EN
1
Operating instructions
Contents
Installation - Assistance, 2-3-4
Positioning and levelling
Connecting the water and electricity supplies
Advice regarding the first wash cycle
Technical data
Assistance
Electrical Connection
Description of the appliance, 5
Overall view
Control panel
Loading the racks, 6
Lower rack
Cutlery basket
Upper rack
Start-up and use, 7
Starting the dishwasher
Measuring out the detergent
Wash options
*
Wash cycles, 8
Table of wash cycles
Rinse aid and refined salt, 9
Measuring out the rinse aid
Measuring out the refined salt
Care and maintenance, 10
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Precautions and advice, 11
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 12
English,1
EN
LFT 216
DISHWASHER
AR
ZH
简体中文，25
15
،يبرع
EN
2
Installation - Assistance
Keep this instruction manual in a safe place for future
reference. If the appliance is sold, given away or moved,
please ensure the manual is kept with the machine, so that
the new owner may benefit from the advice contained within
it.
Please read this instruction manual carefully: it contains
important information regarding the safe installation, use and
maintenance of the appliance.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto
its back.
This appliance is intended to be used in household and
similar applications such as:
- staff kitchen areas in shops, offices and other working
environments;
- farm houses;
- by clients in hotels, motels and other residential type
environments;
- bed and breakfast type environments.
Positioning and levelling
1. Remove the appliance from all packaging and check that
it has not been damaged during transportation.
If it has been damaged, contact the retailer and do not
proceed any further with the installation process.
2. Check the dishwasher by placing it so that its sides or back
panel are in contact with the adjacent cabinets or even with
the wall. This appliance can also be recessed under a single
worktop
*
(see the Assembly instruction sheet).
3. Position the dishwasher on a level and sturdy floor. If
the floor is uneven, the front feet of the appliance may be
adjusted until it reaches a horizontal position. If the appliance
is levelled correctly, it will be more stable and much less likely
to move or cause vibrations and noise while it is operating.
4. Adjust the height of the rear foot from the front of the
appliance
* on the central lower part of the dishwasher, turning
a hexagonal spanner (red color) with an opening of 8 mm in a
clockwise direction to increase the height or in an anticlockwise
direction to decrease the height.
Connecting the water and electricity
supplies
Connection to the water and electricity supplies should
only be performed by a qualified technician.
The dishwasher should not stand on top of the water
hoses or the electricity supply cable.
The appliance must be connected to the water supply
network using new hoses.
Do not use old hoses.
The water inlet and outlet hoses and the electricity supply
cable may be positioned towards the right or the left in order
to achieve the best possible installation.
Connecting the water inlet hose
• Toasuitablecoldwaterconnectionpoint:beforeattaching
the hose, run the water until it is perfectly clear so that any
impurities that may be present in the water do not clog the
appliance; after performing this operation, screw the inlet
hose tightly onto a tap with a ¾ gas threaded connection.
• Toasuitablehotwaterconnectionpoint:yourdishwasher
may be supplied with hot water from the mains supply (if
you have a central heating system with radiators) provided
that it does not exceed a temperature of 60°C.
Screw the hose to the tap as described for connection to
a cold water supply.
If the inlet hose is not long enough, contact a specialist store
or an authorised technician
(see Assistance).
The water pressure must be within the values indicated in the
Technical data table
(see adjacent information).
The hose should not be bent or compressed.
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain duct
with a minimum diameter of 4 cm.
The outlet hose must be at a height ranging from 40 to 80
cm from the floor / surface where the dishwasher rests (A).
Before connecting the water outlet hose to the sink drain,
remove the plastic plug (B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water
supply in the event of anomalies or leaks from inside the
appliance.
Some models are also equipped with the supplementary
safety device
New Acqua Stop
*, which guarantees anti-
flooding protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose be cut
as it contains live electrical parts.
* Only available in selected models.
EN
3
Electrical connection
Before inserting the plug into the electrical socket, make
sure that:
• The socket is earthed and complies with current
regulations.
• The socket can withstand the maximum load of the
appliance, which is indicated on the data plate located
on the inside of the door
(see chapter entitled Description
of the appliance).
• Thepowersupplyvoltagefallswithinthevaluesindicated
on the data plate on the inside of the door.
• Thesocketiscompatiblewiththeplugoftheappliance.
If this is not the case, ask an authorised technician to
replace the plug
(see Assistance)
; do not use extension
cables or multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be re-
placed by the manufacturer or its Technical Assistance
Service in order to prevent all potential hazards. (See As-
sistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order
to protect it from any condensation which may form.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before
running the first wash cycle, completely fill the salt dispenser
with water and add only then approximately 1 kg of salt
(see chapter entitled Rinse aid and refined salt)
. The water
may overflow: this is normal and is not a cause for concern.
Select the water hardness value
(see chapter entitled Rinse
aid and refined salt)
. - After the salt has been poured into
the machine, the LOW SALT indicator light
* switches off.
If the salt container is not filled, the water softener and
the heating element may be damaged as a result.
* Only available in selected models.
Technical data
Dimensions
width 59.5 cm
height 82 cm
depth 57 cm
Capacity 12 standard place-settings
Water supply pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply voltage See appliance data plate
Total absorbed power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC (Labelling)
-2012/19/EC (WEEE)
Before contacting Assistance:
• Checkwhethertheproblemcanberesolvedusingthe
Troubleshooting guide
(see Troubleshooting).
• Restarttheprogrammetocheckwhethertheproblem
has ceased to exist.
• If the problem persists, contact the Authorised
Technical Assistance Service.
Never use the services of unauthorised technicians.
Please have the following information to hand:
• Thetypeofmalfunction.
• Theappliancemodel(Mod.).
• Theserialnumber(S/N).
This information can be found on the appliance data plate
(see Description of the appliance).
Assistance
EN
4
Electrical Connection
Electrical Connection
If your appliance is supplied with a 13 amp. fused plug it can
be plugged into a 13 amp socket for immediate use. Before
using the appliance please read the instruction below.
WARNING: THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse cover
re-fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colours as indicated by the coloured marking or the
colour that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
Removing the plug:
Ifyour appliance has a non-rewireable moulded plug and you
should wish to remove it to re-route the mains cable through
partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
- or:
- the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance
with BS 5733) which is accessible without moving
the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instruction for connecting cable to an altenative
plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow - Earth
Blue - Neutral
Brown - Live
CAUTION:
- Once the appliance has been installed, the electrical plug
and socket should remain accessible.
- The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or coloured Red.
Connect Blue wire to terminal marked “N” or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15 amp
fuse, either in the plug or adaptor or at the distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with
the following code:
BLUE “NEUTRAL” (“N”)
BROWN “LIVE” (“L”)
GREENANDYELLOW “EARTH” (“E”) or
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the plug
body and dispose of it as described above.
EN
5
Overall view
Description of the
appliance
1. Upper rack
2. Upper sprayer arm
3. Tip-up compartments
4. Rack height adjuster
5. Lower rack
6. Lower sprayer arm
7. Cutlery basket
8. Washing filter
9. Salt dispenser
10. Detergent and rinse aid dispensers
11. Data plate
12. Control Panel***
Control panel
ON/OFF/RESET
button
ON/OFF
indicator light
Low salt
indicator light
Select wash
cycle button
Low rinse aid
indicator light
Wash cycle indicator lights
***Only in completely built-in models.
* Only available in selected models.
The number and type of wash cycles and options may vary depending on the dishwasher model.
EN
6
Loading the racks
* Only available in selected models.
** The number and position may vary.
Before loading the racks, remove all food residue from
crockery and empty liquids from glasses and cups.
After loading the appliance, make sure that the sprayer arms
can rotate freely.
Lower rack and cutlery basket
The lower rack can hold pans, lids, plates, salad bowls, cutlery, etc.
Large plates and lids should ideally be placed at the sides of the rack.
Several dishwasher models are fitted with tip-up sections
*, which
can be used in a vertical position when arranging plates or in
a horizontal position when arranging saucepans, salad bowls
and frying pans.
The type of cutlery basket may vary (modular or non-modular)
according to the dishwasher model. The non-modular basket
must only be positioned at the front of the lower rack.
Both are fitted with grilles over the top, for improved cutlery
arrangement.
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards, or they
must be positioned horizontally in the tip-up compartments on
the upper rack.
Upper rack
Load this rack with delicate and lightweight crockery: glasses,
cups, saucers and shallow salad bowls.
Adjustable position tip-up compartments
The tip-up compartments
can be positioned at different
heights, to optimise the
arrangement of crockery
throughout the rack. Wine
glasses can be placed safely
in the tip-up compartments,
by inserting the stem of each
glass into the corresponding
slots.
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper rack
may be moved to a higher or lower level.
The height of the upper rack should ideally be adjusted
WHEN THE RACK IS EMPTY.
NEVER raise or lower the rack on one side only.
Open the left and right guide rail stops
and pull out the rack; position it higher or
lower as required, slide it along the guide
rails until the front wheels are in place and
close the stops
(see figure).
If the rack is fitted with Dual Space
handles
*
(see figure),
pull out the upper
rack until it reaches its stop point, grip the
handles at the sides of the rack and move
it upwards or downwards, then slowly let
it fall back into place.
Items that should not be washed in the dishwasher
• Woodenitems,objectswithwoodenorhornhandlesorglued-
on parts.
• Itemsmadefromaluminium,copper,brass,pewterortin.
• Itemsmadefromplasticmaterialwhichisnotheat-resistant.
• Antiqueorhand-paintedporcelain.
• Antique silver.Silver thatisnot antiquemay, however,be
washed in the dishwasher using a delicate wash cycle,
provided that it does not come into contact with other metals.
We recommend the use of crockery which is dishwasher
safe.
EN
7
Start-up and use
Measuring out the detergent
A good wash result also depends on the correct
amount of detergent being used; exceeding the stated
amount does not result in a more effective wash and
increases environmental pollution.
Only use detergent which has been specifically
designed for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle has
ended.
The use of tablets is only recommended for models
which offer the MULTI-FUNCTIONAL TABLETS option.
To achieve the best results from each washing and
drying cycle, powder detergent, rinse aid liquid and
salt should be used.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
1. Open cover C by pressing
button D.
2. Pour in the detergent after
consulting the
Table of wash
cycles:
• For powder detergent use
compartments A and B.
• For detergent in tablet form:
when the cycle requires 1 tablet,
place it in compartment A and close the cover; when it
requires 2, place the second tablet at the bottom of the
appliance.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.
A
B
D
C
* Only available in selected models.
Starting the dishwasher
1. Turn the water tap on.
2.OpenthedoorandpresstheON/OFFbutton:youwillhear
ashortbeepandtheON/OFFandwashcycleindicatorlights
switch on for a few seconds.
3. Measure out the detergent
(see below).
4. Load the racks
(see chapter entitled Loading the racks)
.
5. Select the wash cycle in accordance with the type of
crockery and its soil level
(see Table of wash cycles)
, by
pressing the P button; the indicator light corresponding to
the selected wash cycle will switch on.
7. Start the wash cycle by shutting the door: after a few
seconds have passed, a long beep signals the start of the
wash cycle.
8. Two short beeps and one long one indicate the end of the
wash cycle and the indicator light corresponding to the wash
cycle flashes slowly. Open the door, switch off the appliance
bypressingtheON/OFFbutton,shutoffthewatertapand
unplug the appliance from the electricity socket.
9. Wait for a few minutes before removing the crockery, in
order to avoid burns. Unload the racks, beginning with the
lower level.
- The machine will switch off automatically during
certain periods of inactivity, in order to minimise
electricity consumption.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection
process it is possible to change the cycle, provided that it
has only just begun: open the door, taking care to avoid the
escapingsteam,andpressandholdtheON/OFFbutton;the
machine will switch off with a long beep. Switch the machine
backonusingtheON/OFFbuttonandselectthenewwash
cycle using the P button; start the cycle by closing the door.
Adding extra crockery
Without switching off the machine, open the door, taking
care to avoid the escaping steam, and place the crockery
inside the dishwasher. Close the door: the cycle starts from
the point at which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a
power cut, the cycle stops. It starts again from the point at
which it was interrupted once the door has been shut or the
electricity supply is restored.
EN
8
Wash cycles
Wash cycle selection
instructions
Wash cycle
Detergent
(A) = compartment A
(B) = compartment B
Drying
Wash cycle duration
(tolerance ±10%)
Hrs. Min.
Powder Liquid Tablets
Extremely soiled dishes and pans
(not to be used for delicate items).
Intensive
30 g (A) 30 ml (A) 1 (A) Yes 2:25’
Normally soiled pans and dishes.
Standard daily wash cycle.
Normal
25 g (A)
5 g (B)
25 ml (A)
5 ml (B)
1 (A) Yes 1:50’
Preliminary wash cycle for
dishes while the load is awaiting
completion with the dishes from
the next meal.
Soak
No No No No 0:08’
Rinse and drying cycle for dishes
that are seldom used and are only
dusty
Special Guest
No No No Yes 0:32’
Economic and fast wash to be
used for lightly soiled dishes.
(Run cycle immediately after use)
(2 plates + 2 glasses + 4 pieces
of cutlery + 1 saucepan + 1 small
frying pan).
Rapid
25 g (A) 25 g (A) 1 (A) No 0:35’
Economic and fast wash for
delicate items which are sensitive
to high temperatures. (Run cycle
immediately after use) (glasses
upper rack + delicate plates, lower
rack).
Crystal
30 g (A) 30 g (A) 1 (A) Yes 1:30’
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher,
reduce the amount of detergent used accordingly.
The number and type of wash cycles and options may vary depending on the dishwasher model.
Notes:
Optimum performance levels when using the “”Rapid wash” cycle can be achieved by observing the maximum amounts of crockery
specified.
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 grams of powder = approximately 15 ml of liquid - 1 teaspoon = 5 grams of powder = approximately 5 ml of liquid
*TheEcowashcycleadherestotheregulationEN-50242.Althoughithasalongerdurationthanotherwashcyclesitusesless
energy and is les harmful to the environment.
Note for Test Laboratories:
forinformationrelatingtocomparativeENtestingconditions,pleasesendanemailtothefollowing
address:[email protected]
EN
9
Rinse aid and refined salt
Only use products which have been specifically
designed for dishwashers.
Do not use table salt or industrial salt, or washing
up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard.
Followtheinstructionsgivenonthepackaging.
If you do not add salt or rinse aid, the LOW SALT*
and LOW RINSE AID
* indicator lights remain lit.
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs
off surfaces more readily and therefore does not leave streaks
or marks.
The rinse aid dispenser should be filled:
•WhentheLOWRINSEAID* indicator light on the control
panel is illuminated;
1. Open the dispenser by turning the lid (G) in an anticlockwise
direction.
2. Pour in the rinse aid, making
sure it does not overflow from the
dispenser. If this happens, clean
the spill immediately with a dry
cloth.
3. Screw the lid back on.
NEVER pour the rinse aid directly
into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may adjust the quantity of rinse aid used. Use a screwdriver to
turnthedosageadjuster(F)tooneofthe6pre-setpositions
(the default position is set to 4):
•Iftherearestreaksonthecrockery,settheadjustmentdevice
to a lower number (1-3).
•Ifdropsofwaterremainonthecrockeryoriftherearelimescale
marks present after the cycle has finished, set the adjuster to
a higher number (4-6).
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the
water hardness level in your area. This information can be obtai-
ned from the organisation which supplies your household with
water.- Open the door and switch on the machine by pressing
theON/OFFbutton.
- Press the P button and hold for approximately 5 seconds; two
short beeps will sound and the indicator light corresponding to
the set degree of hardness will flash slowly on the control panel
(the water softening system is set to number 3).
- Press the P button repeatedly until the desired hardness level
has been reached
(1-2-3-4-5* see Water hardness table).
E.g. hardness 1 (indicator light 1 flashing)
hardness 2 (indicator light 1 illuminated, indicator light 2
flashing).
hardness 3 (indicator lights 1 and 2 illuminated, indicator light
3 flashing and so on).
- To exit the function, wait approximately few seconds or press
another option* button, or switch off the machine using the ON/
OFF button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
(°dH = hardness measured in German degrees - °f = hardness
measuredinFrenchdegrees-mmol/l=millimolesperlitre)
Measuring out the refined salt
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty. Refined salt
removes limescale from the water, thus avoiding the formation
of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
•Whenthegreenfloat* cannot be seen by simply looking at
the cap of the salt dispenser.
•WhentheLOWSALT* indicator light on the control panel is
illuminated;
1. Remove the lower rack and unscrew the
container cap (anticlockwise).
2. The first time you do this: fill the water tank
right up to its edge.
3. Position the funnel*
(see figure)
and fill
the salt container right up to its edge (this
should hold approximately 1 kg); it is not unusual for a little
water to leak out.
4. Remove the funnel
* and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it
on, the head facing downwards so as to let the water flow out of
the four cracks which are arranged in a star shape on the lower
part of the cap. (Salt cap with green float
*)
It is advisable to perform this procedure every time you add
salt to the container.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
When necessary, measure out the salt before a wash cycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
* Only available in selected models.
G
F
Water Hardness Table
Average salt container
capacity duration**
Level °dH °fH mmol/l months
1 0 - 6 0 - 10 0 - 1 7 months
2 6 - 11 11 - 20 1,1 - 2 5 months
3 12 - 17 21 - 30 2,1 - 3 3 months
4 17 - 34 31 - 60 3,1 - 6 2 months
5
*
34 - 50 61 - 90 6,1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the
use of salt
. * this setting may cause a slight increase in the
duration of the cycles. ** for 1 wash cycle per day.
EN
10
Care and maintenance
Shutting off the water and electricity
supplies
• Turn
off
the
water
tap
after
every
wash
cycle
to
avoid
leaks.
• Always
unplug
the
appliance
when
cleaning
it
and
when
performing maintenance work.
Cleaning the dishwasher
• The
external
surfaces
of
the
machine
and
the
control
panel may be cleaned using a non-abrasive cloth which
has been dampened with water. Do not use solvents or
abrasive products.
• Any
marks
on
the
inside
of
the
appliance
may
be
removed
using a cloth dampened with water and a little vinegar.
Preventing unpleasant odours
• Always
keep
the
door
of
the
appliance
ajar
in
order
to
avoid moisture from forming and being trapped inside
the machine.
• Clean
the
seals
around
the
door
and
detergent
dispensers
regularly using a damp sponge. This will avoid food
becoming trapped in the seals, which is the main cause
behind the formation of unpleasant odours.
Cleaning the sprayer arms
Food
residue
may
become
encrusted
ontothe
sprayer
arms
and block the holes used to spray the water. It is therefore
recommended that the arms are checked from time to time
and cleaned with a small non-metallic brush.
The two sprayer arms may both be removed.
To remove the upper sprayer
arm, rotate the locking ring in an
anti-clockwise direction.
The upper sprayer arm should
be replaced with the holes facing
upwards.
The lower sprayer arm can be
removed by pressing on the side
tabs and pulling it upwards.
Cleaning the water inlet filter*
If the water hoses are new or have not been used for an
extended period of time, let the water run to make sure it is
clear and free of impurities before performing the necessary
connections. If this precaution is not taken, the water inlet
could become blocked and damage the dishwasher.
Clean the water inlet filter at the tap outlet regularly.
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the filter
and clean it carefully under running water.
- Replace the filter and screw the water hose back into
position.
Cleaning the filters
The filter assembly consists of three filters which remove
food residues from the washing water and then recirculate
the water. They should be cleaned if you wish to achieve the
best results in every wash.
Clean the filters regularly.
The dishwasher should not be used without filters, or if
the filter is loose.
• After several washes, check the filter assembly and if
necessary clean it thoroughly under running water, using
a non-metallic brush and following the instructions below:
1. Turn the cylindrical filter C in an anti-clockwise direction
and pull it out (fig. 1).
2. Remove the cup filter B by exerting a slight pressure on
the side flaps (fig. 2).
3. Slide out the stainless steel plate filter A (fig. 3).
4. Inspect the trap and remove any food residue. NEVER
REMOVE the wash cycle pump
(black detail) (fig. 4).
After cleaning the filters, replace the filter assembly and fix
it in position correctly; this is essential for maintaining the
efficient operation of the dishwasher.
Leaving the machine unused for
extended periods
• Disconnecttheappliancefromtheelectricitysupply
and shut off the water tap.
• Leavethedooroftheapplianceajar.
•Whenyoureturn,runawashcyclewhenthedishwasher
is empty.
* Only available in selected models.
EN
11
Precautions and advice
This appliance was designed and manufactured in
compliance with current international safety standards. The
following information has been provided for safety reasons
and should therefore be read carefully.
General safety
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
•Childrenshouldbesupervisedtoensurethattheydonot
play with the appliance.
• Theappliancewasdesignedfordomesticuseinsidethe
home and is not intended for commercial or industrial use.
• The appliance must be used by adults only, to wash
domestic crockery in accordance with the instructions in
this manual.
• Theappliancemustnot be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
machine exposed to rain and storms.
• Donottouchtheappliancewhenbarefoot.
• Whenunpluggingtheappliancealwayspulltheplugfrom
the mains socket, do not pull on the cable.
• Thewatersupplytapmustbeshutoffandtheplugshould
be removed from the electrical socket before cleaning the
appliance or carrying out any maintenance work.
• If the appliance breaks down, do not under any
circumstances touch the internal parts in an attempt to
perform the repair work yourself.
• Nevertouchtheheatingelement.
• Donotleanorsitontheopendooroftheappliance:this
may cause the appliance to overturn.
• The door should not be left open as it may create a
dangerous obstacle.
• Keepdetergentandrinseaidoutofreachofchildren.
• Thepackagingmaterialshouldnotbeusedasatoy.
Disposal
• Disposalofpackagingmaterials:observelocallegislation
so that the packaging may be reused.
• The European Directive 2012/19/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the materials
inside the machine, while preventing potential damage
to the atmosphere and to public health. The crossed-out
dustbin is marked on all products to remind the owner of
their obligations regarding separated waste collection.
Forfurtherinformationrelatingtothecorrectdisposalof
household appliances, owners may contact the relevant
public authority or the local appliance dealer.
Saving energy and respecting the
environment
Saving water and energy
• Onlybeginawashcyclewhenthedishwasherisfull.While
waiting for the dishwasher to be filled, prevent unpleasant
odours using the Soak cycle
(see Wash cycles).
• Selectawashcyclewhichissuitedtothetypeofcrockery
and to the soil level of the crockery using the
Table of wash
cycles:
- For dishes with a normal soil level, use the Eco
wash cycle, which guarantees low energy and water
consumption levels.
- If the load is smaller than usual activate the Half load
option*
(see Start-up and use).
• Ifyourelectricitysupplycontractgivesdetailsofelectricity
saving time bands, run wash cycles during the periods
when a lower tariff is applied. The Delayed start
* button
(see Start-up and use)
helps you organise the wash cycles
accordingly.
Phosphate-free and chlorine-free detergents
containing enzymes
• Westronglyrecommendthatyouusedetergentsthatdo
not contain phosphates or chlorine, as these products are
harmful to the environment.
• Enzymes provide a particularly effective action at
temperatures around 50°C, and as a result detergents
containing enzymes can be used in conjunction with low-
temperature wash cycles in order to achieve the same
results as a normal 65°C wash cycle.
• Toavoidwastingdetergent,usetheproductinappropriate
quantities based on the manufacturer’s recommendations,
the hardness of the water and the soil level and quantity
of crockery to be washed. Even if they are biodegradable,
detergents contain substances which may alter the
balance of nature.
* Only available in selected models.
EN
12
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.
Problem: Possible causes / Solutions:
The dishwasher does not start or
cannot be controlled
• SwitchofftheappliancebypressingtheON/OFFbutton,switchitbackonafter
approximately one minute and reset the program.
• Theappliancehasnotbeenpluggedinproperly.
• Thedishwasherdoorhasnotbeenshutproperly.
The door won’t close • Thelockwasreleased.Stronglypushthedooruntila“clacking”noiseisheard.
No water drains out from the
dishwasher.
• Thedishwashercyclehasnotyetnished.
• Thewaterinlethoseisbent(see Installation).
• Thedrainductisblocked.
• Thelteriscloggedupwithfoodresidues.
The dishwasher makes excessive
noise.
• Thedishesarerattlingagainsteachotheroragainstthesprayerarms.
• Anexcessiveamountoffoamhasbeenproduced:thedetergenthasnotbeen
measured out correctly or it is not suitable for use in dishwashers (see Start-up and
use).
The dishes and glasses are
covered in a white lm or
limescale deposits.
• Theleveloftherenedsaltisloworthedosagesettingisnotsuitedtothehardnessof
the water (see Rinse aid and salt).
• Thelidonthesaltdispenserisnotclosedproperly.
• Therinseaidhasbeenuseduporthedosageistoolow.
The dishes and glasses are
streaked or have a bluish tinge.
• Therinseaiddosageistoohigh.
The crockery has not been dried
properly.
• Awashcyclewithoutadryingprogramhasbeenselected.
• Therinseaidhasbeenuseduporthedosageistoolow(see Rinse aid and salt).
• Therinseaiddispensersettingisnotsuitable.
• Thecrockeryismadefromnon-stickmaterialorplastic.
The dishes are not clean. • Theracksareoverloaded(seeLoadingtheracks).
• Thecrockeryhasnotbeenarrangedwell.
• Thesprayerarmscannotmovefreely.
• Thewashcycleistoogentle(see Wash cycles).
• Anexcessiveamountoffoamhasbeenproduced:thedetergenthasnotbeen
measured out correctly or it is not suitable for use in dishwashers (see Start-up and
use).
• Thelidontherinseaidcompartmenthasnotbeenshutcorrectly.
• Thelterisdirtyorblocked(seeCareandmaintenance).
• Therenedsaltlevelislow(seeRinseaidandsalt).
The dishwasher does not take any
water in - Tap shut-off alarm
(several short beeps
* are emitted)
(the 2 (Normal) and 3 (Soak) WASH
CYCLESindicatorlightsash).
• Thereisnowaterinthemainssupply.
• Thewaterinlethoseisbent(seeInstallation).
• Turnonthetapandtheappliancewillstartafterafewminutes.
• Theappliancelockhasbeenactivatedbecausenoactionwastakenwhenthebeeps*
sounded.
SwitchofftheapplianceusingtheON/OFFbutton,turnonthetapandswitchthe
appliance back on after 20 seconds by pressing the same button. Re-program the
appliance and restart the wash cycle.
Water inlet hose alarm / Water inlet
lter blocked
(the 1 (Intensive), the 2 (Normal)
and the 3 (Soak) WASH CYCLES
indicatorlightsash).
• SwitchofftheappliancebypressingtheON/OFFbutton.Shutoffthewatertapto
eliminatetheriskofoodingandremovetheplugfromtheelectricalsocket.
Makesurethewaterinletlterhasnotbecomeblockedbyimpurities(see“Careand
maintenance”chapter).
* Only available in selected models.
AR
13
16-15-14
17
18
19
20
21
22
23
24
25
LFT 216
13
AR
AR
14
1
2
( *
3
*4
8
60
4
40
80
A
B
New
*
Acqua Stop
*
AR
15
*
1
LOW SALT*
82
57
12
10 ÷ ÷
W 3
*
**
1615015135
1612015110
AR
16
13 13
. .
BS 1362 ASTA 13
.
.
.
.
:
BSI 13 -
.
: -
13 -
. )BS 5733 (
.
: :
-
-
:
”E“
.
. "L"
. "N"
. 13 )BS 1363( 13
15 15
.
.
:
)"N
L
E
.
ﺮﻔﺻﻷﺍﻭ ﺮﻀﺧﻷﺍ
ﻲﻨﺒﻟﺍ
ﻕﺭﺯﻷﺍ
ﺮﻴﺒﻣﺃ 13 ﺮﻬﺼﻣ
ﻚﻠﺴﻟﺍ ﺔﻜﺴﻣ
ﺔﻴﺿﺮﻌﻟﺍ
AR
17
.1
.2
.3
.4
.5
.6
.7
.8
.9
.10
.11
*** .12
***
*
*
*
AR
18
*
(
*
AR
19
A
B
1
D
2
BA
A
3
A
B
D
C
*
1
2
3
4
5
P
7
8
9
P
AR
20
55115151
*
)±10%
3030
A( 1
25
5
25
5
A( 1
(
+ 4 + 2 2
+ 1 + 1
2525A( 1
30 30A( 1
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
他の言語で
- English: Hotpoint LFT 216 A TW.R User guide
その他のドキュメント
-
Indesit LST 216 A CN ユーザーガイド
-
Whirlpool WFC 3C33 ユーザーガイド
-
Groupe Brandt DVH1044XC 取扱説明書
-
Electrolux ESI5550LAX ユーザーマニュアル
-
-
-
-
-
Electrolux ESL63010 ユーザーマニュアル
-