Dell PowerEdge 6950 クイックスタートガイド

www.dell.com | support.dell.com

Dell™ PowerEdge™ 6950 Systems

Getting Started With

Your System

系统使用入门

はじめに

시스템시작하기

Model EMMA

www.dell.com | support.dell.com

Dell™ PowerEdge™ 6950 Systems

Getting Started With

Your System

Model EMMA

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

_________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerEdge, and Dell OpenManage are trademarks of Dell Inc.; AMD, AMD Opteron,

and combinations thereof are trademarks of Advanced Micro Devices, Inc.; Microsoft, Windows, and Windows Server are registered trademarks

of Microsoft Corporation; Red Hat is a registered trademark of Red Hat, Inc.; SUSE is a registered trademark of Novell, Inc. in the United

States and other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model EMMA

August 2006 P/N PM298 Rev. A00

Getting Started With Your System 3

System Features

The major hardware and software features of your system include:

• Two or four dual-core AMD Opteron™ 8000 Series processors.

• A minimum of 2 GB (dual-processor systems) or 4 GB (four-processor systems) of 667-MHz registered

DDR-II memory modules. Memory is upgradable to a maximum of 64 GB (four-processor systems)

by installing combinations of 512-MB, 1-GB, 2-GB, or 4-GB memory modules in the sixteen memory

module sockets on the system board. (128 GB of memory will be supported when 8 GB memory

modules are available.)

• Support for up to five 3.5-inch hot-plug SAS hard drives.

• An optional internal 1.44-MB, 3.5-inch diskette drive.

• An optional internal slim-line optical drive.

• An optional external USB diskette drive.

• An optional external USB optical drive.

• Two hot-pluggable, 1570-W power supplies in an 1 + 1 redundant configuration. The power supplies

support an input voltage range of 100 V to 208 V.

• Four hot-pluggable system cooling fans.

The system board includes the following features:

•

Two x8 lane-width PCI-Express (PCIe) expansion slots and six x4 lane-width PCIe slots.

(One x4 lane-width slot is occupied by the SAS controller card.) Four expansion slots (two x8 slots

and two x4 slots) support full-length expansion cards.

• Two integrated Gb Ethernet NICs, capable of supporting 10-Mbps, 100-Mbps, and 1000-Mbps data

rates. Each NIC also supports TCP/IP offload engine (TOE) functionality.

• Four USB 2.0-compliant connectors (two on the front panel and two on the back panel), capable

of supporting a diskette drive, an optical drive, a keyboard, a mouse, or a USB flash drive.

• Systems management circuitry that monitors operation of the system fans as well as critical system

voltages and temperatures. The systems management circuitry works in conjunction with the systems

management software.

• Standard Baseboard Management Controller (BMC) with serial access.

• An optional remote access controller (RAC) card for remote systems management.

•

An integrated VGA-compatible video subsystem based on an integrated

ATI RN50 33-MHz PCI

video controller. The video subsystem includes 16 MB of graphics memory and supports various 2D

graphics video modes. Maximum resolution is 1600x1280 with 65,536 colors. (

When the optional

RAC is installed, the integrated video subsystem is disabled and the video controller on the RAC is

used instead.)

4 Getting Started With Your System

• Front-panel support for a video connector, two USB connectors, and a 1x5 LCD panel for system ID

and error messaging.

• Back-panel connectors including one serial, one video, two USB, and two NIC connectors.

• System ID button on the front and back panels.

For more information about specific features, see "Technical Specifications" on page 8.

Supported Operating Systems

Your system supports the following operating systems:

• Microsoft

®

Windows Server

®

2003 R2 Standard and Enterprise Editions

• Microsoft Windows Server 2003 Standard and Enterprise x64 Editions

•Red Hat

®

Enterprise Linux AS for x86-64

•SUSE

®

Linux Enterprise Server 10 (when available)

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and regulatory information. Warranty

information may be included within this document or as a separate document.

• The

Rack Installation Guide

or

Rack Installation Instructions

included with your rack solution

describes how to install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system features and describes how to

troubleshoot the system and install or replace system components. This document may be found on

the CDs that came with your system or at

support.dell.com

.

• CDs included with your system provide documentation and tools for configuring and managing your

system.

• Updates are sometimes included with the system to describe changes to the system, software, and/or

documentation.

NOTE: Always check for updates on support.dell.com and read the updates first because they often

supersede information in other documents.

• Release notes or readme files may be included to provide last-minute updates to the system or

documentation or advanced technical reference material intended for experienced users or

technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not perform as expected, see

your Hardware Owner’s Manual.

Dell Enterprise Training and Certification is available; see www.dell.com/training for more information.

This service may not be offered in all locations.

Getting Started With Your System 5

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety instructions and important

regulatory information in your Product Information Guide.

This section describes the steps to set up your system for the first time.

Unpacking the System

Unpack your system and identify each item.(Your system may not include the optional rack kit

and bezel shown here.)

Keep all shipping materials in case you need them later.

6 Getting Started With Your System

Installing the System in a Rack

Install the system in the rack once you have read the "Safety Instructions" located in the rack

installation documentation for your system.

See your rack installation documentation for instructions on installing your system in a rack.

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to plug into each

connector. Be sure to tighten the screws (if any) on the monitor's cable connector.

NOTE: If you simultaneously connect two monitors to the system, using the front and rear video connections,

the video will default to the front since only one display can operate at a time.

Getting Started With Your System 7

Connecting the System and Monitor Power Cables

Connect the monitor's power cable to the monitor (optional). Connect the system’s power cables

to the system.

Plug the other end of the power cables into a grounded electrical outlet or a separate power source

such as an uninterrupted power supply (UPS) or a power distribution unit (PDU). If possible, connect

the power supplies to two different 110V power sources or two different 220V power sources,

depending on the power supplies used.

Turning on the System and Monitor

Press the power button on the system and the monitor (optional). The power indicators should light.

Adjust the monitor's controls until the displayed image is satisfactory.

If you have purchased the optional system bezel, install it after turning on the system.

8 Getting Started With Your System

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system documentation that ships

with your system. To install an operating system for the first time, see the Quick Installation Guide.

Be sure the operating system is installed before installing hardware or software not purchased with

the system.

Technical Specifications

Processor

Processor type Either two or four dual-core AMD Opteron™ 8000 Series

processors

Expansion Bus

Bus type PCIe

Expansion slots

Bandwidth

Two x8 lane-width

slots,

six x4 lane-width

slots

(One x4 slot is reserved for use by the SAS controller card)

Size

Two full-length and four half-length x4 lane-width slots

Two full-length x8 lane-width slots

Memory

Architecture 667-MHz registered DDR-II memory modules

Memory module sockets Sixteen 240-pin

Memory module capacities 512 MB, 1 GB, 2 GB, 4 GB, (8 GB when available)

Minimum RAM 2 GB (two processors) or 4 GB (four processors)

Maximum RAM 32 GB (two processors) or 64 GB (four processors)

(128 GB when 8 GB memory modules are available)

Drives

Hard drives Up to five 3.5-inch hot-plug SAS internal drives

Optical drive One optional slimline CD-ROM, DVD-ROM/CD-RW

combination, or DVD-ROM

NOTE: DVD devices are data only

Getting Started With Your System 9

Connectors

Back Panel

NIC

Two RJ-45 (for integrated 1-GB NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0 compliant

Video

15-pin VGA

Front Panel

Video

15-pin VGA

USB

Two 4-pin, USB 2.0 compliant

Video

Video type ATI RN50 video controller; VGA connector

Video memory 16 MB

Resolution Maximum 2D graphics resolution: 1600 x 1280,

65,536 colors

Power

AC power supply (per power supply)

Wattage

100-180VAC input: Output 12V/76.5A, 3.3Vsb/4A

Maximum 930W

180-264VAC input: Output 12V/129.5A, 3.3Vsb/5A

Maximum 1570W

Voltage

Input 100-240VAC, 12-8A, 47-63Hz

Heat dissipation

3171 BTU/hr (maximum)

Maximum inrush current

Under typical line conditions and over the entire system

ambient operating range, the inrush current may reach 55A

per power supply for 10 ms or less and 35A per power

supply for up to 150 ms.

Batteries

System battery

CR 2032 3.0-V lithium coin cell

10 Getting Started With Your System

Physical

Height 17.3 cm (6.8 in)

Width 44.7 cm (17.6 in)

Depth 70.1 cm (27.6 in)

Weight (maximum configuration) 37 kg (82 lb)

Environmental

NOTE: For additional information about environmental measurements for specific system configurations,

see www.dell.com/environmental_datasheets

Temperature

Operating

10° to 35°C (50° to 95°F)

Storage

–40° to 65°C (–40° to 149°F)

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum humidity

gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms (10 to 350 Hz)

Storage

1.54 Grms (10 to 250 Hz)

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse on each

side of the system) of 41 G for up to 2 ms

Storage

Six consecutively executed shock pulses in the positive and

negative x, y, and z axes (one pulse on each side of the

system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

Storage

–16 to 10,600 m (–50 to 35,000 ft)

www.dell.com | support.dell.com

Dell™ PowerEdge™ 6950 系统

系统使用入门

型号：

EMMA

注、注意和警告

注：注表示可以帮助您更好地使用计算机的重要信息。

注意：注意表示可能会损坏硬件或导致数据丢失，并告诉您如何避免此类问题。

警告：警告表示可能会导致财产损失、人身伤害甚至死亡。

_________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式进行复制。

本文中使用的商标：

Dell

、

DELL

徽标、

PowerEdge

和

Dell OpenManage

是

Dell Inc.

的商标；

AMD

、

AMD Opteron

及其组合是

Advanced Micro Devices, Inc.

的商标；

Microsoft

、

Windows

和

Windows Server

是

Microsoft Corporation

的注册商标；

Red Hat

是

Red Hat, Inc.

的注册商标；

SUSE

是

Novell, Inc.

在美国和其它国家

/

地区的注册商标。

本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。

Dell Inc.

对本公司的商标和产品名称之外

的其它商标和产品名称不拥有任何专有权。

型号：

EMMA

2006

年

8

月

P/N PM298

修订版

A00

系统使用入门 13

系统配置

系统的主要硬件和软件配置包括：

•

两个或四个双核心

AMD Opteron™ 8000

系列处理器。

•

至少

2 GB

（双处理器系统）或

4 GB

（四个处理器系统）的

667 MHz

带寄存器的

DDR-II

内存模

块。通过在系统板上的十六个内存模块插槽中安装

512 MB

、

1 GB

、

2 GB

或

4 GB

内存模块组合，

可将内存升级到最大

64 GB

（四个处理器系统）。（提供

8 GB

内存模块时，将支持

128 GB

内存。）

•

支持多达五个

3.5

英寸、热插拔

SAS

硬盘驱动器。

•

一个可选的内部

1.44 MB

、

3.5

英寸软盘驱动器。

•

一个可选的内部细长型光盘驱动器。

•

一个可选的外部

USB

软盘驱动器。

•

一个可选的外部

USB

光盘驱动器。

•

两个

1570 W

热插拔电源设备（

1 + 1

冗余配置）。这些电源设备支持的输入电压范围为

100 V

至

208 V

。

•

四个热插拔系统冷却风扇。

系统板包含以下配置：

• 两个

x8

信道宽度

PCI-Express (PCIe)

扩充槽和六个

x4

信道宽度

PCIe

插槽。（一个

x4

信道宽

度插槽由

SAS

控制器卡占用。）四个扩充槽（两个

x8

插槽和两个

x4

插槽）支持全长扩充卡。

•

两个集成的千兆位以太网

NIC

，可以支持

10 Mbps

、

100 Mbps

和

1000 Mbps

数据速率。每个

NIC

还支持

TCP/IP

卸载引擎

(TOE)

功能。

•

四个

USB 2.0

兼容连接器（两个在前面板，两个在背面板），可以支持软盘驱动器、光盘驱动器、

键盘、鼠标或

USB

快擦写驱动器。

•

系统管理电路，可监测系统风扇的运行以及系统临界电压和温度。系统管理电路需要与系统管理

软件配合工作。

•

标准底板管理控制器

(BMC)

，支持串行访问。

•

可选的远程访问控制器

(RAC)

卡，用于远程系统管理。

•

基于集成的

ATI RN50 33-MHz PCI

视频控制器的

VGA

兼容集成视频子系统。此视频子系统包

含

16 MB

的图形内存，并支持各种

2D

图形视频模式。最大分辨率为

1600 x 1280

（

65,536

色）。

（

如果安装了可选的

RAC

，集成视频子系统将被禁用，而使用

RAC

上的视频控制器。）

•

前面板支持视频连接器、两个

USB

连接器，

1x5 LCD

面板（用于显示系统

ID

和错误信息）。

•

背面板连接器包括一个串行连接器、一个视频连接器、两个

USB

连接器和两个

NIC

连接器。

•

系统

ID

按钮，位于前面板和背面板上。

有关特定配置的详细信息，请参阅第

18

页的“技术规格”。

14 系统使用入门

支持的操作系统

您的系统支持以下操作系统：

•

Microsoft

®

Windows Server

®

2003 R2

标准版和企业版

•

Microsoft Windows Server 2003

标准版和企业版（

64

位）

•

适用于

x86-64

的

Red Hat

®

Enterprise Linux AS

•

SUSE

®

Linux Enterprise Server 10

（可用时）

您可能需要的其它信息

警告：《产品信息指南》，提供了重要的安全信息和管制信息。保修信息可能包括在该说明文件中，

也可能作为单独的说明文件提供。

•

随机架解决方案附带的《机架安装指南》或《机架安装说明》，介绍了如何在机架中安装系统。

•

《硬件用户手册》提供了有关系统部件的信息，并介绍了如何排除系统故障以及如何安装或更换

系统组件。此说明文件可在随系统提供的

CD

中找到，或通过

support.dell.com

获得。

•

随系统附带的

CD

提供了用于配置和管理系统的说明文件和工具。

•

系统有时附带更新，用于说明对系统、软件和

/

或说明文件所做的更改。

注：请始终检查 support.dell.com 上的更新信息并首先进行阅读，因为该网站上的信息常常会取代其

它说明文件中的信息。

•

系统可能附带版本注释或自述文件，以提供系统或说明文件的最新更新内容，或者为有经验的用

户或技术人员提供高级技术参考资料。

获得技术帮助

如果您对本指南中的步骤有疑问，或系统运行无法达到预期效果，请参阅《硬件用户手册》。

Dell

可以提供企业培训与认证；有关详情，请访问

www.dell.com/training

。并非在所有国家和地区

均可提供此服务。

系统使用入门 15

安装和配置

警告：在执行以下过程之前，请阅读并遵循《产品信息指南》中的安全说明和重要的管制信息。

本节介绍初次安装系统时的步骤。

打开系统包装

打开系统包装并识别每项物品。（您的系统可能不包括此处显示的可选机架套件和挡板。）

妥善保管好所有运输包装材料，以备将来使用。

16 系统使用入门

将系统安装在机架中

在仔细阅读了系统的机架安装说明文件中的“安全说明”之后，在机架中安装系统。

有关在机架中安装系统的说明，请参阅机架安装说明文件。

连接键盘、鼠标和显示器

连接键盘、鼠标和显示器（可选）。

系统背面的连接器附有图标，这些图标指示了要插入每个连接器的电缆。确保拧紧显示器的电缆

连接器上的螺钉（如果有）。

注：如果使用前面和后面的视频连接器同时将两台显示器连接至系统，视频将默认使用前面的连接

器，因为一次仅能有一台显示器工作。

系统使用入门 17

连接系统和显示器电源电缆

将显示器的电源电缆连接到显示器（可选）。将系统的电源电缆连接至系统。

将电源电缆的另一端插入接地的电源插座或单独的电源，如不间断电源设备

(UPS)

或配电装置

(PDU)

。如果可能，将电源设备连接至两个不同的

110V

电源或两个不同的

220V

电源，具体取决

于所使用的电源设备。

打开系统和显示器

按下系统和显示器上的电源按钮（可选）。电源指示灯将会亮起。调节显示器的控制按钮直至获

得满意的显示图像。

如果您购买了可选的系统挡板，请在打开系统之后安装它。

18 系统使用入门

完成操作系统安装

如果您购买了预安装的操作系统，请参阅随系统提供的操作系统说明文件。如果您是初次安装操作

系统，请参阅《快速安装指南》。在安装非随系统购买的硬件或软件之前，请确保安装了操作系统。

技术规格

处理器

处理器类型两个或四个双核心

AMD Opteron™ 8000

系列处理器

扩充总线

总线类型

PCIe

扩充槽

带宽

两个

x8

信道宽度

插槽，

六个

x4

信道宽度

插槽

（一个

x4

插槽保留用于

SAS

控制器卡）

大小

两个全长和四个半长

x4

信道宽度插槽

两个全长

x8

信道宽度插槽

内存

体系结构

667 MHz

带寄存器的

DDR-II

内存模块

内存模块插槽十六个

240

针

内存模块容量

512 MB

、

1 GB

、

2 GB

、

4 GB

、（

8 GB

，如果有）

最小

RAM 2 GB

（两个处理器）或

4 GB

（四个处理器）

最大

RAM 32 GB

（两个处理器）或

64 GB

（四个处理器）

（提供

8 GB

内存模块时为

128 GB

）

驱动器

硬盘驱动器多达五个

3.5

英寸、热插拔

SAS

内部驱动器

光盘驱动器一个可选的细长型

CD-ROM

、

DVD-ROM/CD-RW

组合或

DVD-ROM

注：DVD 设备仅用于数据

ページを読み込んでいます...

Dell PowerEdge 6950 クイックスタートガイド

Dell PowerEdge 6950 クイックスタートガイド

他の言語で

関連論文