Dell PowerEdge T605 クイックスタートガイド

Dell™ PowerEdge™

T605 Systems

Getting Started With

Your System

系统使用入门

はじめに

시스템시작하기

Dell™ PowerEdge™

T605 Systems

Getting Started With

Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; AMD and AMD Opteron

are registered trademarks of Advanced Micro Devices; Microsoft, Windows and Windows Server are

registered trademarks of Microsoft Corporation; Red Hat and Red Hat Enterprise Linux are registered

trademarks of Red Hat, Inc.; SUSE is a registered trademark of Novell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks

and trade names other than its own.

Model SCM

November 2007 P/N YY607 Rev. A00

Getting Started With Your System 3

System Features

This section describes the major hardware and software features of your

system. It also provides information about other documents you may

need when setting up your system and how to obtain technical assistance.

• One or two dual-core or quad-core AMD™ Opteron™ processors.

NOTE: Use the System Setup program to view processor information.

See the Hardware Owner’s Manual.

• A minimum of 1 GB (single-processor systems) or 2 GB (two-processor

systems) of 533 or 667 MHz registered parity DDR-II memory modules.

Memory is upgradable to a maximum of 32 GB (two-processor systems)

by installing combinations of 512-MB, 1-GB, 2-GB, or 4-GB memory

modules in the eight memory module sockets on the system board.

• Support for up to four 3.5-inch, internal non-hot-pluggable or hot-

pluggable (when available) Serial Attached SCSI (SAS) or SATA hard

drives. A controller expansion card is required for SAS hard drives or

for more than two SATA hard drives.

• One 3.5-inch peripheral drive bay for the optional diskette drive, and

two 5.25-inch bays for the following supported drives: DVD-ROM,

combination CD-RW/DVD, DVD+RW, or tape backup device.

NOTE: DVD devices are data only.

• An intrusion switch that signals the appropriate systems management

software if the cover is opened.

• A 650-W non-redundant power supply, or an optional hot-pluggable

675-W power supply in a 1 + 1 redundant configuration.

4 Getting Started With Your System

The system board includes the following integrated features:

• SATA controller that supports up to two cabled SATA hard drives,

and up to two of the following supported devices: DVD-ROM,

CD-RW/DVD combination drive, DVD+RW, or SATA tape

backup device.

NOTE: DVD devices are data only.

• One 133-MHz PCI-X expansion slot, three PCI Express (PCIe) x4

expansion slots, and one PCIe x8 expansion slot.

• An integrated ATI RN50 2D graphics controller with a minimum of 32 MB

of graphics memory. Maximum resolution is 1280 x 1024 with 65,536

colors; graphics are supported in the following resolutions: 640 x 480,

800 x 600, 1024 x 768, and 1280 x 1024.

• An integrated Gigabit NIC, capable of supporting 1000-Mbps, 100-Mbps,

or 10-Mbps data rates, with support for PXE, Wake-on-LAN, TCP/IP

Offload Engine (TOE), and iSCSI offload and boot.

• An integrated Trusted Platform Module (TPM) version 1.2 used for

security applications, capable of generating and storing keys and storing

passwords and digital certificates. (Not available in China.)

• Eight USB 2.0-compliant connectors (two on the front, one internal

for a bootable memory key, and five on the back) capable of supporting

a diskette drive, a DVD-ROM drive, a keyboard, a mouse, or a USB flash

drive.

• Optional Remote Access Controller (RAC) for remote systems

management.

• Standard Baseboard Management Controller (BMC) with serial

and LAN access.

• Back-panel connectors include serial, video, five USB connectors,

and one NIC connector.

• Front-panel connectors include two USB connectors.

• Front-panel LCD for system ID and error messaging.

For more information about specific features, see “Technical Specifications”

on page 10.

Getting Started With Your System 5

Supported Operating Systems

Your system supports the following operating systems:

• Microsoft

®

Windows Server

®

2008 Standard and Enterprise (32-bit x86)

Editions

• Microsoft Windows Server 2008 Standard and Enterprise (x64) Editions

• Microsoft Windows

®

Small Business Server 2008 Standard and Premium

Editions

• Microsoft Windows Server 2003 Standard and Enterprise (32-bit x86)

Editions with SP2

• Microsoft Windows Server 2003 Standard and Enterprise (x64) Editions

with SP2

• Microsoft Windows Server 2003 R2 Standard and Enterprise (32-bit x86)

Editions with SP2

• Microsoft Windows Server 2003 R2 Standard and Enterprise (x64)

Editions with SP2

• Microsoft Windows Small Business Server 2003 R2 Standard

and Premium Editions with SP2

•Red Hat

®

Enterprise Linux

®

ES and AS (version 4.5) (x86_32)

• Red Hat Enterprise Linux ES and AS (version 4.5) (x86_64)

• Red Hat Enterprise Linux Server 5 (x86_32)

• Red Hat Enterprise Linux Server 5 (x86_64)

•SUSE

®

Linux Enterprise Server 9 (SP4) (x86_64)

• SUSE Linux Enterprise Server 10 (x86_64)

NOTE: For the latest information on supported operating systems,

see www.dell.com.

6 Getting Started With Your System

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and

regulatory information. Warranty information may be included within this

document or as a separate document.

•The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install

or replace system components.

• CDs included with your system provide documentation and tools

for configuring and managing your system.

• Updates are sometimes included with the system to describe changes

to the system, software, and/or documentation.

NOTE: Always check for updates on support.dell.com and read the updates

first because they often supersede information in other documents.

• Release notes or readme files may be included to provide last-minute

updates to the system or documentation or advanced technical reference

material intended for experienced users or technicians.

• Operating system documentation describes how to install (if necessary),

configure, and use the operating system software.

• Documentation for any components you purchased separately provides

information to configure and install these options.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system

does not perform as expected, see your Hardware Owner’s Manual.

Dell Enterprise Training and Certification is available; see

www.dell.com/training for more information. This service may not be

offered in all locations.

Getting Started With Your System 7

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety

instructions and important regulatory information in your Product Information

Guide.

NOTICE: Make sure there are no physical obstructions within 30 cm (12 inches)

of the front of the system and 61 cm (24 inches) of the rear of the system.

This may cause a decrease in airflow, which could cause your system to overheat.

This section describes the steps to set up your system for the first time.

Unpack the System

Upack your system and identify each item. Keep all shipping materials in case

you need them later.

8 Getting Started With Your System

Connect the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which

cable to plug into each connector. Be sure to tighten the screws (if any)

on the monitor's cable connector.

Connect the System to Power

Connect the monitor’s power cable to the monitor (optional), and connect

the system’s power cable(s) to the system.

Getting Started With Your System 9

Installing the Power Cord Retention Bracket

Attach the power cord retention bracket on the right bend of the power

supply handle. Bend the system power cable into a loop as shown in the

illustration and attach to the bracket’s cable clasp. Repeat the procedure

for the second power supply.

Plug the other end of the power cable(s) into a grounded electrical outlet

or a separate power source such as an uninterrupted power supply (UPS)

or a power distribution unit (PDU).

Turn on the System and Monitor

Press the power button on the system and the monitor (optional). The power

indicators should light. Adjust the monitor's controls until the displayed

image is satisfactory.

10 Getting Started With Your System

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system

for the first time, see the Quick Installation Guide. Be sure the operating system

is installed before installing hardware or software not purchased with the

system.

Technical Specifications

Processor

Processor type One or two dual- or quad-core

AMD

™

Opteron

™

processors

Expansion Bus

Bus type PCIe and PCI-X

Expansion slots

PCIe

One x8 full-height, full-length 3.3-V

(slot 4)

Three x4 full-height, full-length 3.3-V

(slots 1 through 3)

PCI-X

One full-height, full-length 3.3-V (slot 5)

One internal USB key socket

Memory

Architecture

128-bit DDR II SDRAM DIMMs, rated

for

533-MHz or 667-MHz operation

Memory module sockets Eight 240-pin

Memory module capacities

512 MB, 1 GB, 2 GB, or 4 GB

Minimum RAM

1 GB (one processor) or 2 GB

(two processors)

Maximum RAM 16 GB (one processor) or 32 GB

(two processors)

Getting Started With Your System 11

Drives

Hard drives

Up to four 3.5-inch internal non-hot-plug

or hot-plug (when available) SAS or SATA

Diskette drive One optional internal 3.5-inch, 1.44-MB

Optical drives Up to two optional internal DVD-ROM

(SATA or PATA), DVD+RW (SATA or

PATA), or CD-RW/DVD combination

(SATA) drives

NOTE: DVD devices are data only.

External optional USB DVD

Tape drive One optional internal half-height,

5.25-inch SAS, SATA, or SCSI

External optional USB tape backup

device

Flash drive External optional USB

Internal optional USB

Connectors

Back

NIC

One RJ-45 (for Broadcom Gigabit LOM)

Serial

9-pin, DTE, 16550-compatible

USB

Five 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

One 4-pin, USB 2.0-compliant

12 Getting Started With Your System

Video

Video type Integrated

Video memory 32 MB (minimum)

Power

AC power supply

Wa tt ag e

650 W (non-redundant power supply)

675 W (redundant power supply)

Voltage 100-240VAC, 6.0-3.0A, 50/60 Hz

Heat dissipation

624 BTU/Hour (non-redundant

power supply)

574 BTU/Hour (redundant power supply)

CMOS backup battery CR 2032 3.0-V lithium ion coin cell

Physical

Height 456 mm (17.95 inches)

Width 210 mm (8.27 inches)

Depth 635 mm (25 inches)

Weight (maximum configuration) 27 kg (59.52 lb)

Getting Started With Your System 13

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F)

Storage

–40° to 65°C (–40° to 149°F)

Relative humidity

Operating

20% to 80% (noncondensing)

with a maximum humidity gradient

of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms, 5 to 350 Hz at 0.0002 G2/Hz

Storage

1.54 Grms, 10 to 250 Hz

at 0.003 to 0.01 G2/Hz

Maximum shock

Operating

27 G +/– 10% with pulse duration

of 2.6 msec +/– 10%

Storage

71 G +/– 10% with pulse duration

of 2 msec +/– 10%, 32G +/– 5% with

velocity change of 235 ips +/– 5%

Altitude

Operating

–15.2 to 3,048 m (–50 to 10,000 ft)

Storage

–15.2 to 10,600 m (–50 to 35,000 ft)

Airborne contaminant level

Class

G2 or lower as defined

by ISA-S71.04-1985

14 Getting Started With Your System

Dell

™

PowerEdge

™

T605

系统

系统使用入门

注、注意和警告

注： “注”表示可以帮助您更好地使用计算机的重要信息。

注意：“注意”表示可能会损坏硬件或导致数据丢失、并告诉您如

何避免此类问题。

警告：“警告”表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本说明文件中的信息如有更改、恕不另行通知。

未经

Dell Inc.

书面许可、严禁以任何形式进行复制。

本文中使用的商标：

Dell

和

DELL

徽标是

Dell Inc.

的商标；

AMD

和

AMD Opteron

是

Advanced

Micro Devices

的注册商标；

Microsoft

、

Windows

和

Windows Server

是

Microsoft Corporation

的

注册商标；

Red Hat

和

Red Hat Enterprise Linux

是

Red Hat, Inc.

的注册商标；

SUSE

是

Novell Inc.

的注册商标。

本说明文件中述及的其它商标和产品名称是指拥有相应商标和产品名称的公司或其制造的

产品。

Dell Inc.

对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。

型号

SCM

2007

年

11

月

P/N YY607 Rev. A00

系统使用入门 17

系统功能

本节介绍系统的主要硬件和软件功能。还介绍了有关在安装系统时可能需

要的其它说明文件的信息、以及如何获得技术帮助的信息。

•

一个或两个双核或四核

AMD

™

Opteron

™

处理器。

注：使用系统设置程序可以查看处理器信息。请参阅《硬件用户手册》。

•

至少

1 GB

（单处理器系统）或

2 GB

（双处理器系统）的

533

或

667 MHz

带寄存器的奇偶校验

DDR-II

内存模块。通过在系统板上的八个内存模

块插槽中安装

512 MB

、

1 GB

、

2 GB

或

4 GB

内存模块组合、可将内存升

级到最大

32 GB

（双处理器系统）。

•

支持多达四个

3.5

英寸、内部非热插拔或热插拔（当可用时）、串行连接

的

SCSI (SAS)

或

SATA

硬盘驱动器。

SAS

硬盘驱动器或两个以上的

SATA

硬盘驱动器将需要控制器扩充卡。

•

一个

3.5

英寸外围设备驱动器托架、用于可选的软盘驱动器；两个

5.25

英寸托架、用于以下支持的驱动器：

DVD-ROM

、组合

CD-RW/DVD

、

DVD+RW

或磁带备份设备。

注：

DVD

设备仅用于数据。

•

防盗开关、在机盖被打开时会向相应的系统管理软件发送信号。

•

一个

650 W

非冗余电源设备、或一个可选的热插拔

675 W

电源设备

（在

1 + 1

冗余配置中）。

系统板包括以下集成功能：

•

SATA

控制器、支持多达两个已连线的

SATA

硬盘驱动器、并支持

多达两个以下支持的设备：

DVD-ROM

、

CD-RW/DVD

组合驱动器、

DVD+RW

或

SATA

磁带备份设备。

注：

DVD

设备仅用于数据。

•

一个

133-MHz PCI-X

扩充槽、三个

PCI Express (PCIe) x4

扩充槽和

一个

PCIe x8

扩充槽。

•

一个带有最低

32 MB

图形内存的集成

ATI RN50 2D

图形控制器。

使用

65,536

色时最大分辨率为

1280 x 1024

；支持以下分辨率的图形：

640 x 480

、

800 x 600

、

1024 x 768

和

1280 x 1024

。

18 系统使用入门

•

一个集成的千兆位

NIC

、可支持

1000 Mbps

、

100 Mbps

或

10 Mbps

数

据速率、并支持

PXE

和通过

LAN

唤醒、

TCP/IP

卸载引擎

(TOE)

以及

iSCSI

卸载和引导。

•

一个集成的受信任平台模块

(TPM) 1.2

版、用于安全保护应用程序、

可支持生成和存储密钥以及存储密码和数字证书

（在中国未提供此

功能）。

•

八个

USB 2.0

兼容连接器（两个在正面、一个在内部用于可引导存储钥

匙以及五个在背面）、可支持软盘驱动器、

DVD-ROM

驱动器、键盘、

鼠标或

USB

快擦写驱动器。

•

可选的远程访问控制器

(RAC)

、用于远程系统管理。

•

标准底板管理控制器

(BMC)

、支持串行访问和

LAN

访问。

•

背面板连接器、包括串行连接器、视频连接器、五个

USB

连接器和

一个

NIC

连接器。

•

前面板连接器、包括两个

USB

连接器。

•

前面板

LCD

显示屏、用于显示系统

ID

和错误信息。

有关特定配置的详情、请参阅第

23

页上的“技术规格”。

支持的操作系统

您的系统支持以下操作系统：

•

Microsoft

®

Windows Server

®

2008

标准版和企业版

(32-bit x86)

•

Microsoft Windows Server 2008

标准版和企业版

(x64)

•

Microsoft Windows

®

Small Business Server 2008

标准版和高级版

•

Microsoft Windows Server 2003

标准版和企业版

(32-bit x86)

（含

SP2

）

•

Microsoft Windows Server 2003

标准版和企业版

(x64)

（含

SP2

）

•

Microsoft Windows Server 2003 R2

标准版和企业版

(32-bit x86)

（含

SP2

）

•

Microsoft Windows Server 2003 R2

标准版和企业版

(x64)

（含

SP2

）

ページが読み込まれています...

Dell PowerEdge T605 クイックスタートガイド

Dell PowerEdge T605 クイックスタートガイド

他の言語で

関連論文

その他のドキュメント