充电指示
电池电量不足
S586： 当电池电量几乎耗尽时，
电池充电指示灯的底灯会呈橙色
闪烁 (图 5)。
S566
： 当电池的电量几乎耗尽时，
电池充电指示灯会呈橙色闪烁。
电池正在充电
S586： 产品充电时，电池充电
指示灯的底灯先是闪烁，然后
持续 (图 6)亮起。 然后，第二
个指示灯闪烁，之后持续亮
起，以此类推，直至本产品充
满电。
S566： 产品充电时，电池充电
指示灯呈白色闪烁。
电池电量充满
S586： 电池充满电后，所有电
池充电指示灯都将呈白色持续
(图 7)亮起。
S566： 电池充满电后，电池充
电指示灯将呈白色持续亮起。
使用剃须刀
注意： 本产品只能在不接电源
的情况下使用。
“使用前拔掉电源插头”提醒
S586： 电池充电指示灯的所有
灯闪烁 3 次，提醒您先拔掉剃
须刀的电源插头。
S566： 电池充电指示灯短暂地
快速闪烁，提醒您先拔掉剃须
刀的电源插头。
使用本产品
拆卸或安装卡入式附件
1 确保产品电源已关闭。
2 将附件的凸缘插入本产品顶
部的槽内。 然后，按下附件
将其安装到本产品上（可听
到“咔哒”一声） (图 8)。
3
将附件竖直抽离产品 (图 9)。
注意： 将附件从产品上抽出
时，不要旋转。
打开或关闭产品
1 要打开或关闭本产品，请按
一下 (图 10)开/关按钮。
使用剃须刀
注意： 本产品只能在不接电源
的情况下使用。
剃须
皮肤适应期
前几次剃须可能不会带给您预期
效果，并且您的皮肤可能会受到
轻度刺激。 这是正常的。 您的
皮肤和胡须需要时间适应任何新
的剃须系统。 为了让您的皮肤适
应这款新产品，我们建议您在 3
周时间内定期（至少每周 3 次）
仅使用本产品剃须。
干剃
1 启动产品。
2 让剃须刀头在您的皮肤上作
迂回运动，以刮剃向不同方
向 (图 11)生长的所有须发。
轻轻按压，以获取舒适贴面
的剃须感受。
注意： 不要用力按压剃须刀，
这样做可能会导致皮肤受刺
激。
3 使用 (请参见 '清洁和保养‘)
后要清洁本产品。
湿剃
您可以先用剃须泡沫或剃须啫
喱将脸弄湿，然后再用本产品
进行剃须。
要用剃须泡沫或剃须啫喱剃须，
请按照下面的步骤执行操作：
1 用水润湿皮肤。
2 在皮肤上涂抹剃须泡沫或剃
须啫喱。
3
在水龙头下冲洗一下剃须刀头
部件，确保剃须刀头部件可以
在您的皮肤上顺畅滑动。
4 启动产品。
5 让剃须刀头在您的皮肤上作
迂回运动，以刮剃向不同方
向 (图 11)生长的所有须发。
轻轻按压，以获取舒适贴面
的剃须感受。
注意： 不要用力按压剃须
刀，这样做可能会导致皮肤
受刺激。
注意： 定期冲洗剃须刀头部
件，确保其能够持续在您的
皮肤上顺畅滑动。
6 擦干面部。
7 使用 (请参见 '清洁和保养‘)
后要清洁本产品。
注意： 确保冲洗干净本产品
上的所有泡沫或剃须啫喱。
清洁和保养
在水龙头下冲洗剃须刀
每次剃须后请清洁剃须刀，以获
得出色性能 (请参见 ‚清洁和保
养‘)。清洁前，务必拔下电源
并关闭剃须刀。
切勿使用压缩气体、钢丝绒、
研磨性清洁剂或腐蚀性液体
（例如汽油或丙酮）清洁本产
品。
使用热水要当心。 切记先检查
水温是否太高，以防烫手。
不要用毛巾或纸巾擦拭剃须刀
头部件，因为这样可能会损坏
剃须刀头。
1 用温水冲洗剃须刀头部件。
注意： 您也可以使用随附的
(图 12)清洁刷清洁剃须刀头
部件.
2 将剃须刀倒置，冲洗剃须刀
头支架底部的开口。 在冲洗
(图 13)过程中需短暂开启剃
须刀。
3 打开两个剃须刀头支架
(图 14)。
4 在水龙头 (图 15)下冲洗胡茬
储藏室和剃须刀头支架。
5 小心地甩掉多余的水份然后
彻底晾干。
6 合上剃须刀头支架 (图 16)。
彻底清洁
剃须刀头部件包含两个剃须刀
头。 按以下步骤一次清洁一个
剃须刀头。
1 打开剃须刀头支架 (图 14)。
2 要解锁固定架，请轻轻挤压
固定架的两侧，然后翻开固
定架 (图 17)。
3 取下剃须刀头。 每个剃须刀
头包含一组刀片和网罩
(图 18)。
注意： 不要同时清洁多组刀
片和网罩，因为它们都是相
互匹配的。 如果不小心将剃
须刀头的刀片和网罩弄混，
则需要数周时间才能恢复产
品的最佳剃须效果。
4 从网罩 (图 19)上取下刀片。
5 用清水冲洗这两个部件。
6
清洁后，将刀片重新装回至网
罩，刀片底部朝下 (图 20)。
7 将剃须刀头装回到剃须刀头
支架 (图 21)中。
注意： 安装剃须刀头 (图 23)
时，确保带凸起的剃须刀头
正好卡入剃须刀头支架的挂
钩。 本产品随附的剃须刀头
都带有槽口或凸起。 这两组
剃须系统完全相同。
8 将固定架推回到剃须刀头支
架上，直至听到“咔哒”
(图 22)一声。
9 合上剃须刀头支架 (图 16)。
更换
更换剃须刀头
为获得最佳剃须效果，建议每
两年更换一次剃须刀头。立即
更换损坏的剃须刀头。 务必使
用原装飞利浦剃须刀头 (请参见
‚订购配件‘)进行更换。
8 用钢丝钳 (图 31)剪断连接马
达的电线，并卸下印刷电路
板 (图 32)。
9 撕开电池标签并取出电池
(图 33)。
故障种类和处理方法
本章归纳了使用本产品时最常
见的一些问题。如果您无法根
据以下信息解决问题，请访问
www.philips.com/support 查阅
常见问题列表，或联系您所在
国家/地区的客户服务中心。
问题 可能的
原因
解决方法
剃须刀
的剃须
效果没
有以前
好。
剃须刀
头已损
坏或磨
损。
更换剃须
刀头 (请参
见 '更换')
。
剃须刀
头很
脏。
清洁剃须
刀头 (请参
见 '清洁和
保养')。
较长的
胡须堵
塞了剃
须刀
头。
清洁剃须
刀头 (请参
见 '清洁和
保养')。
充电电
池的电
量不
足。
关闭剃须
刀并为电
池 (请参见
'充电')充
电。
启动剃
须刀
后，剃
须刀无
法工
作。
充电电
池的电
量已耗
尽。
关闭剃须
刀并为电
池 (请参见
'充电')充
电。
剃须刀
连接了
电源插
座。
本产品只
能在不接
电源的情
况下使
用。 从电
源插座上
拔下电源
部件，并
从剃须刀
上拔下小
插头。
剃须刀
头无法
固定在
剃须刀
头部件
内。
未正确
固定固
定架。
将固定架
推回剃须
刀头上
时，听
到“咔
哒”一声
后，即表
明固定架
已固定到
位。
未正确
放置带
有凸起
部位的
剃须刀
头。
安装剃须
刀头 (图
23)时，确
保带凸起
的剃须刀
头正好卡
入剃须刀
头支架的
挂钩。
保留备用
发行日期: 05/05/2017
1 关闭产品。
2 打开两个剃须刀头支架 (图
14)，即打开剃须刀头部件。
3 要解锁固定架，请轻轻挤压
固定架的两侧，然后翻开剃
须刀头 (图 17)。
4 从剃须刀头支架 (图 18)上卸
下剃须刀头。
立即扔掉用过的剃须刀头，
以免与新的剃须刀头混淆。
5 将新的剃须刀头装到剃须刀
头支架中。
注意： 安装剃须刀头 (图 23)
时，确保带凸起的剃须刀头
正好卡入剃须刀头支架的挂
钩。 本产品随附的剃须刀头
都带有槽口或凸起。 这两组
剃须系统完全相同。
6 将固定架推回到剃须刀头支
架上，直至听到“咔哒”
(图 22)一声。
7 合上剃须刀头支架 (图 16)。
存放
务必将保护盖滑到剃须刀头部
件上，以防止剃须刀头部件积
聚灰尘，或在旅行过程中或存
放 (图 24)时受损。
我们建议您先将产品晾干，
然后再进行存放。
订购配件
要购买附件或备件，请访问
www.shop.philips.com/service
或联系您的飞利浦经销商。 您
还可以联系所在国家/地区的飞
利浦客户服务中心（请参阅全球
保修卡了解详细联系信息）。
可用部件
可选配以下附件和备件：
- SH30 飞利浦剃须刀头
- RQ575 飞利浦洁面刷附件
- RQ563 飞利浦洁面刷附件
（三件装）
- HQ110 清洁喷雾剂
- HQ8505 电源部件
注意： 附件可能因国家/地区
而异。
回收
- 弃置本产品时，请不要将其与
一般生活垃圾放在一起，应将
其交给政府指定的回收中心。
这样做将有利于环保。
- 此产品包含内置充电电池；
请勿将充电电池与一般生活
垃圾一起弃置。 强烈建议您
将自己的产品送到官方收集
点或飞利浦服务中心，让专
业人士移除充电电池。
- 遵循您的国家/地区有关分类
回收电子电气产品和充电电
池的规定。 正确弃置产品有
助于避免对环境和人类健康
造成不良后果。
拆下充电电池
仅在丢弃剃须刀时方可取出充
电电池。 卸下电池之前，请确
保剃须刀与电源断开连接并且
电池电量已耗尽。
当您使用工具打开剃须刀时，
请采取必要的安全保护措施。
注意，电池带非常锋利。
1 断开本产品电源并让其继续
运行，直到马达停止。
2 将螺丝刀插入前面板的上侧
边缘，卸下面板 (图 25)。
3 拧下剃须刀 (图 26)顶部的
螺丝。
4 取下盖子 (图 27)。
5 将螺丝刀插入前面板的下侧
边缘，卸下面板 (图 28)。
6 用螺丝刀 (图 29)卸下内层
面板。
7 用螺丝刀 (图 30)将内层固定
架从外壳中推出。
- 该表格中所显示的“有害物质”在产品正常使用情况下不会对人
身和环境产生任何伤害。
- 该表格中所显示的“有害物质”及其存在的部件向消费者和回收
处理从业者提供相关物质的存在信息，有助于产品废弃时的妥善
处理。
мȞġĈҴˀΙĀǩ؆Ӎߒʔ
ˌɫǩ؆
ĈҴˀΙ
(Pb)
᰽
(Hg)
⬡
(Cd)
ԣ͍Ჱ
(Cr (VI) )
Ġ⅑ԓ᧠
(PBB)
Ġ⅑ȕ᧠⓭
(PBDE)
PCB’s
מŪǗɢذ
XOOO
OO
Electrical
contact pins
ǗˈਝǦ
XOOO
OO
Power plug
Ǘ۷Ǽ
XOOO
OO
ǕȪϜ֪֙SJ/T 11364Āܪǭৠ̑뺯
OȪФ˽ĈҴˀΙć˽ˌɫǨĈߴΙࠒնġĀߒʔߴćGB/T 26572ܪǭĀՄʔđ̂ŘĪ뺯
XȪФ˽ĈҴˀΙψɺć˽ˌɫĀԚĂߴΙࠒնġĀߒʔɸŜGB/T 26572ܪǭĀՄʔđ̂
뺯
4222.002.7319.1
www.philips.com
>75% recycled paper
>75%
S586 S566
1
2
3
4
5
6
7
8
9
10
11
12
1
2
1
1
18
21
24
19
22
25
27 28
30 31
2
5
8
11
14
17
20
23
26
29
1
2
3
6
9
12
4
7
10
13
15 16
S586, S566
4222_002_7319_1_DFU-Leaflet_55x99_6x4_v1.indd 1 05/05/17 11:31
ENGLISH
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips oers, register
your product at www.philips.com/
welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving head holder
3 Shaving unit connector
4 Handle
5 Battery charge indicator
6 On/o button
7 Socket for small plug
8 Cutter
9 Guard
10 Retaining frame
11 Supply unit
12 Small plug
Not shown: cleaning brush
Important safety
information
Read this important information
carefully before you use the appliance
and its accessories and save it for future
reference. The accessories supplied may
vary for dierent products.
Danger
- Keep the supply unit dry (Fig. 2).
Warning
- To charge the battery, only use the
detachable supply unit (HQ8505)
provided with the appliance.
- The supply unit contains a
transformer. Do not cut o the
supply unit to replace it with
another plug, as this causes a
hazardous situation.
- This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe
way and understand the hazards
involved. Children shall not play with
the appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
- Always unplug the shaver before
you clean it under the tap.
- Always check the appliance before
you use it. Do not use the appliance
if it is damaged, as this may cause
injury. Always replace a damaged
part with one of the original type.
- Do not open the appliance to
replace the rechargeable battery.
Caution
- Never use water hotter than 60°C to
rinse the shaver.
- Only use this appliance for its
intended purpose as shown in the
user manual.
- For hygienic reasons, the appliance
should only be used by one person.
- Never use compressed air, scouring
pads, abrasive cleaning agents or
aggressive liquids such as petrol or
acetone to clean the appliance.
- Water may drip from the bottom of
the shaver when you rinse it. This is
normal and not dangerous because
all electronics are enclosed in a
sealed power unit inside the shaver.
- Do not use the supply unit in or near
wall sockets that contain an electric
air freshener to prevent irreparable
damage to the supply unit.
Electromagnetic elds (EMF)
- This Philips appliance complies
with all applicable standards and
regulations regarding exposure to
electromagnetic elds.
General
- This shaver is waterproof (Fig. 3).
It is suitable for use in the bath or
shower and for cleaning under the
tap. For safety reasons, the shaver
can therefore only be used without
cord.
- The appliance is suitable for mains
voltages ranging from 100 to 240 volts.
- The supply unit transforms 100-
240 volts to a safe low voltage of
less than 24 volts.
Charging
Note: This appliance can only be used
without cord.
Charge the appliance before rst use
and when the display indicates that
the battery is almost empty.
Charging takes approx. 1 hour.
A fully charged shaver provides up to
45 minutes of shaving time.
Charging with the supply unit
1 Put the small plug in the shaver.
2 Put the supply unit in the wall
socket (Fig. 4).
3 After charging, remove the supply
unit from the wall socket and pull
the small plug out of the appliance.
Charge indications
Battery low
S586: When the battery is almost
empty, the bottom light of the battery
charge indicator ashes orange (Fig. 5).
S566: When the battery is almost
empty, the battery charge indicator
ashes orange.
Battery charging
S586: When the appliance is charging,
the bottom light of the battery charge
indicator rst ashes and then lights
up continuously (Fig. 6). After this the
second light ashes and then lights
up continuously, and so on until the
appliance is fully charged.
S566: When the appliance is charging,
the battery charge indicator ashes white.
Battery full
S586: When the battery is fully charged,
all lights of the battery charge indicator
light up white continuously (Fig. 7).
S566: When the battery is fully
charged, the battery charge indicator
lights up white continuously.
Note: This appliance can only be used
without cord.
‚Unplug before use‘ reminder
S586: All lights of the battery charge
indicator ash 3 times to remind you to
unplug the shaver rst.
S566: The battery charge indicator
ashes fast briey to remind you to
unplug the shaver rst.
Using the appliance
Removing or attaching the
click-on attachments
1 Make sure the appliance is
switched o.
2 Insert the lug of the attachment into
the slot in the top of the appliance.
Then press down the attachment
to attach it to the appliance (‘click’)
(Fig. 8).
3 Pull the attachment straight o the
appliance (Fig. 9).
Note: Do not twist the attachment
while you pull it o the appliance.
Switching the appliance on
and o
1
To switch the appliance on or o,
press the on/o button once (Fig. 10).
Note: This appliance can only be used
without cord.
Shaving
Skin adaptation period
Your rst shaves may not bring you the
result you expect and your skin may
even become slightly irritated. This is
normal. Your skin and beard
need time to adapt to any new shaving
system. To allow your skin to adapt
to this new appliance, we advise you
to shave regularly (at least 3 times
a week) and exclusively with this
appliance for a period of 3 weeks.
Dry shaving
1 Switch on the appliance.
2
Move the shaving heads over your
skin in circular movements to catch
all hairs growing in dierent directions
(Fig. 11). Exert gentle pressure for a
close, comfortable shave.
Note: Do not press too hard, as this
can cause skin irritation.
3 Clean the appliance after use
(see ‚Cleaning and maintenance‘).
Wet shaving
You can also use this appliance on a wet
face with shaving foam or shaving gel.
To shave with shaving foam or shaving
gel, follow the steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel
to your skin.
3 Rinse the shaving unit under the
tap to ensure that the shaving unit
glides smoothly over your skin.
4 Switch on the appliance.
5
Move the shaving heads over your
skin in circular movements to catch
all hairs growing in dierent directions
(Fig. 11). Exert gentle pressure for a
close, comfortable shave.
Note: Do not press too hard, this
can cause skin irritation.
Note: Rinse the shaving unit
regularly to ensure that it continues
to glide smoothly over your skin.
6 Dry your face.
7 Clean the appliance after use
(see ‚Cleaning and maintenance‘).
Note: Make sure you rinse all foam
or shaving gel o the appliance.
Storage
Always slide the protection cap onto
the shaving unit to protect the shaving
unit from dirt or damage during
traveling or storage (Fig. 24).
We advise you to let the appliance dry
before you store it.
Ordering accessories
To buy accessories or spare parts,
visit www.shop.philips.com/service
or go to your Philips dealer. You can
also contact the Philips Consumer
Care Center in your country (see
the international warranty leaet for
contact details).
Available parts
The following accessories and spare
parts are available:
- SH30 Philips shaving heads
- RQ575 Philips cleansing brush
attachment
- RQ563 Philips cleansing brush
attachment 3-pack
- HQ110 Cleaning spray
- HQ8505 supply unit
Note: Availability of the accessories
may dier by country.
Recycling
- Do not throw away the product
with the normal household waste
at the end of its life, but hand it in
at an ocial collection point for
recycling. By doing this, you help to
preserve the environment.
- This product contains a built-in
rechargeable battery which shall
not be disposed of with normal
household waste. We strongly
advise you to take your product
to an ocial collection point
or a Philips service centre to
have a professional remove the
rechargeable battery.
- Follow your country’s rules for the
separate collection of electrical
and electronic products and
rechargeable batteries. Correct
disposal helps prevent negative
consequences for the environment
and human health.
Removing the rechargeable
battery
Only remove the rechargeable
battery when you discard the shaver.
Before you remove the battery, make
sure that the shaver is disconnected
from the mains and that the battery
is completely empty.
Take any necessary safety
precautions when you handle tools
to open the shaver.
Be careful, the battery strips are sharp.
1 Disconnect the appliance from the
wall socket and let the appliance
run until the motor stops.
2 Insert a screwdriver under the
edge of the upper front panel and
remove it (Fig. 25).
3 Undo the screws in the top part of
the shaver (Fig. 26).
4 Remove the cover (Fig. 27).
5 Insert a screwdriver under the edge
of the lower front panel to remove
it (Fig. 28).
6 Remove the inner panel with a
screwdriver (Fig. 29).
7
Push the inner frame out of the
housing with the screwdriver (Fig. 30).
8 Cut the wires from the motor with
pliers (Fig. 31) and remove the
printed circuit board (Fig. 32).
9 Break the battery tags and remove
the batteries (Fig. 33).
Troubleshooting
This chapter summarizes the most
common problems you could encounter
with the appliance. If you are unable to
solve the problem with the information
below, visit www.philips.com/support
for a list of frequently asked questions
or contact the Consumer Care Center in
your country.
Cleaning and maintenance
Cleaning the shaver under the tap
Clean the shaver after every shave for
optimal performance (see ‚Cleaning
and maintenance‘). Always unplug and
switch o the shaver before you clean it.
Never use compressed air, scouring
pads, abrasive cleaning agents or
aggressive liquids such as petrol or
acetone to clean the appliance.
Be careful with hot water. Always
check if the water is not too hot, to
prevent burning your hands.
Never dry the shaving unit with a
towel or tissue, as this may damage
the shaving heads.
1 Rinse the shaving unit under a
warm tap.
Note: You can also clean the
shaving unit with the cleaning brush
supplied (Fig. 12).
2 Turn the shaver up side down and
rinse the openings in the bottom of
the shaving head holders. Switch
on the shaver briey during rinsing
(Fig. 13).
3 Open both shaving head holders
(Fig. 14).
4 Rinse the hair chambers and
shaving head holders under the tap
(Fig. 15).
5 Carefully shake o excess water
and let air dry completely.
6 Close the shaving head holders
(Fig. 16).
Thorough cleaning
The shaving unit consists of two
shaving heads. Clean one shaving
head at a time by following the steps
below.
1 Open the shaving head holder
(Fig. 14).
2
To unlock the retaining frame, gently
squeeze both sides of the retaining
frame and ip open the frame (Fig. 17).
3 Remove the shaving head. Each
shaving head consists of a cutter
and a guard (Fig. 18).
Note: Do not clean more than one
cutter and guard at a time, since
they are all matching sets. If you
accidentally mix up the cutters
and guards, it may take several
weeks before optimal shaving
performance is restored.
4 Remove the cutter from the shaving
guard (Fig. 19).
5 Rinse both parts with water.
6 After cleaning, place the cutter back
into the guard with the cutter legs
pointing downwards (Fig. 20).
7 Put the shaving head back into the
shaving head holder (Fig. 21).
Note: Make sure that the shaving
heads with the projections t
exactly onto the hooks of the
shaving head holder when placing
them (Fig. 23). The shaving heads
supplied with this appliance either
have notches or projections. Both
shaving systems are the same.
8 Push the retaining frame back onto
the shaving head holder until you
hear a click (Fig. 22).
9 Close the shaving head holder
(Fig. 16).
Replacement
Replacing the shaving heads
For maximum shaving performance,
we advise you to replace the shaving
heads every two years. Replace
damaged shaving heads immediately.
Always replace the shaving heads with
original Philips shaving heads (see
‚Ordering accessories‘).
1 Switch o the appliance.
2 Open the shaving unit by opening
both shaving head holders (Fig. 14).
3 To unlock the retaining frames,
gently squeeze both sides of the
retaining frames and ip open the
shaving heads (Fig. 17).
4 Remove the shaving heads from
the shaving head holders (Fig. 18).
Throw away the used shaving
heads immediately to avoid mixing
them with the new shaving heads.
5 Place the new shaving heads in the
shaving head holders.
Note: Make sure that the shaving
heads with the projections t
exactly onto the hooks of the
shaving head holder when placing
them (Fig. 23). The shaving heads
supplied with this appliance either
have notches or projections. Both
shaving systems are the same.
6 Push the retaining frames back onto
the shaving head holder until you
hear a click (Fig. 22).
7 Close the shaving head holders
(Fig. 16).
Prob-
lem
Possible
cause
Solution
The
shaver
does not
work as
well as it
used to.
The
shaving
heads are
damaged
or worn.
Replace
the shaving
heads (see
'Replace-
ment').
The
shaving
heads are
dirty.
Clean the
shaving
heads (see
'Cleaning and
maintenan-
ce').
Long
hairs ob-
struct the
shaving
heads.
Clean the
shaving
heads (see
'Cleaning and
maintenan-
ce').
The
recharge-
able
battery is
low.
Switch o the
shaver and
recharge the
battery (see
'Charging').
The sha-
ver does
not work
when I
switch it
on.
The
recharge-
able
battery is
empty.
Switch o the
shaver and
recharge the
battery (see
'Charging').
The
shaver is
con nect-
ed to
the wall
socket.
This appli-
ance can
only be used
without cord.
Remove the
supply unit
from the wall
socket and
pull the small
plug out of
the appli-
ance.
The
shaving
heads
do not
stay in
place
in the
shaving
unit.
You
did not
x the
retaining
frames
properly.
The retaining
frames are
xed properly
if you hear
a click when
you push it
back onto
the shaving
heads.
The
shaving
heads
with pro-
jec tions
are not
placed
properly.
Make sure
that the sha-
ving heads
with the
projections t
exactly onto
the hooks of
the shaving
head holder
when placing
them (Fig. 23).
简体中文
感谢您的惠顾，欢迎光临飞利
浦！ 为了让您能充分享受飞利
浦提供的支持，请在
www.philips.com/welcome
上注册您的产品。
基本说明（图 1）
1 保护盖
2 剃须刀头支架
3 剃须刀头部件连接器
4 手柄
5 电池充电指示灯
6 开/关按钮
7 小插头插座
8 刀片
9 网罩
10 固定架
11 电源部件
12 小插头
未显示： 清洁刷
重要安全信息
使用本产品及其附件之前，
请仔细阅读本重要信息，
并妥善保管以供日后参考。
随附的附件可能因产品而异。
危险
- 保持电源部件干燥 (图 2)。
- 警告符号注释： 禁止在打开
的水龙头下进行清洗 (图 2)。
警告
- 要给电池充电，请仅使用
产品随附的可拆卸电源部件
(HQ8505)。
- 电源部件中包含一个变压器。
请勿自行更换电源部件的插
头，否则将导致严重后果。
- 本产品也可以由 8 岁或以上
年龄的儿童以及肢体不健全、
感觉或精神上有障碍或缺乏相
关经验和知识的人士使用，但
前提是有人对他们使用本产品
进行监督或指导，以确保他们
安全使用，并且让他们明白相
关的危害。 切勿让儿童玩弄
本产品。 不要让儿童在无人
监督的情况下对本产品进行清
洁和保养。
- 将剃须刀手持部分与电源软
线分开后，才能在水龙头下
清洗手持部分。
- 使用前，请务必检查产品。
请勿使用损坏的产品，否则可
能对人体造成伤害。 请务必
用原装型号更换损坏的部件。
- 切勿拆开本产品更换充电电
池。
警告
- 切勿使用温度高于 60°C
的热水冲洗剃须刀。
- 只能将本产品用于用户手册
中所示的原定用途。
- 出于卫生的目的，本产品只
能供一个人使用。
- 切勿使用压缩气体、钢丝绒、
研磨性清洁剂或腐蚀性液体
（例如汽油或丙酮）来清洁
产品。
- 冲洗剃须刀时，水可能从产
品底部的插口漏出。 这是正
常的，而且没有危险，因为
所有电子元件都封闭在剃须
刀内部的密封电源部件中。
- 请勿在包含电动空气清新器
的墙壁插座上或其周围使用
电源部件，以免电源部件受
到不可修复的损坏。
电磁场 (EMF)
- 本 Philips 产品符合所有有关
暴露于电磁场的适用标准和
法规。
概述
- 符号注释：适合于在洗澡或淋
浴时使用 (图 3)。 允许在盛
水的浴缸、淋浴、洗脸盆或其
他器皿附近使用本器具
。
- 该剃须刀具有防水性能 (图 3)。
适合在沐浴或淋浴时使用，也
可以放在水龙头下清洗。 出于
安全原因，该剃须刀在使用时
不能连接电线。
- 本产品适合在 100 - 240 伏
的电源电压下工作。
- 该电源部件可将 100-240 伏
的电压转换为 24 伏以下的安
全低电压。
充电
注意： 本产品只能在不接电源
的情况下使用。
第一次使用本产品之前，以及
当显示屏指示电池电量快要耗
尽时，请先为本产品充电。
充电约需 1 小时。完全充电的
剃须刀可提供长达 45 分钟的剃
须时间。
使用电源部件充电
1 将小插头插入剃须刀。
2 将电源部件插入电源插座
(图 4)。
3 充电之后，从电源插座上拔
下电源部件，并从产品上拔
下小插头。
4222_002_7319_1_DFU-Leaflet_55x99_6x4_v1.indd 2 05/05/17 11:31
-
1
-
2
他の言語で
- English: Philips S586/12 User manual