DLV6230-17-19-22
LCD Monitors
Installation and Operations Manual
Model Number: DLV6230-17, -19, -22
Description: 17”, 19” and 22”
LCD Monitors
Dante LCD monitor manual
1
LCD montior
17 inch-22 inch
INSTRUCTION MANUAL
Dante LCD monitor adopts most advanced and industrial TFT-LCD panel,
with a strong and stable ability. Easily operate, low power consumption and no
radiation.
1. Features
For Surveillance monitoring
Long working life
One HDMI input，one VGA input，two composite BNC input，one BNC
composite output，one audio input
External 12V direct-current power，more conveninet for maintenance
Moving images are clearer and stable
Strong resistance to interference
Super image border processor
Easy to navigate menu
Universal remote control
Ultra-thin design, optional installation versions
Dante LCD monitor manual
2
2. Interface
（1）12VDC power input。
（2）HDMI video input。
（3） Analog RGB（PC） signal input, can connect personal PC
analog RGB(PC) signal.
（4）BNC composite video signal input 1：connect with composite
video signal。
（5）BNC composite video signal input 2：connect with composite
video signal。
（6）BNC composite video signal output，may connet external
monitor。
（7）Audio input。
3. Specification
Subject to change
（
（（
（1）
））
） （
（（
（4）
））
）
（
（（
（5）
））
）
（
（（
（2）
））
）
（
（（
（6）
））
）
（
（（
（3）
））
） （
（（
（7）
））
）
Dante LCD monitor manual
3
Romote controller introduction
Power
VGA
Move forward Move back
Up
Down
Mute
Enter
Source exchange
BNC
VGA BNC
Dante LCD monitor manual
5
1. Remote controller buttons function introduction
（1）“Power” If monitor is working, press power button to turn the monitor off
and go standby.
（2）“Mute” button：Press this button, sounds will disappear, press again, it
will be back.
（3）Move forward/back, used for adjust specification.
（4）“UP/down：press these each two button, specification will roll up/down.
（5）“Exit” can exit directly from menu。
（6）“Menu” Press this button, main menu will come out. Press again then
can exit main menu
（7）“Source”press and choose the signal options, with up/down to adjust.
2. Caution
（1）With seven mode AAA1，5V battery，keep the battery’s positive and
negative charges are same with the indication of the controller
（2）If remote controller doesent’s work for a long time, please take out the
batteries to avoid damaging the controller.
（3）Do not dismantle the controller
（4）Keep away from heat source
Dante LCD monitor manual
6
Menu adjustment introduction
1. Improving image effect
（1）Pressing “Menu”, then Up/Down to adjust image display.
（ 2 ） Pressing “Up/down” and enter corresponding options, then
progressively increase/down for adjustment.
（3）Press ”Menu” to quit
2. Image Setting
（1） Pressing “Menu”, then press UP/DOWN to enter display setting
options.
（2） Pressing Up/Down to enter the options, then press Up/down to
adjust corresponding options.
（3） Pressing “menu” to quit.
3. Menu Adjustment
（1） Pressing “Menu”, then press UP/DOWN to choose geometrical
adjustment menu.
（2） Pressing Up/Down to enter the options, then press Up/down to
adjust corresponding options.
（3） Pressing “menu” to quit.
4. Signal source options
Press “source”, submenu appears, adjust via UP/DOWN
Dante LCD monitor manual
7
Trouble Shooting Hints and repair
When there are problems with images and sounds, it is possible that the
connections are incorrect. Please make adjustments, based on the
information below. For additional information, please contact our after-sales
service department.
Troubles Reasons Repair
No images
Incorrect power
connection
No signal connection
Incorrect adjustment
1. check power plug
2. check if the power switch is on
3. check if the luminance, contrast and
audio are at the lowest level
No images Incorrect adjustment
Check if the luminance, contrast are at
the lowest level.
No color Incorrect adjustment Check If Chroma is the lowest level.
Dots from
interference
High frequency pulse
interference
Interference may be from electric tools
or other equipment such as
fluorescent light.
Keep away from the interfering source.
Power strip
interference
Radio frequecy
disturbance
If there are other items connected to
same strip may be cause
Remote controller
does not work
Lower power with
remote controller
1. check battery polarity
2. check if battery is still charged
-
1
-
2
-
3
-
4
-
5
-
6
-
7
