Dell PowerEdge C5230 クイックスタートガイド

www.dell.com | support.dell.com

Dell PowerEdge C5230

Getting Started

With Your

System

使用入门

Mengaktifkan Sistem Anda

はじめに

시스템 시작하기

www.dell.com | support.dell.com

Dell PowerEdge C5230

Getting Started

With Your

System

Regulatory Model B04S

Notes, Cautions, and Warnings

____________________

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.

Intel

®

and Intel

®

Xeon

®

are registered trademarks of Intel Corporation in the U.S. and other countries.

Microsoft

®

and Windows

®

are either trademarks or registered trademarks of Microsoft Corporation

in the United States and/or other countries. Red Hat

®

and Red Hat Enterprise Linux

®

are registered

trademarks of Red Hat, Inc. in the United States and/or other countries. SUSE™ is a trademark of

Novell Inc. in the United States and other countries. Citrix

®

, Xen

®

, and XenServer

®

are either

registered trademarks or trademarks of Citrix Systems, Inc. in the United States and/or other countries.

VMware

®

is a registered trademarks or trademarks of VMWare, Inc. in the United States or other

countries.

Regulatory Model B04S

2013 - 09 P/N JF9MM Rev. A00

NOTE:

A NOTE indicates important information that helps you make better use of

your system.

CAUTION:

A CAUTION indicates potential damage to hardware or loss of data if

instructions are not followed.

WARNING:

A WARNING indicates a potential for property damage, personal

injury, or death.

Installation and Configuration

3

This server is intended for installation only in restricted access locations as

defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions

apply:

• Access can only be gained by service persons or by users who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.

• Access is through the use of a tool or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

Installation and Configuration

Unpacking the System

Unpack your system and identify each item.

Installing the Tool-Less Rail Solution

CAUTION:

Restricted Access Location

WARNING:

Before performing the following procedure, review and follow the

safety instructions that came with the system.

WARNING:

Whenever you need to lift the system, get others to assist you. To

avoid injury, do not attempt to lift the system by yourself.

WARNING:

The system is not fixed to the rack or mounted on the rails. To avoid

personal injury or damage to the system, you must adequately support the system

during installation and removal.

WARNING:

To avoid a potential electrical shock hazard, a third wire safety

grounding conductor is necessary for the rack installation. The rack equipment

must provide sufficient airflow to the system to maintain proper cooling.

CAUTION:

When installing rails in a square-hole rack it is important to ensure

that the square peg slides through the square holes.

CAUTION:

Square studs must be flush with the rack posts to install properly.

4

Installation and Configuration

1

Pull on the latch release buttons on the end piece midpoints to open the

rail latches.

Figure 1-1. Unlocking the Rail Latches

2

Align the end pieces of the rails on the vertical rack flanges to seat the pegs

in the bottom hole of the first U and the top hole of the second U. Engage

the back end of the rail until the latch locks in place.

Figure 1-2. Aligning the Rails on the Rack

3

Repeat steps 1 and 2 to position and seat the front end piece on the

vertical flange.

NOTE:

The rails can be used in both square-hole and round-hole racks.

NOTE:

To remove the rails, pull on the latch release button on the end piece

midpoint and unseat each rail.

Front

Back

Installation and Configuration

5

Installing the System

Empting the System Chassis

1

Unplug the power cable from the power supply unit.

Figure 1-3. Unplugging the Power Cable from the Power Supply Unit

2

Pull out the power supply unit handle.

Figure 1-4. Releasing the Power Supply Unit Handle

3

Press down on the release latch



.

WARNING:

Before installation, it is recommended that you remove the sleds and

power supplies from the system to reduce weight.

6

Installation and Configuration

4

Pull the power supply unit out of the system



.

Figure 1-5. Removing the Power Supply Unit

5

Press the release latch down



.

6

Pull the sled out of the system



.

Figure 1-6. Removing the Sled

Installation and Configuration

7

Installing the System Into the Rack

1

Slide the system into the rack.

2

If present, remove the chassis stabilizer shipping bracket (optional) from

the rack.

3

Tighten the captive thumbscrews to secure the ears of the system to the

front of the rack.

Figure 1-7. Securing the Chassis on the Rails

WARNING:

Whenever you need to lift the system, get others to assist you. To

avoid injury, do not attempt to lift the system by yourself.

NOTE:

To transport systems already installed in the rack, ensure that the two

chassis stabilizer shipping brackets (optional) are in place.

NOTE:

Make sure the latch release mechanism is engaged correctly.

8

Installation and Configuration

Populating the System

1

Push the power supply unit into the system until flush with the case and

the release latch locks.

Figure 1-8. Installing the Power Supply Unit

2

Close the power supply unit handle.

Figure 1-9. Securing the Power Supply Unit Handle

3

Plug the chassis power cable into the power supply unit.

Installation and Configuration

9

Figure 1-10. Connecting the Power Cable to the Power Supply Unit

Figure 1-11. Locating the Power Supply Unit Sockets

4

Push the sled into the system until flush with the case and the release latch

locks.

NOTE:

The correct configuration of the integral chassis AC power cables to the

power supply unit sockets is shown in the following illustration.

1 2 3 4 5 6 7 8 9 10 11 12

PSU1 PSU2

10

Installation and Configuration

Figure 1-12. Installing the Sled

Connecting the Keyboard, Mouse, and Monitor

Figure 1-13. Connecting Perhipherals

The connector on the front of your system has an icon indicating which cable

to plug in. You can connect a keyboard, mouse, or monitor (optional).

Installation and Configuration

11

Connecting the Power Cables

1

On the back of the system, connect the main power cable to the system’s

power socket.

Figure 1-14. Connecting Power Cables

2

Plug the other end of the power cable into a grounded electrical outlet or a

separate power source such as an uninterrupted power supply or a power

distribution unit.

Turning On the System

When connected to a power source the system automatically powers on.

Complete the Operating System Setup

To install an operating system for the first time, see the installation and

configuration documentation for your operating system. Be sure the

operating system is installed before installing hardware or software not

purchased with the system.

NOTE:

AC Port 1 provides power to PSU1, AC Port 2 provides power to PSU2. For

more information, see step 3 of Populating the System.

NOTE:

For the latest information on supported operating systems, see

dell.com/ossupport.

AC Port 2

AC Port 1

12

Installation and Configuration

Other Information You May Need

See the Hardware Owner’s Manual at dell.com/support/manuals for

information about system features, troubleshooting, and component

replacement.

Dell systems management application documentation provides information

about installing and using the systems management software. This document

is available online at dell.com/support/manuals.

NOM Information (Mexico Only)

The following information is provided on the device described in this

document in compliance with the requirements of the official Mexican

standards (NOM):

WARNING:

See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

NOTE:

Always check for updates on dell.com/support/manuals and read the

updates first because they often supersede information in other documents.

Importer Dell Inc. de México, S.A. de C.V.

Paseo de la Reforma 2620-11° Piso

Col. Lomas Atlas

11950 México, D.F.

Model number B04S

Supply voltage 200-240 VAC

Frequency 50/60 Hz

Current consumption 9A for each power inlet

Technical Specifications

13

Technical Specifications

Processor (Per System Board)

Processor type Intel Xeon Processor E3-1240v3, E3-

1280v3

Memory (Per System Board)

Architecture Dual Channel Unbuffered DDR3 1600

Memory module sockets 4

Memory module capacities

Minimum RAM 2 GB

Maximum RAM 32 GB

Drives (Per System Board)

Option 1: 2.5" hard drives

Option 2: 3.5" hard drives

SATA 6 Gb (4 channels)

SATA 6 Gb (2 channels)

Connectors (Per System Board)

Front

NIC 10/100/1G (RJ45)

2

USB 2.0 (through optional Y-cable)

2

Video (through optional Y-cable)

1

Video

Video type AST2300

Video memory 8 MB DDR3 SDRAM

14

Technical Specifications

Power

AC power supply (per power supply)

Wa tt ag e

1400 W

Voltage

200-240 VAC, 50/60 Hz

Heat dissipation

572.88 BTU/hr. max.

Maximum inrush current

55 A max.

Heat Dissipation

System chassis

12-sled

7.2 K BTU/hr. max.

Physical

Height 13 cm (5.1 in)

Width 44.7 cm (17.6 in)

Depth 75 cm (29.5 in)

Weight (loaded: maximum weight)

12 sled configuration

48.13 kg (106.11 lbs.)

Weight (empty)

12 sled configuration

32.02 kg (70.59 lbs.)

Technical Specifications

15

Environmental

NOTE:

For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10°C to 35°C (50°F to 95°F) with a

maximum temperature gradation of 10°C

(per hour)

NOTE:

For altitudes above 2,950 feet, the

maximum operating temperatures derated to

1°F/550 ft.

Storage

–40°C to 65°C (-40°F to 149°F) with a

maximum temperature gradation of 20°C

per hour

Relative Humidity

Operating

20% to 80% (noncondensing) with a

maximum humidity gradation of 10% per

hour

Storage

5% to 85% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz

Storage

1.87 Grms at 10–500 Hz for 15 minutes

Maximum shock

Operating

One shock pulse in the positive z axis (one

pulse on each side of the system) of 31 G for

2.6 ms in the operational orientation

Storage

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of

71 G for up to 2 ms.

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of

22 G faired square wave pulse with velocity

change at 200 inches/second

16

Technical Specifications

Environmental (continued)

Altitude

Operating

-16 to 3,048 m (-50 to 10,000 ft.)

Storage

-16 to 10,600 m (-50 to 35,000 ft.)

Airborne Contaminant Level

Class

G1 as defined by ISA-S71.04-1985

Acoustics

Sound Power (Units: LwAd-UL,bels)

Idle in 23 ± 2

°

C ambient

<= 7.0

CPU with 50% loading & HDD stress

in 23 ± 2

°

C ambient

<= 7.5

NOTE:

LwAd-UL is the upper limit sound power level (LwAd) calculated by ISO 9296

(1988) and measured in accordance with ISO7779 (1999).

www.dell.com | support.dell.com

Dell PowerEdge C5230

使用入门

规格型号 B04S

注、小心和警告

____________________

Dell™ DELL PowerEdge™ Dell Inc. Intel

®

Intel

®

Xeon

®

Intel Corporation / /

Microsoft

®

Windows

®

Microsoft Corporation / /

Red Hat

®

Red Hat Enterprise Linux

®

Red Hat, Inc. / /

SUSE™ Novell Inc. / Citrix

®

Xen

®

XenServer

®

Citrix Systems, Inc. / / VMware

®

VMWare, Inc. /

规格型号 B04S

2013 - 09 P/N JF9MM Rev.A00

注：

“ 注 ” 表示帮助您更好地使用系统的重要信息。

小心：

“ 小心 ” 表示如果不遵循说明，就有可能损坏硬件或导致数据丢失。

警告：

“ 警告 ” 表示可能会导致财产损失、人身伤害甚至死亡。

ページを読み込んでいます...

Dell PowerEdge C5230 クイックスタートガイド

関連論文