Flashforge Adventurer 4 Pro ユーザーマニュアル

用户使用手册

Adventurer 4 Pro / 冒险家4 Pro

User Guide

EN/CN-A04

中文P32

本手册仅适用于闪铸科技冒险家4 Pro 3D打印机

This guide is only applicable to FLASHFORGE Adventurer 4 Pro 3D printer.

Scan the QR code to view the unboxing

video, which is also accessible on the

USB ﬂash drive.

扫码观看开箱视频

或打开U盘观看

CONTENTS

Notice

Parameters

Chapter 1 Adventurer 4 Pro

1.1 - Component Introduction

1.2 - Packing List

Chapter 2 Unpacking

Chapter 3 Software Installation

Chapter 4 Equipment Preparation

Chapter 5 First Printing

Chapter 6 User Interface Introduction

Chapter 7 Q&A

Chapter 8 Help and Support

06

07

02

05

06

08

09

10

14

17

25

31

17

19

20

21

22

23

24

01

6.1 - Build

6.2 - Prepare

6.2.1 - Preheat

6.2.2 - Filament

6.3 - Settings

6.4 - Maintain

6.4.1 - Upgrade

6.4.2 - Log

6.4.3 - Calibration

6.4.4 - Change Extruder

6.4.5 - Maintain

Notice

Safety Notice: please read and strictly follow all the

safety warnings and notice below.

Work Environment Safety

Keep your work place tidy.

Do not operate the device in the presence of flammable liquids, gases or dust.

The high temperature generated by equipment operation may react with

combustible gases, liquids, and airborne dust, thus causing fire.

Keep the device out of children's and untrained people's reach.

Electrical Safety

02

Note: Every printer has been tested before leaving the factory. If there are some ﬁlament

residues in the extruder or some tiny scratches on the build plate, it is normal and

won’t aﬀect the printing quality.

Always use the device with a properly grounded outlet. Do not reﬁt the device's plug.

Ungrounded / improperly grounded / reﬁtted plugs will increase the risk of leakage

of electricity.

Do not expose the device to damp or hot-sun environment. Humidity will increase the

risk of electric leakage. Exposure to sunlight will accelerate the aging of plastic parts.

In case of device damage, please use the power cord provided by Flashforge.

Avoid using the device during a thunderstorm.

In case of uncertain accidents, please unplug the device if you do not use it for long.

When grounding, plug the power cord into the three-in-one socket and connect to the

external grounding wire through the grounding terminal of the three-in-one socket.

Check and replace the fuse: To prevent electric shock, please be sure to turn oﬀ the

power switch and unplug the power cord before checking or replacing the fuse.

Replace the fuse: Open the fuse box of the three-in-one socket and replace the fuse

with the fuse of 5*20, T10AL250V speciﬁcation.

03

Environment Requirements

Placement Requirements

The device must be placed in a dry and ventilated environment. The distance of

the left, right and back side space should be at least 20cm, and the distance of the

front side space should be at least 35cm. Device storage temperature: RT 0-40℃.

Temperature: RT 15-30℃; moisture: 20%-70%.

Cautions

Keep the inside of the device clean and tidy. Do not place metal objects into the

chute at the bottom of the platform.

Please clean up the filament debris in time. It is recommended to operate this

outside the equipment.

Any modifications to the device will invalidate the guarantee.

Lower the build plate before loading/unloading filament. The distance between

the nozzle and build plate should be kept for at least 50mm.

Operate the device in a well-ventilated environment.

Never use the device for illegal activities.

Never use the device to make any food containers.

Never put the prints into your mouth.

Personal Safety

Do not touch the nozzle and build plate during printing.

Do not touch the nozzle and plate after printing to avoid high-temperature scalds

or mechanical damage!

Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts.

Do not operate the device while you are tired or under the influence of drugs,

alcohol or medication.

Hot surface

Do not touch

Warning crushing

of hands

Keep this area

clear

Keep body parts away

from moving parts

04

Legal Notice

All the information in this document is subject to any amendment or change

without the official authorization from Flashforge.

FLASHFORGE MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS

DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

FCC Notice

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: [1] This device may not cause harmful interference,

and [2] this device must accept any interference received, including

interference that may cause undesired operation.

Flashforge shall not be liable for errors contained herein for incidental

consequential damages in connection with furnishing, performance or use of

this material.

This document contains proprietary information protected by copyright.

Reserved.

Filament Requirements

Filament Storage

It’s recommended to use the filaments offered by Flashforge, or from the brands

accepted by Flashforge. Due to the different properties of filaments, you need to

modify printing parameters when using those which are not offered by Flashforge.

All polymers degrade with time. Do not unpack filament until necessary. Filament

should be stored in a dry and dust-free environment.

Name

Extruder quantity

Printing precision

Positioning precision

Layer thickness

Build volume

Nozzle diameter

Printing speed

Highest extruder

temperature

Supported filament

Power supply

Device size

Connectivity

Filament run-out reminder

Build plate

Remote camera monitoring

HEPA 13 Air filter

Adventurer 4 Pro

1

±0.1 mm

(test of a 100mm cube)

X/Y-axis：0.011 mm；

Z-axis：0.0025 mm

0.1~0.4 mm

220 x 200 x 250 mm

0.4(default)

0.6/0.3 mm(optional)

10~300mm/s

265℃

ABS/PLA/PETG/PLA-CF/PETG-CF

AC100-240V/DC 24V/

13.3A,320W

500(L)*470(W)*550(H)mm

USB / Wi-Fi/ Ethernet

√

PEI flexible steel platform

√

Parameters

05

Chapter 1 Adventurer 4 Pro

5. Filament intake cover

7. Platform base

9. Touch screen

4. Spool holder

1. Power switch

2. Power socket

8. Build plate

6. Front cover

20. Camera

13. Filament guide tube joint

15. Fan for cooling the extruder

11. Ethernet input

12. Extruder

10. USB

16. Fan for cooling the model

21. Air filter

17. Buckle 18. Air duct

3. Filament cover

19. Nozzle

14. Cable slot

21

1.1 Component Introduction

06

1

2

3

4

5

9

10

78

6

11

12

20

13

14

15

16

17

18

19

3D Printer Filament After-Sales

Service Card

Screwdriver

0.6-265 Nozzle

User Guide Unclogging

Pin Tool

Power Cable

Grease

Allen Wrench

Glue Stick

Filament Guide

Tube Joint

Leveling Card

USB Flash Drive

1.2 Packing List

07

1. Open the carton. 2. Take out the top foam box, power

cord, after-sales service card, user

guide and USB flash drive.

3. Take out the printer from the carton,

and remove the bubble wrap around

the printer. Tear off the fixing tapes

and the front door protective bag.

4. Open the front door of the printer

and take out the EPE foam filled

inside and filament.

08

Chapter 2 Unpacking

5. Take out the printer from the carton,

and remove the bubble wrap around

the printer. Tear off the fixing tapes

and the front door protective bag.

6. Open the side door of the printer and the cover above the filament chamber,

take out the EPE foam filled inside, and unpacking is finished.

09

Find the FlashPrint installation package in the USB flash drive and select the

version corresponding to your system to install.

Or you can download it from https://www.flashforge.com/download-center.

Chapter 3 Software Installation

Note

3D printing process is as follows:

(1). Obtain the 3D file;

(2). Download and install the slicing software;

(3). Prepare the equipment; (leveling, calibration and filament loading);

(4). Start printing (model file slicing, transmission and printing).

10

Note

The equipment has been leveled and calibrated before

delivery, but due to transportation or other influences,

the distance between the nozzle and platform may change.

It is recommended to conduct [Calibration] after unpacking.

1. Click [Maintain] - [Calibration] - [Normal Mode] to start pre-calibration.

The first point is to calibrate the initial distance between the extruder and the

platform. Click the Up and Down arrows to adjust the Z-axis deviation value;

Insert a leveling card between the nozzle and the platform. If it cannot be inserted,

it means that the nozzle and the platform are too close. Click the Up arrow to make

the nozzle away from the platform.

1/30

30

Leveling and calibration

Chapter 4 Equipment Preparation

Power Switch

Connect to power

Connect the cable to the printer,

turn on the switch and the screen

lights up.

11

2. Insert and slide the leveling card. If there is no frictional resistance, click the

Down arrow to make the nozzle closer to the platform; When there is slight friction

resistance, it means that the distance is appropriate.

3. After calibrating the first point,

please follow the on-screen

prompts to continue the 30-point

automatic leveling.

1/30

30

For specific operation, you can refer to the video.

The link path is as follows:

Flashforge's Official Website - Support - Video Center - select

[Operation Videos] - [Adventurer 4 Pro]

Scan the QR code to

view the video.

12

Mind the loading direction of filament. Make sure it is clockwise as the

picture shows. If the filament is loose, please arrange it according to the

filament extrusion direction and then put it back on the spool holder.

2. Put the spool of ﬁlament on the spool holder and close the ﬁlament cover.

Note

Filament Loading

1. Open the ﬁlament cover on the right side, insert the ﬁlament into

the ﬁlament intake, and push the ﬁlament into the feeding wheel

until some resistance is sensed.

Please make sure the ﬁlament is inserted into the

feeding wheels！

13

3. Tap [Prepare] - [Filament] - [Load]. Follow the instructions. Filament coming out of the

nozzle indicates a successful ﬁlament loading.

14

Chapter 5 First Printing

IP Address

IP Port：

192 . . . :168 2122 8899

Auto-scan

Connection

Connect

Note

Method 1: Printing from Local Files or from USB

You can print models from a USB ﬂash drive. Save the sliced ﬁle into a USB ﬂash drive,

insert it into the printer and select the corresponding ﬁle to print. The [Local Files] in the

printer or the USB ﬂash drive delivered randomly contains sliced test ﬁles, which can be

directly used to complete the ﬁrst printing.

1. Model Printing

Method 2: Printing via Wi-Fi Transmission

(1). Tap [Settings]-[Network]-[WIFI], and operate according to the instruction. Open FlashPrint,

click [Print], then click [Machine Type], and select [Adventurer 4 Pro]. You can try to enter

the IP address or scan it automatically. The IP address can be viewed in [Settings] - [About].

When the user wants to

use the browser to view

images, the printer and PC

connected networks must be in

the same network segment,

(that is, the printer and PC

should connect to the same

router).

15

（2）Click [My Printer] - [Add Printer].

Fill in the registration number (Registration Code) on the page and name the

printer. After clicking OK, the information will appear in the FlashCloud interface of

the printer.

FlashCloud

Home

My Printer

My Model

My Job

Model Library

My Printer The current printer is empty, please add a printer

Name Registration Code Type

Cn

+Add Printer

Add Printer

Name

All ﬁelds must be ﬁlled in

Registration Code

OK Cancel

Method 3: Cloud Printing

FlashCloud

（1）Open the FlashCloud website (https:cloud.sz3dp.com) to register an account.

After completing the activation via email, log in FlashCloud with your account.

Adventurer 4 Pro - 0.6

(2). Import the stl or obj ﬁle into the slicer; After ﬁnishing slicing and sending the ﬁle to

the printer, the printer will heat up and start printing automatically.

16

Polar Cloud

Register the Polar Cloud account at https://Polar3d.com.

2.Model Removal

Note

The nozzle and build plate are still hot after finishing printing. Please wait for

them to cool down before conducting operation.

The back side of the build plate is designed exclusively for PETG. Please use the

back when printing with PETG.

Please remove models after the platform has cooled down. If models are removd

when the platform is not completely cooled down, bubbles will occur on the

surface of the platform.

It is recommended to take the platform to the outside of the equipment for model

removal, otherwise the model debris will remain in the equipment. Please keep

the inside of the printer clean.

Adventurer 4 Pro: Take out the removable build plate, and bend the plate to get the

model. When printing for the second time, please ensure that there is no residual

ﬁlament on the platform.

After logging into your account, click the icon on the top right corner and click [Settings].

Find the PIN Code in the page. Turn on the Polar Cloud switch and enter the account and

PIN code after connecting Adventurer 4 Pro to network.

1. Click [Build], and then choose

the path to read the print ﬁle.

The interface layout may change whenever there is an upgrade of

firmware. The functions below are only for demonstration purposes.

2. File list

Chapter 6 User Interface Introduction

6.1 Build

Note

The ﬁnished prints will be marked.

17

Read the print ﬁle from the

local memory card

Tap a model ﬁle: For ﬁle details.

Long press a model ﬁle: To enable the multi-selection mode.

Read the print ﬁle from the

USB stick

Details

Extruder temperature

Time used

Speed

Copy the ﬁle to the

local memory card

Amount and type of

ﬁlaments required

Build plate temperature

Pause/Resume printing

Interface

Z：Used when the distance needs to be adjusted between the first printed layer and

the extruder. The up and down arrows indicate that the extruder moves upward or

downward.

Filament: Adjust the amount of filament extrusion during printing.

Fan：Adjust the fan speed.

Click OK to save and apply the changed parameters.

Layer thickness

Check more parameter settings and details

More Settings

Change the ﬁlament.

LED light switch

Adjust printing parameters:

extruder temperature/

platform temperature/

printing speed

18

ページが読み込まれています...

Flashforge Adventurer 4 Pro ユーザーマニュアル

Flashforge Adventurer 4 Pro ユーザーマニュアル

他の言語で