MSI B450PVDHMAX ユーザーマニュアル

1

<󷶷󳚹 1> Contents

Contents

Safety Information ........................................................................................... 2

Specifications ...................................................................................................3

Package contents ............................................................................................6

Rear I/O Panel .................................................................................................7

LAN Port LED Status Table .................................................................................7

Overview of Components ................................................................................8

CPU Socket .........................................................................................................9

DIMM Slots ........................................................................................................10

PCI_E1~3: PCIe Expansion Slots ......................................................................11

JFP1, JFP2: Front Panel Connectors ...............................................................12

SATA1~4: SATA 6Gb/s Connectors....................................................................12

M2_1: M.2 Slot (Key M) .....................................................................................13

ATX_PWR1, CPU_PWR1: Power Connectors....................................................13

JUSB1~2: USB 2.0 Connectors .........................................................................14

JUSB3: USB 3.2 Gen1 Connector .....................................................................14

CPU_FAN1, SYS_FAN1~2: Fan Connectors ......................................................15

JTPM1: TPM Module Connector .......................................................................16

JCI1: Chassis Intrusion Connector ...................................................................16

JAUD1: Front Audio Connector ......................................................................... 17

JCOM1: Serial Port Connector .........................................................................17

JLPT1: Parallel Port Connector........................................................................17

JBAT1: Clear CMOS (Reset BIOS) Jumper .......................................................18

EZ Debug LED: Debug LED indicators ..............................................................18

JRGB1: RGB LED strip connector .....................................................................18

BIOS Setup ..................................................................................................... 19

Entering BIOS Setup .........................................................................................19

Resetting BIOS ..................................................................................................20

Updating BIOS ...................................................................................................20

Software Description .....................................................................................21

Installing Windows

®

10 .....................................................................................21

Installing Drivers ..............................................................................................21

Installing Utilities ..............................................................................................22

Thank you for purchasing the MSI

®

B450M PRO-VDH MAX

motherboard. This User Guide gives information about

board layout, component overview, BIOS setup and software

installation.

2

Safety Information

y The components included in this package are prone to damage from electrostatic

discharge (ESD). Please adhere to the following instructions to ensure successful

computer assembly.

y Ensure that all components are securely connected. Loose connections may cause

the computer to not recognize a component or fail to start.

y Hold the motherboard by the edges to avoid touching sensitive components.

y It is recommended to wear an electrostatic discharge (ESD) wrist strap when

handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is

not available, discharge yourself of static electricity by touching another metal object

before handling the motherboard.

y Store the motherboard in an electrostatic shielding container or on an anti-static

pad whenever the motherboard is not installed.

y Before turning on the computer, ensure that there are no loose screws or metal

components on the motherboard or anywhere within the computer case.

y Do not boot the computer before installation is completed. This could cause

permanent damage to the components as well as injury to the user.

y If you need help during any installation step, please consult a certified computer

technician.

y Always turn off the power supply and unplug the power cord from the power outlet

before installing or removing any computer component.

y Keep this user guide for future reference.

y Keep this motherboard away from humidity.

y Make sure that your electrical outlet provides the same voltage as is indicated on

the PSU, before connecting the PSU to the electrical outlet.

y Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.

y All cautions and warnings on the motherboard should be noted.

y If any of the following situations arises, get the motherboard checked by service

personnel:

 Liquid has penetrated into the computer.

 The motherboard has been exposed to moisture.

 The motherboard does not work well or you can not get it work according to

user guide.

 The motherboard has been dropped and damaged.

 The motherboard has obvious sign of breakage.

y Do not leave this motherboard in an environment above 60C (140F), it may

damage the motherboard.

3

Safety Information Speciﬁcations

Specifications

CPU

Supports 1st, 2nd and 3rd Gen AMD Ryzen™/ Ryzen™ with

Radeon™ Vega Graphics and 2nd Gen AMD Ryzen™ with

Radeon™ Graphics/ Athlon™ with Radeon™ Vega Graphics

Desktop Processors for Socket AM4

Chipset AMD

®

B450 chipset

Memory

y 4x DDR4 memory slots, support up to 64GB*

 Supports 1866/ 2133/ 2400/ 2667Mhz (by JEDEC)

 Supports 2667/ 2800/ 2933/ 3000/ 3066/ 3200/ 3466 MHz

(by A-XMP OC MODE)

y

Dual channel memory architecture

y

Supports ECC UDIMM memory (non-ECC mode)

y

Support non-ECC UDIMM memory

* Please refer www.msi.com for more information on

compatible memory.

Expansion Slots

y 1x PCIe 3.0 x16 slot

 1st, 2nd and 3rd Gen AMD Ryzen™ support x16 mode

 Ryzen™ with Radeon™ Vega Graphics and 2nd Gen AMD

Ryzen™ with Radeon™ Graphics support x8 mode

 Athlon™ with Radeon™ Vega Graphics support x4 mode

y 2x PCIe 2.0 x1 slots

Onboard

Graphics

y 1x VGA port, supports a maximum resolution of

2048x1280@60Hz, 1920x1200@60Hz*

y 1x DVI-D port, supports a maximum resolution of

1920x1200@60Hz*

y 1x HDMI™ 1.4 port, supports a maximum resolution of

4096x2160 @30Hz, 2560x1600 @60Hz*

* Only support when using Ryzen™ with Radeon™ Vega

Graphics, 2nd Gen AMD Ryzen™ with Radeon™ Graphics and

Athlon™ with Radeon™ Vega Graphics processors

* Maximum shared memory of 2048 MB

Storage

AMD

®

B450 Chipset

y 4x SATA 6Gb/s ports

 Supports RAID 0, RAID1 and RAID 10

y 1x M.2 slot (Key M)

 Supports PCIe 3.0 x4 (1st, 2nd and 3rd Gen AMD

Ryzen™/ Ryzen™ with Radeon™ Vega Graphics and 2nd

Gen AMD Ryzen™ with Radeon™ Graphics) or PCIe 3.0 x2

(Athlon™ with Radeon™ Vega Graphics) and SATA 6Gb/s

 Supports 2242/ 2260 /2280 storage devices

Continued on next page

4

Speciﬁcations

Continued from previous page

Audio

Realtek

®

ALC892 Codec

y 7.1-Channel High Definition Audio

LAN 1x Realtek

®

8111H Gigabit LAN controller

USB

AMD

®

B450 Chipset

y 2x USB 3.2 Gen1 (SuperSpeed USB) ports through the

internal USB 3.2 Gen1 connector

y 8x USB 2.0 (High-speed USB) ports (4 ports on the back

panel, 4 ports available through the internal USB connectors)

y AMD

®

processor

y 4x USB 3.2 Gen1 (SuperSpeed USB) Type-A ports on the

back panel

I/O Controller NUVOTON 6795D Controller Chip

Hardware

Monitor

y CPU/System temperature detection

y CPU/System fan speed detection

y CPU/System fan speed control

Form Factor

y m-ATX Form Factor

y 9.6 in. x 9.6 in. (24.4 cm x 24.4 cm)

BIOS Features

y 1x 256 Mb flash

y UEFI AMI BIOS

y ACPI 6.1, SM BIOS 2.8

y Multi-language

Back Panel

Connectors

y 1x PS/2 keyboard/ mouse combo port

y 4x USB 2.0 Type-A ports

y 1x VGA port

y 1x DVI-D port

y 1x HDMI™ port

y 4x USB 3.2 Gen1 Type-A ports

y 1x LAN (RJ45) port

y 3x audio jacks

Internal

Connectors

y 1x 24-pin ATX main power connector

y 1x 8-pin ATX 12V power connector

y 4x SATA 6Gb/s connectors

y 2x USB 2.0 connectors (supports additional 4 USB 2.0 ports)

y 1x USB 3.2 Gen1 connector (supports additional 2 USB 3.2

Gen1 ports)

Continued on next page

5

Speciﬁcations Speciﬁcations

Continued from previous page

Internal

Connectors

y 1x 4-pin CPU fan connector

y 2x 4-pin system fan connectors

y 1x Front panel audio connector

y 2x Front panel connectors

y 1x TPM module connector

y 1x Chassis Intrusion connector

y 1x Serial port connector

y 1x Parallel port connector

y 1x RGB LED strip connector

y 1x Clear CMOS jumper

Software

y Drivers

y APP MANAGER

y SUPER CHARGER

y COMMAND CENTER

y LIVE UPDATE 6

y MYSTIC LIGHT

y SMART TOOL

y X-BOOST

y RAMDISK

y Norton

™

Security

y Google Chrome

™

,Google Toolbar, Google Drive

y CPU-Z MSI GAMING

6

Package contents

Please check the contents of your motherboard package. It should contain:

y Motherboard

y Driver DVD

y Quick Installation Guide

y I/O Shielding

y SATA 6G Cable x2

y Case Badge

y Product registration card

y M.2 Screw x1

Important

If any of the above items are damaged or missing, please contact your retailer.

7

Package contents Rear I/O Panel

Rear I/O Panel

Link/ Activity LED

Status Description

Off No link

Yellow Linked

Blinking Data activity

Speed LED

Status Description

Off 10 Mbps connection

Green 100 Mbps connection

Orange 1 Gbps connection

LAN Port LED Status Table

Audio 7.1-channel Configuration

To configure 7.1-channel audio, you have to connect front audio I/O module to JAUD1

connector and follow the below steps.

1. Click on the Realtek HD Audio Manager > Advanced Settings to open the dialog

below.

2. Select Mute the rear output device, when a front headphone plugged in.

3. Plug your speakers to audio jacks on rear and front I/O panel. When you plug into

a device at an audio jack, a dialogue window will pop up asking you which device is

current connected.

PS/2

LAN

USB 3.2 Gen1USB 2.0

USB 2.0

DVI-D

VGA

Line-in

Line-out

Mic in

8

Overview of Components

CPU_FAN1

CPU SocketSYS_FAN1

PCI_E3

JAUD1

PCI_E2

M2_1

PCI_E1

DIMMA1

DIMMA2

DIMMB1

DIMMB2

JBAT1

JCI1

JFP2

JFP1

JUSB3

ATX_PWR1

CPU_PWR1

EZ Debug LED

SATA2

SATA1

JTPM1

JUSB1

JLPT1

JRGB1

JUSB2

JCOM1

SYS_FAN2

SATA34

Overview of Components

9

Overview of Components Overview of Components

CPU Socket

Please install the CPU into the CPU socket as shown below.

Important

y

When changing the processor, the system configuration could be cleared and reset

BIOS to default values due to the AM4 processor󽶳s architecture.

y

Always unplug the power cord from the power outlet before installing or removing

the CPU.

y

When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink

is necessary to prevent overheating and maintain system stability.

y

Confirm that the CPU heatsink has formed a tight seal with the CPU before booting

your system.

y

Overheating can seriously damage the CPU and motherboard. Always make sure

the cooling fans work properly to protect the CPU from overheating. Be sure to apply

an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to

enhance heat dissipation.

y

If you purchased a separate CPU and heatsink/ cooler, Please refer to the

documentation in the heatsink/ cooler package for more details about installation.

3

5

6

8

2

10

Overview of Components

DIMM Slots

Please install the memory module into the DIMM slot as shown below.

1

2

3

2

Memory module installation recommendation

DIMMB2

DIMMA2 DIMMA2

DIMMB2

DIMMB1

DIMMA2

DIMMA1

11

Overview of Components Overview of Components

Important

y

Always insert memory modules in the DIMMA2 slot first.

y

Due to chipset resource usage, the available capacity of memory will be a little less

than the amount of installed.

y

Based on processor specification, the Memory DIMM voltage below 1.35V is

suggested to protect the processor.

y

Due to AM4 CPU/memory controller official specification limitation, the frequency

of memory modules may operate lower than the marked value under the default

state. Please refer www.msi.com for more information on compatible memory.

PCI_E1~3: PCIe Expansion Slots

Important

y

When adding or removing expansion cards, always turn off the power supply and

unplug the power supply power cable from the power outlet. Read the expansion

card󽶳s documentation to check for any necessary additional hardware or software

changes.

y

If you install a large and heavy graphics card, you need to use a tool such as MSI

Gaming Series Graphics Card Bolster to support its weight to prevent deformation of

the slot.

Processors

Slots

1st, 2nd and

3rd Gen AMD

Ryzen™

Ryzen™ with Radeon™

Vega Graphics and 2nd

Gen AMD Ryzen™ with

Radeon™ Graphics

Athlon™ with

Radeon™ Vega

Graphics

PCI_E1 PCIe 3.0 x16 PCIe 3.0 x8 PCIe 3.0 x4

PCI_E2 PCIe 2.0 x1 PCIe 2.0 x1 PCIe 2.0 x1

PCI_E3 PCIe 2.0 x1 PCIe 2.0 x1 PCIe 2.0 x1

12

Overview of Components

SATA1~4: SATA 6Gb/s Connectors

These connectors are SATA 6Gb/s interface ports. Each connector can connect to one

SATA device.

SATA3

SATA4

SATA2

SATA1

Important

y

Please do not fold the SATA cable at a 90-degree angle. Data loss may result during

transmission otherwise.

y

SATA cables have identical plugs on either sides of the cable. However, it is

recommended that the flat connector be connected to the motherboard for space

saving purposes.

JFP1, JFP2: Front Panel Connectors

These connectors connect to the switches and LEDs on the front panel.

1

2 10

9

+

+-

--

-

+

Power LED

HDD LED Reset Switch

Reserved

Power Switch

1 HDD LED + 2 Power LED +

3 HDD LED - 4 Power LED -

5 Reset Switch 6 Power Switch

7 Reset Switch 8 Power Switch

9 Reserved 10 No Pin

JFP2

1

+

-

Speaker

Buzzer

1 Speaker - 2 Buzzer +

3 Buzzer - 4 Speaker +

HDD LED

RESET SW

HDD LED

HDD LED -

HDD LED +

POWER LED -

POWER LED +

POWER LED

JFP1

13

Overview of Components Overview of Components

ATX_PWR1, CPU_PWR1: Power Connectors

These connectors allow you to connect an ATX power supply.

Important

Make sure that all the power cables are securely connected to a proper ATX power

supply to ensure stable operation of the motherboard.

M2_1: M.2 Slot (Key M)

Please install the M.2 solid-state drive (SSD) into the M.2 slot as shown below.

1

2

3

4

5

30

24

131

12

ATX_PWR1

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V

3 Ground 15 Ground

4 +5V 16 PS-ON#

5 Ground 17 Ground

6 +5V 18 Ground

7 Ground 19 Ground

8 PWR OK 20 Res

9 5VSB 21 +5V

10 +12V 22 +5V

11 +12V 23 +5V

12 +3.3V 24 Ground

5

4

1

8

CPU_PWR1

1 Ground 5 +12V

2 Ground 6 +12V

3 Ground 7 +12V

4 Ground 8 +12V

14

Overview of Components

JUSB3: USB 3.2 Gen1 Connector

This connector allows you to connect USB 3.2 Gen1 ports on the front panel.

1 10

1120

1 Power 11 USB2.0+

2 USB3_RX_DN 12 USB2.0-

3 USB3_RX_DP 13 Ground

4 Ground 14 USB3_TX_C_DP

5 USB3_TX_C_DN 15 USB3_TX_C_DN

6 USB3_TX_C_DP 16 Ground

7 Ground 17 USB3_RX_DP

8 USB2.0- 18 USB3_RX_DN

9 USB2.0+ 19 Power

10 NC 20 No Pin

Important

Note that the Power and Ground pins must be connected correctly to avoid possible

damage.

JUSB1~2: USB 2.0 Connectors

These connectors allow you to connect USB 2.0 ports on the front panel.

Important

y

Note that the VCC and Ground pins must be connected correctly to avoid possible

damage.

y

In order to recharge your iPad,iPhone and iPod through USB ports, please install

MSI

®

SUPER CHARGER utility.

1

2 10

9

1 VCC 2 VCC

3 USB0- 4 USB1-

5 USB0+ 6 USB1+

7 Ground 8 Ground

9 No Pin 10 NC

15

Overview of Components Overview of Components

CPU_FAN1, SYS_FAN1~2: Fan Connectors

Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC

Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed

with speed control signal. DC Mode fan connectors control fan speed by changing

voltage. When you plug a 3-pin (Non-PWM) fan to a fan connector in PWM mode, the

fan speed will always maintain at 100%, which might create a lot of noise. You can

follow the instruction below to adjust the fan connector to PWM or DC Mode.

Switching fan mode and adjusting fan speed

You can switch between PWM mode and DC mode and adjust fan speed in BIOS >

HARDWARE MONITOR.

Select PWM mode or DC mode

Important

Make sure fans are working properly after switching the PWM/ DC mode.

There are gradient points of the fan speed that allow you to

adjust fan speed in relation to CPU temperature.

Default PWM Mode

fan connector

Default DC Mode fan

connector

1

CPU_FAN1

1

SYS_FAN1/ 2

PWM Mode pin definition

1 Ground 2 +12V

3 Sense 4 Speed Control Signal

DC Mode pin definition

1 Ground 2 Voltage Control

3 Sense 4 NC

Pin definition of fan connectors

16

Overview of Components

JTPM1: TPM Module Connector

This connector is for TPM (Trusted Platform Module). Please refer to the TPM

security platform manual for more details and usages.

1

2 14

13

1 LPC Clock 2 3V Standby power

3 LPC Reset 4 3.3V Power

5 LPC address & data pin0 6 Serial IRQ

7 LPC address & data pin1 8 5V Power

9 LPC address & data pin2 10 No Pin

11 LPC address & data pin3 12 Ground

13 LPC Frame 14 Ground

JCI1: Chassis Intrusion Connector

This connector allows you to connect the chassis intrusion switch cable.

Normal

(default)

Trigger the chassis

intrusion event

Using chassis intrusion detector

1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis.

2. Close the chassis cover.

3. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.

4. Set Chassis Intrusion to Enabled.

5. Press F10 to save and exit and then press the Enter key to select Yes.

6. Once the chassis cover is opened again, a warning message will be displayed on

screen when the computer is turned on.

Resetting the chassis intrusion warning

1. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.

2. Set Chassis Intrusion to Reset.

3. Press F10 to save and exit and then press the Enter key to select Yes.

17

Overview of Components Overview of Components

JAUD1: Front Audio Connector

This connector allow you to connect audio jacks on the front panel.

1

2 10

9

1 MIC L 2 Ground

3 MIC R 4 NC

5 Head Phone R 6 MIC Detection

7 SENSE_SEND 8 No Pin

9 Head Phone L 10 Head Phone Detection

JCOM1: Serial Port Connector

This connector allows you to connect the optional serial port with bracket.

1

2 10

9

1 DCD 2 SIN

3 SOUT 4 DTR

5 Ground 6 DSR

7 RTS 8 CTS

9 RI 10 No Pin

1

2 26

25

1 RSTB# 2 AFD# 3 PRND0

4 ERR# 5 PRND1 6 PINIT#

7 PRND2 8 LPT_SLIN# 9 PRND3

10 Ground 11 PRND4 12 Ground

13 PRND5 14 Ground 15 PRND6

16 Ground 17 PRND7 18 Ground

19 ACK# 20 Ground 21 BUSY

22 Ground 23 PE 24 Ground

25 SLCT 26 No Pin

JLPT1: Parallel Port Connector

This connector allows you to connect the optional parallel port with bracket.

18

Overview of Components

JBAT1: Clear CMOS (Reset BIOS) Jumper

There is CMOS memory onboard that is external powered from a battery located on

the motherboard to save system configuration data. If you want to clear the system

configuration, set the jumpers to clear the CMOS memory.

Keep Data

(default)

Clear CMOS/ Reset

BIOS

Resetting BIOS to default values

1. Power off the computer and unplug the power cord.

2. Use a jumper cap to short JBAT1 for about 5-10 seconds.

3. Remove the jumper cap from JBAT1.

4. Plug the power cord and power on the computer.

EZ Debug LED: Debug LED indicators

These LEDs indicate the status of the motherboard.

CPU - indicates CPU is not detected or fail.

DRAM - indicates DRAM is not detected or fail.

VGA - indicates GPU is not detected or fail.

BOOT - indicates booting device is not detected or fail.

JRGB1: RGB LED strip connector

This connector allows you to connect the 5050 RGB LED strip.

Important

y

This connector supports 5050 RGB multi-color LED strips (12V/G/R/B) with the

maximum power rating of 3A (12V). Please keeping the LED strip shorter than 2

meters to prevent dimming.

y

Always turn off the power supply and unplug the power cord from the power outlet

before installing or removing the RGB LED strip.

y

Please use MSI󽶳s software to control the extended LED strip.

1

JRGB1

Extension cable (optional)

5050 LED strip

1

1 +12V 2 G

3 R 4 B

19

Overview of Components BIOS Setup

BIOS Setup

The default settings offer the optimal performance for system stability in normal

conditions. You should always keep the default settings to avoid possible system

damage or failure booting unless you are familiar with BIOS.

Important

y

BIOS items are continuous update for better system performance. Therefore, the

description may be slightly different from the latest BIOS and should be held for

reference only. You could also refer to the HELP information panel for BIOS item

description.

y

The pictures in this chapter are for reference only and may vary from the product

you purchased.

y

The BIOS items will vary with the processor.

Entering BIOS Setup

Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter Boot

Menu message appears on the screen during the boot process.

Function key

F1: General Help

F2: Add/ Remove a favorite item

F3: Enter Favorites menu

F4: Enter CPU Specifications menu

F5: Enter Memory-Z menu

F6: Load optimized defaults

F7: Switch between Advanced mode and EZ mode

F8: Load Overclocking Profile

F9: Save Overclocking Profile

F10: Save Change and Reset*

F12: Take a screenshot and save it to USB flash drive (FAT/ FAT32 format only).

* When you press F10, a confirmation window appears and it provides the

modification information. Select between Yes or No to confirm your choice.

20

BIOS Setup

Resetting BIOS

You might need to restore the default BIOS setting to solve certain problems. There

are several ways to reset BIOS:

y Go to BIOS and press F6 to load optimized defaults.

y Short the Clear CMOS jumper on the motherboard.

Important

Please refer to the Clear CMOS jumper section for resetting BIOS.

Updating BIOS

Updating BIOS with M-FLASH

Before updating:

Please download the latest BIOS file that matches your motherboard model from MSI

website. And then save the BIOS file into the USB flash drive.

Updating BIOS:

1. Press Del key to enter the BIOS Setup during POST.

2. Insert the USB flash drive that contains the update file into the computer.

3. Select the M-FLASH tab and click on Yes to reboot the system and enter the flash

mode.

4. Select a BIOS file to perform the BIOS update process.

5. After the flashing process is 100% completed, the system will reboot

automatically.

Updating the BIOS with Live Update 6

Before updating:

Make sure the LAN driver is already installed and the Internet connection is set

properly.

Updating BIOS:

1. Install and launch MSI LIVE UPDATE 6.

2. Select BIOS Update.

3. Click on Scan button.

4. Click on Download icon to download and install the latest BIOS file.

5. Click Next and choose In Windows mode. And then click Next and Start to start

updating BIOS.

6. After the flashing process is 100% completed, the system will restart

automatically.

ページが読み込まれています...

MSI B450PVDHMAX ユーザーマニュアル

MSI B450PVDHMAX ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント