Keyboard Model No.：IRK71R
Dongle Model No.：DG011
Quick Installation Guide
K71R
Rechargeable Wireless
Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
CONTENTS
English
Quick Installation Guide ....................... 1-1
繁體中文 快速安裝手冊 ............................................... 2-1
1-1EN
Rechargeable Wireless Mechanical Keyboard
USB-C
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-2EN
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-3EN
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-4EN
Rechargeable Wireless Mechanical Keyboard
0
1
2
3
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-5EN
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-6EN
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-7EN
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-8EN
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-9EN
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-10EN
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-11EN
Rechargeable Wireless Mechanical Keyboard
1
2
Rechargeable Wireless Mechanical Keyboard
Package Contents
Keyboard x 1 USB Dongle x 1
USB-C Cable x 1 Quick Start Guide x 1
System Requirements
Compatible with: Windows® 7 , Windows® 8.1 and
Windows® 10 or later.
Available USB Port
Specifications
Keyboard
Dual Mode Interface:
Wired: USB ( Full Speed )
Wireless: 2.4GHz
Key number: 107 Keys
Smart Wheel: Included
Switch type: Mechanical Switch
Key stroke: 4.0 mm
N-Key rollover (NKRO)
Multimedia Hotkeys: 15 keys
Backlight Effect Hotkeys: 8 keys
Charging Interface: USB-C
Charging voltage/current: : DC5V/ 0.5 to 1A
Charging time: Approx 6~7 Hours (DC5V / 1A)
Battery Capacity: 3750 mAh
Weight: approx. 1.3 kg
Cable Length: approx. 180 cm
Dimension: 444 (L) X 155 (W) X 42 (H) mm
Receiver
Interface: USB
Dimension: 18.6 (L) X 14.5 (W) X 6.1 (H) mm
Hardware Installation
This keyboard has two connection modes: wired and wireless
You may find connection switch on the bottom of your keyboard
Switch ” R ” : Wireless Mode
Switch ” W ” : Wired Mode
Wired Installation:
1. Flip the connection switch to ” W ” for wired mode
2. Turn on your computer
3. Plug USB cable into an available USB port on your computer and
keyboard ( USB Type A for computer & Type C for keyboard )
4. Your computer will automatically detect the keyboard
5. You may use the keyboard after detection
Press FN+Ctrl+S to enable or disable Energy Saving Mode. When
the mode is enabled, backlight of your keyboard will automatically
be turned off after 5 minutes of keyboard inactivity and turned back
on after pressing any key. Energy Saving Mode in wired mode is
disabled by default.
Wireless Installation:
1. Flip the connection switch to ” R ” for wireless mode
2. Power on the computer and plug USB receiver into a USB port on
your computer
3. Turn on the power of keyboard and make sure battery has enough
power
4. Your computer will automatically detect the receiver and connect
with the keyboard
To set idle timeout for keyboard's Energy Saving Mode in RF
mode
“ “ + “ “ + “ “：Fully disable Energy Saving Mode
(Key 0 will blink 3 times when enabled)
“ “ + “ “ + “ “：1.5 minutes (default value, Key 1 will
blink 3 times when enabled)
“ “ + “ “ + “ “：5 minutes (Key 2 will blink 3 times
when enabled)
“ “ + “ “ + “ “：10 minutes (Key 3 will blink 3 times
when enabled)
Product Information
1. LED indication
: Num lock LED Indicator
: Caps lock LED Indicator
: Scroll lock LED Indicator
: Charging Indicator / Windows Lock Indicator (Red)
Blinking : Low Power
Static : Charging
Off : Fully Charged
PS1 : Backlight with only Esc key on: The keyboard is full key locked.
Press Fn+Esc to lock or unlock.
PS2 : All 4 indicators blinking: The keyboard is in Backlight
Customization Mode.
PS3 : when the low voltage indicator lighting, the backlit function
will be turned off automatically. The keyboard could be used
for 8 hours normally, please recharge during this period of time.
PS4 : Please turn off all the backlit function while charging, for
charging time saving.
2. Hotkeys
Press “ “ and desired function key simultaneously to use
hotkeys.
2.1 Setting key function
“ “ + “ “ + “ “：N-Key Rollover anti-ghosting
function ( default )
“ “ + “ “ + “ “：6-Key Rollover anti-ghosting &
standard USB settings
“ “ + “ “ + “ “：Factory reset
( Press and hold for 5 seconds )
2.2 Backlight Function Keys
Side Backlight
“ “ + “ “ + “ “ or “ “ : Select side backlight
colors
( depending on backlight effects )
“ “ + “ “ + “ “ or “ “：Adjust side backlight
speed
( depending on backlight effects )
“ “ + “ “：Turn side backlight on or off
“ “ + “ “：Switch between side backlight effects
( 7 types )
Keyboard Backlight
“ “ + “ “ or “ “：Adjust brightness ( 4 levels )
“ “ + “ “ or “ “ : Select or switch key backlight
colors
( depending on backlight effects )
“ “ + “ “ or “ “：Adjust backlight speed
( depending on backlight effects )
“ “ + “ “：Turn keyboard backlight on or off
“ “ + “ “：Light fadeout and tracing effects ( 5 types )
“ “ + “ “：Monochrome and breathing backlight
effects
“ “ + “ “：Backlight Customization Mode
Onboard memory can store up to five backlight customization
profile. Users may set backlight according to their preferences,
and profiles will be stored in 1 / 2 / 3 / 4 / 5 key respectively
after saving.
How to customize backlight:
A. Press“ “ + “ “：or (2/3/4/5) to select and switch to
lighting mode 1 ( 2/3/4/5)
B. Press“ “ + “ “ + “ “：simultaneously to activate
custom backlight setting
( 4 LED key indicators will start blinking )
C. Press desired key you want to configure, and the key will light
up; press“ “ + “ “ or “ “ to select colors for the key
D. Setting next key and color
E. Press the same illuminated key to cancel backlight setting for
the key
F. After configuration, press“ “ + “ “ + “ “ to save all
settings to current lighting mode and leave backlight
customization mode ( all 4 indicators will stop blinking )
G. Follow the same step A to F for setting 2/3/4/5 lighting mode
“ “ + “ “：RGB Backlight Effects – Set A ( 3 options )
“ “ + “ “：RGB Backlight Effects – Set B ( 7 options )
2.3 Multimedia & function key
“ “ + “ “：Show Desktop
“ “ + “ “：Lock PC
“ “ + “ “：Search for files or folders
“ “ + “ “：Launch Calculator
“ “ + “ “：Open my Computer
“ “ + “ “：Open E-Mail
“ “ + “ “：Open the internet browser
“ “ + “ “：Media player
“ “ + “ “：Play / pause
“ “ + “ “：Backward
“ “ + “ “：Stop play
“ “ + “ “：Forward
“ “ + “ “：Full key lock ( keyboard only lights up Esc
key when mode is in effect )
“ “ + “ “：Turn Windows lock on or off
2.4 Smart wheel function
Smart wheel is powered by Windows 10 protocol without
additional software, if you’re using the latest version of
Windows 10.
Smart Wheel is customizable and will automatically switch to your
preferred tool depending on software you’re using. Switch
between scrolling, zoom, rotation, brush tuning, video editing,
multimedia control and more. Smart Wheel support ranges from
Windows 10 built-in apps to pro software.
Press the below button to switch wheel mode
“ “：Wheel - volume control mode
Wheel clockwise: Increase volume
Wheel counterclockwise: Decrease Volume
Wheel button: Mute
“ “：Wheel - Task Switcher Mode
Wheel clockwise: Next Window
Wheel counterclockwise: Previous Window
Wheel button: Select
“ “：Wheel - Smart Wheel
Only works on PC with Windows 10
Go to Windows 10 Settings -> Devices -> Wheel for
customization
1-12EN
Rechargeable Wireless Mechanical Keyboard
3
1-13EN
Rechargeable Wireless Mechanical Keyboard
3. Software
The keyboard software is working under wired mode only;
however, saved keyboard settings will be applied under both
wired and wireless mode. Please go to iRocks official website to
download and install latest software for backlight, macro,
multimedia keys configuration and more.
1. Double click the installation software you download and follow
the instructions step by
2. Plug in the keyboard after installation, the software will start to
identify it
3. Launch the software. It will take some time to download the
memory parameter and setting of the keyboard
Attention: Connection switch (on the bottom of your keyboard )
must be flipped to ” W ” to use the software
1-14EN
Rechargeable Wireless Mechanical Keyboard
Troubleshooting & Cautions
If your wireless keyboard does not work normally:
Check if connection switch on the bottom of your keyboard is flipped
to ” R ” (2.4G wireless mode).
Check the USB receiver is connected to your computer’s USB port
correctly – unplug and plug it back.
Charge your keyboard immediately when the battery low indicator
lights up.
Metal objects close to or in between the keyboard may reduce
wireless performance. Try moving metal objects away from the
keyboard.
For saving power, the keyboard goes into sleep mode when it’s not
in use for a while. Press any key and wait for 1 to 3 seconds to bring
the keyboard out of sleep mode.
Charge the battery of your keyboard before storing it without use.
Storing your keyboard with low battery status and voltage for long
periods of time may cause battery malfunction.
When your keyboard is not in use, switching to USB wired mode
(connection switch W) is recommended.
Avoid putting your keyboard under high moisture condition or direct
sun.
Do not expose your keyboard to extreme temperatures, heat, fire or
liquid.
1-15EN
Rechargeable Wireless Mechanical Keyboard
Wireless ID Pairing
The wireless keyboard is pre-paired with included receiver before
shipment. It saves the need to pair and is ready to use out of the
box. When you need to re-pair your keyboard and receiver manually
to prevent signal interference or other issues, please follow the
steps below:
1. Flip the connection switch to ” R ” for 2.4G wireless mode and make
sure the keyboard is powered on.
2. Press and hold Fn + P for 3 seconds to enter pairing mode.
(P Key will flash)
3. Unplug and plug the USB receiver back into your computer’s USB
port.
4. Move the keyboard to close the USB receiver within 15cm, the ID
setting process will start automatically.
(It will take about 4~8 seconds)
5.Your keyboard should be ready to use
6. The above steps need to be completed within 1 minute, If the
keyboard doesn’t work properly, please remove the USB
receiver from computer’s USB port, then proceed to step 2~4
again.
2-1CH
Rechargeable Wireless Mechanical Keyboard
USB-C
Rechargeable Wireless Mechanical Keyboard
包裝內容
鍵盤 X 1 無線接收器 x 1 USB-C 連接線 x 1 快速安裝手冊 x 1
系統需求
微軟的視窗系統Windows® 7, Windows® 8.1 , Windows® 10
可用的USB傳輸埠
產品規格
鍵盤
產品名稱 : 無線鍵盤
產品型號 : IRK71R
雙模介面
有線 : USB ( Full speed )
無線 : 2.4GHz
按鍵數 : 107 鍵
智慧型按壓滾輪 : 1組
開關形式 : 機械開關
按鍵行程 : 4.0±0.5mm
全區防鬼鍵設計 (NKRO)
多媒體鍵 : 15 鍵
背光特效鍵 : 8 鍵
充電接口 : USB- Type C
充電電壓/電流 : DC5V/ 0.5 to 1A
充電時間 : 約 6~7 小時 (DC5V/1A充電電流)
可充式鋰電池容量 : 3750 mAh
產品重量 : 約 1.3 公斤
USB 線長 : 約 180 公分
產品尺寸 : 444 (L) X 155 (W) X 42 (H)mm
接收器
介 面: USB
產品型號 : DG011
產品尺寸 : 18.6 (L) X 14.5 (W) X 6.1 (H)mm
4. 安裝完成
在RF模式下，一段時間沒使用鍵盤，鍵盤會自動進入省電模式 (無線功
能進入低耗電休眠狀況及關閉鍵盤背光)，使用者可自行設定進入省電模
式的時間如下:
“ “ + “ “ + “ “：關閉省電模式 (0鍵閃3次)
“ “ + “ “ + “ “：約1.5 分鐘無動作時，啟動省電模式
( 內定值, 1鍵閃3次)
“ “ + “ “ + “ “：約5分鐘無動作時，啟動省電模式
(2鍵閃3次)
“ “ + “ “ + “ “：約10分鐘無動作時，啟動省電模式
(3鍵閃3次)
產品資訊
1. LED 指示燈
數字鎖指示燈
大小寫指示燈
滾動鎖指示燈
視窗鍵鎖及低電壓指示燈
閃爍 低電壓
恆亮 充電中
熄滅 充電完成
註一 : 單ESC背光鍵亮時, 表示全部按鍵在鎖鍵狀態( Fn+ESC )
註二 : 4個LED同時閃爍,表示進入按鍵背光自定義模式
註三 : 低電壓指示燈亮起時，背光功能將自動被關閉,鍵盤約仍
繼續正常使用約8小時,這段時間請進行充電。
註四 : 充電時建議將所有背光功能關閉，以便節省充電時間。
2.功能快捷鍵
同時按壓 “ “ 鍵跟下列按鍵產生對應的快捷功能
2.1 設定鍵
“ “ + “ “ + “ “：全區防衝突功能 (鍵盤內定值)
“ “ + “ “ + “ “：USB 標準規範六鍵輸出功能
“ “ + “ “ + “ “：長按5秒,可將按鍵所有功能
恢復出廠設定
2.2 背光功能快捷鍵
側背光功能
“ “ + “ “ + “ “ or “ “ : 選擇側背光顏色
( 依背光特效而定 )
“ “ + “ “ + “ “ or “ “：調整側背光特效變化速度
( 依背光特效而定 )
“ “ + “ “：側背光開啟跟關閉，ON / OFF
“ “ + “ “：側背光特效模式切換 ( 7 種特效 )
按鍵背光
“ “ + “ “ or “ “：調整按鍵背光明亮度 ( 四階 )
“ “ + “ “ or “ “ : 選擇按鍵背光顏色
( 依背光特效而定 )
“ “ + “ “ or “ “：調整按鍵背光特效變化速度
( 依背光特效而定 )
“ “ + “ “：按鍵背光開啟跟關閉，ON / OFF
“ “ + “ “：光跡追蹤 ( 5種效果切換 )
“ “ + “ “：單色恆亮及呼吸背光特效切換
“ “ + “ “：自訂背光模式
此功能提供5組使用者自訂背光功能，讓使用者依個人喜好，設定想
要的背光按鍵及顏色, 分別儲存於按鍵 1/2/3/4/5 中。
當按下FN+DEL一次後，會啟動第一組自訂背光，再按 FN+DEL一
次，切換下一組， 以此類推。
使用者也可直接按壓FN+1/2/3/4/5 直接叫出對應的自訂背光效果。
自訂背光設定方式：
A. 同時按壓“ “ + “ “ or (2/3/4/5) 選擇要修訂的自訂
背光模式 1 (2/3/4/5)
B. 同時按壓“ “ + “ “ + “ “啟動自訂背光錄製
( 4個指示燈快閃爍 )
C. 選擇按壓想要的背光亮起的按鍵，背光亮起，
按“ “ + “ “ or “ “選擇該鍵顏色
D. 繼續按壓其他要設定的按鍵，及選顏色
E. 按壓已亮起的背光按鍵，可再次取消該鍵背光
F. 完成設定，同時按壓“ “ + “ “ + “ “儲存設定,離開自
訂背光設定模式( 4個指示燈停止閃爍 )
G. 2/3/4/5自訂背光模式設定方式同步驟A到F
“ “ + “ “：背光特效A ( 共3組特效切換 )
“ “ + “ “：RGB背光特效B ( 共7 組特效切換 )
2.3 多媒體及功能快捷鍵
“ “ + “ “：顯示桌面
“ “ + “ “：鎖定電腦
“ “ + “ “：搜尋檔案或資料夾
“ “ + “ “：計算機
“ “ + “ “：我的電腦
“ “ + “ “：開啟Ｅ-Mail 軟體
“ “ + “ “：開啟網路瀏覽器
“ “ + “ “：多媒體呼叫
“ “ + “ “：播放/暫停
“ “ + “ “：回上一首
“ “ + “ “：停止
“ “ + “ “：回下一首
“ “ + “ “：開啟跟關閉全部鍵盤鎖鍵功能
( 所有背光功能熄滅，單單ESC鍵背光亮起 )
“ “ + “ “：開啟跟關閉鎖Windows/Application鍵
2.4 智慧旋鈕功能
智慧滾輪模式相容於Windows 10內建協定，只要您的電腦使用
Windows 10最新版本，皆可支援，無須任何額外驅動程式，從最簡單
的Windows 10 隨附應用程式，專業軟體皆能套用此功能。
智慧轉輪可依不同軟體自訂功能，並能根據軟體自動切換至對應的設
定。隨心切換，滾動瀏覽、縮放或旋轉、調整畫筆、影片剪輯及多媒
體播放等功能。
按壓下列按鍵進行旋鈕功能切換
“ “：滾輪音量調整模式
滾輪順時針: 調整音量大聲
滾輪逆時針: 調整音量小聲
按壓滾輪: 音量靜音
“ “：滾輪工作頁面選項模式
滾輪順時針: 向右移動工作頁面選項
滾輪逆時針: 向左移動工作頁面選項
按壓滾輪: 選取頁面
“ “：智慧轉輪功能 (如下圖)
1. 請至開始控制台裝置轉輪選項進行相關滾輪功能設
定
2. 將游標移置或切換到對應的軟體，常壓旋鈕叫出智慧轉
輪，選轉旋鈕選定所要的功能後按壓旋鈕選定。
(智慧轉輪功能項目會依對應的軟體及自行設定的不同，
自行切換對應的功能選項)
2-2CH
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
包裝內容
鍵盤 X 1 無線接收器 x 1 USB-C 連接線 x 1 快速安裝手冊 x 1
系統需求
微軟的視窗系統Windows® 7, Windows® 8.1 , Windows® 10
可用的USB傳輸埠
產品規格
鍵盤
產品名稱 : 無線鍵盤
產品型號 : IRK71R
雙模介面
有線 : USB ( Full speed )
無線 : 2.4GHz
按鍵數 : 107 鍵
智慧型按壓滾輪 : 1組
開關形式 : 機械開關
按鍵行程 : 4.0±0.5mm
全區防鬼鍵設計 (NKRO)
多媒體鍵 : 15 鍵
背光特效鍵 : 8 鍵
充電接口 : USB- Type C
充電電壓/電流 : DC5V/ 0.5 to 1A
充電時間 : 約 6~7 小時 (DC5V/1A充電電流)
可充式鋰電池容量 : 3750 mAh
產品重量 : 約 1.3 公斤
USB 線長 : 約 180 公分
產品尺寸 : 444 (L) X 155 (W) X 42 (H)mm
接收器
介 面: USB
產品型號 : DG011
產品尺寸 : 18.6 (L) X 14.5 (W) X 6.1 (H)mm
4. 安裝完成
在RF模式下，一段時間沒使用鍵盤，鍵盤會自動進入省電模式 (無線功
能進入低耗電休眠狀況及關閉鍵盤背光)，使用者可自行設定進入省電模
式的時間如下:
“ “ + “ “ + “ “：關閉省電模式 (0鍵閃3次)
“ “ + “ “ + “ “：約1.5 分鐘無動作時，啟動省電模式
( 內定值, 1鍵閃3次)
“ “ + “ “ + “ “：約5分鐘無動作時，啟動省電模式
(2鍵閃3次)
“ “ + “ “ + “ “：約10分鐘無動作時，啟動省電模式
(3鍵閃3次)
產品資訊
1. LED 指示燈
數字鎖指示燈
大小寫指示燈
滾動鎖指示燈
視窗鍵鎖及低電壓指示燈
閃爍 低電壓
恆亮 充電中
熄滅 充電完成
註一 : 單ESC背光鍵亮時, 表示全部按鍵在鎖鍵狀態( Fn+ESC )
註二 : 4個LED同時閃爍,表示進入按鍵背光自定義模式
註三 : 低電壓指示燈亮起時，背光功能將自動被關閉,鍵盤約仍
繼續正常使用約8小時,這段時間請進行充電。
註四 : 充電時建議將所有背光功能關閉，以便節省充電時間。
2.功能快捷鍵
同時按壓 “ “ 鍵跟下列按鍵產生對應的快捷功能
2.1 設定鍵
“ “ + “ “ + “ “：全區防衝突功能 (鍵盤內定值)
“ “ + “ “ + “ “：USB 標準規範六鍵輸出功能
“ “ + “ “ + “ “：長按5秒,可將按鍵所有功能
恢復出廠設定
2.2 背光功能快捷鍵
側背光功能
“ “ + “ “ + “ “ or “ “ : 選擇側背光顏色
( 依背光特效而定 )
“ “ + “ “ + “ “ or “ “：調整側背光特效變化速度
( 依背光特效而定 )
“ “ + “ “：側背光開啟跟關閉，ON / OFF
“ “ + “ “：側背光特效模式切換 ( 7 種特效 )
按鍵背光
“ “ + “ “ or “ “：調整按鍵背光明亮度 ( 四階 )
“ “ + “ “ or “ “ : 選擇按鍵背光顏色
( 依背光特效而定 )
“ “ + “ “ or “ “：調整按鍵背光特效變化速度
( 依背光特效而定 )
“ “ + “ “：按鍵背光開啟跟關閉，ON / OFF
“ “ + “ “：光跡追蹤 ( 5種效果切換 )
“ “ + “ “：單色恆亮及呼吸背光特效切換
“ “ + “ “：自訂背光模式
此功能提供5組使用者自訂背光功能，讓使用者依個人喜好，設定想
要的背光按鍵及顏色, 分別儲存於按鍵 1/2/3/4/5 中。
當按下FN+DEL一次後，會啟動第一組自訂背光，再按 FN+DEL一
次，切換下一組， 以此類推。
使用者也可直接按壓FN+1/2/3/4/5 直接叫出對應的自訂背光效果。
自訂背光設定方式：
A. 同時按壓“ “ + “ “ or (2/3/4/5) 選擇要修訂的自訂
背光模式 1 (2/3/4/5)
B. 同時按壓“ “ + “ “ + “ “啟動自訂背光錄製
( 4個指示燈快閃爍 )
C. 選擇按壓想要的背光亮起的按鍵，背光亮起，
按“ “ + “ “ or “ “選擇該鍵顏色
D. 繼續按壓其他要設定的按鍵，及選顏色
E. 按壓已亮起的背光按鍵，可再次取消該鍵背光
F. 完成設定，同時按壓“ “ + “ “ + “ “儲存設定,離開自
訂背光設定模式( 4個指示燈停止閃爍 )
G. 2/3/4/5自訂背光模式設定方式同步驟A到F
“ “ + “ “：背光特效A ( 共3組特效切換 )
“ “ + “ “：RGB背光特效B ( 共7 組特效切換 )
2.3 多媒體及功能快捷鍵
“ “ + “ “：顯示桌面
“ “ + “ “：鎖定電腦
“ “ + “ “：搜尋檔案或資料夾
“ “ + “ “：計算機
“ “ + “ “：我的電腦
“ “ + “ “：開啟Ｅ-Mail 軟體
“ “ + “ “：開啟網路瀏覽器
“ “ + “ “：多媒體呼叫
“ “ + “ “：播放/暫停
“ “ + “ “：回上一首
“ “ + “ “：停止
“ “ + “ “：回下一首
“ “ + “ “：開啟跟關閉全部鍵盤鎖鍵功能
( 所有背光功能熄滅，單單ESC鍵背光亮起 )
“ “ + “ “：開啟跟關閉鎖Windows/Application鍵
2.4 智慧旋鈕功能
智慧滾輪模式相容於Windows 10內建協定，只要您的電腦使用
Windows 10最新版本，皆可支援，無須任何額外驅動程式，從最簡單
的Windows 10 隨附應用程式，專業軟體皆能套用此功能。
智慧轉輪可依不同軟體自訂功能，並能根據軟體自動切換至對應的設
定。隨心切換，滾動瀏覽、縮放或旋轉、調整畫筆、影片剪輯及多媒
體播放等功能。
按壓下列按鍵進行旋鈕功能切換
“ “：滾輪音量調整模式
滾輪順時針: 調整音量大聲
滾輪逆時針: 調整音量小聲
按壓滾輪: 音量靜音
“ “：滾輪工作頁面選項模式
滾輪順時針: 向右移動工作頁面選項
滾輪逆時針: 向左移動工作頁面選項
按壓滾輪: 選取頁面
“ “：智慧轉輪功能 (如下圖)
1. 請至開始控制台裝置轉輪選項進行相關滾輪功能設
定
2. 將游標移置或切換到對應的軟體，常壓旋鈕叫出智慧轉
輪，選轉旋鈕選定所要的功能後按壓旋鈕選定。
(智慧轉輪功能項目會依對應的軟體及自行設定的不同，
自行切換對應的功能選項)
2-3CH
Rechargeable Wireless Mechanical Keyboard
Rechargeable Wireless Mechanical Keyboard
包裝內容
鍵盤 X 1 無線接收器 x 1 USB-C 連接線 x 1 快速安裝手冊 x 1
系統需求
微軟的視窗系統Windows® 7, Windows® 8.1 , Windows® 10
可用的USB傳輸埠
產品規格
鍵盤
產品名稱 : 無線鍵盤
產品型號 : IRK71R
雙模介面
有線 : USB ( Full speed )
無線 : 2.4GHz
按鍵數 : 107 鍵
智慧型按壓滾輪 : 1組
開關形式 : 機械開關
按鍵行程 : 4.0±0.5mm
全區防鬼鍵設計 (NKRO)
多媒體鍵 : 15 鍵
背光特效鍵 : 8 鍵
充電接口 : USB- Type C
充電電壓/電流 : DC5V/ 0.5 to 1A
充電時間 : 約 6~7 小時 (DC5V/1A充電電流)
可充式鋰電池容量 : 3750 mAh
產品重量 : 約 1.3 公斤
USB 線長 : 約 180 公分
產品尺寸 : 444 (L) X 155 (W) X 42 (H)mm
接收器
介 面: USB
產品型號 : DG011
產品尺寸 : 18.6 (L) X 14.5 (W) X 6.1 (H)mm
硬體安裝
此鍵盤提供有線跟2.4Ghz無線兩種介面，可透過下蓋底部的撥鈕進行介
面切換。
鍵盤背面開關切換到” W ”時為USB有線介面
鍵盤背面開關切換到” R ”時為2.4GHz無線介面
有線鍵盤安裝及說明:
1. 確認鍵盤下蓋撥鈕撥至” W ”位置
2. 開啟電腦電源
3. 將所附的USB傳輸線USB Type A接於電腦端，USB Type C 接於鍵盤端
4. 電腦會自動偵測到鍵盤裝置
5. 安裝完成
在有線模式下 FN+CTRL+S 可切換背光省電模式:
關閉鍵盤背光休眠模式 (預設 / 指示燈閃爍2次) : 背光恆亮
開啟鍵盤背光休眠模式 (指示燈閃爍3次) : 5分鐘無動作時，背光自動
關閉以節約能源，按任一鍵
喚醒
無線鍵盤安裝及說明:
1. 確認鍵盤下蓋撥鈕撥至” R ”位置, 確認鍵盤電力是否足夠
2. 開啟電腦電源，將無線接收器的USB接頭插入電腦的USB連接埠
3. 電腦會自動偵測到無線接收器並與鍵盤進行連接
4. 安裝完成
在RF模式下，一段時間沒使用鍵盤，鍵盤會自動進入省電模式 (無線功
能進入低耗電休眠狀況及關閉鍵盤背光)，使用者可自行設定進入省電模
式的時間如下:
“ “ + “ “ + “ “：關閉省電模式 (0鍵閃3次)
“ “ + “ “ + “ “：約1.5 分鐘無動作時，啟動省電模式
( 內定值, 1鍵閃3次)
“ “ + “ “ + “ “：約5分鐘無動作時，啟動省電模式
(2鍵閃3次)
“ “ + “ “ + “ “：約10分鐘無動作時，啟動省電模式
(3鍵閃3次)
產品資訊
1. LED 指示燈
數字鎖指示燈
大小寫指示燈
滾動鎖指示燈
視窗鍵鎖及低電壓指示燈
閃爍 低電壓
恆亮 充電中
熄滅 充電完成
註一 : 單ESC背光鍵亮時, 表示全部按鍵在鎖鍵狀態( Fn+ESC )
註二 : 4個LED同時閃爍,表示進入按鍵背光自定義模式
註三 : 低電壓指示燈亮起時，背光功能將自動被關閉,鍵盤約仍
繼續正常使用約8小時,這段時間請進行充電。
註四 : 充電時建議將所有背光功能關閉，以便節省充電時間。
2.功能快捷鍵
同時按壓 “ “ 鍵跟下列按鍵產生對應的快捷功能
2.1 設定鍵
“ “ + “ “ + “ “：全區防衝突功能 (鍵盤內定值)
“ “ + “ “ + “ “：USB 標準規範六鍵輸出功能
“ “ + “ “ + “ “：長按5秒,可將按鍵所有功能
恢復出廠設定
2.2 背光功能快捷鍵
側背光功能
“ “ + “ “ + “ “ or “ “ : 選擇側背光顏色
( 依背光特效而定 )
“ “ + “ “ + “ “ or “ “：調整側背光特效變化速度
( 依背光特效而定 )
“ “ + “ “：側背光開啟跟關閉，ON / OFF
“ “ + “ “：側背光特效模式切換 ( 7 種特效 )
按鍵背光
“ “ + “ “ or “ “：調整按鍵背光明亮度 ( 四階 )
“ “ + “ “ or “ “ : 選擇按鍵背光顏色
( 依背光特效而定 )
“ “ + “ “ or “ “：調整按鍵背光特效變化速度
( 依背光特效而定 )
“ “ + “ “：按鍵背光開啟跟關閉，ON / OFF
“ “ + “ “：光跡追蹤 ( 5種效果切換 )
“ “ + “ “：單色恆亮及呼吸背光特效切換
“ “ + “ “：自訂背光模式
此功能提供5組使用者自訂背光功能，讓使用者依個人喜好，設定想
要的背光按鍵及顏色, 分別儲存於按鍵 1/2/3/4/5 中。
當按下FN+DEL一次後，會啟動第一組自訂背光，再按 FN+DEL一
次，切換下一組， 以此類推。
使用者也可直接按壓FN+1/2/3/4/5 直接叫出對應的自訂背光效果。
自訂背光設定方式：
A. 同時按壓“ “ + “ “ or (2/3/4/5) 選擇要修訂的自訂
背光模式 1 (2/3/4/5)
B. 同時按壓“ “ + “ “ + “ “啟動自訂背光錄製
( 4個指示燈快閃爍 )
C. 選擇按壓想要的背光亮起的按鍵，背光亮起，
按“ “ + “ “ or “ “選擇該鍵顏色
D. 繼續按壓其他要設定的按鍵，及選顏色
E. 按壓已亮起的背光按鍵，可再次取消該鍵背光
F. 完成設定，同時按壓“ “ + “ “ + “ “儲存設定,離開自
訂背光設定模式( 4個指示燈停止閃爍 )
G. 2/3/4/5自訂背光模式設定方式同步驟A到F
“ “ + “ “：背光特效A ( 共3組特效切換 )
“ “ + “ “：RGB背光特效B ( 共7 組特效切換 )
2.3 多媒體及功能快捷鍵
“ “ + “ “：顯示桌面
“ “ + “ “：鎖定電腦
“ “ + “ “：搜尋檔案或資料夾
“ “ + “ “：計算機
“ “ + “ “：我的電腦
“ “ + “ “：開啟Ｅ-Mail 軟體
“ “ + “ “：開啟網路瀏覽器
“ “ + “ “：多媒體呼叫
“ “ + “ “：播放/暫停
“ “ + “ “：回上一首
“ “ + “ “：停止
“ “ + “ “：回下一首
“ “ + “ “：開啟跟關閉全部鍵盤鎖鍵功能
( 所有背光功能熄滅，單單ESC鍵背光亮起 )
“ “ + “ “：開啟跟關閉鎖Windows/Application鍵
2.4 智慧旋鈕功能
智慧滾輪模式相容於Windows 10內建協定，只要您的電腦使用
Windows 10最新版本，皆可支援，無須任何額外驅動程式，從最簡單
的Windows 10 隨附應用程式，專業軟體皆能套用此功能。
智慧轉輪可依不同軟體自訂功能，並能根據軟體自動切換至對應的設
定。隨心切換，滾動瀏覽、縮放或旋轉、調整畫筆、影片剪輯及多媒
體播放等功能。
按壓下列按鍵進行旋鈕功能切換
“ “：滾輪音量調整模式
滾輪順時針: 調整音量大聲
滾輪逆時針: 調整音量小聲
按壓滾輪: 音量靜音
“ “：滾輪工作頁面選項模式
滾輪順時針: 向右移動工作頁面選項
滾輪逆時針: 向左移動工作頁面選項
按壓滾輪: 選取頁面
“ “：智慧轉輪功能 (如下圖)
1. 請至開始控制台裝置轉輪選項進行相關滾輪功能設
定
2. 將游標移置或切換到對應的軟體，常壓旋鈕叫出智慧轉
輪，選轉旋鈕選定所要的功能後按壓旋鈕選定。
(智慧轉輪功能項目會依對應的軟體及自行設定的不同，
自行切換對應的功能選項)
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/
