Dell PowerEdge T110 II クイックスタートガイド

Dell PowerEdge

T110 II Systems

Getting Started

With Your System

系统使用入门

開始使用系統

Memulai Dengan Sistem Anda

はじめに

시스템 시작 안내서

Dell PowerEdge

T110 II Systems

Getting Started

With Your System

Regulatory Model E11S Series

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better

use of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss

of data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.

Intel

®

and Xeon

®

are registered trademarks of Intel Corporation in the U.S. and other countries.

Microsoft

®

and Windows Server

®

are either trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries. Red Hat

®

and Red Hat

Enterprise Linux

®

are registered trademarks of Red Hat, Inc. in the United States and other countries.

VMware

®

is a registered trademark of VMWare, Inc. in the United States or other countries.

Citrix

®

and XenServer

®

are registered trademarks of Citrix Systems, Inc. in the United States and/or

other countries. SUSE ™

is a trademark of Novell, Inc. in the United States and other countries.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Model: E11S Series

December 2010 P/N DHY8H Rev. A01

Getting Started With Your System 3

Installation and Configuration

WARNING: Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Optional—Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

4 Getting Started With Your System

Connecting the Power Cable

Connect the system’s power cable to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor.

Securing the Power Cable

Bend the system power cable into a loop, as shown in the illustration,

and attach to the cable clasp.

Plug the other end of the power cable into a grounded electrical outlet or a

separate power source such as an uninterruptible power supply (UPS) or a

power distribution unit (PDU).

NOTE: Ensure that the system is connected to a stand-alone power source with

stable power supply for better performance.

Getting Started With Your System 5

Turning On the System

Press the power button on the system. The power indicator should light.

Complete the Operating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the installation and configuration documentation for your

operating system. Be sure the operating system is installed before installing

hardware or software not purchased with the system.

Supported Operating Systems

• Microsoft Windows Small Business Server 2011 (x64) Standard and

Essential Editions

• Microsoft Windows Server 2008 R2 SP1 (x64) Standard and

Foundation Editions

• Microsoft Windows Server 2008 R2 (x64) Standard and

Foundation Editions

• Microsoft Windows Server 2008 (x86) Standard Edition with SP2

• Microsoft Windows Server 2008 (x64) Standard Edition with SP2

• Microsoft Windows Server 2008 R2 SP1 (x64) with Hyper-V for

Standard Edition

6 Getting Started With Your System

• Microsoft Windows Server 2008 SP2 (x64) with Hyper-V for

Standard Edition

• Microsoft Windows Server 2008 R2 (x64) with Hyper-V for

Standard Edition

• Red Hat Enterprise Linux Server 6.0 (x64)

•SUSE

Linux Enterprise Server 11 SP1 (x64)

• VMware ESX Version 4.1 Update 1 (Classic)

• VMware ESXi Version 4.1 Update 1 (Embedded)

• Citrix XenServer v5.6 Feature Pack 1

NOTE: For the latest information on supported operating systems,

see support.dell.com.

Dell Software License Agreement

• Before using your system, please read the Dell Software License

Agreement that came with your system.

• You must consider any CD, DVD, or diskette set of Dell installed

software as BACKUP copies of the software installed on your

system’s hard-disk drive.

• If you do not accept the terms of the agreement, please call the customer

assistance telephone number. For customers in the United States,

call 800-WWW-DELL (800-999-3355). For customers outside the

United States, visit

support.dell.com

and select your country or region

from the top of the page.

Getting Started With Your System 7

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with

your system. Warranty information may be included within this document or

as a separate document.

• The

Owner’s Manual

provides information about system features

and describes how to troubleshoot the system and install or replace

system components. This document is available online at

support.dell.com/manuals

.

• Any media that ships with your system that provides documentation and tools

for configuring and managing your system, including those pertaining to the

operating system, system management, system updates, and system

components that you purchased with your system.

NOTE: Always check for updates on support.dell.com/manuals and read the

updates first because they often supersede information in other documents.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not

perform as expected, see your Owner’s Manual. Dell offers comprehensive

hardware training and certification. See dell.com/training for more information.

This service may not be offered in all locations.

Información de la NOM (sólo para México)

La información que se proporciona a continuación aparece en el dispositivo

descrito en este documento, en cumplimiento de los requisitos de la Norma

Oficial Mexicana (NOM):

Importador:

Número de modelo: E11S

Voltaje de alimentación: 100 V CA–240 V CA

Frecuencia: 50 Hz/60 Hz

Consumo eléctrico: 9.0 A–4.5 A

8 Getting Started With Your System

Technical Specifications

Processor

Processor type One Intel Xeon processor E3-1200 product family

or

One Intel Core i3-2100 product family

or

One Intel Pentium processor (when available)

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots Slot 1: PCIe x8 (x8 routing), half-length

Slot 2: PCIe x16 (x8 routing), full-length

Slot 3: PCIe x8 (x4 routing), half-length

Slot 4: PCIe x1 (x1 routing), half-length

Memory

Architecture 1066 MHz or 1333 MHz DDR3 unbuffered Error

Correcting Code (ECC) DIMMs

Memory module sockets Four 240-pin

Memory module capacities 1 GB, 2 GB, 4 GB, or 8 GB

Minimum RAM 1 GB

Maximum RAM 32 GB

Drives

Hard drives Up to four 3.5-inch, cabled SAS or SATA

internal drives

Optical drive Optional internal SATA DVD-ROM or

SATA DVD+/-RW

Optional external USB DVD-ROM

NOTE: DVD devices are data only.

Tape drive One optional internal half-height tape

backup device

Getting Started With Your System 9

Connectors

Back

NIC

One RJ-45 (for integrated 1 GB NIC)

Serial

9-pin, DTE, 16550-compatible

USB

Four 4-pin, USB 2.0-compliant

Video

15-pin VGA

eSATA

One 7-pin connector

Front

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

Two 4-pin, USB 2.0-compliant

Video

Video type Matrox G200, integrated in Winbond WPCM450

Video memory 8 MB

Power

AC power supply (per power supply)

Wattage

305 W

Voltage

100 VAC–240 VAC, 50 Hz/60 Hz, 9.0 A–4.5 A

Heat dissipation

1300 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 35 A per power supply for

10 ms or less.

Batteries

System battery

CR 2032 3.0-V lithium coin cell

10 Getting Started With Your System

Physical

Height 42.03 cm (16.55 in)

Width 18.90 cm (7.44 in)

Depth 46.38 cm (18.25 in)

Weight 16.1 kg (35.49 lb)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see dell.com/environmental_datasheets.

Temperature

Operating

10 °C to 35 °C (50 °F to 95 °F) with a maximum

temperature gradation of 10 °C per hour

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1 ºF/550 ft.

Storage

–40 °C to 65 °C (–40 °F to 149 °F) with

a maximum temperature gradation

of 20 °C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5 Hz–350 Hz for 15 min

Storage

1.87 Grms at 10 Hz–500 Hz for 15 min

Getting Started With Your System 11

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 31 G for 2.6 ms in

the operational orientation

Storage

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of 71 G for

up to 2 ms

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 32 G faired square

wave pulse with velocity change at

270 inches/second (686 centimeters/second)

Altitude

Operating

–16 m to 3048 m (–50 ft to 10,000 ft)

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1 ºF/550 ft.

Storage

–16 m to 10,600 m (–50 ft to 35,000 ft)

Airborne contaminant level

Class

G1 as defined by ISA-S71.04-1985

Environmental (continued)

12 Getting Started With Your System

Dell PowerEdge

T110 II 系统

系统使用入门

管制型号

E11S

系列

注、小心和警告

注：“注”表示可以帮助您更好地使用计算机的重要信息。

小心：“小心”表示如果不遵循说明，就有可能损坏硬件或导致数据

丢失。

警告：

“警告”表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本出版物中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式复制这些材料。

本文中使用的商标：

Dell

™

、

DELL

徽标和

PowerEdge

™

是

Dell Inc.

的商标。

Intel

®

和

Xeon

®

是

Intel Corporation

在美国

和其它国家

/

地区的注册商标。

Microsoft

®

和

Windows Server

®

是

Microsoft Corporation

在美国和

/

或其它国家

/

地区的商标或注册商标。

Red Hat

®

和

Red Hat

Enterprise Linux

®

是

Red Hat, Inc.

在美国和其它国家

/

地区的注册商标。

VMware

®

是

VMWare, Inc.

在美国或其它国家

/

地区的注册商标。

Citrix

®

和

XenServer

®

是

Citrix

Systems, Inc.

在美国和

/

或其它国家

/

地区的注册商标。

SUSE

™

是

Novell, Inc.

在美国和其它

国家

/

地区的商标。

本出版物中述及的其它商标和商品名称是指拥有相应商标和商品名称的公司或其产品。

Dell Inc.

对其它公司的商标和产品名称不拥有任何所有权。

管制型号：

E11S

系列

2010

年

12

月

P/N DHY8H Rev. A01

系统使用入门 15

安装和配置

警告：

执行下列步骤之前，请查看系统随附的安全说明。

打开系统包装

打开系统包装并检查各个组件。

可选

—

连接键盘、鼠标和显示器

连接键盘、鼠标和显示器（可选）。

系统背面的连接器附有图标，这些图标指示了要插入每个连接器的电缆。

确保拧紧显示器的电缆连接器上的螺钉（如果有）。

16 系统使用入门

连接电源电缆

将系统电源电缆连接至系统，如果使用显示器，将显示器电源电缆连接至显

示器。

固定电源电缆

如图例所示，将系统电源电缆弯曲成环状，并连接至电缆挂钩。

将电源电缆的另一端插入接地的电源插座或单独的电源，如不间断电源设备

(UPS)

或配电装置

(PDU)

。

注：为获得最佳的性能，请确保使用稳定的电源设备将系统连接至独立的

电源。

系统使用入门 17

开启系统

按下系统上的电源按钮。电源指示灯将会亮起。

完成操作系统安装

如果购买了预安装的操作系统，请参阅系统随附的操作系统说明文件。第一

次安装操作系统时，请参阅操作系统的安装和配置说明文件。请确保先安装

操作系统，然后再安装未随系统一起购买的硬件或软件。

支持的操作系统

•

Microsoft Windows Small Business Server 2011 (x64) Standard

版及

Essential

版

•

Microsoft Windows Server 2008 R2 SP1 (x64) Standard

版及

Foundation

版

•

Microsoft Windows Server 2008 R2 (x64) Standard

版及

Foundation

版

•

Microsoft Windows Server 2008 (x86) Standard

版（附带

SP2

）

•

Microsoft Windows Server 2008 (x64) Standard

版（附带

SP2

）

•

具有

Hyper-V

的

Microsoft Windows Server 2008 R2 SP1 (x64) Standard

版

•

具有

Hyper-V

的

Microsoft Windows Server 2008 SP2 (x64) Standard

版

•

具有

Hyper-V

的

Microsoft Windows Server 2008 R2 (x64) Standard

版

•

Red Hat Enterprise Linux Server 6.0 (x64)

18 系统使用入门

•

SUSE

Linux Enterprise Server 11 SP1 (x64)

•

VMware ESX

版本

4.1 Update 1

（经典）

•

VMware ESXi

版本

4.1 Update 1

（嵌入式）

•

Citrix XenServer v5.6 Feature Pack 1

注：有关支持的操作系统的最新信息，请访问 support.dell.com。

Dell

软件许可协议

•

在使用您的系统前，请阅读系统随附的

Dell

软件许可协议。

•

您必须将

Dell

安装的软件的任何

CD

、

DVD

或套装软盘视为您系统硬

盘驱动器上安装的软件的备份副本。

•

如果您不接受协议条款，请拨打客户帮助电话号码。美国地区的客

户，请致电

800-WWW-DELL (800-999-3355)

。美国以外的客户，请访

问

support.dell.com

并从页面顶部选择您的国家或地区。

ページを読み込んでいます...

Dell PowerEdge T110 II クイックスタートガイド

関連論文