Dell PowerEdge R210 II クイックスタートガイド

Dell PowerEdge

R210 II Systems

Getting Started

With Your System

系统使用入门

Memulai Dengan Sistem Anda

はじめに

시스템 시작 안내서

Dell PowerEdge

R210 II Systems

Getting Started

With Your System

Regulatory Model: E10S Series

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data

if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

___________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.

Intel

®

is a registered trademark and Core™ is a trademark of Intel Corporation in the U.S. and

other countries. Microsoft

®

and Windows Server

®

are either trademarks or registered trademarks

of Microsoft Corporation in the United States and/or other countries. Red Hat

®

and Red Hat Enterprise

Linux

®

and are registered trademarks of Red Hat, Inc. in the United States and/or other countries.

SUSE ™ is a trademark of Novell, Inc. in the United States and other countries. Citrix

®

and

XenServer

®

are either registered trademarks or trademarks of Citrix Systems, Inc. in the United States

and/or other countries. VMware

®

is a registered trademarks or trademark of VMWare, Inc. in the

United States or other countries.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Model E10S Series

December 2010 P/N 30G7N Rev. A00

Getting Started With Your System 3

Installation and Configuration

WARNING: Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Rails and System in a Rack

CAUTION: If installed in a closed or multi-unit rack assembly, the operating

ambient temperature of the rack environment may be greater than room ambient.

Therefore, consideration should be given to installing the equipment in an

environment compatible with the maximum ambient temperature (Tma) specified by

the manufacturer.

For more information, see

"Technical Specifications" on page 9.

Assemble the rails and install the system in the rack following the safety

instructions and the rack installation instructions provided with your system.

4 Getting Started With Your System

Optional—Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

Connecting the Power Cable

Connect the system’s power cable to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor.

Getting Started With Your System 5

Securing the Power Cable

Bend the system power cable as shown in the illustration and secure the cable

in the retention clip.

Plug the other end of the power cable into a grounded electrical outlet or

a separate power source such as an uninterrupted power supply (UPS) or

a power distribution unit (PDU).

Turning On the System

Press the power button on the system and the monitor. The power indicators

should light.

6 Getting Started With Your System

Installing the Optional Bezel

Install the bezel (optional).

Complete the Operating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the installation and configuration documentation for your

operating system. Be sure the operating system is installed before installing

hardware or software not purchased with the system.

Supported Operating Systems

• Microsoft Small Business Server 2011 Standard and Essential Editions

• Microsoft Windows Server 2008 R2 SP1 (x64) Web, Standard,

Foundation, and Enterprise Editions

• Microsoft Windows

Server 2008 R2 (x64) Web, Standard, Foundation,

and Enterprise Editions

• Microsoft Windows Server 2008 SP2 (x86) Web, Standard,

and Enterprise Editions

• Microsoft Windows Server 2008 SP2 (x64) Web, Standard,

and Enterprise Editions

• Microsoft Windows Server 2008 R2 SP1(x64) with Hyper-V for

Standard and Enterprise Editions

Getting Started With Your System 7

• Microsoft Windows Server 2008 R2 (x64) with Hyper-V for Standard and

Enterprise Editions

• Microsoft Windows Server 2008 SP2 (x64) with Hyper-V for Standard and

Enterprise Editions

• VMware ESX 4.1 Update 1 (Classic)

• VMware ESX 4.1 Update 1 (Embedded)

• Citrix XenServer 5.6 Feature Pack 1

• Red Hat Enterprise Linux

6.0 (x86_64)

• SUSE Linux Enterprise Server 11 SP1 (x86_64)

NOTE: For the latest information on supported operating systems,

see support.dell.com.

Dell Software License Agreement

• Before using your system, please read the Dell Software License

Agreement that came with your system.

• You must consider any CD, DVD, or diskette set of Dell installed

software as BACKUP copies of the software installed on your system's

hard-disk drive.

• If you do not accept the terms of the agreement, please call the customer

assistance telephone number. For customers in the United States,

call 800-WWW-DELL (800-999-3355). For customers outside the

United States, visit

support.dell.com

and select your country or region

from the top of the page.

8 Getting Started With Your System

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with

your system. Warranty information may be included within this document

or as a separate document.

• The rack documentation included with your rack solution describes how

to install your system into a rack.

•The

Owner’s Manual

provides information about system features

and describes how to troubleshoot the system and install or replace

system components. This document is available online at

support.dell.com/manuals

.

• Any media that ships with your system that provides documentation and

tools for configuring and managing your system, including those pertaining

to the operating system, system management software, system updates,

and system components that you purchased with your system.

NOTE: Always check for updates on support.dell.com/manuals and read the

updates first because they often supersede information in other documents.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does

not perform as expected, see your Owner’s Manual. Dell offers

comprehensive hardware training and certification. See dell.com/training

for more information. This service may not be offered in all locations.

Getting Started With Your System 9

Información de la NOM (sólo para México)

La información que se proporciona a continuación aparece en el dispositivo

descrito en este documento, en cumplimiento de los requisitos de la Norma

Oficial Mexicana (NOM):

Technical Specifications

Importador:

Número de modelo: E10S

Voltaje de alimentación: 100 V CA-240 V CA

Frecuencia: 50 – 60 Hz

Consumo eléctrico: 4,0 - 2,0 A

Processor

Processor type One Intel Core processor i3-2100 product family

or

One Intel Xeon processor E3-1200 product family

or

One Intel Pentium processor (when available)

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots One full-height, half-length x16 link

Memory

Architecture 1066 MHz and 1333 MHz DDR3 unbuffered

Error Correcting Code (ECC) DIMMs

Memory module sockets Four 240-pin

Memory module capacities 1 GB, 2 GB, 4 GB, or 8 GB

Minimum RAM 1 GB

Maximum RAM 32 GB

10 Getting Started With Your System

Drives

Hard drives Up to two 3.5-inch cabled SAS or SATA

internal drives

or

Up to two 2.5-inch cabled SAS or SATA

internal drives

Optical drive One optional internal SATA DVD-ROM or

DVD+/-RW drive

NOTE: DVD devices are data only.

Optional external USB DVD-ROM

Connectors

Back

NIC

Two RJ-45 (for integrated 1 GB NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

eSATA

One 7-pin connector

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

Two 4-pin, USB 2.0-compliant

Video

Video type Matrox G200, integrated in Winbond WPCM450

Video memory 8 MB

Getting Started With Your System 11

Power

AC power supply (per power supply)

Wattage

250 W

Voltage

100 VAC–240 VAC, 50 Hz/60 Hz, 4.0 A–2.0 A

Heat dissipation

1040 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 25 A

Batteries

System battery

CR 2032 3.0-V lithium coin cell

Physical

Height 4.24 cm (1.67 inches)

Width 43.4 cm (17.09 inches)

Depth 39.37 cm (15.5 inches)

Weight

(maximum configuration)

8.058 kg (17.77 lb)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see dell.com/environmental_datasheets.

Temperature

Operating

10 °C to 35 °C (50 °F to 95 °F) with a maximum

temperature gradation of 10 °C per hour

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1 ºF/550 ft.

Storage

–40 °C to 65 °C (–40 °F to 149°F) with a

maximum temperature gradation of 20 °C

per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

12 Getting Started With Your System

Maximum vibration

Operating

0.26 Grms at 5 Hz–350 Hz for 15 min

Storage

1.87 Grms at 10 Hz–500 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 31 G for 2.6 ms in

the operational orientation

Storage

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of 71 G for

up to 2 ms

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 32 G faired

square wave pulse with velocity change at

270 inches/second (686 centimeters/second)

Altitude

Operating

–16 m to 3048 m (–50 ft to 10,000 ft)

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1 ºF/550 ft.

Storage

–16 m to 10,600 m (–50 ft to 35,000 ft)

Airborne Contaminant Level

Class

G1 as defined by ISA-S71.04-1985

Environmental (continued)

Dell PowerEdge

R210 II 系统

系统使用入门

管制型号：

E10S

系列

注、小心和警告

注：“注”表示可以帮助您更好地使用计算机的重要信息。

小心：“小心”表示如果不遵循说明，就有可能损坏硬件或导致数据

丢失。

警告：

“警告”表示可能会造成财产损失、人身伤害甚至死亡。

___________________

本出版物中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式复制这些材料。

本文中使用的商标：

Dell

™

、

DELL

™

徽标和

PowerEdge

™

是

Dell Inc.

的商标。

Intel

®

和

Core

™

分别是

Intel Corporation

在美国

和其它国家

/

地区的注册商标和商标。

Microsoft

®

和

Windows Server

®

是

Microsoft Corporation

在美国和

/

或其它国家

/

地区的商标或注册商标。

Red Hat

®

和

Red Hat Enterprise Linux

®

是

Red Hat, Inc.

在美国和

/

或其它国家

/

地区的注册

商标。

SUSE

™

是

Novell Inc.

在美国和其它国家

/

地区的商标。

Citrix

®

和

XenServer

®

是

Citrix

Systems, Inc.

在美国和

/

或其它国家

/

地区的注册商标或商标。

VMware

®

是

VMware, Inc.

在美国或其它国家

/

地区的注册商标。

本出版物中述及的其它商标和商品名称是指拥有相应商标和商品名称的公司或其产品。

Dell Inc.

对其它公司的商标和产品名称不拥有任何所有权。

管制型号

E10S

系列

2010

年

12

月

P/N 30G7N Rev. A00

系统使用入门 15

安装和配置

警告：

执行下列步骤之前，请查看系统随附的安全说明。

打开系统包装

打开系统包装并检查各个组件。

在机架中安装滑轨和系统

小心：如果安装在封闭的或多单元机架部件中，机架周围的操作环境温度可

能高于室温。所以，应当考虑将设备安装在与制造商指定的最高环境温度

(TMA)

兼容的环境中。

有关详情，请参阅

第

21

页的“技术规格”。

遵循系统随附的安全说明和机架安装说明，在机架中组装滑轨并安装系统。

16 系统使用入门

可选

—

连接键盘、鼠标和显示器

连接键盘、鼠标和显示器（可选）。

系统背面的连接器附有图标，这些图标指示了要插入每个连接器的电缆。

确保拧紧显示器的电缆连接器上的螺钉（如果有）。

连接电源电缆

将系统电源电缆连接至系统，如果使用显示器，将显示器电源电缆连接至显

示器。

系统使用入门 17

固定电源电缆

如图所示，将系统电源电缆弯曲图中的形状，并使用固定夹固定好电缆。

将电源电缆的另一端插入接地的电源插座或单独的电源，如不间断电源设备

(UPS)

或配电装置

(PDU)

。

开启系统

按下系统和显示器的电源按钮。电源指示灯将会亮起。

18 系统使用入门

安装可选挡板

安装挡板（可选）。

完成操作系统安装

如果购买了预安装的操作系统，请参阅系统随附的操作系统说明文件。第一

次安装操作系统时，请参阅操作系统的安装和配置说明文件。请确保先安装

操作系统，然后再安装未随系统一起购买的硬件或软件。

支持的操作系统

•

Microsoft Small Business Server 2011 Standard

版及

Essential

版

•

Microsoft Windows Server 2008 R2 SP1 (x64) Web

、

Standard

、

Foundation

版及

Enterprise

版

•

Microsoft Windows

Server 2008 R2 (x64) Web

、

Standard

、

Foundation

版及

Enterprise

版

•

Microsoft Windows Server 2008 SP2 (x86) Web

、

Standard

版

及

Enterprise

版

•

Microsoft Windows Server 2008 SP2 (x64) Web

、

Standard

版

及

Enterprise

版

•

具有

Hyper-V

的

Microsoft Windows Server 2008 R2 SP1 (x64)

Standard

版及

Enterprise

版

•

具有

Hyper-V

的

Microsoft Windows Server 2008 R2 (x64) Standard

版及

Enterprise

版

ページが読み込まれています...

Dell PowerEdge R210 II クイックスタートガイド

Dell PowerEdge R210 II クイックスタートガイド

他の言語で

関連論文