Dell PowerConnect M6348 クイックスタートガイド

www.dell.com | support.dell.com

Dell™ PowerConnect™

M6348 Stackable Switches

Getting Started Guide

使用入门指南

入門指南

Guide de mise en route

Handbuch zum Einstieg

Panduan Pengaktifan

はじめに

시작 안내서

Guía de introducción

Model PCM6348

הדובע תליחת ךירדמ

www.dell.com | support.dell.com

Dell™ PowerConnect™

M6348 Stackable Switch

Getting Started Guide

Model PCM6348

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerConnect are trademarks of Dell Inc.; Microsoft and Windows are registered

trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model PCM6348

November 2009 P/N H851N Rev. A01

3

Contents

Installation

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking the Switch

. . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Package Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking Steps

. . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connecting a Switch to a Terminal

. . . . . . . . . . . . . . . . . . . . . 6

Assembling a Stack

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Starting and Configuring the Switch

Connecting the Terminal to the Switch . . . . . . . . . . . . . . . . . . . 8

Booting the Switch

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Initial Configuration

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Initial Configuration Procedure

. . . . . . . . . . . . . . . . . . . . . 10

Example Session

. . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Managing a Stack

Master and Member Switches . . . . . . . . . . . . . . . . . . . . . . . 13

Stack Startup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Topology Discovery

. . . . . . . . . . . . . . . . . . . . . . . . . . 13

Auto Stack ID Assignment

. . . . . . . . . . . . . . . . . . . . . . . 14

Firmware Version Checking

. . . . . . . . . . . . . . . . . . . . . . 14

System Initialization

. . . . . . . . . . . . . . . . . . . . . . . . . . 14

CLI/ Telnet/ Web Interface

. . . . . . . . . . . . . . . . . . . . . . . . . 15

Insertion and Removal of Switches

. . . . . . . . . . . . . . . . . . . 15

Operating as Standalone Switch

. . . . . . . . . . . . . . . . . . . . 15

Stack ID Renumbering

. . . . . . . . . . . . . . . . . . . . . . . . . 15

User Controls

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4

Advanced Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Retrieving an IP Address From a DHCP Server

. . . . . . . . . . . . . 16

Security Management and Password Configuration

. . . . . . . . . . . 17

Managing the Switch

Using a Web Browser to Manage the Switch . . . . . . . . . . . . . . . . 20

Starting the Application

. . . . . . . . . . . . . . . . . . . . . . . . 20

Understanding the Interface

. . . . . . . . . . . . . . . . . . . . . . 20

Getting Started Guide 5

Installation

This document provides basic information to install, configure, and operate

Dell™ PowerConnect™ M6348 systems. For more information, see the

Hardware Owner’s Manual

,

which is available on your

User Documentation

CD, or check the Dell Support web site at

support.dell.com

for the latest updates on documentation and firmware.

Site Preparation

Before installing the switch, make sure that the chosen installation location meets the site

requirements specified in the

Hardware Owner’s Manual

.

Unpacking the Switch

Package Contents

When unpacking each switch, make sure that the following items are included:

• One PowerConnect switch

• One USB type A-to-DB9 serial cable

•

User Documentation

CD

• Getting Started Guide

• Product Information Guide

Unpacking Steps

NOTE: Before unpacking the switch, inspect the container and immediately report any evidence of

damage.

1

Place the container on a clean, flat surface and cut all straps securing the container.

2

Open the container or remove the container top.

3

Carefully remove the switch from the container and place it on a secure and clean surface.

4

Remove all packing material.

5

Inspect the product and accessories for damage.

6 Getting Started Guide

www.dell.com | support.dell.com

Connecting a Switch to a Terminal

1

Connect the DB9 connector of the USB-to-DB9 serial cable to a VT100 terminal or to a

computer running VT100 terminal emulation software.

2

Connect the USB connector at the other end to the USB port on the switch.

NOTE: If you are installing a stack of switches, connect the terminal to the Master Switch. When a stack

is powered up for the first time, the switches elect the Master Switch, which may occupy any location in

the stack. If you connect the terminal to a member (non-Master) switch, you will not be able to use the

command line interface (CLI).

Assembling a Stack

The software supports up to 12 stacked switches, supporting up to 576 1G ports. Each

PowerConnect M6348 switch provides two stacking ports at the bottom of the switch.

CAUTION: Ensure that a switch is turned off before adding it to the stack.

Use the 1-meter stacking cables to connect the stacking ports in the following manner:

1

Insert a stacking cable in the bottom stacking port on the first switch.

2

Connect the cable to the upper stacking port on the next switch.

3

Continue connecting each switch to the next until all switches are connected in a ring.

4

On the last switch in the stack, connect the cable to the upper stacking port on the first

switch to create a loop.

If necessary, use a separately purchased 3-meter stacking cable to connect the last switch to

the first.

Figure 1 shows a chassis with six connected M6348 switches.

Getting Started Guide 7

Figure 1. Connecting a Stack of Switches

NOTE: The resulting ring topology allows the entire stack to function as a single switch with resilient

fail-over capabilities.

stacking cable

upper and lower

stacking ports

8 Getting Started Guide

www.dell.com | support.dell.com

Starting and Configuring the Switch

After completing all external connections, connect a terminal to a switch to configure the switch

or stack. Additional advanced functions are described in the

User's Guide

located on your

User Documentation

CD.

NOTE: Read the release notes for this product before proceeding. You can download the release notes

from the Dell Support website at support.dell.com.

NOTE: We recommend that you obtain the most recent version of the user documentation from the Dell

Support website at support.dell.com.

Connecting the Terminal to the Switch

To monitor and configure the switch via serial console, use the console port on the rear of the

switch to connect it to a VT100 terminal or to a computer running VT100 terminal emulation

software. The console port is implemented as a data terminal equipment (DTE) connector.

The following is required to use the console port:

• VT100-compatible terminal or a desktop or a portable system with a serial port, running

VT100 terminal emulation software.

• A serial cable (provided) with a USB type A connector for the console port and DB9

connector for the terminal.

Perform the following tasks to connect a terminal to the switch console port:

NOTE: If you are installing a stack of switches, you need to assemble and cable the stack before

powering up and configuring it.

1

Connect the DB9 connector on the serial cable to the terminal running VT100 terminal emulation

software.

2

Configure the terminal emulation software as follows:

a

Select the appropriate serial port (serial port 1 or serial port 2) to connect to the console.

b

Set the data rate to 9600 baud.

c

Set the data format to 8 data bits, 1 stop bit, and no parity.

d

Set the flow control to none.

e

Set the terminal emulation mode to

VT100

.

f

Select Terminal keys for Function, Arrow, and Ctrl keys. Make sure that the setting is for

Terminal keys (not Microsoft

®

Windows

®

keys).

NOTE: When using HyperTerminal with Microsoft Windows 2000, make sure that you have Windows

2000 Service Pack 2 or later installed. With Windows 2000 Service Pack 2, the arrow keys function

properly in HyperTerminal's VT100 emulation. Go to www.microsoft.com for more information on

Windows 2000 service packs.

Getting Started Guide 9

3

Connect the USB type A connector on the USB cable directly to the switch USB console port.

The PowerConnect M6348 USB console port is located on the left side of the rear panel, as

shown in Figure 2.

NOTE: If you are installing a stack of switches, connect the terminal to the Master Switch. When a stack

is powered up for the first time, the switches elect the Master Switch, which may occupy any location in

the stack. If you connect the terminal to a member switch, you will not be able to use the CLI.

Figure 2. Connecting to the Console Port

Booting the Switch

Refer to the

Hardware Owner’s Manual

for instructions on booting the switch.

Initial Configuration

NOTE: The initial simple configuration procedure is based on the following assumptions:

• The PowerConnect switch was never configured before and is in the same state as when you

received it.

• The PowerConnect switch booted successfully.

• The console connection was established and the Dell Easy Setup Wizard prompt appears on the

screen of a VT100 terminal or terminal equivalent.

The initial switch configuration is performed through the console port. After the initial

configuration, you can manage the switch either from the already-connected console port or

remotely through an interface defined during the initial configuration.

NOTE: The switch is not configured with a default user name and password.

NOTE: All of the settings below are necessary to allow the remote management of the switch through

Telnet (Telnet client) or HTTP (Web browser).

console port

10 Getting Started Guide

www.dell.com | support.dell.com

Before setting up the initial configuration of the switch, obtain the following information from

your network administrator:

• The IP address to be assigned to the management VLAN.

• The IP subnet mask for the network.

• The IP address of the management VLAN default gateway.

Initial Configuration Procedure

You can perform the initial configuration using the Dell Easy Setup Wizard, or by using the

Command Line Interface (CLI). The Setup Wizard automatically starts when the switch

configuration file is empty. You can exit the wizard at any point by entering [ctrl+z], but all

configuration settings specified will be discarded (the switch will use the default values).

For more information on CLI initial configuration see the

User Guide

. This

Getting Started Guide

shows how to use the Setup Wizard for initial switch configuration. The wizard sets up the following

configuration on the switch:

• Establishes the initial privileged user account with a valid password. The wizard configures

one privileged user account during the setup.

• Enables CLI login and HTTP access to use the local authentication setting only.

• Sets up the IP address for the management VLAN.

• Sets up the SNMP community string to be used by the SNMP manager at a given IP address.

You may choose to skip this step if SNMP management is not used for this switch.

• Allows you to specify the management server IP or permit management access from all IP

addresses.

• Configures the default gateway IP address.

Example Session

This section describes an Easy Setup Wizard session. The following values are used by the example

session:

• The SNMP community string to be used is

DellNetworkManager

.

• The network management system IP address is

192.168.2.1

.

• The user name is

admin

, and password is

admin123

.

• The IP address for the management VLAN is

192.168.2.1:255.255.255.0

.

• The default gateway is

0.0.0.0

.

Getting Started Guide 11

The setup wizard configures the initial values as defined above. After you complete the wizard,

the switch is configured as follows:

• SNMPv1/2c is enabled and the community string is set up as defined above. SNMPv3 is

disabled by default.

• The admin user account is set up as defined.

• A network management system is configured. From this management station, you can access

the SNMP, HTTP, and CLI interfaces. You may also choose to allow all IP addresses to access

these management interfaces by choosing the (0.0.0.0) IP address.

• An IP address is configured for the default management VLAN (1).

• A default gateway address is configured.

NOTE: In the example below, the possible user options are enclosed in [ ]. Also, where possible, the

default value is provided in { }. If you press <Enter> with no options defined, the default value is accepted.

Help text is in parentheses.

The following example contains the sequence of prompts and responses associated with running an

example Dell Easy Setup Wizard session, using the input values listed above.

After the switch completes the POST and is booted, the following dialog appears:

Unit 1 - Waiting to select management unit)>

Applying configuration, please wait ...

Welcome to Dell Easy Setup Wizard

The Setup Wizard guides you through the initial switch

configuration, and gets you up and running as quickly as possible.

You can skip the setup wizard, and enter CLI mode to manually

configure the switch. You must respond to the next question to run

the setup wizard within 60 seconds, otherwise the system will

continue with normal operation using the default system

configuration.Note: You can exit the setup wizard at any point by

entering [ctrl+z].

Would you like to run the setup wizard (you must answer this

question within 60 seconds)? [Y/N] y

Step 1:

The system is not setup for SNMP management by default. To manage

the switch using SNMP (required for Dell Network Manager) you can

. Set up the initial SNMP version 2 account now.

. Return later and setup other SNMP accounts. (For more

information on setting up an SNMP version 1 or 3 account, see

the user documentation).

Would you like to setup the SNMP management interface now? [Y/N] n

12 Getting Started Guide

www.dell.com | support.dell.com

Step 2:

Now we need to setup your initial privilege (Level 15) user

account. This account is used to login to the CLI and Web

interface. You may setup other accounts and change privilege

levels later. For more information on setting up user accounts and

changing privilege levels, see the user documentation.

To setup a user account:

Please enter the user name. [root]:root

Please enter the user password:********

Please reenter the user password:********

Step 3:

Next, an IP address is setup. The IP address is defined on the

default VLAN (VLAN #1), of which all ports are members. This is the

IP address you use to access the CLI, Web interface, or SNMP

interface for the switch. Optionally you may request that the

system automatically retrieve an IP address from the network via

DHCP (this requires that you have a DHCP server running on the

network).

To setup an IP address:

Please enter the IP address of the device (A.B.C.D) or enter "DHCP"

(without the quotes) to automatically request an IP address from

the network DHCP server. [192.168.2.1]:192.168.2.1

Please enter the IP subnet mask (A.B.C.D or /nn).

[255.255.255.0]:255.255.255.0

Step 4:

Finally, setup the default gateway. Please enter the IP address of

the gateway from which this network is reachable. [0.0.0.0]:

This is the configuration information that has been collected:

User Account setup = root

Password = ********

Management IP address = 192.168.2.1 255.255.255.0

Default Gateway = 0.0.0.0

Step 5:

Do you want to select the operational mode as Simple Mode? [Y/N] n

Getting Started Guide 13

Step 6:

If the information is correct, please select (Y) to save the

configuration, and copy to the start-up configuration file. If the

information is incorrect, select (N) to discard configuration and

restart the wizard: [Y/N] y

Thank you for using Dell Easy Set up Wizard. You will now enter CLI

mode.

Managing a Stack

Master and Member Switches

A stack of switches can be managed as a single entity when connected together. The stack can be

managed from a web-based interface, an SNMP management station, or a CLI. When a stack is

created, one switch automatically becomes the master switch. You can manually allocate an IP

address to the master switch using the console, or let DHCP do so automatically. Afterwards,

you can manage the entire stack through the IP address of the Master Switch. The Master Switch

detects and reconfigures the ports with minimal operational impact in the event of:

• Switch failure

• Inter-switch stacking link failure

• Switch insertion

• Switch removal

If the Master Switch goes off line, any of the Member Switches in the stack can replace it.

The system will elect a new Master Switch and reconfigure the System Configuration for the stack.

Stack Startup

Topology Discovery

When a stack is formed, a topology discovery process builds up a database that contains

information about all of the switches in the stack, including the Firmware Version, Hardware

Version, Management Preference, Switch MAC Address, and Switch Serial Number. You can use

the command line interface (CLI) or the Web interface to view this information.

NOTE: See the CLI Reference Manual and the User’s Guide for assistance with the CLI and Web

interface, respectively.

14 Getting Started Guide

www.dell.com | support.dell.com

Auto Stack ID Assignment

During the stack formation process, every switch is assigned a Stack ID. Once Stack ID assignment

is complete, each switch saves its Stack ID into the nonvolatile FLASH memory. You can use the

CLI or the Web interface to view the stack IDs.

Firmware Version Checking

Following Stack ID assignment, the Master Switch performs a consistency check to make sure that

all switches in the stack are running the same firmware version.

If the switch software versions do not match, then the ports on the member switch will not become

valid for operation. This condition is known as the Suspended Stacking Mode. You can then

synchronize the firmware on the member switch with the firmware that is running on the Master

Switch.

System Initialization

If the Master Switch determines during the firmware version consistency check that all switches are

running the same version of firmware, the switch will be initialized for Stacking Mode.

System Initialization for Normal Stacking Mode

The Master Switch will initialize the stack using the last saved system configuration file. For those

switches that do not have a configuration file, the system will apply default settings to those

switches.

If the configuration file is corrupted, the Master Switch will initialize the stack and set it to the

Factory Default Configuration.

You can save the configuration file. The Master Switch automatically distributes the configuration

file to the member switches. If the Master Switch later becomes unavailable, a Member Switch

becomes the new Master Switch and configures the stack with the latest configuration

synchronized from the Master Switch.

System Initialization for Suspended Stacking Mode

After system initialization is complete, the Master Switch will enter Suspended Stacking Mode if

the firmware versions of the stack are inconsistent. In this mode, only the Master Switch is

initialized with configuration file information. None of the member switches are initialized.

This forces all member switches to remain in non-operational mode.

NOTE: All ports disabled by default.

Getting Started Guide 15

CLI/ Telnet/ Web Interface

You can use the CLI / WEB / SNMP to synchronize the firmware that is stored in the Master

Switch to a member switch.

Insertion and Removal of Switches

You can insert and remove switches to/from the current stack without cycling the power. The entire

network may be affected when a topology change occurs, as a stack reconfiguration will take place.

A new Master Switch will not be re-elected, unless the Master Switch was removed from the stack.

Stack reconfiguration takes a maximum of two minutes in a stack of twelve switches, less time for

smaller stacks.

Operating as Standalone Switch

If a switch cannot detect a stacking partner on a port enabled for stacking, the switch will operate

as a standalone switch. If a stacking partner is detected, the switch will always operate in stacking

mode.

Stack ID Renumbering

You can manually assign Stack IDs to a switch. A switch can only be assigned a Stack ID that has

not already been assigned to another switch in the stack. Any configuration information that was

saved for the new Stack ID is applied to the switch that is taking that Stack ID.

User Controls

Use the following CLI commands to control this feature. See the

CLI Reference Manual

for details

on the syntax of each command.

movemanagement

reload

member

set description

switch priority

switch renumber

stacking

show stack-port

show stack-port counters

show stack-port diag

show switch

show supported switchtype

16 Getting Started Guide

www.dell.com | support.dell.com

Advanced Configuration

This section provides summary information about such common tasks as:

• Retrieving an IP Address From a DHCP Server

• Security Management and Password Configuration

NOTE: For detailed information on all the CLI commands available for the 8024 and 8024F M6348

switches, see the CLI Reference Guide.

Retrieving an IP Address From a DHCP Server

When using the DHCP protocol to retrieve an IP address, the switch acts as a DHCP client.

To retrieve an IP address from a DHCP server, perform the following steps:

1

Select and connect any port to a DHCP server or to a subnet that has a DHCP server on it,

in order to retrieve the IP address.

NOTE: You do not need to delete the switch configuration to retrieve an IP address for the D HCP server.

2

Enter the following commands to use the selected port for receiving the IP address.

console#config

console(config)#ip address dhcp

The interface receives the IP address automatically.

3

To verify the IP address, enter the show ip interface command at the system prompt as shown

in the following example.

console#show ip interface

Management Interface:

IP Address....................................... 10.240.4.125

Subnet Mask..................................... 255.255.255.0

Default Gateway.................................... 10.240.4.1

Burned In MAC Address........................00:10:18:82:04:35

Network Configuration Protocol Current................... DHCP

Management VLAN ID.......................................... 1

Getting Started Guide 17

Routing Interfaces:

Netdir Multi

Interface IP Address IP Mask Bcast CastFwd

---------- --------------- --------------- -------- --------

vlan1 192.168.10.10 255.255.255.0 Disable Disable

vlan2 0.0.0.0 0.0.0.0 Enable Disable

loopback2 0.0.0.0 0.0.0.0 Disable Disable

Security Management and Password Configuration

System security is handled through the AAA (Authentication, Authorization, and Accounting)

mechanism that manages user access rights, privileges, and management methods. AAA uses both

local and remote user databases. Data encryption is handled through the SSH mechanism.

The system is delivered with no default password configured; all passwords are user-defined. If a

user-defined password is lost, a password recovery procedure can be invoked from the Boot menu.

The procedure is applicable for the local terminal only and allows a one-time access to the switch

from the local terminal with no password entered.

Configuring Security Passwords

The security passwords can be configured for the following services:

• Console

• Telnet

• SSH

•HTTP

•HTTPS

NOTE: When creating a user name, the default priority is "1", which allows access but not configuration

rights. A priority of "15" must be set to enable access and configuration rights to the switch.

18 Getting Started Guide

www.dell.com | support.dell.com

Configuring an Initial Console Password

To configure an initial console password, enter the following commands:

console(config)#aaa authentication login default line

console(config)#aaa authentication enable default line

console(config)#line console

console(config-line)#login authentication default

console(config-line)#enable authentication default

console(config-line)#password secret123

• When initially logging on to a switch through a console session, enter

secret123

at the

password prompt.

• When changing a switch’s mode to enable, enter

secret123

at the password prompt.

Configuring an Initial Telnet Password

To configure an initial Telnet password, enter the following commands:

console(config)#aaa authentication login default line

console(config)#aaa authentication enable default line

console(config)#line telnet

console(config-line)#login authentication default

console(config-line)#enable authentication default

console(config-line)#password pass1234

• When initially logging onto a switch through a Telnet session, enter

pass1234

at the

password prompt.

• When changing a switch mode to enable, enter

pass1234

.

Configuring an Initial HTTP Password

To configure an initial HTTP password, enter the following commands:

console(config)#ip http authentication local

console(config)#username admin password user1234 level 15

ページを読み込んでいます...

Dell PowerConnect M6348 クイックスタートガイド

関連論文