3D con vection fan
Instruction Manual
CF-1311
*
***www .origin.hk
*Read all instructions carefully before using the FAN, and keep this instruction for furture
reference when necessary.
***This instruction manual can be acquired at www.origin.hk.
Important Safety Information
1
Do not pull the power cord to disconnect
from power source. Always grasp the plug
to pull out.
Avoid using extension cord as it may
overheat and casue fire.
Before using the Fan, check if the
voltage marked on the rating label
corresponds to the mains at your
home.
220-240V~ 50Hz
Do not let children play parts of
package.
Open the package and ensure that the
Fan is undamaged. In case of doubt
do not use the FAN Cooler and contact
your supplier.
Use this Fan only as described in
this manual. Any other use not
recommended by the manufacturer
may casue fire, electrical shock or
injury to persons.
Read all instructions carefully before
using the Fan.
(
)
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
3D convection fan
Important Safety Information
2
The Fan is not intended for use in wet
or damp locations. Never locate the
Fan where it may fall into a bathtub or
other water container.
()
Keep the Fan clean to maintain in good
condition (refer to maintenance
section).
Do not place the
Fan
near a source
of heat or fire.
WARNING: To avoid danger of electric
shock, unplug from outlet when not
in use and before cleaning. If the
power cord is damaged, it must be
replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid hazard.
This Fan is intended for household
use ONLY and not for industrial
or outdoor use.
Do not leave the Fan unattended.
Always unplug the Fan Cooler when
not in use.
Do not insert any objects into the Fan
as it may cause an electric shock or
damage. Do not block or tamper with
the Fan in any manner while it is in
operation.
WARNING: The On/Off switch should
not be used as the sole means of
disconnecting power. Always unplug
the power cord before servicing or
moving the unit.
Always disconnected the Fan from the
power supply when moving it from
one location to another.
This product contains recyclable
materials. Do not dispose this
product as unsorted municipal
waste. Please contact your local
municipality for the nearest collection
Ensure that the fan is switched off from
the supply mains before removing the
guard.
3D convection fan
Main Parts
Air Oulet
Front Housing
Control Panel &
LED Indicator Light
LED
Remote Receiver
Handle
Air Inlet
3
Base
Power Cord
Plug
The picture is for reference only, everything in kind shall prevail.
3D convection fan
Function Setting
4
Hour
1 42 45 75 90
1.
1. Place the Fan on a stable and flat surface. Plug the Power Cord into an 220-240V~,
50Hz electrical outlet.
5. :
5. OSC(LEFT/RIGHT): Press the key to allow the Fan to LEFT/RIGHT oscillate the
wind direction. To stop the oscillation, press the key again.
220-240V~, 50Hz
3. : LED
(1)
3. SPEED: Adjust the Fan speed to the desired level: Low, Medium, or High
by pressing key. The speed setting is displayed on the LED light.
2.
2. POWER: Turn the Fan ON by pressing the key, the Fan start at low speed.
6. (TIMER) : 31
24
6. TIMER: Pressing the key to set desired auto power off time, There are 3 time
intervals (1, 2 or 4 hour) .
The Fan may be operated by the control panel (as shown in Figure 1) or by your
remote control.
4. : 3(45/75/90 )
( :
515)
4. OSC(UP/DOWN): Press the key to set desired angle (45/75/90 ), allow the Fan
to UP/DOWN oscillate the wind direction. (Remark: Before turning to selected up/
down angle, the fan outlet will turn upward to 90 firstly and stay for 5 to 15
seconds after switch on the fan.
1
Figure 1
POWER TIMER SPEED U/D OSC L/R OSC
The picture is for
reference only,
everything in
kind shall prevail.
3D convection fan
( )
:
: CF-1311
(3):
1.
/
2.
- /
- /
-
3.
4.
5.
6.
*** 3: 10315(
): w ww.origo.hk
403(12)21H
: 2156 8238
www.origo.hk
www.origo.hk
Warranty Card(1 year carry-in)
Item : 3D Convection Fan
Model : CF-1311
Service Centre
ORIGIN MARKETING LIMITED
Unit H, 21/F., Reason Group Tower (nearby 12 Wah Sing Street),
403 Castle Peak Road, Kwai Chung, N.T., Hong Kong.
Tel: 2156 8238
www.origo.hk
This product is warranted for 1year (commercial use for 3 months) from the date of purchase under
the following conditions:
1. For any defect, in the judgment of our technician, if it is caused under normal use, we are
responsible for repairing the product, and/or replacing parts at free of charge.
2. This warranty DOES NOT apply to:
- If the product has been damaged through abuse, misuse, negligence or accidents;
- Unauthorized repair, alteration/modification;
- The remote control, housing, cover or accessories.
3. The customer is requested to bring the unit to and from our Service Centre whenever
service is needed.
4. Any defective parts, which had been replaced, shall be of our property.
5. This warranty is valid in H.K.S.A.R. only.
6. Please show the Invoice to get free service.
***Extra 3 months warranty: just complete Online Warranty Registration within 10 days from the date
of receipt, free warranty will be extended to 15 months (not applicable to commercial use). Please
enter our website: www.origo.hk
www.origo.hk
3D convection fan
/
