ENGLISH
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benet from the support that
Philips offers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Cutting element
2 On/off button
3 Zoom wheel
4 Handle
5 Charging light
6 Socket for appliance plug
7 Small comb
8 Large comb
9 Barber comb (QC5390/80 only)
10 Scissors (QC5390/80 only)
11 Adapter
12 Appliance plug
13 Pouch (QC5390/80 only)
14 Cleaning brush
Important
Read this user manual carefully before you use
the appliance and save it for future reference.
Danger
- Make sure the adapter does not get wet (Fig. 2).
Warning
- Check if the voltage indicated on the adapter
corresponds to the local mains voltage before
you connect the appliance.
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
- This appliance is not intended for use by
children. Children should be supervised
to ensure that they do not play with the
appliance.
- Always check the appliance before you use it.
Do not use the appliance if it is damaged,
as this may cause injury.
Caution
- Only use the adapter supplied to charge
the appliance.
- Use, charge and store the appliance at a
temperature between 5°C and 35°C.
- If the adapter is damaged, always have it
replaced with one of the original type in order
to avoid a hazard.
- If the appliance is subjected to a major change
in temperature, pressure or humidity, let the
appliance acclimatise for 30 minutes before
you use it.
- Do not use the appliance if any of its parts is
damaged or broken, as this may cause injury.
Compliance with standards
- This Philips appliance complies with all
standards regarding electromagnetic elds
(EMF). If handled properly and according to the
instructions in this user manual, the appliance
is safe to use based on scientic evidence
available today.
Preparing for use
Note: You can also use the appliance directly from
the mains when the battery is empty.
Charging
Charge the appliance for at least 1 hour before
you use it for the rst time and after a long period
of non-use.
When the appliance is fully charged, it has a
cordless operating time of up to 60 minutes.
When the charging light lights up orange, the
battery is running low (approx. 10 minutes of
operating time left) and you need to recharge
the appliance.
1 Make sure the appliance is switched off.
2 Insert the appliance plug into the socket of
the appliance and put the adapter in the wall
socket (Fig. 3).
, The charging light starts ashing green to
indicate that the appliance is charging.
, When the batteries are fully charged, the
charging light lights up green continuously.
After 30 minutes the charging light goes out
to save energy.
Using the appliance
Clipping with comb
The appliance comes with 2 combs for different
hair lengths.
The hair length settings are indicated in millimetres
on the comb. The settings correspond to the
remaining hair length after clipping.
23/01/2013
4222.002.8369.1
QC5390
Register your product and get support at
www.philips.com/welcome
1
2 3 4
42
39
36
5 6 7
8 9 10
11 12 13
1 Select the comb you want to use.
The small comb cuts the hair to a length of 3mm
to 22mm.
The large comb cuts the hair to a length of 23mm
to 42mm.
2 Slide the comb straight into the guiding
grooves on both sides of the handle
(‘click’) (Fig. 4).
3 To set the comb to the desired setting, turn
te zoom wheel to the desired hair length
setting (Fig. 5).
, The display on front of the appliance shows
the selected hair length in millimetres after
cutting.
, After 8 seconds, the display goes out to save
energy. To activate the display again, turn the
zoom wheel or press the on/off button.
Tip: Write down the hair length settings you selected
to create a certain hairstyle as a reminder for future
clipping sessions.
4 Press the on/off button to switch on the
appliance (Fig. 6).
5 Move the appliance through the hair slowly.
Tips
- To clip most effectively, move the appliance
against the hair growth direction.
- Since all hair does not grow in the same
direction, you need to move the appliance
in different directions (upwards, downwards
and across).
- Make sure that the at part of the comb is
always fully in contact with the scalp to obtain
an even result (Fig. 7).
- Make overlapping passes over the head to
ensure that you cut all the hair that needs to
be cut.
6 Regularly remove cut hair from the comb.
If a lot of hair has accumulated in the comb,
remove the comb from the appliance and blow
and/or shake the hair out of it.
Contouring without comb
You can use the appliance without comb to clip
hair very close to the skin (0.5mm) or to contour
the neckline and the area around the ears.
Be careful when you clip without comb because
the cutting element removes every hair it touches.
1 Pull the comb off the appliance.
2 Before you start to contour the hairline
around the ears, comb the hair ends over
the ears.
3 Press the on/off button to switch on the
appliance. (Fig. 6)
4 Tilt the appliance in such a way that only one
edge of the cutting element touches the hair
ends when you shape the contours around
the ears.
Only cut the hair ends. The hairline should be close
to the ear.
5 To contour the neckline and sideburns,
turn the appliance and make downward
strokes (Fig. 8).
Move the appliance slowly and smoothly. Follow
the natural hairline.
Cleaning
Clean the appliance every time you have used it
with the cleaning brush and with warm water
(max. 40°C).
Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids such
as petrol, acetone or ethereal oils to clean the
appliance.
Note: The appliance does not need any lubrication.
1 Switch off the appliance and disconnect
it from the mains.
2 Remove the comb from the appliance and
clean it with the cleaning brush.
3 Brush the outside of the cutting element.
4 Push the centre top end of the cutting
element upwards with your thumb until
it opens (Fig. 9).
5 Use the cleaning brush to remove the
cut hair (Fig. 10).
6 Clean the appliance under a warm running
tap. (Fig. 11)
Replacement
If the adapter is damaged, always have it replaced
with one of the original type in order to avoid
a hazard.
Only replace a damaged or worn comb with an
original Philips replacement comb.
Philips replacement parts (cutting element, combs,
handle and adapter) are available from your Philips
dealer and authorised Philips service centres.
If you have any difculties obtaining replacement
parts for the appliance, contact the Philips
Consumer Care Centre in your country. You nd
its phone number in the worldwide guarantee
leaet.
Environment
- Do not throw away the appliance with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve
the environment (Fig. 12).
- The built-in rechargeable batteries contain
substances that may pollute the environment.
Always remove the batteries before you
discard and hand in the appliance at an ofcial
collection point. Dispose of the batteries at
an ofcial collection point for batteries. If you
have trouble removing the batteries, you can
also take the appliance to a Philips service
centre. The staff of this centre will remove the
batteries for you and will dispose of them in an
environmentally safe way. (Fig. 13)
Removing the rechargeable batteries
Only remove the rechargeable batteries when
they are completely empty.
Be careful, the battery strips and housing parts
are very sharp.
1 Disconnect the appliance from the mains and
let the appliance run until the motor stops.
2 Check if there are any screws in the back or
front of the appliance. If so, remove them.
3 Remove the back and/or front panel of the
appliance with a screwdriver. If necessary, also
remove additional screws and/or parts until
you see the printed circuit board with the
rechargeable batteries.
4 If necessary, cut the wires to separate the
printed circuit board and the rechargeable
batteries from the appliance.
Guarantee and service
If you need service or information or if you have
a problem, please visit the Philips website at
www.philips.com/support or contact the
Philips Consumer Care Centre in your country.
You nd its phone number in the worldwide
guarantee leaet. If there is no Consumer Care
Centre in your country, go to your local Philips dealer.
Guarantee restrictions
Cutting units are not covered by the terms of the
international guarantee because they are subject
to wear.
简体中文
简介
感谢您的惠顾，欢迎光临飞利浦！
为了您能充分享受飞利浦提供的支持，请在
www.philips.com/welcome 上注册您的产品。
基本说明 (图 1)
1 修剪部件
2 开/关按钮
3 缩放轮
4 手柄
5 充电指示灯
6 产品插座接口
7 小号梳齿
8 大号梳齿
9 理发梳（仅限于 QC5390/80）
10 剪刀（仅限于 QC5390/80）
11 适配器
12 产品插头
13 收纳袋（仅限于 QC5390/80）
14 清洁刷
注意事项
使用本产品之前，请仔细阅读本使用说明书，
并妥善保管以备日后参考。
危险
- 确保电源适配器干燥。 (图 2)
警告
- 在将本产品连接电源前，务必检查当地的
电压是否与电源适配器所标电压一致。
- 电源适配器内含有一个变压器。切勿自行
更换插头，否则将导致严重后果。
- 肢体不健全、精神有障碍及缺乏相关经验
和知识的人（包括儿童）必须在监护人的
监督及指导下使用。
- 小孩不宜使用该产品。应照看好儿童，
确保他们不玩耍本产品。
- 使用前，请务必检查产品。如果产品损
坏，请勿再使用产品，否则可能对人体造
成伤害。
注意
- 为产品充电，须用随产品提供的电源适配
器。
- 必须在 5 摄氏度至 35 摄氏度之间的温度
下使用、存放和为本产品充电。
- 电源软线不能更换，如果软线损坏，此器
具（电源适配器）应废弃。如果电源软线
已损坏，则必须用原装型号进行更换，以
免发生危险。
- 如果产品的使用温度、气压或湿度方面改
变较大，应在使用之前让产品适应 30 分
钟。
更换
如果适配器已损坏，则务必更换原装型号适配
器，以免发生危险。
仅使用原装飞利浦替换修剪梳替换损坏或磨损
的修剪梳。
飞利浦替换部件（修剪部件、梳齿、手柄和适
配器）可从飞利浦经销商和经授权的飞利浦服
务中心获得。
如果您在购买本产品的替换部件时遇到任何困
难，请与您所在国家/地区的飞利浦客户服务
中心联系（可在全球保修卡中找到飞利浦客户
服务中心的电话号码）。
环保
- 弃置产品时，请不要将其与一般生活垃圾
堆放在一起；应将其交给官方指定的回收
中心。这样做有利于环保。 (图 12)
- 内置充电电池含有可能会污染环境的物
质。丢弃产品时，一定要将电池取出，
并将产品送到官方指定的回收站。到官方
指定的电池回收站处理电池。如果您在取
出电池时遇到问题，您也可以将产品送至
飞利浦维修中心。维修中心的员工会帮您
取出电池，并以环保的方式处理它。
(图 13)
卸下充电电池
只在充电电池的电量完全用尽时将其取出。
注意，电池带和外壳可能非常锋利。
1 断开产品电源并让产品继续运行，
直到马达停止。
2 检查产品的前面和后面是否有螺丝。
如果有，请将其卸下。
3 使用螺丝刀卸下产品的后面板和/或前面板。
如果必要，也卸下其他螺丝和/或部件，
直至您看到带有充电电池的印刷电路板。
4 如果必要，剪掉电线以分开印刷电路板，
然后从产品取出充电电池。
保修与服务
如果您需要服务或信息，或者有任何疑问，
请访问飞利浦网站：www.philips.com/
support。您也可与您所在国家/地区的飞利浦
客户服务中心联系（可从全球保修卡中找到其
电话号码）。如果您所在的国家/地区没有飞
利浦客户服务中心，请与当地的飞利浦经销
商联系。
保修条款
修剪部件不在国际保修条款的涵盖范围之内，
因为修剪部件属于易磨损物品。
提示
- 要获得最大修剪效率，请正对头发生长方
向移动本产品。
- 因为头发不会全部以相同的方向生长，
您需要以不同的方向移动产品
(向上、向下或交叉)。
- 确保梳齿的扁平部分完全接触到头皮，
以获得均匀的修剪效果。 (图 7)
- 在整个头部重复修剪动作，以确保您剪到
所有需要修剪的头发。
6 定期清除梳齿上的碎头发。
如果梳齿中积聚了大量头发，请将梳齿从本产
品中取出，然后将头发吹掉和/或甩掉。
不用梳齿的情况下修整轮廓
即使没有梳齿，您也可以使用本产品以非常贴
近头皮的距离（0.5 毫米）或紧密贴合颈部周
围和双耳附近的皮肤修剪头发。
由于修剪部件会去除接触到的每一根头发，
因此在没有梳齿修剪头发时要小心。
1 将梳齿从产品中拉出。
2 在开始修整耳朵周围的发际线轮廓之前，
请先沿发耳朵梳理发梢。
3 按开/关按钮启动产品。(图6)
4 修整耳朵周围的轮廓时，倾斜本产品，
仅使其修剪部件的一端接触到发根。
仅修剪发梢。发线应该紧贴双耳轮廓。
5 要紧贴颈部周围和鬓角轮廓，请转动产品
并向下修剪。(图8)
沿着发际线的自然生长线条缓慢、流畅地移
动产品。
清洁
每次使用产品后，请用清洁刷和温水
(最高 40°C) 来清洁本产品。
切勿使用压缩气体、钢丝绒、研磨性清洁剂或
腐蚀性液体（例如汽油、丙酮或香精油）来清
洁产品。
注意：产品不需要任何润滑。
1 关闭产品并断开电源。
2 将梳齿从产品上取下，然后用清洁刷进行
清洁。
3 用刷子清洁修剪部件的外侧。
4 用拇指将修剪部件正中间一端向上推，
直至其打开。(图9)
5 使用随附的清洁刷去除剪下的头发。
(图10)
6 在水龙头下用温水清洁产品。(图11)
- 一旦产品的任何部件损坏或损毁，请勿再
使用产品，否则可能对人体造成伤害。
符合标准
- 这款飞利浦产品符合关于电磁场 (EMF) 的
相关标准。据目前的科学证明，如果正确
使用并按照本用户手册中的说明进行操
作，本产品是安全的。
使用准备
注意：当电池电量耗尽时，您也可以直接插
电来使用本产品。
充电
首次使用前和长时间不用之后，请为产品至少
充电 1 小时。
当产品充满电时，它可在不接电源的情况下使
用长达 60 分钟。
如果充电指示灯呈橙色亮起，则表示电池电量
不足（还可以使用约 10 分钟），您需要为产
品充电。
1 确保产品电源已关闭。
2 将产品插头插入产品插座，并将电源适配
器插入插座。(图3)
, 充电指示灯开始呈绿色闪烁，表示产品正
在充电。
, 电池充满电时，充电指示灯将持续亮起绿
灯。30分钟后，充电指示灯熄灭以节省
能源。
使用本产品
使用梳齿修剪头发
本产品随机附送2种适合不同头发长度的梳齿
头发长度设定值将以毫米为单位显示在发梳
上。设定值对应于修剪后剩余头发的长度。
1 选择要使用的梳齿。
小号梳齿可修剪 3 毫米到 22 毫米之间的头发。
大号梳齿可修剪 23 毫米到 42 毫米之间的头发。
2 将梳齿直接滑入手柄两侧的导槽中
(可听到“咔哒”一声)。(图4)
3 要将修剪梳设置为所需设置，请将缩放轮
旋转至所需的长度设置。(图5)
, 产品前面的显示屏显示了选定的修剪后头
发长度（毫米）。
, 8秒钟后，显示屏关闭以节能。要再次激
活显示屏，请旋转缩放轮或按开/关按钮。
提示：记下您选择的剪发长度设定，
用作未来剪发过程中创造某种发型的参考。
4 按开/关按钮启动产品。(图6)
5 将本产品在头发上缓慢移动。
-
1
-
2
-
3
