7
ENGLISH
Thank you for choosing Electrolux Pure C9 vacuum cleaner. Always use
original accessories and spare parts to get the best results. This product is
designed with the environment in mind. All plastic parts are marked for
recycling purposes.
BEFORE STARTING
• Read this manual carefully.
• Check that all parts described are included.
• Pay special attention to the safety precautions!
DESCRIPTION OF PURE C9 VACUUM CLEANER
A. Display
A1 rotary knob control*
A2 remote control*
B. Filters lid
C. Fine dust lter
D. Pre-motor lter
E. Parking slots
F. Power cord
G. Carry handle
H. Cyclone compartment and
nose cone lter
I. Air channel
J. Dust compartment
L. AeroPro hose
M. AeroPro handle
M1 AeroPro Classic handle*
M2 AeroPro Ergo handle*
M3 AeroPro Remote Control
handle*
N. AeroPro telescopic tube
O. Parking clip
Nozzle Accessories
K. AeroPro 3in1 tool
T. Motorized nozzle*
U. FlowMotion nozzle*
V. FlowMotion LED nozzle
(with front lights)*
W. AeroPro Turbo nozzle*
X. AeroPro Mini Turbo nozzle*
Y. ParkettoPro nozzle*
Z. AeroPro FlexProPlus nozzle*
AA. AeroPro Long crevice
nozzle*
AB. BedPro nozzle*
* Selected models only
Picture page 2-6
HOW TO USE THE VACUUM CLEANER
1 Check that all lters are properly placed before using the vacuum
cleaner.
2 Insert the hose into the cleaner (to remove it, press the lock buttons
and pull). Insert the hose into the hose handle until the lock button
clicks (to release it, press the lock button and pull).
3 Attach the telescopic tube to the nozzle. Attach the telescopic tube to
the hose handle (to remove it, press the lock button and pull).
4 Adjust the telescopic tube by holding the lock with one hand and
pulling the handle with the other hand.
3IN1 ACCESSORY TOOL
5 You can fasten the clip-on holder and 3in1 tool under the handle to
have it easily accessible. The tool has 3functions, see pictures on next
page.
CHANGING THE BATTERIES*
6 Nozzle with front lights*: Before rst use, remove the protective lm
(on top of the batteries). Change batteries when front lights start
blinking fast. Use 2 AA batteries.
7 Handle with remote control*: Change battery when light indicator
turns red or is not responding when pressing any button. Use only
batteries type LITHIUM CR1632.
NB: Remove the batteries from the product before scrapping. Follow
your country’s rules for collection of batteries and electrical products.
START/STOP THE VACUUM CLEANER AND ADJUST SUCTION
POWER
8 Pull out the power cord and plug it into the mains. Press the ON/OFF
button to turn the cleaner on/o. Models with remote control can also
be operated by the ON/OFF button on the handle.*
9 After cleaning, push the REWIND button to rewind the cable.
10 Adjust suction power (manual control models): Turn the rotary knob
on the cleaner or use the air valve on the handle.*
Adjust suction power (remote control models): Press +/- button on
the handle. MIN/MAX and symbols indicators on display will show
level of power.*
VACUUMING WITH THE UNIVERSAL NOZZLE V*, W*
11 Change nozzle setting with the pedal. Icon illustrates recommended
oor type (hard oor or carpet).
FlowMotion LED nozzle*: Move the nozzle forward. The front light
turns on automatically after a few seconds. When the nozzle is not
used, the light turns o automatically after a few seconds.
PARKING POSITIONS, MOVING THE VACUUM CLEANER
12 Use parking position (1), at the back of the vacuum cleaner, when you
pause while vacuuming.
Use parking position (2), underneath the vacuum cleaner, to carry and
store the vacuum cleaner.
13 The vacuum cleaner has two carrying handles.
EMPTYING THE DUST COMPARTMENT
14 Empty the dust compartment when the level of dust has reached the
maximum limit ("MAX"-mark).
Press the release button and pull to remove the dust compartment.
Hold the dust compartment over a dust bin. Press the unlock button
underneath the lid, open the lid by swinging it outwards. Empty dust
into the dustbin. Ret in reverse order.
REPLACING THE FILTERS
15 Pull the FILTER button to open the lter lid.
Clean the ne dust lter after six months of use, or when dust is visible.
Pull the tab on the frame to remove the ne dust lter. Rinse the lter
under running water.
NB: Do not use cleaning agents. Let the lter dry completely (min. 24 h
in room temperature) before putting back !
16 Press and slide the lock mechanism to the right to release the
pre-motor lter. Remove the lter by pulling the lter frame tab.
Clean the pre-motor lter after twelve months of use.
Only use original s-lter Recommended by Electrolux (See
Consumables and Accessories). Rinse the inside (dirty side) in
lukewarm tap water. Tap the lter frame to remove the water. Repeat
the process four times.
NB: Do not use cleaning agents. Avoid touching the lter surface.
Let the lter dry completely (min. 24 h in room temperature) before
putting back ! Change the washable lter at least once a year or when
it is very dirty or damaged.
After replacing the lters, close the lter lid until it is clicked back into
place.
17 Cleaning the nose cone lter: the nose cone lter is located inside the
cyclone compartment. Clean the nose cone lter if dust has entered.
Pull the nose cone lter to remove. Remove dust with your hand.
Clean under running water if heavily soiled. Ret in reverse order.
NB: Do not use cleaning agents. Let the lter dry completely (min. 24 h
in room temperature) before putting back!
CLEANING THE UNIVERSAL NOZZLE V*, W** AND THE TURBO
NOZZLE X*
18 Disconnect the universal nozzle from the tube. Clean with the hose
handle.
Disconnect the turbo nozzle from the tube and remove entangled
threads etc by snipping them away with scissors. Use the hose handle
to clean the nozzle. *
Enjoy a great cleaning experience with Pure C9!
Electrolux reserves the right to change products, information and
specications without notice.