DeWalt DCG405 ユーザーマニュアル

DCG405

Final page size: A5 (148mm x 210mm)

B

Copyright DeWALT

English 3

简体中文 20

繁體中文 35

한국어

49

1

Fig. A

Fig. B

90˚

4

5

8

11 10

3

7

2 1

10

11

6

9

A9 KR

A9 only

2

Fig. E

Fig. C

5

14

13

12

9

5

Fig. F

18

17

16

7

19

6

4

Fig. D

15

Fig. G

8

19

20

TW B1 IN

ENGLISH

3

Congratulations!

You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the

most reliable partners for professional power toolusers.

Technical Data

English (original instructions)

CORDLESS SMALL ANGLE GRINDER

DCG405

DCG405-IN DCG405-B1/TW DCG405-A9 DCG405-KR

Voltage V

DC

18 18(20 Max) 18(20 Max) 18(20 Max)

Battery type

Li-Ion Li-Ion Li-Ion Li-Ion

Power output W 800 800 800 800

No-load/rated speed min

-1

9000 9000 9000 9000

Wheel diameter mm 100 100 125 125

Wheel thickness (max) mm 4 4 6 6

Spindle diameter M10 M10 M14 M10

Spindle length mm 16 16 21.5 16

Weight (without battery pack) kg 1.74 1.74 1.74 1.74

Batteries Chargers / Charge Times (Minutes)

Cat# V

DC

Ah Weight(kg)

DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119

DCB546/DCB606 18/54 (20/60 Max) 6.0/2.0 1.05 60 270 170 140 90 60 90 X

DCB547/DCB609 18/54 (20/60 Max) 9.0/3.0 1.46 75* 420 270 220 135* 75* 135* X

DCB548/DCB612 18/54 (20/60 Max) 12.0/4.0 1.44 120 540 350 300 180 120 180 X

DCB181 18 (20 Max) 1.5 0.35 22 70 45 35 22 22 22 45

DCB182/DCB204 18 (20 Max) 4.0 0.61 60/40** 185 120 100 60 60/40** 60 120

DCB183/DCB203 18 (20 Max) 2.0 0.40 30 90 60 50 30 30 30 60

DCB184/DCB205 18 (20 Max) 5.0 0.62 75/50** 240 150 120 75 75/50** 75 150

DCB185 18 (20 Max) 1.3 0.35 22 60 40 30 22 22 22 X

DCB187 18 (20 Max) 3.0 0.54 45 140 90 70 45 45 45 90

DCB189 18 (20 Max) 4.0 0.54 60 185 120 100 60 60 60 120

4

ENGLISH

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

4) Power tool use and care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

Batteries

Chargers/Charge Times (Minutes)

Cat #

DC

Weight



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.



Denotes risk of electricshock.



Denotes risk offire.

General Power Tool Safety Warnings



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work area safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

5

ENGLISH

c ) Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the

risk of starting the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

5) Battery tool use and care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys,

nails, screws or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

ADDITIONAL SPECIFIC SAFETY RULES

Safety Instructions for All Operations

a ) This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure

to follow all instructions listed below may result in electric

shock, fire and/or seriousinjury.

b ) Operations such as polishing are not recommended

to be performed with this power tool. Operations

for which the power tool was not designed may create

ahazard and cause personalinjury.

c ) Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safeoperation.

d ) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed can

break and flyapart.

e ) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can not be

adequately guarded orcontrolled.

f ) Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

flanges, the arbour hole of the accessory must fit the

locating diameter of the flange. Accessories that do

not match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause loss

ofcontrol.

g ) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheel for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged

accessories will normally break apart during this testtime.

h ) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying

debris generated by various operations. The dust mask or

respirator must be capable of filtrating particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearingloss.

i ) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away and

cause injury beyond immediate area ofoperation.

j ) Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting tool may contact hidden wiring. Contact

with a "live" wire will also make exposed metal parts

of the power tool "live" and could give the operator an

electricshock.

6

ENGLISH

k ) Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of

yourcontrol.

l ) Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

yourbody.

m ) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electricalhazards.

n ) Do not operate the power tool near flammable

materials. Sparks could ignite thesematerials.

o ) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution orshock.

FURTHER SAFETY INSTRUCTIONS FOR ALL

OPERATIONS

Causes and Operator Prevention

of Kickback

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or

snagging causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation at the point of

thebinding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also

break under theseconditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by taking

proper precautions as given below:

a ) Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up. The operator can control torque

reaction or kickback forces, if proper precautions aretaken.

b ) Never place your hand near the rotating accessory.

Accessory may kickback over yourhand.

c ) Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in direction opposite to the wheel’s movement at

the point ofsnagging.

d ) Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control

orkickback.

e ) Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent kickback

and loss ofcontrol.

Safety Warnings Specific for Grinding and

Abrasive Cutting-Off Operations

a ) Use only wheel types that are recommended for your

power tool and the specific guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and areunsafe.

b ) The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip.

An improperly mounted wheel that projects through the

plane of the guard lip cannot be adequatelyprotected.

c ) The guard must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator.

The guard helps to protect the operator from broken wheel

fragments and accidental contact with wheel and sparks

that could igniteclothing.

d ) Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel. Abrasive cut-off wheels are intended

for peripheral grinding, side forces applied to these wheels

may cause them toshatter.

e ) Always use undamaged wheel flanges that are

of correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus

reducing the possibility of wheel breakage. Flanges

for cut-off wheels may be different from grinding

wheelflanges.

f ) Do not use worn down wheels from larger power

tools. Wheel intended for larger power tool is not suitable

for the higher speed of a smaller tool and mayburst.

Additional Safety Warnings Specific for

Abrasive Cutting-Off Operations

a ) Do not “jam” the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheelbreakage.

b ) Do not position your body in line with and behind

the rotating wheel. When the wheel, at the point of

operations, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly atyou.

c ) When wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

the power tool motionless until the wheel comes to

a complete stop. Never attempt to remove the cut-

off wheel from the cut while the wheel is in motion

7

ENGLISH

otherwise kickback may occur. Investigate and take

corrective action to eliminate the cause of wheelbinding.

d ) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind, walk up

or kickback if the power tool is restarted in theworkpiece.

e ) Support panels or any oversized workpiece to

minimise the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own

weight. Supports must be placed under the workpiece

near the line of cut and near the edge of the workpiece on

both sides of thewheel.

f ) Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can causekickback.

Safety Warnings Specific for Sanding

Operations

a ) Do not use excessively oversized sanding disc

paper. Follow manufacturer’s recommendations,

when selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a laceration

hazard and may cause snagging, tearing of the disc

orkickback.

Safety Warnings Specific for Wire Brushing

Operations

a ) Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress

the wires by applying excessive load to the brush.

The wire bristles can easily penetrate light clothing and/

orskin.

b ) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to work and

centrifugalforces.

Additional Safety Rules for Grinders

a ) Do not use Type 11 (flaring cup) wheels on this tool.

Using inappropriate accessories can result ininjury.

b ) Always use side handle. Tighten the handle securely.

The side handle should always be used to maintain control

of the tool at alltimes.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

• Risk of dust from hazardoussubstances.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your DeWALT charger is double insulated in

accordance with IEC60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the

DeWALT

serviceorganisation.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm

2

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

SAVE THESE INSTRUCTIONS

Chargers

DeWALT chargers require no adjustment and are designed to be

as easy as possible tooperate.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.



WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only DeWALT rechargeable batteries. Other types of

batteries may burst causing personal injury anddamage.



CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

8

ENGLISH

• These chargers are not intended for any uses other than

charging DeWALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard 220-

240V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig. B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack

10

into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button

11

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to light or by

displaying problem pack or charger blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of thecharger.

Electronic Protection System

XR Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium-ion battery

pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

9

ENGLISH

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in

DeWALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or exceed

40 ˚C (104 ˚F) (such as outside sheds or metal buildings

in summer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.



WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.



WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation



WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from materials

that could contact them and cause a shortcircuit.

DeWALT batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests andCriteria.

In most instances, shipping a

DeWALT battery pack will be

excepted from being classified as a fully regulated Class 9

Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

All lithium-ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities, DeWALT

does not recommend air shipping lithium-ion battery packs

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100Whr.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Transporting the FLEXVOLT

TM

Battery

The

DeWALT FLEXVOLT

TM

battery has two modes: Use

andTransport.

Use Mode: When the FLEXVOLT

TM

battery stands alone or is

in a DeWALT 18V (20V Max) product, it will operate as an 18V

(20V Max) battery. When the FLEXVOLT

TM

battery is in a 54V

10

ENGLISH

(60V Max) or a 108V (120V Max) (two 54V (60V Max) batteries)

product, it will operate as a 54V(60V Max) battery.

Transport Mode: When the cap is

attached to the FLEXVOLT

TM

battery, the

battery is in Transport mode. Keep the

cap forshipping.

When in Transport mode, strings of cells are electrically

disconnected within the pack resulting in 3 batteries with a

lower Watt hour (Wh) rating as compared to 1 battery with a

higher Watt hour rating. This increased quantity of 3 batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hourbatteries.

For example, the Transport Wh rating might indicate 3x36 Wh,

meaning 3 batteries of 36 Wh each. The Use Wh rating might

indicate 108Wh (1battery implied).

Example of Use and Transport Label Marking

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels

on the charger and the battery pack may show the following

pictographs:

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Do not probe with conductiveobjects.

Do not charge damaged batterypacks.

Do not expose towater.

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for

theenvironment.

Charge DeWALT battery packs only with designated

DeWALT chargers. Charging battery packs other

than the designated DeWALT batteries with a

DeWALT charger may make them burst or lead to

other dangeroussituations.

Do not incinerate the batterypack.

USE (without transport cap). Example: Wh rating

indicates 108 Wh (1 battery with 108 Wh).

TRANSPORT (with built-in transport cap). Example:

Wh rating indicates 3 x 36 Wh (3batteries of 36 Wh).

Battery Type

The DCG405 operates on a 18V (20V Max) batterypack.

These battery packs may be used: DCB181, DCB182, DCB183,

DCB184 DCB185, DCB187, DCB189, DCB203, DCB204, DCB205,

DCB606, DCB609, DCB612, DCB546, DCB547, DCB548. Refer to

Technical Data for moreinformation.

Package Contents

The package contains:

1 Angle grinder

1 Guard

1 Side handle

1 Backing flange

1 Locking flange

1 Hex wrench (A9 only)

1 wrench(TW, KR only)

1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1 models)

2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2 models)

3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3 models)

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

11

ENGLISH

Wear eyeprotection.

Date Code Position (Fig. E)

The date code

15

, which also includes the year of manufacture,

is printed into thehousing.

Example:

2020 XX XX

Year of Manufacture

Description (Fig. A)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1

Slider switch

2

Lock-off lever

3

Spindle lock button

4

Spindle

5

Side handle

6

Backing flange

7

Locking flange

8

Guard

9

Guard release lever

10

Battery pack

11

Battery release button

Intended Use

Your cordless angle grinder has been designed for professional

cutting, grinding, sanding and wire brushapplications.

DO NOT use grinding wheels other than centre depressed

wheels and flapdiscs.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

Your cordless angle grinder is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Features

Kickback Brake™

When a pinch, stall, or bind-up event is sensed, the electronic

brake engages with maximum force to quickly stop the wheel,

reduce the movement of the grinder, and shut the grinder

off. The switch will need to be released then depressed to

restarttool.

Power-OFF™ Overload Protection

The power supply to the motor will be reduced in case of

motor overload. With continued motor overload, the tool will

shut off. The switch will need to be released then depressed

to restarttool. The tool will power off each time the current

load reaches the overload current value (motor burn-up point).

If continued overload shutdowns occur, apply less force/

weight on the tool until the tool will function without the

overloadengaging.

Anti-vibration Side Handle

The anti-vibration side handle offers added comfort by

absorbing the vibrations caused by thetool.

Soft Start Feature

The soft start feature allows a slow speed build-up to avoid an

initial jerk when starting. This feature is particularly useful when

working in confinedspaces.

No-Volt

The No-volt function stops the grinder restarting without the

switch being cycled if there is a break in the powersupply.

Electronic Clutch

The electronic torque limiting clutch reduces the maximum

torque reaction transmitted to the operator in case of jamming

of a disc. This feature also prevents the gearing and electric

motor from stalling. The torque limiting clutch has been factory-

set and cannot beadjusted.

Brake (A9 only)

Once the power is shut off, the brake stops the wheel spinning

more quickly than a unit without this feature. This improves

efficiency and increases user protection. Stopping time will vary

depending upon the type of wheel used.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.



WARNING: Use only DeWALT battery packs andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack

10

is fullycharged.

To Install the Battery Pack into the Tool

Handle

1. Align the battery pack

10

with the rails inside the tool’s

handle (Fig. B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button

11

and firmly pull the battery pack

out of the toolhandle.

12

ENGLISH

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig. B)

Some DeWALT battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge button.

A combination of the three green LED lights will illuminate

designating the level of charge left. When the level of charge

in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Attaching Side Handle (Fig. C)



WARNING: Before using the tool, check that the handle is

tightenedsecurely.

Screw the side handle

5

tightly into one of the holes on either

side of the gear case. The side handle should always be used to

maintain control of the tool at alltimes.

Rotating the Gear Case (Fig. A)

To improve user comfort, the gear case will rotate 90° for

cuttingoperations.

1. Remove the four corner screws attaching the gear case to

motorhousing.

2. Without separating the gear case from motor housing,

rotate the gear case head to desiredposition.

NOTE: If the gear case and motor housing become separated

by more than 3.17 mm, the tool must be serviced and

re-assembled by a

DeWALT service center. Failure to have the

tool serviced may motor and bearingfailure.

3. Reinstall screws to attach the gear case to the motor

housing. Tighten screws to 12.5 in.-lbs. torque.

Overtightening could cause screws tostrip.

Guards



CAUTION: Guards must be used with all grinding

wheels, cutting wheels, sanding flap discs, wire

brushes, and wire wheels. The tool may be used

without a guard only when sanding with conventional

sanding discs. Some applications may require purchasing

the correct guard from your local dealer or authorized

servicecentre.

NOTE: Edge grinding and cutting can be performed with Type

27 wheels designed and specified for this purpose; 6.35 mm

thick wheels are designed for surface grinding while thinner

Type 27 wheels need to be examined for the manufacturer's

label to see if they can be used for surface grinding or only

edge grinding/cutting. A Type 1 guard must be used for any

wheel where surface grinding is forbidden. Cutting can also be

performed by using a Type41 wheel and a Type 1guard.

NOTE: See the Accessories Chart to select the proper guard /

accessorycombination.

Mounting and Adjusting the One-Touch

TM

Guard (Fig. D)



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Adjusting the Guard

For guard adjustment, the guard release lever

9

engages

one of the alignment holes

14

on the guard collar using a

ratchetingfeature.

The engaging face is slanted and will ride over to the

next alignment hole when guard is rotated in a clockwise

direction (spindle facing user) but self-locks in the anti-

clockwisedirection.

Mounting Guard (Fig. D)

1. Press the guard release lever

9

.

2. While holding the guard release lever open, align the lugs

12

on the guard with the slots

13

on the gearcase.

3. Keeping the guard release lever open, push the guard down

until the guard lugs engage and rotate them in the groove

on the gear case hub. Release the guard releaselever.

4. With the spindle facing the operator, rotate the guard

clockwise into the desired working position. Press and hold

the guard release lever

9

to rotate the guard in the anti-

clockwisedirection.

NOTE: The guard body should be positioned between

the spindle and the operator to provide maximum

operatorprotection.

The guard release lever should snap into one of the

alignment holes

14

on the guard collar. This ensures that

the guard issecure.

5. To remove the guard, follow steps 1–3 of these instructions

inreverse.

Mounting Guards (Fig. D)(TW only)



WARNING: to reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Before

reconnecting the tool, depress and release the trigger

switch to ensure that the tool is off.



CAUTION: Guards must be used with this grinder.

When using the DCG405 grinder for cutting metal or masonry a

Type 1 guard must be used. Type 1 guards are available at extra

cost from

DeWALT distributors.

NOTE: Please refer to the grinding and cutting accessory chart

at the end of this section to see other accessories that can be

used with these grinders.

Mounting Closed (Type 1) Or Standard (Type

27) guard



CAUTION: Turn off and unplug the tool before making

anyadjustments or removing or installing attachments or

13

ENGLISH

acces-sories. Before reconnecting the tool, turn the switch

on and off to ensure that the tool is off.

Hubbed wheels install directly on the M10 (TW, KR), M14(A9)

spindle. Thread of accessory must match thread of spindle.

1. Loosen screw, until the guard lug

19

can rotate freely in the

groove

20

on the gear case hub.

2. Rotate guard

8

into desired working position. The guard

body should be positioned between the spindle and the

operator toprovide maximum operator protection.

3. Tighten the screw to secure the guard on the gear case

cover. (Fasten torque no less than 2.5 N-M). You should be

unable to rotate the guard by hand. Do not operate grinder

with a loose guard.

4. To remove the guard, loosen screw and pull up on the

guard.



CAUTION: Failure to properly seat the wheel before

turning the tool on may result in damage to the tool or

the wheel.

Flanges and Wheels

Mounting Non-Hubbed Wheels (Fig. E)



WARNING: Failure to properly seat the flanges and/or

wheel could result in serious injury (or damage to the tool

or wheel).



CAUTION: Included flanges must be used with depressed

centre Type 27 and Type 42 grinding wheels and

Type41 cutting wheels. See the Accessories Chart for

moreinformation.



WARNING: A closed, two-sided cutting wheel guard is

re quired when using cuttingwheels.



WARNING: Use of a damaged flange or guard or fail ure

to use proper flange and guard can re sult in injury due to

wheel breakage and wheel contact. See the Accessories

Chart for moreinformation.

1. Place the tool on a table, guardup.

2. Install the backing flange

6

on spindle

4

with the raised

centre (pilot) facing the wheel. Press the backing flange

intoplace.

3. Place wheel

19

against the backing flange, centreing the

wheel on the raised centre (pilot) of the backingflange.

4. While depressing the spindle lock button and with the hex

depressions facing away from the wheel, thread the locking

flange

7

on spindle so that the lugs engage the two slots

in thespindle.

5. While depressing the spindle lock button, tighten the

locking flange

7

by hand or using the wrench supplied.

(Only use a locking flange if it is in perfect condition.) Refer

to Accessory Chart to see flangedetails.

6. To remove the wheel, reverse the aboveprocedure.

Mounting Sanding Backing Pads (Fig. F)

NOTE: Use of a guard with sanding discs that use backing pads,

often called fiber resin discs, is not required. Since a guard is

not required for these accessories, the guard may or may not fit

correctly ifused.



WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

or wheel).



WARNING: Proper guard must be reinstalled for grinding

wheel, cutting wheel, sanding flap disc, wire brush or

wire wheel applications after sanding applications

arecomplete.

1. Place or appropriately thread backing pad

16

on

thespindle.

2. Place the sanding disc

17

on the backing pad

16

.

3. While depressing spindle lock

3

, thread the clamp nut

18

on the spindle, piloting the raised hub on the clamp nut into

the centre of san ding disc and backingpad.

4. Tighten the clamp nut by hand. Then depress the spindle

lock button while turning the sanding disc until the sanding

disc and clamp nut aresnug.

5. To remove the wheel, grasp and turn the backing pad and

sanding pad while depressing the spindle lockbutton.

Mounting and Removing Hubbed Wheels

(Fig. A)

Hubbed wheels install directly on the threaded spindle. Thread

of accessory must match thread ofspindle.

1. Remove backing flange by pulling away fromtool.

2. Thread the wheel on the spindle

4

byhand.

3. Depress the spindle lock button

3

and use a wrench to

tighten the hub of thewheel.

4. To remove the wheel, reverse the aboveprocedure.

NOTICE: Failure to properly seat the wheel before turning

the tool on may result in damage to the tool or thewheel.

Mounting Wire Cup Brushes and

Wire Wheels (Fig. A)



WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

or wheel).



CAUTION: To reduce the risk of personal injury,

wear work gloves when handling wire brushes and

wheels. They can becomesharp.



CAUTION: To reduce the risk of damage to the tool,

wheel or brush must not touch guard when mounted

or while in use. Undetectable damage could occur to

the accessory, causing wires to fragment from accessory

wheel orcup.

Wire cup brushes or wire wheels install directly on the threaded

spindle without the use of flanges. Use only wire brushes or

wheels provided with a threaded hub. These accessories are

available at extra cost from your local dealer or authorised

servicecentre.

1. Place the tool on a table, guardup.

2. Thread the wheel on the spindle byhand.

3. Depress spindle lock button

3

and use a wrench on the

hub of the wire wheel or brush to tighten thewheel.

4. To remove the wheel, reverse the aboveprocedure.

14

ENGLISH

NOTICE: To reduce the risk of damage to the tool, properly

seat the wheel hub before turning the toolon.

Prior to Operation

• Install the guard and appropriate disc or wheel. Do not use

excessively worn discs orwheels.

• Be sure the backing and locking flange are mounted

correctly. Follow the instructions given in the

AccessoryChart.

• Make sure the disc or wheel rotates in the direction of the

arrows on the accessory and thetool.

• Do not use a damaged accessory. Before each use, inspect

the accessory such as abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory

and run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart

during this testtime.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.



WARNING:

• Ensure all materials to be ground or cut are secured

inplace.

• Secure and support the workpiece. Use clamps or a

vice to hold and support the workpiece to a stable

platform. It is important to clamp and support the

workpiece securely to prevent movement of the

workpiece and loss of control. Movement of the

workpiece or loss of control may create a hazard and

cause personalinjury.

• Always wear regular working gloves while operating

thistool.

• The gear becomes very hot duringuse.

• Apply only a gentle pressure to the tool. Do not exert

side pressure on thedisc.

• Always install the guard and appropriate disc or

wheel. Do not use excessively worn disc orwheel.

• Avoid overloading. Should the tool become hot, let it

run a few minutes under no load condition to cool the

accessory. Do not touch accessories before they have

cooled. The discs become very hot duringuse.

• Never work with the grinding cup without a suitable

protection guard inplace.

• Do not use the power tool with a cut-offstand.

• Never use blotters together with bonded

abrasiveproducts.

• Be aware, the wheel continues to rotate after the tools

is switchedoff.

Proper Hand Position (Fig. G)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the side handle

5

,

with the other hand on the body of the tool, as shown in

FigureG.

Slider Switch (Fig. A)



CAUTION: Hold the side handle and body of the tool

firmly to maintain control of the tool at start up and

during use and until the wheel or accessory stops rotating.

Make sure the wheel has come to a complete stop be fore

laying the tooldown.

NOTE: To reduce unexpected tool movement, do not switch

the tool on or off while under load conditions. Allow the grinder

to run up to full speed before touching the work surface. Lift the

tool from the surface before turning the tool off. Allow the tool

to stop rotating before putting itdown.



WARNING: Before inserting the battery pack into the tool,

be sure the slider switch is in the off position by pressing

the rear part of the switch and releasing. Ensure the slider

switch is in the off position as described above after any

interruption in power. If the slider switch is locked on when

the power is connected, the tool will startunexpectedly.

To start the tool, slide the ON/OFF slider switch

1

toward

the front of the tool. To stop the tool, release the ON/OFF

sliderswitch.

For continuous operation, slide the switch toward the front of

the tool and press the forward part of the switch inward. To stop

the tool while operating in continuous mode, press the rear part

of the slider switch andrelease.

Spindle Lock Button (Fig. A)

The spindle lock button

3

is provided to prevent the spindle

from rotating when installing or removing wheels. Operate the

spindle lock only when the tool is turned off, unplugged from

the power supply, and has come to a completestop.

NOTICE: To reduce the risk of damage to the tool, do

not engage the spindle lock while the tool is operating.

Damage to the tool will result and attached accessory

may spin off possibly resulting ininjury.

To engage the lock, depress the spindle lock button

3

and rotate the spindle until you are unable to rotate the

spindlefurther.

15

ENGLISH

Surface Grinding, Sanding and Wire

Brushing



CAUTION: Always use the correct guard per the

instructions in thismanual.

To perform work on a the surface of a workpiece:

1. Allow the tool to reach full speed before touching the tool

to the worksurface.

2. Apply minimum pressure to the work surface, allowing

the tool to operate at high speed. Material removal rate is

greatest when the tool operates at highspeed.

3. Maintain an appropriate angle between the tool and work

surface. Refer to the chart according to particularfunction.

Function Angle

Grinding 20˚-30˚

Sanding with Flap Disc 5˚-10˚

Sanding with Backing Pad 5˚-15˚

Wire Brushing 5˚-10˚

4. Maintain contact between the edge of the wheel and the

worksurface.

- If grinding, sanding with flap discs or wire brushing

move the tool continuously in a forward and back

motion to avoid creating gouges in the worksurface.

- If sanding with a backing pad, move the tool constantly

in a straight line to prevent burning and swirling of

worksurface.

NOTE: Allowing the tool to rest on the work surface without

moving will damage the workpiece.

5. Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying itdown.



CAUTION: Use extra care when working over an edge, as

a sudden sharp movement of grinder may beexperienced.

Precautions To Take When Working on a

Painted Workpiece

1. Sanding or wire brushing of lead based paint is NOT

RECOMMENDED due to the difficulty of controlling the

contaminated dust. The greatest danger of lead poisoning is

to children and pregnantwomen.

2. Since it is difficult to identify whether or not a paint contains

lead without a chemical analysis, we recommend the

following precautions when sanding any paint:

Personal Safety

1. No children or pregnant women should enter the work area

where the paint sanding or wire brushing is being done

until all clean up iscompleted.

2. A dust mask or respirator should be worn by all persons

entering the work area. The filter should be replaced daily or

whenever the wearer has difficultybreathing.

NOTE: Only those dust masks suitable for working with lead

paint dust and fumes should be used. Ordinary painting

masks do not offer this protection. See your local hardware

dealer for the proper NIOSH-approvedmask.

3. NO EATING, DRINKING or SMOKING should be done in the

work area to prevent ingesting contaminated paint particles.

Workers should wash and clean up BEFORE eating, drinking

or smoking. Articles of food, drink, or smoking should not be

left in the work area where dust would settle onthem.

Environmental Safety

1. Paint should be removed in such a manner as to minimize

the amount of dustgenerated.

2. Areas where paint removal is occurring should be sealed

with plastic sheeting of 4 milsthickness.

3. Sanding should be done in a manner to reduce tracking of

paint dust outside the workarea.

Cleaning and Disposal

1. All surfaces in the work area should be vacuumed and

thoroughly cleaned daily for the duration of the sanding

project. Vacuum filter bags should be changedfrequently.

2. Plastic drop cloths should be gathered up and disposed

of along with any dust chips or other removal debris. They

should be placed in sealed refuse receptacles and disposed

of through regular trash pick-upprocedures.

During clean up, children and pregnant women should be

kept away from the immediate workarea.

3. All toys, washable furniture and utensils used by children

should be washed thoroughly before being usedagain.

Edge Grinding and Cutting



WARNING: Do not use edge grinding/cutting wheels for

surface grinding applications because these wheels are

not designed for side pressures encountered with surface

grinding. Wheel breakage and injury mayresult.



CAUTION: Wheels used for edge grinding and cutting

may break or kick back if they bend or twist while the tool

is being used. In all edge grinding/cutting operations, the

open side of the guard must be positioned away from

theoperator.

NOTICE: Edge grinding/cutting with a Type27 wheel

must be limited to shallow cutting and notching—less

than 13mm in depth when the wheel is new. Reduce the

depth of cutting/notching equal to the reduction of the

wheel radius as it wears down. Refer to the Accessories

Chart for more information. Edge grinding/cutting with a

Type 41 wheel requires usage of a Type 1guard.

16

ENGLISH

1. Allow the tool to reach full speed before touching the tool

to the worksurface.

2. Apply minimum pressure to the work surface, allowing

the tool to operate at high speed. Grinding/cutting rate is

greatest when the tool operates at highspeed.

3. Position yourself so that the open-underside of the wheel is

facing away fromyou.

4. Once a cut is begun and a notch is established in the

workpiece, do not change the angle of the cut. Changing

the angle will cause the wheel to bend and may cause

wheel breakage. Edge grinding wheels are not designed to

withstand side pressures caused bybending.

5. Remove the tool from the work surface before turning

the tool off. Allow the tool to stop rotating before laying

itdown.

Cutting Metal

For cutting with bonded abrasives, always use the

guardtype1.

When cutting, work with moderate feed, adapted to the

material being cut. Do not exert pressure onto the cutting disc,

tilt or oscillate themachine.

Do not reduce the speed of running down cutting discs by

applying sidewardpressure.

The machine must always work in an upgrinding motion.

Otherwise, the danger exists of it being pushed uncontrolled

out of thecut.

When cutting profiles and square bar, it is best to start at the

smallest crosssection.

Rough Grinding

Never use a cutting disc forroughing.

Always use the guard type27.

The best roughing results are achieved when setting the

machine at an angle of 30° to 40°. Move the machine back and

forth with moderate pressure. In this manner, the workpiece

will not become too hot, does not discolour and no grooves

areformed.

Cutting Stone

The machine shall be used only for drycutting.

For cutting stone, it is best to use a diamond cutting disc.

Operate the machine only with additional dust protectionmask.

Working Advice

Exercise caution when cutting slots in structuralwalls.

Slots in structural walls are subject to the country-specific

regulations. These regulations are to be observed under all

circumstances.Before beginning work, consult the responsible

structural engineer, architect or the constructionsupervisor.

MAINTENANCE

Your DeWALT power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Your power tool requires no additionallubrication.

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Optional Accessories



WARNING: Since accessories, other than those offered

by DeWALT, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DeWALT recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be replaced when it fails to

produce sufficient power on jobs that were easily done before.

At the end of its technical life, discard it with due care for our

environment:

• Run the battery pack down completely, then remove it from

thetool.

Li-Ion cells are recyclable. Take them to your dealer or a local

recycling station. The collected battery packs will be recycled or

disposed ofproperly.

17

ENGLISH

After Service and Repair

• DEWALT service centers are staffed with trained personnel

to provide customers with efficient and reliable product

service.

• We do not take any responsibility when you have repaired

in unauthorized service center. You can refer to the leaflet

of CONTACT CENTER LOCATOR in product package and

contact us through hotline, website or social media to find

the nearest DEWALT service center around you.

18

ENGLISH

Accessory Chart

Guard Type Accessory Description How to Fit Grinder

Type 27

Guard

Type 27

Guard

Depressed centre

grinding disc

Type 27 guard

Backing flange

Type 27 depressed

centre wheel

Locking flange

Flap wheel

Wire wheels

Wire wheels with

threaded nut

Type 27 guard

Wire wheel

Wire cup with

threaded nut

Type 27 guard

Wire brush

Backing pad/

sanding sheet

Type 27 guard

Rubber backing pad

Sanding disc

Clamp nut

ページが読み込まれています...

DeWalt DCG405 ユーザーマニュアル

DeWalt DCG405 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント