Roland DAP-3 取扱説明書

タイプ
取扱説明書

このマニュアルも適しています

1
03896189 1TM
Owner’s Manual
Thank you, and congratulations on your
choice of the Roland Kick Pedal KP-250.
202
Copyright © 2004 ROLAND CORPORATION
All rights reserved. No part of this publication may
be reproduced in any form without the written
permission of ROLAND CORPORATION.
Part Names
962a
* In the interest of product improvement, the specifications
and/or appearance of this unit are subject to change
without prior notice.
Before using this unit, carefully read the
sections entitled: “USING THE UNIT SAFELY”
and “IMPORTANT NOTES” (back page). These
sections provide important information
concerning the proper operation of the unit.
Additionally, in order to feel assured that you
have gained a good grasp of every feature
provided by your new unit, Owner’s Manual
should be read in its entirety. The manual
should be saved and kept on hand as a
convenient reference.
Roller
Square-Headed Bolt
Square-Headed Bolt
Spring
Angle Memory Cap
3
Footboard
Beater
Beater Holder
2
1
Lock Nut
Adjusting Nut
Hoop Clamp
Installing the Beater
1.
Loosen the square-headed bolt of the beater
holder using a drum key.
2.
Insert the beater shaft and tighten the square-
headed bolt to secure it.
* The beater head has two sides, felt and nylon. Use the
nylon side for mesh head (KD-120, KD-80). The felt
side is recommended for KD-8 for more silence.
Attaching the Pedal Unit
The pedal unit is attached to the kick trigger.
For details on how to attach the pedal unit,
refer to the owner’s manual for your kick
trigger.
Adjusting the Beater Angle
The angle of the beater can be adjusted along
with the angle of the footboard by loosening the
square-headed bolt on top of the rocker cam.
You may test the gradations of the Angle
memory cap, attached to the end of the shaft, by
adjusting it a bit at a time.
Once the desired angle is reached, tighten the
bolt firmly to secure it.
Adjusting the Spring
1.
Hang the spring on the roller of the rocker
cam.
2.
Adjust the spring tension using the nut on the
lower end.
When adjusting the spring, first loosen the lock
nut (Fig. 1), and then turn the adjusting nut while
pressing down on the lock nut as in Fig. 2.
Tightening the nut makes the pedal’s resistance
heavier, but the beater’s return time is
correspondingly faster.
In order to prevent the spring from loosening
while playing, the adjusting nut engages the cap
attached to the unit roughly every 1/3 of a turn.
3.
Once the desired tension is reached, secure it by
tightening the lock nut as in Fig. 3.
1
1
2
3
Spring
Loosen
Fig. 1 Fig. 2 Fig. 3
Lock Nut
Cap
Adjusting Nut
TightenPress down
©
1.
2.
1.
2.
3.
1
1
2
3
KP-250_je 1 ページ 2004年11月25日 木曜日 午後1時22分
2
USING THE UNIT SAFELY
001
Before using this unit,
make sure to read the
instructions below, and
the Owner’s Manual.
...............................................................
002a
Do not open or perform
any internal modifications
on the unit.
...............................................................
003
Do not attempt to repair
the unit, or replace parts
within it (except when this
manual provides specific
instructions directing you
to do so). Refer all
servicing to your retailer,
the nearest Roland Service
Center, or an authorized
Roland distributor, as
listed on the “Infor-
mation” page.
...............................................................
004
Never use or store the unit
in places that are:
Subject to temperature
extremes (e.g., direct
sunlight in an enclosed
vehicle, near a heating
duct, on top of heat-
generating equipment);
or are
Damp (e.g., baths,
washrooms, on wet
floors); or are
Humid; or are
Exposed to rain; or are
Dusty; or are
Subject to high levels of
vibration.
...............................................................
007
Make sure you always
have the unit placed so it
is level and sure to remain
stable. Never place it on
stands that could wobble,
or on inclined surfaces.
................................................................
013
In households with small
children, an adult should
provide supervision until
the child is capable of
following all the rules
essential for the safe
operation of the unit.
................................................................
014
Protect the unit from
strong impact.
(Do not drop it!)
................................................................
106
Never climb on top of, nor
place heavy objects on the
unit.
................................................................
118a
Should you remove the
square-headed bolts, keep
them in a safe place out of
children’s reach, so there is
no chance of them being
swallowed accidentally.
................................................................
add
There is a risk of injury if
the kick pedal is used
barefoot. Please wear
suitable footwear.
................................................................
IMPORTANT
NOTES
291a
In addition to the items listed under
“USING THE UNIT SAFELY” on this
page, please read and observe the
following:
Maintenance
402
Never use benzine, thinners,
alcohol or solvents of any kind, to
avoid the possibility of discolor-
ation and/or deformation.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
KP-250_je 2 ページ 2004年11月25日 木曜日 午後1時22分
  • Page 1 1
  • Page 2 2

Roland DAP-3 取扱説明書

タイプ
取扱説明書
このマニュアルも適しています

他の言語で