遙控器可能無效。在此狀況下，請將[IR-Repeater]設
為[開]。您可用電視機遙控器控制電視機。如需詳細資訊，請參閱使用說明書（另外的文件）中的“電視機遙控
器不能操作時”。
主動式重低音揚聲器沒有發出聲音或聲音非常微弱。
•按下系統遙控器上的SW +提高主動式重低音揚聲器的音量。
•確認主動式重低音揚聲器的電源指示燈亮綠色。如果電源指示燈沒有亮起，請參閱使用說明書（另外的文件）
中“故障排除”的“主動式重低音揚聲器”。
如果嘗試以上措施後問題仍然沒有解決，請參閱使用說明書（另外的文件）中的“故障排除”。
-
1
-
2
