青萍科技
Goose 说明书（T版）
2.0
20220429
张思垚
青萍科技图纸标注
青萍科技图纸标注
PANTONE Cool Gray 11C
1. 未经授权的维修、 误用、 碰撞、 疏忽、 滥用、 进液、 事故、 改动、 不正确的
使用非本产品配件；
2. 撕毁、 涂改标贴、 防伪标记等行为；
3. 已超过保修期；
4. 因不可抗拒力造成的损坏；
5. 不符合 《产品性能故障表》 所列性能故障的情况；
6. 因人为原因导致本产品及其配件产生 《产品性能故障表》 所列性能故障。
在青萍科技（北京）有限公司设立了分支机构或售后服务中心的国家或地
区 ， 我们为当地销售的青萍蓝牙温湿度计 T 提供一年有限保修服务。 保修
服务条款包括:
1. 自顾客签收之日起 7 天内， 如本产品出现“产品性能故障表”中所列的故
障， 经我们的售后服务部门确认后， 顾客可免费获得退款或换货服务。
2. 从顾客签收之日起第 8 天到第 15 天 ， 如本产品出现“产品性能故障表中
所列的故障， 经我们的售后服务部门确认后， 顾客可免费获得换货或维
修服务。
3. 自顾客签收之日起 12 个月内， 如本产品出现“产品性能故障表中所列的
故障， 经我们的售后服务部门确认后， 顾客可免费获 得维修服务。
在青萍科技（北京）有限公司尚未设立分公司或售后服务中心的国家或地
区， 如有质量问题， 请联系当地销售方。
欢迎使用青萍蓝牙温湿度计 T 。
桌面模式
青萍蓝牙温湿度计 T 可以放在桌面上使用。
注意事项
请勿堵塞本产品底部的通气孔。
本产品无防水、 防尘功能。
请勿长期在湿度高于 90% 的环境下使用。
请勿将电池或装有电池的本产品投入火中， 以免引起爆炸。
请勿私自拆解本产品， 以免受伤。
将后盖掀开一半（与机身呈 45° 夹角）， 即可将青萍蓝牙温湿度计 T 平稳放
置在桌面：
墙面模式
青萍蓝牙温湿度计 T 可以和墙贴配合， 贴在墙上使用。
切换温度单位
青萍蓝牙温湿度计 T 屏幕显示的温度单位可在摄氏度（℃）和华氏度（℉）
之间切换。
短按机身背面的按钮即可切换：
错误代码 产品中有害物质的名称及含量 产品性能故障表 保修说明 非保修条例
连接“家庭”
屏幕显示内容不完整， 或无法显示内容
按钮无响应
传感器无法正常工作
包装内有一枚墙贴， 墙贴背面粘有双面胶：
当屏幕不显示内容时， 请更换电池。
* 取下电池后， 屏幕上可能仍然显示内容， 这是正常的。 本产品的屏幕是电
子墨水屏， 在不供电的情况下屏幕内容可保持一段时间。
撕下双面胶覆膜， 将墙贴粘在选好的位置， 然后吸附青萍蓝牙温湿度计 T：* 请避免将本产品放在绒面或有凸起颗粒的表面上， 以免产品底部的通气
孔被堵塞， 导致测量不准。
青萍科技（北京）有限公司
地址： 北京市朝阳区望京东园四区 7 号楼 17 层 1706 室
网址： qingping.co
电话： 400 697 2778
邮箱： k[email protected]
您可在 iOS 或 iPadOS 设备上打开“家庭” app ， 点击“+”， 选择“添加或扫
描配件”， 然后扫描本产品背面的二维码， 将本产品连接至“家庭”。
* 如果添加不成功， 可将本产品恢复出厂设置后再试。 方法详见本产品“恢
复出厂设置”部分的说明。
* 远程查看此 HomeKit 配件的读数或设置与其他配件的联动，需先将
HomePod、 Apple TV 或 iPad 设置为 home hub。 建议您更新到最新的软件
和操作系统。
连接“青萍+”
您也可使用“青萍+”手机 app 来连接本产品， 进行查看读数、 读取历史数
据、升级固件等操作。
“青萍+” 的下载地址是 qingping.co/plus， 您也可扫描下方的二维码来下
载：
安装 app 后， 请在 app 内添加设备， 选择“青萍蓝牙温湿度计 T ”， 然后根
据提示操作。
* 如果您已在“家庭” app 中添加了本产品， 那么本产品会自动出现在“青
萍 + ” app 中， 无需再次添加。
* 打开“青萍+” app 并通过蓝牙连接青萍蓝牙温湿度计 T 后， 将自动同步最
近 30 天的历史数据， 过程中请保持蓝牙连接畅通。
* 本产品不支持 Android 设备。
基本参数
检测项目
温度
湿度
0 ~ 50℃
0 ~ 99.9%
量程
检测项目和量程
人体感受到的温度取决于多项因素， 例如气温、 热辐射、 相对湿度、 风速、
人体活动和健康状况、 着装等。 其中温度和相对湿度是影响人体舒适度的
两个重要因素。 冬季， 温度在 20°C~24°C、湿度在 30%~60% 时， 人体感觉
较为舒适； 夏季， 温度在 23°C~26°C、 湿度在 25%~60% 时， 人体感觉较
为舒适。
常见问题
屏幕显示的错误代码 含义
超出量程
传感器故障
E1
E2
产品型号： CGG1T
产品重量： 59 克
产品尺寸： 直径 74 毫米， 厚度 14 毫米
屏幕尺寸： 直径 55 毫米
无线网络： 蓝牙 5.0
电池类型： CR2430 纽扣电池
CMIIT ID： 2020DP5346
部件名称
壳体
墙托
显示屏
电路板
电池
有害物质
铅
(Pb)
O
O
O
O
汞
(Hg)
O
O
O
镉
(Cd)
O
O
O
六价铬
(Cr(VI))
O
O
O
多溴联苯
(PBB)
O
O
O
多溴二苯醚
(PBDE)
O
O O O O O
O
O
O O O O O O
本表格依据 SJ/ T 11364 的规定编制。
O: 表示该有害物质在该部件所有均质材料中的含量均在
GB/T 26572-2011 规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量
超出GB/T 26572-2011 规定的限量要求。
屏幕偶尔
变黑， 之后
又恢复正常
问题 解决办法
本产品的屏幕是电子墨水屏， 在局部刷新
若干次之后， 需要全局刷新一次。 局部刷
新时， 屏幕不会全部变黑， 全局刷新时，屏
幕会全部变黑， 然后在 1 秒内恢复正常。
请检查是否已根据本说明书第 1 页的介绍
启用产品。 如已启用， 则请尝试更换电池。
电池类型为纽扣电池， 型号为 CR2430。
本产品的屏幕是电子墨水屏， 在不供电的
情况下屏幕内容可保持一段时间。
屏幕不显示
内容
电池取下后
屏幕仍显示
内容
1. 当所处环境发生急剧变化时， 例如刚刚从
室外移动到室内时， 本产品需要 10 分钟
左右来让读数贴近新环境的实际情况。
2. 手持本产品时， 人体的温度会对读数有影
响， 导致读数和环境实际情况有差异。
3. 请检查本产品底部的通气孔是否被堵塞。
如被堵塞， 请小心清理， 以免损坏传感器。
读数不准
问题 解决办法
温度超出传感器量程。 请将产品放在正常
室温环境下静置 10 分钟。
屏幕显示 E1
Attention
Error Codes Performance Faults Warranty FCC STATEMENT :Non-warranty
The content displayed on the screen is incomplete or the
screen cannot display content.
No response when the button is pressed.
The sensor is not working properly.
1. Unauthorized repair, misuse, collision, negligence, abuse, liquid injection,
accident, alteration, improper use of accessories not originally supplied with
this product.
2. The warranty period has expired.
3. Damage caused by force majeure.
4. The situation does not meet the fault listed in the Performance Faults.
Qingping Technology (Beijing) Co., Ltd.
Address: Room 2006, Block B, Greenland Center, Wangjing,
Chaoyang District, Beijing 100102, China
Website: qingping.co
Email: [email protected]
Specifications
Item
Temperature
Humidity
0~50℃
(32~122℉)
0 ~ 99.9%RH
Range
Measuring Items and Ranges
The temperature that a human body perceives depends on many factors such as
air temperature, relative humidity, wind velocity, physical activity and condition,
or even the clothes worn.
In winter, the human body feels the most comfortable when the temperature is
between 20℃~24℃ while RH is between 30%~60%; in summer, the range is
respectively 23℃~26℃ and 25%~60%.
Question/
Problem Answer/Solution Question/
Problem Answer/Solution
Please check if the isulating sheet has been
removed according to the instructions on
page 1 of this manual. If it is removed
already, please try replacing the battery. The
battery type is button battery CR2430.
The screen
doesn’t show
anything.
The screen still
displays readings
after the battery
is removed.
The product uses an e-ink screen that keeps
display the content for a while after the
battery is removed.
FAQ
Question/
Problem Answer/Solution
1. When the environment changes drastically,
for example, after just moved from outdoor
to indoors, it needs about 10 minutes for
the readings to approach the actual values
of the new environment.
2. When the product is held in hand, the
temperature of the human body will effect
the readings,resulting in difference between
the readings and the actual values of the
environment.
3. Check if the vent hole at the bottom of the
product is clogged. If it is clogged, please
clean it carefully, and avoid damaging the
sensor.
Readings
inaccurate. The product uses an e-ink screen, which
needs to be completely refreshed after
being partly refreshed several times. When
it's being completely refreshed, the screen
will turn to black and then return to normal
immediately.
The screen turns
black occasionally
and then returns
to normal.
The environment temperature exceeded the
measurement range of the product. Please
put the product in a normal indoor
environment.
E1 shows
on the screen.
Model: CGG1T
Weight: 59 g
Size: Diameter 74 mm, thickness 14 mm
Screen Size: Diameter 55 mm
Wireless Connectivity: Bluetooth 5.0
Battery Type: CR2430 button cell
Do not block the vent hole on the bottom of the product.
This product is not waterproof or dustproof.
Do not use in an environment with humidity greater than 90% for a long time.
Do not throw the battery or the product with the battery into the fire to avoid
an explosion.
Do not disassemble the product by yourself to avoid injury.
In the countries and regions where Qingping Technology (Beijing) Co., Ltd. has
established branches or after-sales service centers, we provide a 1-year limited
warranty service for the locally sold Qingping Temp & RH Monitor T . The
warranty service terms are:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures: Reorient or relocate the receiving antenna. Increase the
separation between the equipment and receiver. Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected. Consult
the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
1. Within 7 days from the date of the receipt, if the product has faults that listed
in the “Performance Faults”, after the faults are confirmed by our after-sales
service department, the customer can have the refund or exchange the
product for free.
2. From the 8th to the 15th day after the receipt, if the product has faults that
listed in the “Performance Faults”, after the faults are confirmed by our
after-sales service department, the customer can have a replacement or
repair service for free.
3. Within 12 months from the date of receipt, if the product has faults that listed
in the “Performance Faults”, after the faults are confirmed by our after-sales
service department, the customer can have the maintenance service for free.
The environment temperature exceeded
the measurement rangeof the product.
The sensor is malfunctioning.
E1
E2
Error Code
on the Screen Meaning/Solution
Thank you for using Qingping Temp & RH Monitor T .
Desktop Mode
Qingping Temp & RH Monitor T can be placed on desktops to use.
By opening the back cover halfway (at an angle of 45° to the body), the Qingping
Temp & RH Monitor T can be placed on the desktop:
Wall Mode
Qingping Temp & RH Monitor T can be used with its wall stickers and attached
to a wall.
Switch the Temperature Unit
The temperature unit displayed on Qingping Temperature & RH Monitor screen
can be switched between Celsius (℃) and Fahrenheit (℉).
Press the button on the back of the product to switch:
* To control the accessory through Home app automatically or remotely, you
have to set up your HomePod, Apple TV, or iPad as a home hub. It is
recommended that you update to the latest software and operating system.
There is a wall sticker in the package, and the double-sided tap is stuck on the
back of it:
If the screen doesn’t display anything, the battery needs to be replaced.
Remove the film of the double-sided tape, stick the wall sticker to your selected
position, and then attach the Qingping Temp & RH Monitor T :
* Please avoid placing the product on surfaces of suede or raised particles to
prevent the vent hole at the bottom of the product from being clogged and
resulting in inaccurate measurement.
45°
45°
Fully open the back cover (at an angle of 90° to the body), and then hold the
battery cover with both thumbs and push it counterclockwise to unscrew the
battery cover:
Connect to “Qingping+”
After installing the app, please open it and add a device, select “Qingping Temp &
RH Monitor T ”, and then follow the instructions the app shows.
* If you have added your Qingping Temp & RH Monitor T in Home app, then it
will appear in Qingping+ app automatically, no need to add again.
* While Qingping+ app is opened and connected to your Qingping Temp & RH
Monitor T , it will sync the 30-day historical data automatically, please keep the
Bluetooth connection during the process.
* This product doesn’t support connecting to Android devices.
You can also use the mobile app “Qingping+” to connect Qingping Temp & RH
Monitor T , to view the readings, access the historical data, and upgrade the
firmware, etc.
You can visit qingping.co/plus or scan the QR code below to download the app:
Connect to “Home”
Open the Home app on your iOS or iPadOS device, and tap “+”, then select “Add or
Scan Accessory”, follow the instruction to add your Qingping Temp & RH Monitor
T .
* If failed to add, please reset the Qingping Temp & RH Monitor T and try again.
Please refer to “Reset Factory Settings” of this manual.
HomeKit and iPad are trademarks of Apple Inc., registered in
the U.S. and other countries.
HomeKit 和 iPad 是 Apple Inc. 注册于美国和其他国家的商标。
1 2 34 7 8
910
56
11 12 13 14 17 18
19 2221
15 16
23 24 25 26
29 30 31 32
27 28
33 34 3735 36
蓝牙温湿度计 T 版
Temp & RH Monitor T Version
User Manual
说明书
Insert or Replace Battery
Qingping Temp & RH Monitor T uses a CR2430 button cell.
In countries or regions where Qingping Technology (Beijing) Co., Ltd. has not
established a branch or after-sales service center, please contact the local seller
if you have any quality problems.
* After removing the battery, the content may still be displayed on the screen, it’s
normal. The product uses an e-ink screen, the content displayed on it can be
kept for a while without power supply. Restore Factory Settings
Press and hold the key on the back of the product, and release after the screen
displays “188”, and then wait for the product return to display correct
temperature and humidity readings, which means that the restoration of factory
settings has been completed.
放入或更换电池
青萍蓝牙温湿度计 T 使用型号为 CR2430 的纽扣电池。
完全掀开后盖（与机身呈 90° 夹角）， 然后用双手大拇指按住电池盖， 逆时
针搓动， 即可拧下电池盖:
恢复出厂设置
按住本产品背部的按键， 在屏幕显示“188”后松手， 等候屏幕恢复正常显示
温湿度， 即完成恢复出厂设置。
封面封底 1‒2 3‒4 5‒6 7‒8
11‒12
9‒10 13‒14 15‒16 17‒18
21‒22
19‒20 23‒24 25‒26 27‒28
31‒32
29‒30 33‒34 35‒36 37‒38
-
1
