Dell POWEREDGE 840 クイックスタートガイド

www.dell.com | support.dell.com

Dell™ PowerEdge™ 840 Systems

Getting Started

With Your System

系统使用入门

はじめに

시스템시작하기

Model MVT01

CJ813fc0.fm Page 1 Wednesday, June 21, 2006 5:16 PM

www.dell.com | support.dell.com

Dell™ PowerEdge™ 840 Systems

Getting Started

With Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerEdge, and OpenManage are trademarks of Dell Inc.; Intel, Pentium, and Celeron

are registered trademarks and Core is a trademark of Intel Corporation; Microsoft, Windows, and Windows Server are registered trademarks

of Microsoft Corporation; Red Hat is a registered trademark of Red Hat, Inc.; SUSE is a registered trademark of Novell, Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model MVT01

May 2006 P/N CJ813 Rev. A00

Getting Started With Your System 3

System Features

This section describes the major hardware and software features of your system. It also provides

information about other documents you may need when setting up your system and how to obtain

technical assistance.

Major hardware and software features of your system include:

• One of the following processors:

– One Intel

®

Core™ 2 Duo

– One Intel Celeron

®

D, 300 sequence

– One Intel Pentium

®

4, 600 sequence

NOTE: Use the System Setup program to view processor information. See "Using the System Setup

Program" in your Hardware Owner’s Manual.

• A minimum of 512 MB of 533- or 667-MHz DDRII SDRAM memory, upgradable to a maximum

of 8 GB by installing combinations of 512-MB, 1-GB, or 2-GB unbuffered ECC memory modules

in four memory module sockets on the system board, single or dual rank.

• The following expansion slots:

– One PCIe x1 (3.3-V) slot

– One PCIe x8 (3.3-V) slot

– One 32-bit, 33-MHz PCI (5-V) slot

– Two 64-bit, 133-MHz PCI-X (3.3-V) slots

• An integrated Gigabit Ethernet NIC, capable of supporting 10-Mbps, 100-Mbps, or 1000-Mbps

data rates, with support for IPMI 1.5 and Wake-on-LAN.

• Four USB 2.0-compliant connectors (two on the front and two on the back) capable of supporting

a diskette drive, CD-ROM drive, keyboard, mouse, or USB flash drive.

• An integrated ATI ES1000 SVGA video controller supporting True-color graphics in the following

resolutions: 640 x 480, 800 x 600, 1024 x 768, 1280 x 1024, and 1600 x 1200.

• Systems management circuitry that monitors critical system voltages and fan speeds. The systems

management circuitry works in conjunction with the systems management software.

• Standard baseboard management controller with serial access.

• Back-panel connectors include PS/2 mouse and keyboard, serial, video, two USB connectors,

and one NIC connector.

4 Getting Started With Your System

• One 3.5-inch CD, DVD, or combination CD-RW/DVD in a peripheral drive bay.

NOTE: DVD devices are data only.

• Support for the following internal hard-drive configurations:

– Up to four internal, 1-inch, SATA hard drives with integrated drive controllers.

– Up to four internal, 1-inch, Serial-Attached SCSI (SAS) hard drives with an optional SAS

controller card or backplane.

NOTE: Hot-plug capability is supported only when SATA or SAS drives are connected to the optional SAS

controller card or backplane.

• Optional remote access controller (DRAC 4) for remote systems management. This option requires

a dedicated PCI slot.

• One 420-W power supply.

For more information about specific features, see "Technical Specifications."

The following software is included with your system:

• A System Setup program for quickly viewing and changing system configuration information. For more

information on this program, see "Using the System Setup Program" in the

Hardware Owner’s Manual

.

• Enhanced security features, including a system password and a setup password, available through

the System Setup program.

• System diagnostics for evaluating system components and devices. For information about using

the system diagnostics, see "Running the System Diagnostics" in your

Hardware Owner’s Manual

.

• Video drivers for displaying many popular application programs in high-resolution modes.

• SATA or SAS device drivers that allow the operating system to communicate with devices attached

to the integrated SATA or SAS subsystem. For more information about these drivers, see "Installing

Drives" in your

Hardware Owner’s Manual

.

• Systems management software and documentation CDs.

Supported Operating Systems

Your system supports the following operating systems:

• Microsoft Windows Server

™

2003, Standard Edition and Web Edition

• Microsoft Windows Server 2003, Standard Edition 64-Bit

•Red Hat

®

Enterprise Linux ES (version 3) for Intel x86

• Red Hat Enterprise Linux ES (version 4) for Intel x86

• Red Hat Enterprise Linux ES (version 4) for Intel Extended Memory 64 Technology (Intel EM64T)

•SUSE

®

Linux Enterprise Server 9 (Service Pack 2 or later) for Intel EM64T

• SUSE Linux Enterprise Server 10 for Intel EM64T

Getting Started With Your System 5

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and regulatory information. Warranty

information may be included within this document or as a separate document.

• The

Hardware Owner’s Manual

provides information about system features and describes how to

troubleshoot the system and install or replace system components. The

Hardware Owner’s Manual

is available on the CDs that came with your system or on

support.dell.com

.

• CDs included with your system provide documentation and tools for configuring and managing

your system.

• Systems management software documentation describes the features, requirements, installation,

and basic operation of the software.

• Operating system documentation describes how to install (if necessary), configure, and use

the operating system software.

• Documentation for any components you purchased separately provides information necessary

to configure and install these options.

• Updates are sometimes included with the system to describe changes to the system, software,

and/or documentation.

NOTE: Always check for updates on support.dell.com and read the updates first because they often

supersede information in other documents.

• Release notes or readme files may be included to provide last-minute updates to the system

or documentation or advanced technical reference material intended for experienced users or

technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not perform as expected,

see your Hardware Owner’s Manual.

Dell Enterprise Training and Certification is available; see www.dell.com/training for more information.

This service may not be offered in all locations.

6 Getting Started With Your System

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety instructions and important

regulatory information in your Product Information Guide.

This section describes the steps to set up your system for the first time.

CAUTION: Installing the feet on a stand-alone tower system is necessary to provide a stable foundation for the

system. Failure to install the feet poses the risk of having the system tip over, possibly causing bodily injury or

damage to the system.

CAUTION: Whenever you need to lift the system, get others to assist you. To avoid injury, do not attempt to lift the

system by yourself.

Unpacking the System

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

See the documentation included with your system on installing the system stabilizer feet.

Getting Started With Your System 7

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to plug into each

connector. Be sure to tighten the screws (if any) on the monitor's cable connector.

Connecting the Power

Connect the system’s power cable(s) to the system.

Plug the other end of the cable into a grounded electrical outlet or a separate power source

such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

8 Getting Started With Your System

Turning on the System

Turn on the system and monitor (optional).

Press the power button on the system and the monitor. The power indicators should light.

Adjust the monitor’s controls until the displayed image is satisfactory.

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system documentation that ships

with your system. To install an operating system for the first time, see the

Quick Installation Guide

.

Be sure the operating system is installed before installing hardware or software not purchased with the

system.

Getting Started With Your System 9

Technical Specifications

Processor

Processor type One Intel

®

Core

™

2 Duo processor

or

One Intel Celeron

®

D, 300 sequence

or

One Intel Pentium

®

4, 600 sequence

Expansion Buses

Bus type PCIe, PCI-X, PCI

Expansion slots

PCIe

One 3.3-V, x1

One 3.3-V, x8

PCI-X Two full-height, full-length, 3.3-V,

64-bit, 133-MHz

PCI One 5-V, 32-bit, 33-MHz

Memory

Architecture 72-bit ECC unbuffered DDR2 533/667 MHz

SDRAM DIMMs, single- or dual-channel

Memory module sockets Four 240-pin

Memory module capacities 512 MB, 1 GB, or 2 GB

Minimum RAM 512 MB (one 512-MB module)

Maximum RAM 8 GB

Drives

Hard Drives

SATA Up to four internal, 1-inch-high (3.5-inch form

factor) drives connected to integrated drive

controller or RAID controller card (non-hot plug)

or SAS backplane (hot plug)

SAS Up to four internal, 1-inch-high (3.5-inch form

factor) drives connected to optional SAS backplane

(hot-plug) or SAS controller card (non-hot plug)

NOTE: Mixing of SATA and SAS drives is not

supported

10 Getting Started With Your System

Optical drive One IDE CD, DVD, or combination

CD-RW/DVD

NOTE: DVD devices are data only.

Diskette drive One optional 3.5-inch, 1.44-MB

Tape drive One optional IDE in optical drive bay

Connectors

Externally accessible

Back

NIC One RJ-45 (for integrated 1-Gigabit NIC)

PS/2-style keyboard 6-pin mini-DIN

PS/2-compatible mouse 6-pin mini-DIN

Serial 9-pin, DTE, 16550-compatible

USB Two 4-pin, USB 2.0-compliant

Video 15-pin VGA

Front

Video 15-pin VGA

USB Two 4-pin, USB 2.0-compliant

Internally accessible

IDE channel 40-pin

SATA channels Two 7-pin

Video

Video type

Integrated ATI ES1000 SVGA controller

Video memory

16 MB

Power

AC power supply

Wattage

420 W

Voltage

100–240 VAC, 50/60 Hz

Heat dissipation

2275 BTU/hr maximum

Drives (continued)

Getting Started With Your System 11

Maximum inrush current Under typical line conditions and over the entire

system ambient operating range, the inrush current

may reach 55 A for 10 ms or less or 25 A at 150 ms

or less.

System battery

CR 2032 3.0-V lithium ion coin cell

Physical

Height 43.9 cm (17.3 in)

Width

19.8 cm (7.8 in)

Depth

50.0 cm (19.7 in)

Weight 19.1 kg (42 lb)

Environmental

NOTE: For additional information about environmental measurements for specific system configurations,

see www.dell.com/environmental_datasheets.

Temperature

Operating 10° to 35°C (50° to 95°F)

Storage –40° to 65°C (–40° to 149°F)

Relative humidity

Operating 20% to 80% (noncondensing)

Storage 5% to 95% (noncondensing)

Maximum vibration

Operating 0.26 G (half-sine wave) at a sweep of 3 to 200 MHz

for 15 minutes

Storage 0.5 G at 3–200 Hz for 15 min

Maximum shock

Operating Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse on

each side of the system) of 36 G for up to 2.6 ms

Storage Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse on

each side of the system) of 71 G for up to 2 ms

Altitude

Operating –16 to 3048 m (–50 to 10,000 ft)

Storage –16 to 10,668 m (–50 to 35,000 ft)

Power (continued)

12 Getting Started With Your System

www.dell.com | support.dell.com

Dell™ PowerEdge™ 840 系统

系统使用入门

注、注意和警告

注：注表示可以帮助您更好地使用计算机的重要信息。

注意：

注意表示可能会损坏硬件或导致数据丢失，并告诉您如何避免此类问题。

警告：

警告表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式进行复制。

本文中使用的商标：

Dell

、

DELL

徽标、

PowerEdge

和

OpenManage

是

Dell Inc.

的商标；

Intel

、

Pentium

和

Celeron

是

Intel

Corporation

的注册商标，

Core

是

Intel Corporation

的商标；

Microsoft

、

Windows

和

Windows Server

是

Microsoft Corporation

的注册商标；

Red Hat

是

Red Hat, Inc.

的注册商标；

SUSE

是

Novell, Inc.

的注册商标。

本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。

Dell Inc.

对本公司的商标和产品名称之外

的其它商标和产品名称不拥有任何专有权。

型号

MVT01

2006

年

5

月

P/N CJ813

修订版

A00

系统使用入门 15

系统配置

本节介绍系统的主要硬件和软件配置。还介绍了有关在安装系统时可能需要的其它说明文件的

信息，以及如何获得技术帮助的信息。

系统的主要硬件和软件配置包括：

•

以下处理器之一：

–

一个

Intel

®

Core™ 2 Duo

–

一个

Intel Celeron

®

D

，

300

序列

–

一个

Intel Pentium

®

4

，

600

序列

注：

使用系统设置程序可以查看处理器信息。请参阅《硬件用户手册》中的 “使用系统设置

程序”。

•

至少

512 MB

的

533 MHz

或

667 MHz DDRII SDRAM

内存，通过在系统板上的四个内存模块

插槽中安装

512 MB

、

1 GB

或

2 GB

非缓冲

ECC

内存模块组合，最多可升级至

8GB

，单排或

者双排。

•

以下扩充槽：

-

一个

PCIe x1 (3.3-V)

插槽

-

一个

PCIe x8 (3.3-V)

插槽

-

一个

32

位、

33 MHz PCI (5 V)

插槽

-

两个

64

位、

133 MHz PCI-X (3.3 V)

插槽

•

一个集成的吉位以太网

NIC

，可支持

10 Mbps

、

100 Mbps

或

1000 Mbps

数据速率，

支持

IPMI 1.5

和通过

LAN

唤醒的功能。

•

四个

USB 2.0

兼容连接器（两个在正面，两个在背面），可支持软盘驱动器、

CD-ROM

驱动器、键盘、鼠标或

USB

快擦写驱动器。

•

一个集成的

ATI ES1000 SVGA

视频控制器，在以下分辨率中下可支持真彩色图形：

640 x 480

、

800 x 600

、

1024 x 768

、

1280 x 1024

和

1600 x 1200

。

•

系统管理电路，用于监测系统临界电压和风扇速率。系统管理电路需要与系统管理软件配合

工作。

•

标准底板管理控制器，支持串行访问。

•

背面板连接器，包括

PS/2

鼠标连接器、键盘连接器、串行连接器、视频连接器、

两个

USB

连接器和一个

NIC

连接器。

•

一个

3.5

英寸

CD

、

DVD

或组合

CD-RW/DVD

（位于外围设备驱动器托架中）。

注：

DVD 设备仅用于数据。

16 系统使用入门

•

支持以下内部硬盘驱动器配置：

-

通过集成的驱动器控制器，最多可支持四个内部

1

英寸

SATA

硬盘驱动器。

-

通过可选的

SAS

控制器卡或背板，最多可支持四个内部

1

英寸串行连接

SCSI (SAS)

硬盘驱动器。

注：

仅当 SATA 或 SAS 驱动器连接至可选的 SAS 控制器卡或背板时，才支持热插拔功能。

•

可选的远程访问控制器

(DRAC 4)

，用于远程系统管理。此选件需要一个专用

PCI

插槽。

•

一个

420 W

电源设备。

有关具体配置的详情，请参阅 “技术规格”。

您的系统附带以下软件：

•

系统设置程序，用于快速查看和更改系统配置信息。有关此程序的详情，请参阅

《硬件用户手册》中的 “使用系统设置程序”。

•

增强的安全保护功能，包括系统密码和设置密码，可通过系统设置程序进行设置。

•

系统诊断程序，用于评估系统组件和设备。有关使用系统诊断程序的信息，请参阅

《硬件用户手册》中的 “运行系统诊断程序”。

•

视频驱动程序，用于以高分辨率模式显示多种常见应用程序。

•

SATA

或

SAS

设备驱动程序，允许操作系统与连接至集成

SATA

或

SAS

子系统的设备进行通信。

有关这些驱动程序的详情，请参阅《硬件用户手册》中的 “安装驱动器。”

•

系统管理软件和说明文件

CD

。

支持的操作系统

您的系统支持以下操作系统：

•

Microsoft Windows Server

™

2003

，标准版和

Web

版

•

Microsoft Windows Server 2003

标准版（

64

位）

•

适用于

Intel x86

的

Red Hat

®

Enterprise Linux ES

（第

3

版）

•

适用于

Intel x86

的

Red Hat Enterprise Linux ES

（第

4

版）

•

用于

Intel 64

位扩展内存技术

(Intel EM64T)

的

Red Hat Enterprise Linux ES

（第

4

版）

•

适用于

Intel EM64T

的

SUSE

®

Linux Enterprise Server 9

（

Service Pack 2

或更高版本）

•

适用于

Intel EM64T

的

SUSE Linux Enterprise Server 10

系统使用入门 17

您可能需要的其它信息

警告：

《产品信息指南》，提供了重要的安全信息和管制信息。保修信息可能包括在该说明文件中，

也可能作为单独的说明文件提供。

•

《硬件用户手册》提供了有关系统部件的信息，并介绍了如何排除系统故障以及如何安装或更换

系统组件。《硬件用户手册》可在随系统提供的

CD

或在

support.dell.com

上获得。

•

随系统附带的

CD

提供了用于配置和管理系统的说明文件和工具。

•

系统管理软件说明文件，介绍了软件的功能、要求、安装和基本操作。

•

操作系统说明文件，介绍了如何安装（如果有必要）、配置和使用操作系统软件。

•

单独购买的任何组件所附带的说明文件，提供了有关配置和安装这些选件的必需信息。

•

系统有时附带更新，用于说明对系统、软件和

/

或说明文件所做的更改。

注：

请始终检查 support.dell.com 上的更新信息并首先进行阅读，因为该网站上的信息常常会取代其

它说明文件中的信息。

•

系统可能附带版本注释或自述文件，以提供系统或说明文件的最新更新内容，或者为有经验的用

户或技术人员提供高级技术参考资料。

获得技术帮助

如果您对本指南中的步骤有疑问，或系统运行无法达到预期效果，请参阅《硬件用户手册》。

Dell

可以提供企业培训与认证；有关详情，请访问

www.dell.com/training

。并非在所有国家和地区

均可提供此服务。

安装和配置

警告：

在执行以下过程之前，请阅读并遵循《产品信息指南》中的安全说明和重要的管制信息。

本节介绍初次安装系统时的步骤。

警告：

要为系统提供稳固的基础，需要在独立的塔式系统上安装支脚。如果未安装支脚，可能存在导致

系统倾翻的危险，从而可能造成人身伤害或损坏系统。

警告：

无论何时您需要抬起系统，均需找他人协助。为了避免造成伤害，请勿尝试自行抬起系统。

18 系统使用入门

打开系统包装

打开系统包装并识别每项物品。

妥善保管好所有运输包装材料，以备将来使用。

参阅随系统提供的说明文件安装系统稳定支脚。

连接键盘、鼠标和显示器

连接键盘、鼠标和显示器（可选）。

系统背面的连接器附有图标，这些图标指示了要插入每个连接器的电缆。

确保拧紧显示器的电缆连接器上的螺钉（如果有）。

ページを読み込んでいます...

Dell POWEREDGE 840 クイックスタートガイド

関連論文