DeWalt DCF403N ユーザーマニュアル

ブランド: DeWalt

モデル: DCF403N

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

このマニュアルも適しています

DCF414N

DCF403

DCF414

English (original instructions) 3

简体中文 12

Fig. A

图A

Fig. B

XXXX XX XX

图B

Fig.C Fig.D

Fig.E Fig.F

Fig.G Fig.H

图C

图G图H

图F

图D

ENGLISH

Congratulations!

You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the most

reliable partners for professional power toolusers.

Technical Data

DCF403 DCF414

Voltage VDC 18 (20 Max) 18 (20 Max)

Battery type Li‑Ion Li‑Ion

Weight (without battery pack) kg 1.65 1.65

Batteries Chargers / Charge Times (Minutes)***

Cat# VDC Ah Weight(kg) DCB104 DCB107 DCB112

DCB1102

DCB115

DCB1104

DCB117

DCB1112 DCB118 DCB132

DCB546/DCB606 18/54 (20/60 Max) 6.0/2.0 1.08 60 270 170 90 40 60 90

DCB547/DCB609/DCB609G 18/54 (20/60 Max) 9.0/3.0 1.46 75* 420 270 135* 60 75* 135*

DCB548/DCB612 18/54 (20/60 Max) 12.0/4.0 1.46 120 540 350 180 80 120 180

DCB549/DCB615 18/54 (20/60 Max) 15.0/5.0 2.12 125 730 450 230 90 125 230

DCB180 18 (20 Max) 3.0 0.62 45 140 90 45 45 45 45

DCB181 18 (20 Max) 1.5 0.35 22 70 45 22 22 22 22

DCB182/DCB204 18 (20 Max) 4.0 0.61 60/40** 185 120 60 60/40** 60/40** 60

DCB183/DCB203 18 (20 Max) 2.0 0.40 30 90 60 30 30 30 30

DCB184/DCB184G/DCB205 18 (20 Max) 5.0 0.62 75/50** 240 150 75 75/50** 75/50** 75

DCB187 18 (20 Max) 3.0 0.54 45 140 90 45 45 45 45

DCB189/DCB240 18 (20 Max) 4.0 0.54 60 185 120 60 60 60 60

DCB186 18 (20 Max) 6.0 0.95 60 270 170 90 60 60 90

DCB208 18 (20 Max) 8.0 0.95 70 360 240 120 70 70 120

DCBP034 18 (20 Max) 1.7 0.32 27 82 50 27 27 27 27

DCBP520 18 (20 Max) 5.0 0.75 75/50** 240 150 75 75/50** 75/50** 75

*Date code 201811475B or later

**Date code 201536 or later

***Battery charge times matrix provided for guidance only; charge times will vary depending on temperature and condition ofbatteries.

English (original instructions)

RIVET TOOLS

DCF403, DCF414

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Denotes risk of electricshock.

Denotes risk offire.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTUREREFERENCE

ENGLISH

The term “power tool” in the warnings refers to your

mains‑operated (corded) power tool or battery‑operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non‑skid safety shoes, hard hat or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be

caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust‑relatedhazards.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe

injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

ENGLISH

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

e ) Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

ofinjury.

f ) Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or temperature

above 130°C may causeexplosion.

g ) Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified range

may damage the battery and increase the risk offire.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorised serviceproviders.

Riveter Safety Warnings

WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• Do not work without a collection container. Mandrels are

ejected to the rear by the riveter and can causeinjuries.

• Do not point the riveter at persons or yourself during

operation and do not work without material to be

riveted. The blind rivet can be ejected from the riveter and

causeinjuries.

• After the riveting process is completed tilt the unit

backwards, so that the residual mandrels fall into the

collectioncontainer.

• Ventilation slots for the engine must not be covered;

do not insert any objects into them. Damage or personal

injury couldresult.

• When not in use, place tool on its side on a stable surface

where it will not cause a tripping or falling hazard. Some

tools with large battery packs will stand upright on the battery

pack but may be easily knockedover.

• Disconnect the power tool from the power supply/

battery if it cannot be switched off. Do not use the power

tool if it cannot be switched on and off with the switch.

Any power tool that cannot be controlled with the switch is

dangerous and must berepaired.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

SAVE THESE INSTRUCTIONS

Chargers

DeWALT chargers require no adjustment and are designed to be

as easy as possible tooperate.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

iYour DeWALT charger is double insulated in

accordance with IEC60335; therefore, no earth wire

isrequired.

If the supply cord is damaged, it must be replaced only by

DeWALT or an authorised serviceorganisation.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for the

power input of your charger (refer to Technical Data). The

minimum conductor size is 1mm2; the maximum length is30m.

When using a cable reel, always unwind the cablecompletely.

Important Safety Instructions for All

BatteryChargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (referto TechnicalData).

Before using charger, read all

instructions and cautionary markings on charger, battery pack, and

product using batterypack.

WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.

WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.

CAUTION: Burn hazard. To reduce the risk of injury,

charge only DeWALT rechargeable batteries. Other types of

batteries may burst, causing personal injury anddamage.

ENGLISH

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The Stage 1Charging blink indicator represents the charge

process that charges the majority of the battery's capacity.

Stage2Charging blink indicator represents the remainder, or

top off charge process, for the battery to reach fullcapacity.

4. The completion of charge for Stage 1or Stage 2will be

indicated by the Stage's light remaining ON continuously.

The battery pack is fully charged when both Stage 1and

Stage 2Charging lights remain ON continuously, and it may

be removed and used at this time or left in thecharger.

NOTE: To remove the battery pack, some chargers require the

battery pack release button to bepressed.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Indicators

Stage 1Charging

Stage 2Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing tolight.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the pack

charging mode. This feature ensures maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed to

cool the battery pack. The fan will turn on automatically when the

battery pack needs to be cooled. Never operate the charger if the

fan does not operate properly or if ventilation slots are blocked.

Do not permit foreign objects to enter the interior of thecharger.

CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting toclean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging DeWALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire, electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised service

centre when service or repair is required. Incorrect reassembly

may result in a risk of electric shock, electrocution orfire.

• In case of damaged power supply cord, the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard 220-

240V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig.B)

NOTE: To ensure maximum performance and life of lithium‑ion

battery packs, charge the battery pack fully before firstuse.

ENGLISH

Electronic Protection System

XR Li‑Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium‑ion battery

pack in the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non‑metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All

BatteryPacks

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture, causing serious

personalinjury.

• Charge the battery packs only in DeWALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in locations

where the temperature may fall below 4˚C (39.2˚F)

(such as outside sheds or metal buildings in winter), or

reach or exceed 40˚C (104˚F) (such as outside sheds or

metal buildings insummer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium‑ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persist, seek

medicalattention.

WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.

WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.

WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.

CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation

WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come into contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well‑insulated from

materials that could contact them and cause a short

circuit. NOTE: Lithium‑ion batteries should not be put in

checkedbaggage.

DeWALT batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards, which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations; International Maritime Dangerous Goods

(IMDG) Regulations; and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road

(ADR). Lithium‑ion cells and batteries have been tested to

section 38.3of the UN Recommendations on the Transport of

Dangerous Goods Manual of Tests andCriteria.

In most instances, shipping a

DeWALT

battery pack will

be excepted from being classified as a fully regulated

Class9Hazardous Material. In general, only shipments containing

a lithium‑ion battery with an energy rating greater than 100Watt

Hours (Wh) will require being shipped as fully regulated Class9.

ENGLISH

All lithium‑ion batteries have the Wh rating marked on the pack.

Furthermore, due to regulation complexities,

DeWALT

does

not recommend air shipping lithium‑ion battery packs alone

regardless of Wh rating. Shipments of tools with batteries (combo

kits) can be air shipped as excepted if the Wh rating of the battery

pack is no greater than 100Wh.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Storage Recommendations

1. The best storage place is one that is cool and dry away from

direct sunlight and excessive heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely depleted

of charge. The battery pack will need to be recharged beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the

labels on the charger and the battery pack may show the

followingpictographs:

LRead instruction manual beforeuse.

p Refer to Technical Data for chargingtime.

q Do not probe with conductiveobjects.

r Do not charge damaged batterypacks.

s Do not expose towater.

t Have defective cords replacedimmediately.

u Charge only between 4˚C and 40˚C.

v Only for indooruse.

x Discard the battery pack with due care for

theenvironment.

y Charge DeWALT battery packs only with designated

DeWALT chargers. Charging battery packs other than

the designated DeWALT batteries with a DeWALT

charger may make them burst or lead to other

dangeroussituations.

z Do not incinerate the batterypack.

Battery Type

The following tools operate on an 18‑volt (20V Max) battery

pack: DCF403, DCF414

Refer to Technical Data for morebatteries information.

Package Contents

The package contains:

1 Riveter

4 Nosepieces (DCF403)

3 Nosepieces (DCF414)

1 Set of spare jaws

Li‑Ion battery pack

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not included

with N models. Battery packs and chargers are not included with

NT models. Bmodels include Bluetooth® batterypacks.

NOTE: The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth®, SIG, Inc. and any use of

such marks by DeWALT is under license. Other trademarks and

trade names are those of their respectiveowners.

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

a Read instruction manual beforeuse.

g Wear earprotection.

f Wear eyeprotection.

n Visible radiation. Do not stare intolight.

Date Code Position (Fig.B)

The production date code 14 consists of a 4‑digit year followed

by a 2‑digit week and is extended by a 2‑digit factorycode.

Description (Fig.A)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1 Nosepieces

2 Screw cap

3 Nose housing

ENGLISH

4 Nose housing nut

5 Mandrel collector

6 Spare nosepiece holder

7 Exhaust vent

8 Main handle

9 Trigger switch

10 LED worklight

11 Battery pack

12 Battery release button

13 Spare jaws

Intended Use

These rivet tools are designed for installation blindfasteners.

DO NOT insert any objects other than the rivets specified in the

instruction manual into thenosepiece.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

These rivet tools are professional powertools.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

WARNING: Use only DeWALT batteries andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig.B)

NOTE: Make sure your battery pack 11 is fullycharged.

To Install the Battery Pack into the Tool Handle

1. Align the battery pack with the rails inside the tool’s

handle(Fig. B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the battery release button 12 and firmly pull the

battery pack out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig.B)

Some DeWALT battery packs include a fuel gauge, which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button15. A combination of the three green LED lights will

illuminate, designating the level of charge left. When the level

of charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end‑userapplication.

Mounting the Nosepiece (Fig.C)

1. Select the correct nosepiece for the rivet to be installed.

Refer to the number or letter16 on the nosepiece and

the Rivet Size Chart to select the proper nosepiece for

theapplication.

2. Unscrew and remove the screw cap2.

3. Place the nosepiece1 into the nose housing3.

4. Screw the screw cap onto the nosehousing.

Rivet Size Chart

Rivet Diameter

Nosepiece mm Inches

DCF403

12.4 3/32

23.2 1/8

34.0 5/32

44.8 3/16

DCF414

A4.8 3/16

B6.0 15/64

C6.4 1/4

Mandrel Collector and Spare Nosepiece

Holder (Fig.D)

WARNING: Do not use the tool without the mandrel

collectorattached.

The mandrel collector5 and spare nosepiece holder6 attach

to the rear of the tool.

The tool can be used without the spare nosepieceholder.

To remove the mandrel collector or spare nosepiece holder,

unscrew them until they are removed. If you are using the tool

with the spare nosepiece holder, attach it to the tool first, and

then attach the mandrelcollector.

ENGLISH

Belt Hook (Fig.E)

Included with Some Models

WARNING: To reduce the risk of serious personal

injury, ONLY use the tool's belt hook to hang the

tool from a work belt. DO NOT use the belt hook for

tethering or securing the tool to a person or object during

use. DO NOT suspend tool overhead or suspend objects

from the belthook.

WARNING: To reduce the risk of serious personal

injury, ensure the screw holding the belt hook issecure.

IMPORTANT: When attaching or replacing a belt hook, use only

the screw that is provided. Be sure to securely tighten thescrew.

A belt hook21 can be attached to either side of the tool

using only the screw22 provided, to accommodate left‑ or

right‑handed users. If the belt hook is not desired at all, it can be

removed from thetool.

To move the belt hook, remove the screw22 that holds it in

place then reassemble on the opposite side. Be sure to securely

tighten thescrew.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

Proper Hand Position (Fig.G)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a suddenreaction.

Proper hand position requires one hand on the main handle8.

LED Worklight (Fig.A)

CAUTION: Do not stare into the LED. Serious eye injury

couldresult.

The LED worklight10 improves visibility in the direct workarea.

When the tool is activated by pressing the trigger switch9,

the LED worklight10 will automatically turn on. The LED

worklight will turn off 60seconds after the on/off button has

beenreleased.

The LED worklight10 will flash slowly when the battery state

of charge is low.

The LED worklight10 will flash fast if the nose equipment is

clogged. Refer to Cleaning the Nose Equipment or Replacing

Jaws for the proper cleaningprocedure.

Installing a Blind Rivet (Fig.A, F)

To Install a Blind Rivet

1. Place the blind rivet20 in the nosepiece1.

2. Position the tool as shown in Proper HandPosition.

3. Pull and hold the trigger switch9 until the rivet is fully set

in theapplication.

4. When the blind rivet has been set completely, release

the trigger switch. The tool will return to its initial

positionautomatically.

5. Tilt the unit backwards and the mandrel will go to the

mandrel collector5 by gravity. The mandrel will also be

pushed into the mandrel collector by pulling the nextrivet.

If you release the switch before the end of the setting stroke,

the tool will immediately return to its initial position. If the blind

rivet has not been set completely, repeat the previoussteps.

Emptying the Mandrel Collector (Fig.D)

Always empty the mandrel collector5 for broken‑off

rivet mandrels before it is completely full in order to

preventblockages.

1. Unscrew the mandrel collector by turning itanticlockwise.

2. Empty the mandrel collector into a suitable recycling or

wastebin.

3. Screw the mandrel collector back onto the power tool by

turning itclockwise.

MAINTENANCE

Your power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regularcleaning.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

The charger and battery pack are notserviceable.

Maintenance Frequency

Item Frequency

General tool inspection Daily

Clean and lubricate nose equipment 5000 rivets

*Recommend contacting authorised service centre

Cleaning

WARNING: Electrical shock and mechanical hazard.

Disconnect the electrical appliance from the power source

beforecleaning.

WARNING: To ensure safe and efficient operation,

always keep the electrical appliance and the ventilation

slotsclean.

WARNING: Never use solvents or other harsh chemicals

for cleaning the non‑metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

ENGLISH

Ventilation slots can be cleaned using a dry, soft non‑metallic

brush and/or a suitable vacuum cleaner. Do not use water or

any cleaning solutions. Wear approved eye protection and an

approved dustmask.

Cleaning the Nose Equipment or Replacing

Jaws (Fig.A, H)

1. Loosen the nose housing nut4. Remove the nose

housing3 and nose housingnut.

2. Clean the inside of the nose housing using a drycloth.

3. Pull back the locking sleeve17 as indicated by the arrow.

4. Untighten the pulling hull18.

5. Clean the jaws19 and the jaw pusher using a dry cloth. If

necessary, replace the jaws with spare jaws13.

NOTE: When replacing the jaws, use only DeWALT

brandjaws.

6. Apply grease to the outside of the clamping jaw

assembly19.

7. Put the jaw assembly19 into the pulling hull18 and

mount it onto the tool. Tighten the pulling hull by hand and

ensure it is secured by the locking sleeve17.

NOTE: A molybdenum disulfide‑based grease

isrecommended.

8. Mount the nose housing and nose housing nut and tighten

by hand.

Cleaning the Tool Exterior (Fig.A)

Keep the brushless motor exhaust vent7 openings free from

dust and dirt. If necessary, use a soft, moist cloth to remove dust

and dirt from the exhaust vents. Blow dirt and dust out of the

main power tool housing with dry air as often as dirt is seen

collecting in and around the exhaustvents.

Optional Accessories

WARNING: Since accessories, other than those offered

by DeWALT, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only DeWALT‑recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can be

recovered or recycled, reducing the demand for raw materials.

Please recycle electrical products and batteries according to local

provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long‑life battery pack must be recharged when it fails to produce

sufficient power on jobs that were easily done before. At the end of

its technical life, discard it with due care for ourenvironment:

• Run the battery pack down completely, then remove it from

thetool.

• Li‑Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

After Service and Repair

DeWALT

service centers are staffed with trained personnel to provide

customers with efficient and reliable product service.We do not take

any responsibility when you have repaired in unauthorized service

center. You can refer to the leaflet of CONTACT CENTER LOCATOR in

product package and contact us through hotline, website or social

media to find the nearest

DeWALT

service center around you.

简体中文

ENGLISH

恭喜！

您选择了本款

DeWALT

工具。凭借多年的产品开发和创新经验，

DeWALT

已经成为专业电动工具用户最可靠的合作伙

伴之一。

技术数据

DCF403 DCF414

电压 VDC 18 (最大20) 18 (最大20)

电池类型 Li‑Ion Li‑Ion

重量（不含电池包） kg 1.65 1.65

电池充电器/充电时间（分钟）***

型号 VDC Ah 重量（ kg）DCB112

DCB1102

DCB115

DCB1104 DCB118

DCB606 18/54 (最大20/60) 6.0/2.0 1.05 170 90 60

DCB609/DCB609G 18/54 (最大20/60) 9.0/3.0 1.46 270 135* 75*

DCB612 18/54 (最大20/60) 12.0/4.0 1.44 350 180 120

DCB615 18/54 (最大20/60) 15.0/5.0 2.12 450 230 125

DCB182 18 (最大20) 4.0 0.61 120 60 60/40*

DCB203 18 (最大20) 2.0 0.40 60 30 30

DCB184/DCB184G 18 (最大20) 5.0 0.62 150 75 75/50**

DCB208 18 (最大20) 8.0 0.95 240 120 70

DCBP034 18 (最大20) 1.7 0.32 50 27 27

DCBP520 18 (最大20) 5.0 0.75 150 75 75/50**

*日期码 201811475B 或以后

**日期码 201536 或以后

***电池包充电时间表仅供参考；实际充电时间将根据电池包的温度和状况而变化。

English (original instructions)

锂电无刷铆钉枪

DCF403, DCF414

警告：为降低伤害风险，请阅读使用手册。

定义：安全指南

下列定义描述了各标志术语的严重程度。请仔细阅读本

手册，并注意这些标志。



危险：表示存在紧急危险情况，如果不加以避免，

将导致死亡或严重伤害。



警告：潜在的危险情况，如果不加以避免，可能导

致死亡或重伤。



小心：表示存在潜在危险情况，如果不加以避免，

可能导致轻度或中度伤害。

注意：与人身伤害无关的行为，如果不加以避免，

可能导致财产损失。



表示存在触电风险。

表示存在火灾风险。

电动工具通用安全警告



警告：请阅读本电动工具随附的所有安全警告、

说明、图示和规定。未能遵照以下所列说明会导

致电击、火灾和/或严重伤害。

保存所有警告和使用手册以备查阅。

警告中的术语“电动工具”指市电驱动（有线）电动工具

或电池驱动（无线）电动工具。

1) 工作区安全

a )

保持工作场地清洁和明亮。杂乱和黑暗的场地会

引发事故。

b )

不要在易爆环境，如有易燃液体、气体或粉尘的

环境下操作电动工具。电动工具产生的火花会点

燃粉尘或气体。

c )

操作电动工具时，远离儿童和旁观者。注意力不

集中会使你失去对工具的控制。

2) 电气安全

a )

电动工具插头必须与插座相配。绝不能以任何方

式改装插头。需接地的电动工具不能使用任何转

换插头。未经改装的插头和相配的插座将降低电

击风险。

简体中文

ENGLISH

b )

避免人体接触接地表面，如管道、散热片和冰箱。

如果你身体接触接地表面会增加电击风险。

c )

不得将电动工具暴露在雨中或潮湿环境中。水进

入电动工具将增加电击风险。

d )

不得滥用电源线。绝不能用电源线搬运、拉动电

动工具或拔出其插头。使电源线远离热源、油、锐

边或运动部件。受损或缠绕的电源线会增加电击

风险。

e )

当在户外使用电动工具时，使用适合户外使用的

延长线。适合户外使用的电线将降低电击风险。

f )

如果无法避免在潮湿环境中操作电动工具，应使

用带有剩余电流装置（RCD）保护的电源。RCD的

使用可降低电击风险。

3) 人身安全

a )

保持警觉，当操作电动工具时关注所从事的操作

并保持清醒。当你感到疲倦，或在有药物、酒精或

治疗反应时，不要操作电动工具。在操作电动工

具时瞬间的疏忽会导致严重人身伤害。

b )

使用个人防护设备。始终佩戴护目镜。防护装置，

诸如适当条件下使用防尘面具、防滑安全鞋、安

全帽、听力防护等装置能减少人身伤害。

c )

防止意外起动。在连接电源和/或电池包、拿起或

搬运工具前，应确保开关处于关断位置。手指放

在开关上搬运工具或开关处于接通时通电会导

致危险。

d )

在电动工具接通之前，拿掉所有调节钥匙或扳

手。遗留在电动工具旋转零件上的扳手或钥匙

会导致人身伤害。

e )

请勿过分伸展。时刻注意立足点和身体平衡。这

样能在意外情况下能更好地控制住电动工具。

f )

适当着装。不要穿宽松衣服或佩戴饰品。让你的

头发和衣服远离运动部件。宽松衣服、佩饰或长

发可能会卷入运动部件。

g )

如果提供了与排屑、集尘设备连接用的装置，要

确保其连接完好且使用得当。使用集尘装置可降

低尘屑引起的危险。

h )

不要因为频繁使用工具而产生的熟悉感而掉以

轻心，忽视工具的安全准则。某个粗心的动作可

能在瞬间导致严重的伤害。

4) 电动工具使用和注意事项

a )

切勿强制使用电动工具。根据用途使用合适的电

动工具。选用合适的按照额定值设计的电动工具

会使你工作更有效、更安全。

b )

如果开关不能接通或关断电源，则不能使用该电

动工具。不能通过开关来控制的电动工具是危险

的且必须进行修理。

c )

在进行任何调节、更换附件或贮存电动工具之

前，必须从电源上拔掉插头和／或卸下电池包（

如可拆卸）。这种防护性的安全措施降低了电动

工具意外起动的风险。

d )

将闲置不用的电动工具贮存在儿童所及范围之

外，并且不允许不熟悉电动工具和不了解这些说

明的人操作电动工具。电动工具在未经培训的使

用者手中是危险的。

e )

维护电动工具及其附件。检查运动部件是否调整

到位或卡住，检查零件破损情况和影响电动工具

运行的其他状况。如有损坏，应在使用前修理好

电动工具。许多事故是由维护不良的电动工具

引发的。

f )

保持切削刀具锋利和清洁。维护良好地有锋利切

削刃的刀具不易卡住而且容易控制。

g )

按照使用说明书，并考虑作业条件和要进行的作

业来选择电动工具、附件和工具的刀头等。将电

动工具用于那些与其用途不符的操作可能会导

致危险情况。

h )

保持手柄和握持表面干燥、清洁，不得沾有油脂。

在意外的情况下，湿滑的手柄不能保证握持的安

全和对工具的控制。

5) 电池式工具使用和注意事项

a )

仅使用生产者规定的充电器充电。将适用于某种

电池包的充电器用到其他电池包时可能会发生

着火危险。

b )

仅使用配有专用电池包的电动工具。使用其他电

池包可能会产生伤害和着火危险。

c )

当电池包不用时，将它远离其他金属物体，例如

回形针、硬币、钥匙、钉子、螺钉或其他小金属物

体，以防电池包一端与另一端连接。电池包端部

短路会引起燃烧或着火。

d )

在滥用条件下，液体可能会从电池包中溅出，应

避免接触。如果意外碰到液体，用水冲洗。如果液

体碰到了眼睛，还应寻求医疗帮助。从电池中溅

出的液体可能会发生腐蚀或燃烧。

e )

不要使用损坏或改装过的电池包或工具。损坏或

改装过的电池包可能呈现无法预测的结果，导致

着火、爆炸或伤害。

f )

不要将电池包暴露于火或高温中。电池包暴露于

火或高于130°C的高温中可能导致爆炸。

g )

请遵循所有充电说明，请勿在说明中规定的温度

范围以外的环境对电池包或工具充电。不当或在

指定范围以外的温度下充电，可能导致电池损坏

并增加火灾风险。

6) 维修

a )

让专业维修人员使用相同的备件维修电动工具。

这将保证所维修的电动工具的安全。

b )

切勿维修损坏的电池包。电池包仅能由生产者或

其授权的维修服务商进行维修。

铆钉枪安全警告



警告：不得改装本电动工具或其任何部件，否则

可能会导致损坏或人身伤害。



警告：始终佩戴安全眼镜。普通眼镜不是安全眼

镜。始终佩戴经认证的安全防护设备。

•

请勿在无收集容器的情况下工作。心轴会被铆钉枪

弹出到后面，可能会致人受伤。

•

在操作过程中，不要将铆钉对准自己或他人，不要

在没有被铆接材料的情况下工作。盲铆钉可能会从

铆钉枪上弹出，致人受伤。

•

铆接过程结束后，将设备向后倾斜，使残留的心轴

落入收集容器中。

•

发动机的通风槽不能被覆盖，不要将任何物体插入

其中。否则可能会导致损坏或人身伤害。

简体中文

ENGLISH

•

不使用时，应将工具侧放在稳定的表面上，以免造

成绊倒或坠落的危险。一些带有大型电池组的工具

可以直立在电池组上，但可能很容易被撞倒。

•

如果电动工具无法关闭，请将其与电源/电池断开。

如果电动工具无法用开关打开和关闭，请勿使用。

不能通过开关来控制的电动工具是危险的且必须

进行修理。

剩余风险

尽管遵守了相关的安全法规并采用了安全装备，某些剩

余风险仍然是无法避免的。这些风险包括：

•

听力损伤。

•

飞溅颗粒造成的人身伤害风险。

•

使用时附件发热导致的灼伤风险。

•

长时间使用引起的人身伤害风险。

请妥善保管好这些说明

充电器

DeWALT

充电器无需做出任何调整，专为简易操作而设

计。

电气安全

电机只适用一种工作电压。请务必检查电池组的电压是

否和铭牌上的电压一致。请务必检查电池组的电压是否

和铭牌上的电压一致。

DeWALT

充电器符合IEC60335双重绝缘要求，因

此无需使用接地线。

如果电源线损坏，必须仅由

DeWALT

或授权的维修机构

负责更换。

使用延长线

除非绝对必要，否则请勿使用延长线。使用适合您的充

电器输入功率的合格延长线（请参阅

技术数据

）。最小的

导线尺寸为1平方毫米；最大长度为30米。使用电缆卷筒

时，请务必拉出所有的电缆。

针对所有电池充电器的重要安全说明

请妥善保管好这些说明: 本手册包含重要的兼容电池充

电器安全和操作说明（请参阅

技术数据

）。在使用充电器

之前，请先阅读所有指示以及充电器、电池组和使用电

池组的产品上的警告标记。



警告：电击危险。请勿让任何液体进入充电器，否

则可能会导致触电。



警告：我们建议使用漏电保护额定电流为30毫安

或以下的漏电保护装置。



小心：烧伤危险。为降低人身伤害风险，请仅使用

DeWALT

充电式电池充电。使用其它类型的电池可

能会引起爆裂，并导致人身伤害和损害。



小心：应看管好儿童，以确保他们不将此设备当

做玩具来玩。

注意：在某些情况下，当充电器的插头插入电源

插座时，充电器内部裸露的充电接触点可能因

为外来物件而短路。请勿让能导电的异物靠近

充电器腔，这些外来物件包括但不限于钢棉、铝

箔或任何金属颗粒的堆积物。充电器内没有电池

组时，请断开充电器与电源的连接。清洗前，务必

拔掉充电器。

•

请勿试图使用本手册指定的充电器以外的其他任何

充电器为电池包充电。充电器和电池包都是专门设

计的，互相配合使用。

•

这些充电器不适合用于为

DEWALT

充电式电池充电

以外的任何其他用途。否则，可能会导致火灾、触电

或电击。

•

请勿将充电器暴露于雨中或雪中。

•

断开充电器连接时，应捏住插头将其拔下，而非通

过拉拽电源线拔下插头。这将降低对电插头和电线

的损害风险。

•

确保电源线布置在不易踩踏、踢绊、拉扯或会受到

损害或压力的位置。

•

除非绝对必要，否则请勿使用延长线。使用不正确

的延长线可能导致火灾、触电或电击的风险。

•

请勿将任何物件放在充电器上面，或是把充电器放

在可能会堵住通风槽的柔软表面，导致充电器的内

部过热。请把充电器放置在远离任何热源的地方。

充电器通过外壳顶端和底端的槽进行通风。

•

请勿使用电源线或插头已损坏的充电器，请立即更

换这些充电器。

•

如果充电器受到强烈重击、掉落或出现其他损坏情

况，请勿使用充电器。请将损坏的充电器送到授权

服务中心。

•

请勿自行拆卸充电器。请将需要检修或修理的充电

器送到授权服务中心。重装不正确可能导致触电、

电击或火灾风险。

•

必须立即将已损坏的电源线交由制造商、服务代理

或类似的合格人员进行更换以防止安全隐患。

•

清洁前，请先断开充电器和插座的连接，以降低触

电风险。取出电池组不会降低此风险。

· 不得将两个充电器连接在一起。

•

充电器是为220- 240V的标准家用电源而设计。请勿

试图在任何其他电压下使用充电器。此规则不适用

于车载充电器。

为电池充电（图B）

注意：为了确保锂离子电池的效能和使用寿命最大化，

在首次使用电池包之前必须将其完全充电。

1. 插入电池组前，先将充电器的插头插到相应的电源

插座上。

2. 将电池组插入充电器，确保电池组在充电器中完全

就位。红色（充电中）指示灯将不断闪烁，表示充电过

程已经开始。

3. 第1阶段充电闪烁指示器表示为大部分电池容量充

电的充电过程。第2阶段充电闪烁指示器表示电池达

到满容量的剩余电量或充电过程。

4. 第1阶段或第2阶段的充电完成后，对应阶段的指示

灯将常亮。第1阶段和第2阶段的充电指示灯常亮时，

表示电池组已充满电，此时可取出电池组使用，或将

其留在充电器中。

注意：在拆卸电池组时，部分充电器需要按住电池组释

放按钮

简体中文

ENGLISH

电池组

针对所有电池组的重要安全说明

在订购更换电池组时，请务必附上目录型号和电压。

包装箱内的电池组并未完全充电。使用电池组和充电器

之前，请阅读下列安全说明，然后遵循所述的充电程序。

请阅读所有说明

· 请勿在易爆环境，如有易燃液体、气体或粉尘的环

境中充电或使用电池。在充电器中插入或取出电池

时可能会点燃粉尘或气体。

· 不得强行将电池放进充电器。请勿以任何方式改装

电池包并将电池包插入不兼容的充电器，这种操作

可能会导致电池包破裂，造成严重的人身伤害。

· 只使用

DEWALT

充电器为电池包充电。

· 请勿喷溅电池包或将其浸泡在水或其他液体中。

· 请勿在温度可能降至 4°C (39.2°F) 的地方（如冬

天户外的棚子或金属建筑物中）或达到或超过

40°C(104°F) 的地方（如夏天户外的棚子或金属建筑

物中）存储或使用工具和电池包。

· 即使电池组严重受损或完全损坏，也请勿焚化电池

组。电池组在火中会发生爆炸。锂离子电池包在燃

烧时会释放有毒气体和物质。

· 如果电池液体接触到皮肤，请立即以中性肥皂和清

水冲洗接触的地方。如果电池液体不慎进入眼睛，

应睁开眼睛并用清水冲洗至少 15 分钟或直到刺激

感消失。如果需要医疗救助，请告知医护人员。电池

电解质由液状有机碳酸盐和锂盐的混合物组成。

· 已打开电池的内部物质可能导致呼吸道刺激。请保

持空气流通。如果症状持续存在，请就医。



警告：烧伤危险。电池液如果接触到火花或火焰

可能会燃烧。



警告：不得以任何理由试图打开电池组。电池组

外壳破裂或损坏时，请勿将电池组插入充电器。

请勿挤压、掉落或损坏电池组。请勿使用受过强

烈重击、掉落、碾压或以任何其它方式（如被钉

子穿破、受到锤子的重击、踩踏）受损的电池组

或充电器。否则可能会引起触电或电击。损坏的

电池组应送回服务中心进行回收。



警告：火灾危险。请勿在存储或搬运电池组时让

金属物品接触暴露的电池两极。例如，请勿将电

池组放在围裙、口袋、工具盒、产品套件盒、抽屉

等可能与散钉、螺丝、钥匙等物品接触的地方。



小心：不使用时，应将工具侧放在稳定的表面上，

以免造成绊倒或坠落的危险。一些带有大型电池

组的工具可以直立在电池组上，但可能很容易被

撞倒。

运输 

警告：火灾危险。电池运输途中，如果电池两极意

外接触导电材料，可能会引发火灾。运输电池时，

务必保护电池两极，确保与可能接触电池导致短

路的材料良好绝缘。注意：不应将锂离子电池放

入托运行李中。

DeWALT

电池符合所有适用的行业和法律标准规定的

运输规范，包括《联合国危险品运输建议规章范本》(UN

充电器操作

关于电池组的充电状态，请参阅以下指示灯说明。

指标器

第1阶段充电

第2阶段充电

已完全充电

热/冷电池组

延迟*

*红色指示灯会继续闪烁，但黄色指示灯在本次操作过

程中会亮起。电池包达到适当温度后，黄色指示灯会熄

灭，充电器将恢复充电程序。

兼容充电器不会对故障电池包充电充电器指示灯不亮

时表示电池有故障。

注意：这可能也表示充电器有问题。

如果充电器提示存在故障，请将充电器和电池组送到授

权的服务中心进行测试。

热/冷电池组延迟

当充电器检测到电池组过热或过冷时，它会自动启动

热/冷电池延迟模式，暂停充电，直到电池组达到适当的

温度。然后，充电器会自动切换到电池组充电模式。此功

能可确保电池组拥有最长的使用寿命。

冷电池组充电速度比热电池组充电速度慢。电池组在整

个充电周期的充电速度都会较慢，即使电池组升温也不

会恢复到最大速度。

DCB118充电器配备了内部风扇，用于冷却电池组。当电池

组需要冷却时，该风扇会自动启动。如果风扇无法正常工

作或通风槽被堵塞，切勿操作充电器。请勿让异物进入充

电器的内部。

电子保护系统

XR锂离子电池工具采用了电子保护系统设计，可让电池

包免受过载、过热或过度放电之害。

如果电子保护系统处于运作状态，该工具将自动停止操

作。如果发生这种情况，请将锂离子电池包放在充电器

上，直至其完全充电。

壁挂式安装

这些充电器设计为可以安装在墙上，也可以直立在桌面

或工作台面上。如果安装在墙上，请确保充电器的位置

可以连接到电源插座，并且远离墙角或其他可能妨碍空

气流通的障碍物。将充电器背面作为在墙上安装螺丝的

位置模板。使用至少 25.4 毫米长、螺丝帽直径至少 7‑9 毫

米的石膏板螺丝（单独购买）牢牢固定充电器，将螺丝最

大限度钉入木材，预留约 5.5 毫米露在墙外。将充电器背

面的安装槽对准露出的螺丝，完全放置到位。

充电器清洁说明



警告：电击危险。清洁前，请将充电器从交流电源

插座上拔下。可用布或非金属软刷清除充电器外

部的污垢和油脂。请勿使用水或任何清洁剂。不

得让任何液体渗入工具，不得让工具的任何部件

浸在液体中

简体中文

ENGLISH

Recommendations on the Transport of Dangerous Goods)

、《

国际

航空运输协会 (IATA) 危险品规则》 (International Air Transport

Association (IATA) Dangerous Goods Regulations) 、《国际海运

危险品 (IMDG) 规则》(International Maritime Dangerous Goods

(IMDG) Regulations) 和《欧洲危险货物国际公路运输协定》

(European Agreement Concerning TheInternational Carriage of

Dangerous Goods by Road) (ADR)。离子电池和电池包已遵循

《联合国危险品运输建议规章范本手册》第 38.3 节关于

测试和标准的说明通过测试。

大多数情况下，发运

DeWALT

电池包不属于完全管制的9类

危险品。通常情况下，只有当运输包含一个能量等级大于

100 瓦时 (Wh) 的锂离子电池时，才需要作为完全管制的

9 类危险品发运。所有的锂离子电池都在电池组上标明

了额定电量。此外，由于法规比较复杂，无论瓦时等级是

多少，

DeWALT

都不建议单独空运锂离子电池包。发运包含

电池的工作（组合套件）时，如果电池包的能量等级不大

于 100 瓦时 (Wh)，则可以按计划空运。

无论发运是否纳入完全管制范围内，运输公司均有责

任遵循最新法规中关于包装、标签/标记和单据的要求。

本手册本节的信息是出于善意提供，且认为在编制文档

时准确无误。不提供明示或暗示的担保。购买方负有确

保其行为遵守适用法规的责任。

存放建议

1. 最好将电池存放在阴凉、干燥、远离阳光直射、不会

过热或过冷的地方。为了获得最佳的电池性能和使

用寿命，请您在不使用电池组时将其存储在室温下。

2. 长期存储时，建议将完全充电的电池组从充电器取

出，存储在阴凉、干燥的地方，以达到最佳效果。

注意：电池组不应在电池已完全耗尽的状态下存放。使

用电池组之前，必须重新为电池组充电。

充电器和电池组上的标签

除了在本手册中所使用的标志，充电器和电池组的标签

还包括：

L使用前请阅读使用手册。

p 充电时间请参考

技术数据。

q 请勿使用导电物体戳刺。

r 请勿对损坏的电池组充电。

s 请勿将其暴露于水中。

t 应立即更换有缺陷的电线。

u 请只在4℃和40℃之间的温度下充电。

v 只能在室内使用。

x 弃置电池组时，请妥善处理以保护我们的环境。

y 只能用指定的

DeWALT

充电器给

DeWALT

电池包充

电。使用

DeWALT

充电器为非

DeWALT

电池充电可

能会导致电池爆炸或出现其他危险情况。

z 请勿焚化电池组。

电池类型

以下工具使用18伏（ 20V Max）的电池包：DCF403、DCF414

更多信息，请参考

技术数据。

包装内的物品

包装中包含：

1 铆钉枪

4 快换头（DCF403）

3 快换头（DCF414）

1 一套备用钳口

锂离子电池组

1 使用手册

注意：电池包、充电器和工具箱没有随 N 型号附送。电池

包和充电器没有随 NT 型号附送。B 型号包括BLUETOOTH®

电池包。

注意：BLUETOOTH®标志和徽标是BLUETOOTH®, SIG, INC.的

注册商标，DEWALT对这些标识的任何使用均经过许可。

其他商标和商标名均归各自所有者所有。

检查工具、部件或附件是否在运输过程中损坏。

操作前，请抽空仔细阅读并掌握本手册。

工具上的标记

工具上印有下列图形：

a 使用前请阅读使用手册。

g 请佩戴听力保护器。

f 请佩戴护目装备。

n 可见辐射。请勿盯着光看。

日期代码位置（图B）

生产日期代码14由4位数的年和2位数的周组成，后跟2

位数的工厂代码。

描述（图 A）



警告：不得改装本电动工具或其任何部件，否则

可能会导致损坏或人身伤害。

1 快换头

2 螺丝帽

3 鼻罩

4 鼻罩螺母

5 芯棒收集盒

6 多型号快换头架

简体中文

ENGLISH

7 排气口

8 主手柄

9 触发开关

10 LED工作灯

11 电池组

12 电池释放按钮

13 备用钳口

设计用途

这些铆钉工具可用于安装单面紧固件。

除了说明书中提及的铆钉外，请勿将任何其他物体插入

快换头中。

请勿在潮湿环境中，或在存在易燃液体或气体的环境中

使用本工具。

这些铆钉工具是专业的电动工具。

请勿让儿童接触本工具。缺乏经验的操作员需要在监督

下使用本工具。

· 儿童和体弱者。在没有他人监督的情况下，儿童或体

弱者不适宜使用本产品。

· 本产品不适合体力、感官或智力不足以及缺乏经验、

知识或技能的人员（包括儿童）使用，除非一旁有能

为他们的安全负责的监督人员。不得在无人监管的

情况下让儿童接触本产品。

组装与调整



警告：为降低严重的人身伤害风险，在进行任何

调整或取出/安装附件或配件之前，请关闭工具

并断开电池包连接。意外启动可能会导致人身

伤害。



警告：仅使用

DEWALT

电池和充电器。

从工具中插入和取出电池组（图B）

注意：确保您的电池包11已经充满电。

要将电池包安装到工具手柄中

1. 将电池包对准工具手柄内的轨道（图B）。

2. 将电池包滑入手柄内，使其牢牢地固定在工具内，并

确保您听到其锁定到位的声音。

从工具中取出电池包

1. 按下电池释放按钮12，将电池包从工具握柄中稳妥

地拉出。

2. 按本手册充电器部分所述将电池包插入充电器中。

电量计电池组（图B）

一些

DeWALT

电池包带有一个包含三个绿色LED指示灯的

电量计，用于指示电池包内的剩余电量。

按下电量计按钮 15 不松开，即可启动电量计。三个绿

色LED指示灯将以组合方式亮起，以指示剩余电量。当电

池内的电量低于可用限制时，电量计将不会亮起，电池

将需要重新充电。

注意：电量计仅指示电池组的剩余电量。它并不表示该

工具的功能，且将根据产品组件、温度和最终使用者的

使用情况而有所不同。

安装快换头（图

）

1. 为待安装的铆钉选择正确的快换头。参照铆钉上的

数字或字母16和

铆钉尺寸表

，选择适用的铆钉。

2. 拧开并取下螺丝帽字母2。

3. 将快换头1放入鼻罩字母3中。

4. 将螺丝帽拧到鼻罩上。

铆钉尺寸表

铆钉直径

快换头 mm 英寸

DCF403

12.4 3/32

23.2 1/8

34.0 5/32

44.8 3/16

DCF414

A4.8 3/16

B6.0 15/64

C6.4 1/4

芯棒收集盒和多型号快换头架（图

D） 

警告：未安装芯棒收集盒时，请不要使用该工具。

芯棒收集盒5和多型号快换头架6安装在工具的后面。

该工具可以在没有多型号快换头架的情况下使用。

如需卸下芯棒收集盒或多型号快换头架，请拧开它们，

直至卸下。如果使用工具时，需使用多型号快换头架，请

先将其安装到工具上，然后再安装芯棒收集盒。

皮带钩（图E）

包括某些型号



警告：为减少严重人身伤害的风险，仅可用皮带

钩将工具挂在工作带上。使用过程中，切勿用皮

带钩将工具拴在或固定在人或物体上。切勿将工

具悬挂在头顶或将物体悬挂在皮带钩上。



警告：为了减少人身伤害的风险，请确保固定皮

带钩的螺钉紧固。

重要事项：在固定或更换皮带钩时，仅可使用随附的螺

钉。一定要牢固地拧紧螺钉。

为了适应惯用左手的用户，用提供的螺钉22将皮带钩21

固定在工具的任何一侧。如果完全不需要皮带钩，可将

其从工具上取下。

若要移动皮带钩，请拆下固定其的螺钉22，然后在另一

侧重新安装。一定要牢固地拧紧螺钉。

简体中文

ENGLISH

操作

使用说明



警告：务必遵守安全指示和适用法规。



警告：为降低严重的人身伤害风险，在进行任何

调整或取出/安装附件或配件之前，请关闭工具

并断开电池包连接。意外启动可能会导致人身

伤害。

正确的手部位置（图G）



警告：为了减低严重人身伤害的风险，请务必如

图示那样正确放置双手。



警告：为了减低造成严重人身伤害的风险，预期

有突然反作用力时务必握紧。

手部正确的位置是一只手放在主手柄上。8

LED工作灯（图A）



小心：请不要直视LED灯。直视可能会导致视力严

重受损。

LED工作灯10可提高直接工作区域的能见度。

按下触发开关9启动工具时，LED工作灯10会自动亮起。

松开开/关按钮60秒后，LED工作灯将熄灭。

电池电量不足时，LED工作灯10会缓慢闪烁。

如果快换头设备堵塞，LED工作灯 10 会快速闪烁。有关

正确的清洁程序，请参考

清洁鼻部设备或更换钳口

。

安装盲铆钉（图A、F）

安装盲铆钉的方法

1. 将盲铆钉20放入快换头1。

2. 如

正确的手部位置

所示，定位工具。

3. 拉动并按住扳机开关 9，直到铆钉被完全固定在应

用中。

4. 待盲铆钉被完全固定后，松开扳机开关。工具会自动

返回到初始位置。

5. 将设备向后倾斜，心轴将在重力作用下进入芯棒收

集盒5 。拉动下一个铆钉，心轴也将被推入芯棒收集

盒。

如果在设定行程结束前松开开关，工具将立即返回到

初始位置。如果盲铆钉没有被完全设置好，请重复前面

的步骤。

清空芯棒收集盒（图D）

在芯棒收集盒 5 完全装满之前，一定要清空芯棒收集

盒，以防止堵塞。

1. 逆时针旋转芯棒收集盒，将其拧下。

2. 将芯棒收集盒内的物品倒入一个合适的回收箱或垃

圾箱。

3. 顺时针旋转芯棒收集盒，将其拧回电动工具上。

维护

您的电动工具设计精良，可以长期使用，仅需极少维护。

若要持续令人满意的工作效果，则需对工具进行适当的

保养和定期清洁。



警告：为降低严重的人身伤害风险，在进行任何

调整或取出/安装附件或配件之前，请关闭工具

并断开电池包连接。意外启动可能会导致人身

伤害。

充电器和电池组无法维修。

维护频率

项目频率

一般工具检查每天

清洁和润滑鼻部设备每5,000个

铆钉

*建议联系授权维修中心

清洁



警告：电击和机械危险。清洁前，请将电器与电源

断开。



警告：为确保操作安全、有效，请注意清洁电器和

通风槽。



警告：不得使用溶剂或其它刺激性化学制品来清

洁工具的非金属部件。这些化学物质可能会削弱

这些部位使用的材料。请用布蘸温和的肥皂水擦

拭。不得让任何液体渗入工具，不得让工具的任

何部件浸在液体中

通风槽可以用干燥、柔软的非金属刷和/或合适的吸尘

器进行清洁。请勿使用水或任何清洁剂。请戴上合格的

护目镜和防尘面具。

清洁鼻部设备或更换钳口（图A、H）

1. 松开鼻罩螺母4。卸下鼻罩3和鼻罩螺母。

2. 用干布清洁鼻罩内部。

3. 如箭头所示，拉回锁紧套17。

4. 松开拉壳18。

5. 用一块干布清洁钳口19和钳口推杆。如有必要，用

备用钳口13更换钳口。注意：更换钳口时，只使用

DeWALT

品牌的钳口。

6. 在钳口组件19的外部涂上油脂。

7. 将钳口组件19放入拉壳18，并将其安装在工具上。

用手拧紧拉壳，并确保其被锁紧套17所固定。

注意：建议使用二硫化钼基润滑脂。

8. 安装鼻罩和鼻罩螺母，用手拧紧。

清洁工具外部（图A）

确保无刷电机的排气口 7 没有灰尘和污垢。如有必要，

用一块柔软的湿布清除排气口的灰尘和污垢。一旦看到

通风口及其周围积聚了尘屑，请用干燥的空气将灰尘和

尘屑从主电动工具外壳内吹出。

可选配件



警告：由于除

DeWALT

提供的配件外，其他配件没

有经过本产品的测试，因此将这些配件与本工具

一起使用可能会有危险。为了减少受伤的风险，

本产品仅可使用

DeWALT

推荐的配件。

请向您的经销商咨询更多关于合适附件的信息。

ページが読み込まれています...

DeWalt DCF403N ユーザーマニュアル

ブランド: DeWalt

モデル: DCF403N

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

このマニュアルも適しています

DCF414N

PDFをダウンロードします

報告

他の言語で

English: DeWalt DCF403N User manual