dji D6000i ユーザーガイド

v1.0

User Guide

Panduan Pengguna

ユーザーガイド

사용자 가이드



Panduan Pengguna



Hướng dẫn sử dụng

Guía de usuario

Guia do Usuário

Руководство пользователя

Посібник користувача

DJI D6000i

Multifunctional Inverter Generator

1

Compliance Information 138

Appendix 137

EN User Guide 2

Contents

ID Panduan Pengguna13

JP ユーザーガイド 24

KR 사용자 가이드 35

TH  68

VI Hướng dẫn sử dụng 79

RU Руководство пользователя 113

UK Посібник користувача 125

Guía de usuario 90

ES

PT-BR Guia do Usuário 102

MS Panduan Pengguna 57

KM 46



2

EN

Disclaimer

Congratulations on purchasing your new DJITM product. Read this entire document and all safe and lawful

practices DJI provided carefully before use. Failure to read and follow instructions and warnings may result

in serious injury to yourself or others, damage to your DJI product, or damage to other objects in the vicinity.

By using this product, you hereby signify that you have read this document carefully and that you understand

and agree to abide by all terms and conditions of this document and all relevant documents of this product.

You agree to only use this product for proper purposes. You agree that you are solely responsible for your own

conduct while using this product and for any consequences thereof. DJI accepts no liability for damage, injury,

or any legal responsibility incurred directly or indirectly from the use of this product.

DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its aliated companies.

Names of products, brands, etc., appearing in this document are trademarks or registered trademarks of

No part of this product or document shall be reproduced in any form without the prior written consent or

authorization of DJI.

This document and all other collateral documents are subject to change at the sole discretion of DJI. This

content is subject to change without prior notice. For up-to-date product information, visit www.dji.com and go

to the product page for this product.

Warning

1. Please read these instructions carefully before use. Failure to follow the relevant instructions may result in

property damage, personal injury, or death. The warnings and precautions in this manual do not cover all

possible situations and the user must use common sense when using the product and maintain a cautious

attitude.

2. Users must understand the operation of all control components and know how to stop the generator in

emergency.

3. The engine has not been lled with engine oil before leaving the factory. Add SJ 10W-40 (or equivalent)

engine oil before use.

4. To disconnect or reconnect the connector between the DC module and the generator, turn o the generator

rst. DO NOT perform these operations while the generator is running.

5. The generator must be placed on a at and stable surface at least 1.5 m away from buildings or other

equipment. Make sure there is sucient space for ventilation.

6. The generator must be powered o when refueling.

7. DO NOT smoke next to the generator fuel tank and keep the generator away from ames or sparks.

8. Use the generator in an open and well-ventilated outdoor space. In order to prevent re hazards, make sure

that there are no ammable materials near the muer or exhaust port when the generator is in use.

9. Keep the generator clean and tidy. Use a dry towel to clean the generator if any fuel or other ammable

materials are spilled on the generator.

10. To avoid scalding, DO NOT touch the engine or the muer while the generator is running.

11. DO NOT connect the generator to the mains supply or other generators. It must be used alone.

12. Place the generator in a location that cannot be accessed by passers-by or children. Children are not

allowed to operate the generator. Keep children and animals away from the operation area.

13. Pay special attention to the warning and indicative signs and denitions on the generator as shown below:

: DANGER Poisonous Gas, Risk of Suocation : DANGER Risk of Electric Shock

: DANGER Electricity : DANGER Risk of Fire

: CAUTION Risk of Scalding : Fill Engine Oil : Refuel

3

EN

14. Make sure that there is little or no fuel in the fuel tank and that the fuel valve is in the OFF position before

transportation to avoid spilling.

15. Before use, make sure there are no obvious defects such as a broken terminal or worn cable.

16. Properly ground the generator before use. It is recommended to consult with a qualified electrician to

ensure compliance with local electrical codes.

17. The generator exhaust contains poisonous carbon monoxide. DO NOT use the generator indoors or in

other conned space.

18. DO NOT use the generator in the rain or in any other humid environment.

19. Maintain the generator on a regular basis to prolong its life cycle. Refer to Storage and Maintenance section

to see specic maintenance procedures.

In the Box

D6000i Multifunctional Inverter

Generator × 1

Supporting Foot × 2 Caster × 2

Wheel Shaft x 2

Retaining Clip × 2

Bolt (M6×45) × 4

Nut (M6) × 4

Engine Oil Funnel × 1Wrench × 2Handle × 2

Nut (M8) × 2

Bolt (M8×50) × 2 (8×10)

(10×13)

Spark Plug Socket × 1 Screwdriver × 1 High Altitude Carburetor Kit × 1

4

EN

Initial Installation

Removing the Original Supporting Feet

To install the casters and the matching supporting feet, remove the four original supporting feet rst.

1. Nut

2. Original Supporting Foot

3. Bolt

1

2

3

Installing the Supporting Feet

Align the mounting holes on the supporting feet with those on the generator frame. Insert the bolts through the

mounting holes and secure them with nuts.

1. Bolt

2. Supporting Foot

3. Nut

1 2 3

Installing the Casters

Insert the wheel shaft through the wheel and the mounting holes on the generator frame, and secure it

with a clip.

1. Wheel Shaft

2. Caster

3. Clip

1 2 3

Installing the Handles

Align the handle with the mounting holes on the generator frame, insert the bolt throught the mounting holes,

and secure with a nut.

1. Bolt

2. Nut

3. Handle

1

2

3

5

EN

Introduction

The D6000i Multifunctional Inverter Generator (hereinafter referred to as “the generator”) combines the

functionality of a battery charger and generator. It is capable of charging one Intelligent Flight Battery at a

time and also supports 1500 W AC power output*. For compatible batteries, see the Specications section.

The illustrations in this user guide may vary from the actual product.

* The AC power output of the generator may dier depending on your country and region. Refer to the Appendix section for

details.

1. Fuel Tank Cap

2. Fuel Tank

3. Front Board

4. DC Module

5. Status LEDs

6. Charging Cable

7. Casters

8. Operation Panel

9. Muer Shield

10. Spark Arrestor

11. Fuel Valve

12. Spark Plug

13. Handles

14. Engine Oil Dipstick

15. Engine Oil Drain Hose

16. Supporting Feet

17. Primary Air Filter

18. Carburetor

19. Secondary Air Filter

20. Fan Hood

21. Fuel Filter

22. Frame

23. Oil Level Gauge

Overview

Generator

1

2

3

4

5

6

7

8 9 10

11

12

13

14

15

16

17 18 19 20

21

22 23

6

EN

Operation Panel

1. Engine Switch

Used to start or stop the generator. Refer to the Using

the Generator section for more detailed information.

2. AC Outlet*

Used to connect with electric devices. The outlet

meets the IP44 protection rating. Make sure to reinstall

and fasten the outlet shield when not in use.

* The AC power output of the generator may dier depending

on your country and region. Refer to the Appendix section

for details.

3. Ground Terminal

Use a ground cable and connect one end to the

ground terminal and the other end to the ground.

Proper grounding can help to avoid electric shocks in

case of device failure.

1

2

3

ENG.SW.

START

ON

OFF

Status LEDs

1. Charging Channel Status LED

2. DC Module Status LED

3. Generator (excl. DC Module)/AC Module Status LED

4. USB-C Connector Cover

1

2

3

4

Status LED Blinking Pattern Description

Charging Channel

Status LED

Solid yellow The generator is ready to connect to a battery

Blinks green once continuously Charging

Solid green Fully charged

Blinks yellow once continuously Warning for the battery/charging channel

Blinks red once continuously Battery/charging channel error

DC Module Status

LED

Blink yellow four times continuously DC module is not activated

Blinks yellow once continuously Warning for the DC module

Blinks red once continuously DC module error

Generator (excl. DC

Module)/AC Module

Status LED

Blink yellow four times continuously Generator (excl. DC Module)/AC Module is not activated

Blinks yellow once continuously Warning for the generator (excl. DC Module)/AC Module

Blinks red once continuously Generator (excl. DC Module)/AC Module error

Blinks red four times continuously Generator (excl. DC Module) maintenance is required

• When the status LEDs blink indicating a warning or error, connect the USB-C connector of the generator to the USB-A

connector of the remote controller using a USB-C cable. Run the DJI AGRAS™ app on the remote controller and

check the specic warnings or errors on the charging device interface.

• When the status LED blinks prompting for maintenance, connect the USB-C connector of the generator to the USB-A

connector of the remote controller using a USB-C cable. Run the DJI Agras app on the remote controller and check

the specic maintenance information on the charging device interface. When maintenance is nished, press the reset

button on the charging device interface to turn o the status LED blinking for maintenance.

• If any part of the generator is abnormal or damaged, it is recommended to contact a DJI-authorized dealer or DJI

Support to repair or replace the part.

7

EN

Getting Started

Filling Engine Oil

The generator has not been lled with engine oil before leaving the factory. It is necessary to add engine oil

before use.

Place the generator on a flat and stable surface, unscrew the dipstick, fill the engine with oil to the rated

capacity, and screw the dipstick back on. The D6000i Multifunctional Inverter Generator has a rated engine oil

capacity of 0.8 L. Use SJ 10W-40 engine oil (or equivalent).

Refueling

Fuel is highly ammable and explosive. Strictly follow the instructions to use. Before refueling the generator,

power it o and wait until it has completely cooled down.

1. Loosen the fuel tank cap and refuel the fuel tank with the recommended type of fuel to the rated capacity

according the oil level gauge*. The D6000i Multifunctional Inverter Generator has a rated fuel capacity of 20 L.

2. Tighten the fuel tank cap after refuelling. Use a dry towel to wipe up if any fuel is spilled.

* For recommended fuel types for dierent countries and regions, refer to the Appendix section.

• Make sure to turn the fuel valve to the OFF position before refueling or after stopping the generator.

• DO NOT overll fuel. Spilling can lead to a re or explosion.

• Using ethanol fuel may increase the fuel consumption.

Pre-Operation Checking

In order to ensure your safety and preserve the service life of the generator, take some time to check the

conditions of the generator before each operation. Make sure any issues or malfunctions have been resolved

before operation.

Before starting the pre-operation check, make sure the generator is placed on a stable place and the engine

switch is in the OFF position.

Common Check-Up Items

1. Check whether there is any spilled engine oil or fuel around or under the generator.

2. Remove any ammable materials in the surrounding area especially around the muer and the fan hood.

3. Repair or replace any rusted, broken, damaged, deformed, or loosened parts.

4. Check whether the muer shield and the fan hood have been securely installed in place and whether all the

nuts, bolts, and screws have been tightened.

USB-C Cable

USB-C Connector on the Generator

USB-A Connector on the

Remote Controller

8

EN

Important Check-Up Items

1. Checking the fuel level: Fill up the fuel tank before operation to reduce the chance of an operation being

interrupted by a low fuel level.

2. Checking the engine oil level: Working with a low engine oil level will cause damage to the engine. When the

engine oil amount falls below the safety level, the built-in engine oil sensor will stop the engine from working.

Check the engine oil level before each operation to avoid the inconvenience caused by unexpected

ameout.

3. Checking the sponge lter element of the air lter: A dirty sponge lter element decreases the air entering

the carburetor, which reduces the generator performance.

Using the Generator

Activation

The generator must be activated before using for the rst time. Connect the remote controller to the internet

rst. Use a USB-C cable to connect to the USB-C connector of the generator and the USB-A connector of the

remote controller. Run the DJI Agras app on the remote controller and tap on the upper left corner of the

main interface to enter the charging device interface to activate the generator.

• At high altitudes (1000 m or more above sea level), a standard carburetor would produce rich fuel/air mixture which

would decrease engine performance and increase fuel consumption. Rich fuel/air mixture would also contaminate the

spark plug, making it dicult to start the generator.

• To use the generator in places at 1000 m or more above sea level, contact a DJI-authorized dealer or DJI Support to

replace the high altitude carburetor kit. Then use a USB-C cable to connect to the USB-C connector of the generator

and the USB-A connector of the remote controller, and enter DJI Agras app to calibrate the altitude.

• The fuel/air mixture of a high-altitude carburetor kit would be too thin for use at low altitudes (lower than 1000 m),

causing the engine to overheat and sustain severe damage. Therefore, to use the generator at low altitudes again,

contact a DJI-authorized dealer or DJI Support to replace the high-altitude carburetor kit with a low-altitude one. Then

use a USB-C cable to connect to the USB-C connector of the generator and the USB-A connector of the remote

controller, and enter DJI Agras app to calibrate the altitude.

Starting the Generator

1. DO NOT connect to any electric devices before starting the generator.

2. Make sure the engine has been lled with engine oil and the fuel tank with no less than 1L fuel.

3. Turn the fuel valve to the ON position.

4. Connect the charging cable to an Intelligent Flight Battery that is powered o. Press and then press and

hold the power button on the battery to power on the battery. D6000i Multifunctional Inverter Generator can

connect with a T40/T30/T20P Intelligent Flight Battery.

5. Move the engine switch to the Start position and hold for at least 3 seconds and then release. The engine

switch will return to the ON position and the generator will start automatically.

6. The generator starts to charge the battery. Each of the four LEDs of the battery blinks successively during

charging. Remove the battery when the four LEDs turn solid or o and connect another battery to charge.

• The battery must be powered o before connecting it to the generator.

• The generator automatically attempts to start a maximum of three times every time the engine switch is moved to

the Start position with an interval of ve seconds between each start attempt. If the generator fails to start after three

automatic attempts or stops right after starting, connect it to the remote controller to see more information regarding

the malfunction.

• If there are any working electric devices connected to the AC outlet while charging the battery, the charging capacity

for the battery will decrease accordingly and the charging time will be extended.

9

EN

Stopping the Generator

1. Turn o all connected electric devices.

2. Move the engine switch to the OFF position and the generator will stop running.

3. Disconnect all connected electric devices.

4. Turn the fuel valve to the OFF position.

Storage and Maintenance

Storage

Follow the steps below for storage if the generator will not be used for

more than 30 days.

1. Before storage, start the generator and let it run for five to ten

minutes to warm up. Next, stop the generator to drain the engine oil.

2. Take down the engine oil drain hose and rotate the cap

counterclockwise to open. Wait for the oil to drain completely.

To avoid scalding, DO NOT touch hot engine oil.

3. Install and secure the engine oil drain hose back in place. Rotate the

cap clockwise to tighten it.

4. Turn the fuel valve to the OFF position. Remove the fuel drain bolt on

the bottom of the fuel tank, drain the fuel with a funnel, and store the

fuel in a dedicated container to avoid gum formation. Install the fuel

drain bolt back in place after the fuel is completely drained. Clean the

funnel and wipe it with dry cloth before storage.

5. Turn the fuel valve to the ON position. Use a screwdriver to loosen

the carburetor fuel drain bolt, and drain the fuel inside the carburetor

through the pipe connected to the carburetor. Store the fuel in a

dedicated container to avoid gum formation. Tighten the carburetor

fuel drain bolt, and turn the fuel valve to the OFF position.

6. Place the generator in a cool, dry, and clean place.

Transportation

The generator especially its exhaust system can become very hot during running. To avoid scalding or re of

ammable materials, if the generator has been running, wait for at least 15 minutes to let it cool down before

moving it into a transportation vehicle. Make sure the generator is stable during transportation and the fuel valve

is in the OFF position to avoid spilling.

Maintenance

Scan the QR code on the fuel tank to view the tutorial videos or refer to the labels and stickers on the generator

for maintenance instructions.

Check and maintain the generator regularly to keep it in good condition.

Maintenance Safety Notes

• Before maintaining, stop the generator, disconnect all the electric devices and batteries, and let the

generator cool down completely.

Carburetor Fuel Drain Bolt

Fuel Tank Fuel Drain Bolt

10

EN

• Maintain the generator in a clean, dry, and stable place. Make sure the generator cannot move by accident.

• Read the user guide before operation and make sure you have all the tools and the necessary skills.

• Be extremely careful when using the generator near fuel to decrease the possibility of a fire hazard or

explosion. Use non-ammable solvent to clean the parts. DO NOT use fuel for cleaning. Keep the parts with

fuel away from cigarette buttes, sparks, and re.

Maintenance Schedule

Follow the maintenance schedule in table below. The maintenance frequency should be increased if the

generator is running in a dusty or other harsh environment.

Contact a DJI-authorized dealer or DJI Support to perform the maintenance items marked with an asterisk. For

any other maintenance items not covered by this document, contact a DJI-authorized dealer or DJI Support.

Item Every

operation

Every 10

operating

hours

Every 20

operating

hours

Every 50

operating

hours

Every 100

operating

hours

Every 300

operating hours/1

year

Engine Oil Level check √

Replacement* First Use √

Air Filter Sponge

Filter Element

Check/Cleaning √

Replacement* √

Air Filter Paper

Filter Element

Check/Cleaning √

Replacement* √

Spark Arrestor Cleaning √

Spark Plug

(Model: F7RTC)

Check/Cleaning/

Replacement* √

Valve Clearance Adjustment* √

Fuel Passage Cleaning/

Replacement* √

Fuel Pipe Replacement* Every 2 years (or when necessary)

• A maintenance interval of every 300 operating hours/1 year means the user should perform

maintenance based on which scenario occurs rst.

• Fuel passage maintenance requires that after every 300 operating hours, users should contact a DJI-

authorized dealer or DJI Support to check or replace the fuel lter. The replacement interval varies

depending on the quality of the fuel. The interval should be shortened if the fuel quality is poor.

• Engine oil consumption increases if using the generator in high temperature environments. Fill up the

engine oil to the rated level before each use and shorten the interval of replacing the engine oil.

Upper Limit

Lower Limit

Fill Port Dipstick

Checking the Engine Oil Level

1. Stop the generator and place it on a at surface.

2. Unscrew the dipstick and wipe it out with a clean

cloth.

3. Insert the dipstick as shown without screwing it

in. Take the dipstick out and check the oil level.

4. Add the recommended type of engine oil to the

upper limit position if its level is near or below the

lower limit mark. DO NOT add too much engine

oil. Otherwise, the oil may spill.

5. Install the dipstick and tighten it.

11

EN

Paper Filter

Element

Sponge Filter

Element

• Damage to the generator caused by running with a low engine oil level is not covered by warranty.

• Damage to the engine resulting from failure to replace the engine oil by following the maintenance schedule is not

covered by warranty.

• Damage to the engine caused by use of non-recommended engine oil is not covered by warranty.

Replacing Engine Oil

Contact a DJI-authorized dealer or DJI Support to replace the engine oil.

1. Place the generator on a at surface. Start the generator to warm up the

engine for several minutes and then stop the generator.

2. Place a container under the engine oil drain hose.

3. Take down the engine oil drain hose and rotate the cap counterclockwise

to open. Wait for the oil to drain completely.

4. Install and secure the engine oil drain hose back in place. Rotate the cap

clockwise to tighten it.

5. Unscrew the dipstick and use the engine oil funnel to add the SJ 10W-40

engine oil (or equivalent) to the upper limit. Put the dipstick back in and

screw tight.

• Engine oil significantly affects the engine performance and is the main factor that determines its service life. It is

recommended to use oil intended for four-stroke car engines and that meets or exceeds SJ standards according to

the API classication. Normally, the API grade is shown on the package of engine oil bottle. Make sure it says SJ or a

higher grade. The recommended engine oil type is SJ 10W-40.

• To prevent damage to the environment, it is recommended to seal used engine oil in a container and hand it over to a

dedicated recycle center. DO NOT dispose of used engine oil in normal household waste, on the ground, or down a

sewer drain.

Checking and Cleaning Air Filter Element

1. Remove the cover of the primary air lter and take

out the sponge filter element. Clean the sponge

lter element thoroughly in warm soapy water and

let it dry under the sun. Clean the dust in the lter

housing.

2. Immerse the sponge lter element in clean engine

oil and squeeze out the excess engine oil. Put the

sponge lter element back in the lter and reinstall

the cover.

3. Remove the cover of the secondary air lter and take out the paper lter element. If the paper lter element

surface becomes wet with engine oil or fuel or is obviously stained and more than 10% discolored, contact

a DJI-authorized dealer or DJI Support to replace the paper lter element. If it is not necessary to replace the

paper lter element, tap it gently on the ground to shake o any dust and debris. Clean the dust in the lter

housing, and use a carburetor cleaning agent to clean the engine oil in the cover and wipe it dry.

4. Put the dry paper lter element back in the lter and reinstall the cover.

• Replace the sponge lter element if it is damaged during cleaning.

• DO NOT use an air blower or compressed air to clean the paper lter element as it may cause damage to the intake

pores of the element.

• Make sure the sealing ring is still intact in the groove when installing the cover again.

12

EN

Cleaning the Spark Arrestor

1. Use a screwdriver to remove the bolts and the

protective cover. Take out the spark arrestor.

2. Inspect the spark arrestor. Wash it with a

cleaning agent for carburetor and descale it with

a wire brush. Replace the spark arrestor if it is

damaged.

3. Install the cleaned or new spark arrestor and

tighten the bolts.

Checking, Cleaning, and Replacing the Spark Plug

Contact a DJI-authorized dealer or DJI Support to maintain the spark plug.

1. Stop the generator and make sure it has cooled down completely.

2. Unscrew the spark plug with the dedicated spark plug socket and check

the spark plug. Replace the spark plug immediately if the insulator or the

sealing gasket is broken.

3. Remove the carbon deposit or other deposit with a sti wire brush.

4. Adjust the electrode to make sure the gap is within a standard range of 0.6

to 0.8 mm.

5. When installing the spark plug again, thread the spark plug into the

engine by hand for two to three rotations.

6. Continue tightening with the dedicated spark plug socket.

• The recommended torque is 20-24 N·m. A loose spark plug causes the engine to overheat, while tightening the spark

plug too much will cause damage to the threads in the engine.

• The original spark plug model is F7RTC. Installing the wrong type of spark plug will damage the engine.

• To ensure proper operation of the engine, make sure the spark plug gap is correct and there is no deposit.

Specications

Model D6000i

Starting Method Start the generator via the engine switch

Operating Temperature -5° to 40° C

Max Operating Altitude 1000 m (The output power will drop if the generator is working at an altitude higher than

1000 m. Contact a DJI-authorized dealer or DJI Support to replace the carburetor kit.)

Rated Rotation Speed of Engine 3600 RPM

Fuel Type Refer to the Appendix section.

Engine Oil Type SJ 10W-40

Fuel Tank Capacity 20 L

Engine Oil Capacity 0.8 L

Rated Output DC: 59.92 V

AC: Refer to the Appendix section.

Rated AC Power Refer to the Appendix section.

Total Rated Power 4500 W

Maximum Engine Power 6300 W

Compatible Batteries T40/T30/T20P Intelligent Flight Battery

Dimensions 765×675×630 mm

13

ID

Penaan

Selamat atas pembelian produk DJITM Anda yang baru. Baca dengan saksama seluruh dokumen ini serta

seluruh praktik yang aman dan sah yang disediakan DJI sebelum digunakan. Kegagalan membaca serta

mematuhi instruksi dan peringatan dapat mengakibatkan cedera serius terhadap diri Anda dan orang lain,

kerusakan pada produk DJI Anda, serta kerusakan terhadap objek di sekitar Anda. Dengan menggunakan

produk ini, Anda dengan ini menyatakan bahwa Anda telah membaca dokumen ini secara saksama serta

bahwa Anda memahami dan setuju untuk menaati semua syarat serta ketentuan dokumen ini dan semua

dokumen yang terkait dengan produk ini. Anda setuju untuk hanya menggunakan produk ini untuk tujuan yang

tepat. Anda setuju bahwa Anda bertanggung jawab penuh atas perilaku Anda selama menggunakan produk ini,

dan atas semua konsekuensinya. DJI tidak memiliki tanggung jawab apa pun atas kerusakan, atau tanggung

jawab hukum yang timbul secara langsung maupun tidak langsung dari penggunaan produk ini.

DJI adalah merek dagang dari SZ DJI TECHNOLOGY CO., LTD. (disingkat sebagai “DJI”) dan perusahaan

aliasinya. Nama produk, merek, dll., yang muncul dalam dokumen ini merupakan merek dagang atau merek

dagang terdaftar dari masing-masing perusahaan pemiliknya. Produk dan dokumen ini merupakan hak cipta

dari DJI dengan semua hak dilindungi oleh undang-undang. Tidak ada bagian dari produk atau dokumen ini

yang boleh diperbanyak dalam bentuk apa pun tanpa persetujuan tertulis sebelumnya atau izin dari DJI.

Dokumen ini dan seluruh dokumen pendukung lainnya dapat berubah dari waktu ke waktu atas pertimbangan

penuh DJI. Konten ini dapat berubah sewaktu-waktu tanpa pemberitahuan sebelumnya. Untuk informasi

produk terkini, kunjungi www.dji.com dan buka produk untuk produk ini.

Peringatan

1. Bacalah petunjuk ini dengan saksama sebelum menggunakan. Kegagalan untuk mengikuti instruksi yang

tepat dapat mengakibatkan kerusakan properti, cedera pribadi, atau kematian. Peringatan dan tindakan

pencegahan dalam panduan ini tidak mencakup semua situasi yang mungkin terjadi dan pengguna harus

menggunakan akal sehat saat menggunakan produk ini dan mempertahankan sikap hati-hati.

2. Pengguna harus memahami pengoperasian semua komponen kontrol dan mengetahui cara menghentikan

generator dalam keadaan darurat.

3. Mesin belum diisi oli mesin sebelum meninggalkan pabrik. Tambahkan oli mesin SJ 10W-40 (atau yang

setara) sebelum digunakan.

4. Untuk memutuskan atau menghubungkan kembali konektor antara modul DC dan generator, matikan

generator terlebih dahulu. JANGAN lakukan operasi ini saat generator sedang bekerja.

5. Generator harus diletakkan di atas permukaan yang datar dan stabil, sekurang-kurangnya 1,5 m dari

bangunan atau peralatan lainnya. Pastikan ada ruang yang cukup untuk ventilasi.

6. Generator harus dimatikan saat mengisi bahan bakar.

7. JANGAN merokok di samping tangki bahan bakar generator dan jauhkan generator dari nyala api atau

bunga api.

8. Gunakan generator di ruang terbuka yang berventilasi baik di luar ruangan. Untuk mencegah bahaya

kebakaran, pastikan tidak ada bahan mudah terbakar di dekat knalpot atau lubang pembuangan saat

generator digunakan.

9. Jaga generator tetap bersih dan rapi. Gunakan handuk kering untuk membersihkan generator jika ada

bahan bakar atau bahan mudah terbakar yang tumpah ke generator.

10. Untuk menghindari lecet, JANGAN menyentuh mesin atau muer saat generator bekerja.

11. JANGAN menghubungkan generator ke pasokan listrik atau generator lainnya. Ini harus digunakan sendiri.

12. Tempatkan generator di lokasi yang tidak dapat diakses oleh pejalan kaki atau anak-anak. Anak-anak tidak

diperbolehkan mengoperasikan generator. Jauhkan anak-anak dan binatang dari area operasi.

13. Berikan perhatian khusus pada peringatan dan tanda serta denisi indikatif pada generator seperti yang

ditunjukkan di bawah ini:

: BAHAYA Gas Beracun, Risiko Tercekik : BAHAYA Risiko Sengatan Listrik

: BAHAYA Kelistrikan : BAHAYA Risiko Kebakaran

: PERHATIAN Risiko Melepuh : Isi Oli Mesin : Pengisian Ulang Bahan Bakar

14

ID

14. Pastikan bahwa ada sedikit atau tidak ada bahan bakar dalam tangki bahan bakar dan bahwa katup bahan

bakar berada dalam posisi MATI sebelum pengangkutan untuk menghindari tumpahan.

15. Sebelum digunakan, pastikan tidak ada kerusakan nyata seperti terminal yang rusak atau kabel yang aus.

16. Tajamkan generator dengan benar sebelum digunakan. Disarankan untuk berkonsultasi dengan teknisi

listrik yang berkualikasi untuk memastikan kepatuhan dengan peraturan listrik setempat.

17. Knalpot generator mengandung karbon monoksida beracun. JANGAN menggunakan generator di dalam

ruangan atau ruang tertutup lainnya.

18. JANGAN gunakan generator dalam hujan atau lingkungan lembab lainnya.

19. Pertahankan generator secara teratur untuk memperpanjang siklus hidupnya. Lihat bagian Penyimpanan

dan Perawatan untuk melihat prosedur pemeliharaan spesik.

Dalam kotak

D6000i Generator Inverter

Multifungsi × 1

Penyangga Kaki × 2 Caster × 2

Batang Roda x 2

Klip Penahan × 2

Baut (M6×45) × 4

Mur (M6) × 4

Corong Oli Mesin × 1Kunci × 2Pegangan × 2

Mur (M8) × 2

Baut (M8×50) × 2 (8×10)

(10×13)

Soket Busi × 1 Obeng × 1 Kit Karburator Ketinggian

Tinggi × 1

15

ID

Pemasangan Awal

Melepas Penyangga Kaki Asli

Untuk memasang kastor dan penyangga kaki yang sesuai, pertama lepaskan keempat penyangga kaki asli.

1. Mur

2. Pennyangga Kaki Asli

3. Baut

1

2

3

Memasang Penyangga Kaki

Sejajarkan lubang pemasangan pada penyangga kaki dengan lubang pada rangka generator. Masukkan baut

melalui lubang pemasangan dan kencangkan dengan mur.

1. Baut

2. Penyangga Kaki

3. Mur

1 2 3

Memasang Castor

Masukkan poros roda melalui roda dan lubang pemasangan pada rangka generator, lalu kencangkan dengan

klip.

1. Batang Roda

2. Caster

3. Klip

1 2 3

Memasang Gagang

Sejajarkan pegangan dengan lubang dudukan pada rangka generator, masukkan baut melalui lubang

pemasangan, dan kencangkan dengan mur.

1. Baut

2. Mur

3. Pegangan

1

2

3

16

ID

Pengantar

Multifunctional Inverter Generator D6000i (selanjutnya disebut sebagai “generator”) menggabungkan

fungsionalitas pengisi daya baterai dan generator. Perangkat ini mampu mengisi daya satu Baterai Penerbangan

Cerdas pada satu waktu dan juga mendukung output daya AC 1500 W*. Untuk baterai yang kompatibel, lihat

bagian Spesikasi.

Ilustrasi dalam panduan pengguna ini dapat bervariasi dari produk sebenarnya.

* Output daya AC dari generator mungkin berbeda, tergantung pada negara dan wilayah Anda. Lihat bagian Lampiran untuk

perinciannya.

1. Tutup Tangki Bahan Bakar

2. Tangki Bahan Bakar

3. Meja Depan

4. Modul DC

5. LED Status

6. Kabel Pengisian Daya

7. Caster

8. Panel Operasi

9. Perisai Knalpot

10. Penahan Bunga Api

11. Katup Bahan Bakar

12. Busi

13. Pegangan

14. Batang Celup Oli Mesin

15. Selang Penguras Oli

Mesin

16. Penyangga Kaki

17. Filter Udara Primer

18. Karburator

19. Filter Udara Sekunder

20. Tudung Kipas

21. Filter Bahan Bakar

22. Bingkai

23. Pengukur Level Oli

Ikhtisar

Generator

1

2

3

4

5

6

7

8 9 10

11

12

13

14

15

16

17 18 19 20

21

22 23

17

ID

Panel Operasi

1. Saklar Mesin

Digunakan untuk memulai atau menghentikan

generator. Lihat bagian Menggunakan Generator untuk

informasi yang lebih terperinci.

2. Stopkontak AC*

Digunakan untuk terhubung dengan perangkat listrik.

Stop kontak memenuhi peringkat perlindungan

IP44. Pastikan untuk memasang kembali dan

mengencangkan pelindung outlet saat tidak digunakan.

* Output daya AC dari generator mungkin berbeda, tergantung

pada negara dan wilayah Anda. Lihat bagian Lampiran untuk

perinciannya.

3. Terminal Darat

Gunakan kabel arde dan hubungkan salah satu ujung

ke terminal arde dan ujung lainnya ke arde. Pentanahan

yang tepat dapat membantu menghindari sengatan

listrik jika terjadi kegagalan perangkat.

1

2

3

ENG.SW.

MULAI

HIDUP

MATI

LED Status

1. LED Status Saluran Pengisian Daya

2. LED Status Modul DC

3. LED Status Modul AC/Generator (tidak termasuk

Modul DC)

4. Penutup Konektor USB-C

1

2

3

4

LED Status Pola Berkedip Deskripsi

LED Status

Saluran

Pengisian Daya

Menyala kuning tanpa kedip Generator siap untuk terhubung ke baterai

Berkedip hijau satu kali secara terus menerus Mengisi Daya

Menyala hijau tanpa kedip Terisi penuh

Berkedip kuning sekali terus menerus Peringatan untuk saluran pengisian daya/baterai

Berkedip merah satu kali terus menerus Kesalahan saluran pengisian daya/baterai

LED Status

Modul DC

Berkedip kuning empat kali secara terus-menerus Modul DC tidak diaktifkan

Berkedip kuning sekali terus menerus Peringatan untuk modul DC

Berkedip merah satu kali terus menerus Kesalahan modul DC

LED Status

Modul AC/

Generator (tidak

termasuk Modul

DC)

Berkedip kuning empat kali secara

terus-menerus

Generator (tidak termasuk Modul DC)/Modul AC tidak

diaktifkan

Berkedip kuning sekali terus menerus Peringatan untuk generator (tidak termasuk Modul DC)/

Modul AC

Berkedip merah satu kali terus menerus Kesalahan Modul AC/Generator (tidak termasuk Modul DC)

Berkedip merah empat kali secara

terus-menerus

Pemeliharaan Generator (tidak termasuk Modul DC)

diperlukan

• Ketika LED status berkedip yang menunjukkan peringatan atau kesalahan, sambungkan konektor USB-C generator ke

konektor USB-A pengendali jarak jauh menggunakan kabel USB-C. Jalankan aplikasi DJI AGRAS™ pada pengendali

jarak jauh dan periksa peringatan khusus atau kesalahan pada antarmuka perangkat pengisian daya.

• Ketika LED status berkedip dan memerintahkan pemeliharaan, sambungkan konektor USB-C generator ke konektor

USB-A pengendali jarak jauh menggunakan kabel USB-C. Jalankan aplikasi DJI Agras pada pengendali jarak jauh dan

periksa informasi pemeliharaan spesik pada antarmuka perangkat pengisian daya. Ketika perawatan selesai, tekan

tombol reset pada antarmuka perangkat pengisian daya untuk mematikan LED status yang berkedip untuk pemeliharaan.

• Apabila terdapat bagian generator yang abnormal atau rusak, disarankan untuk menghubungi dealer resmi DJI atau

Dukungan DJI untuk memperbaiki atau mengganti bagian tersebut.

18

ID

Panduan Memulai

Pengisian Oli Mesin

Generator belum diisi oli mesin sebelum meninggalkan pabrik. Perlu menambahkan oli mesin sebelum

digunakan.

Tempatkan generator pada permukaan yang datar dan stabil, lepaskan batang celup, isi mesin dengan oli

ke kapasitas terukur, dan pasang kembali batang celup. D6000i Multifunctional Inverter Generator memiliki

kapasitas oli mesin terukur 0,8 L. Gunakan oli mesin SJ 10W-40 (atau setara).

Pengisian Ulang Bahan Bakar

Bahan bakar mudah terbakar dan meledak. Ikuti dengan ketat petunjuk penggunaan. Sebelum mengisi bahan

bakar generator, matikan dan tunggu hingga benar-benar dingin.

1. Longgarkan tutup tangki bahan bakar dan isi bahan bakar dengan jenis bahan bakar yang disarankan ke

kapasitas terukur sesuai dengan pengukur ketinggian oli*. Generator Inverter Multifungsi D6000i memiliki

kapasitas bahan bakar terukur 20 L.

2. Kencangkan tutup tangki bahan bakar setelah pengisian ulang bahan bakar. Gunakan handuk kering untuk

menyeka bahan bakar yang tumpah.

* Untuk jenis bahan bakar yang direkomendasikan untuk negara dan wilayah yang berbeda, lihat bagian Lampiran.

• Pastikan untuk memutar katup bahan bakar ke posisi MATI sebelum mengisi bahan bakar atau setelah menghentikan

generator.

• JANGAN mengisi bahan bakar secara berlebihan. Tumpahan dapat menyebabkan kebakaran atau ledakan.

• Menggunakan bahan bakar etanol dapat meningkatkan konsumsi bahan bakar.

Pemeriksaan Pra-Operasi

Untuk memastikan keselamatan Anda dan menjaga umur pakai generator, luangkan waktu untuk memeriksa

kondisi generator sebelum setiap operasi. Pastikan semua masalah atau kegagalan fungsi telah diselesaikan

sebelum operasi.

Sebelum memulai pemeriksaan pra-operasi, pastikan generator ditempatkan pada tempat yang stabil dan

sakelar mesin dalam posisi MATI.

Poin-poin Check-Up Umum

1. Periksa apakah ada tumpahan oli mesin atau bahan bakar di sekitar atau di bawah generator.

2. Hilangkan bahan mudah terbakar di area sekitar terutama di sekitar knalpot dan lemari kipas.

3. Perbaiki atau ganti komponen yang berkarat, rusak, berubah bentuk, atau longgar.

4. Periksa apakah pelindung muer dan hood kipas telah dipasang dengan aman dan apakah semua mur,

baut, dan sekrup telah dikencangkan.

Kabel USB-C

Konektor USB-C pada Generator

Konektor USB-A pada

Pengendali Jarak Jauh

19

ID

Poin-poin Check-Up Penting

1. Memeriksa ketinggian bahan bakar: Isi tangki bahan bakar sebelum operasi untuk mengurangi

kemungkinan operasi terganggu oleh ketinggian bahan bakar yang rendah.

2. Memeriksa ketinggian oli mesin: Bekerja dengan oli mesin yang rendah akan menyebabkan kerusakan

pada mesin. Ketika jumlah oli mesin turun di bawah tingkat keamanan, sensor oli mesin bawaan akan

menghentikan kerja mesin. Periksa ketinggian oli mesin sebelum setiap operasi untuk menghindari

ketidaknyamanan yang disebabkan oleh nyala api mati yang tidak terduga.

3. Memeriksa elemen filter spons pada filter udara: Elemen filter spons kotor menurunkan udara yang

memasuki karburator, yang mengurangi kinerja generator.

Menggunakan Generator

Aktivasi

Generator harus diaktifkan sebelum digunakan untuk pertama kali. Hubungkan pengendali jarak jauh ke internet

terlebih dahulu. Gunakan kabel USB-C untuk terhubung ke konektor USB-C generator dan konektor USB-A

pengendali jarak jauh. Jalankan aplikasi DJI Agras pada pengendali jarak jauh dan ketuk di sudut kiri atas

antarmuka utama untuk memasuki antarmuka perangkat pengisian daya untuk mengaktifkan generator.

• Pada ketinggian yang tinggi (1000 m atau lebih di atas permukaan laut), karburator standar akan menghasilkan

campuran bahan bakar/udara yang kaya yang akan mengurangi kinerja mesin dan meningkatkan konsumsi bahan

bakar. Campuran bahan bakar/udara yang kaya juga akan mencemari busi, sehingga sulit untuk menyalakan

generator.

• Untuk menggunakan generator di tempat pada kecepatan 1000 m atau lebih di atas permukaan laut, hubungi dealer

resmi DJI atau Dukungan DJI untuk mengganti kit karburator ketinggian tinggi. Lalu gunakan kabel USB-C untuk

terhubung ke konektor USB-C generator dan konektor USB-A pengendali jarak jauh, dan masuk ke aplikasi DJI Agras

untuk mengkalibrasi ketinggian.

• Campuran bahan bakar/udara pada kit karburator dengan ketinggian tinggi akan menjadi terlalu tipis untuk digunakan

pada ketinggian rendah (lebih rendah dari 1000 m), menyebabkan mesin terlalu panas dan menahan kerusakan

parah. Oleh karena itu, untuk menggunakan generator kembali pada ketinggian rendah, hubungi dealer resmi DJI atau

Dukungan DJI untuk mengganti kit karburator dengan kecepatan tinggi dengan karburator ketinggian rendah. Lalu

gunakan kabel USB-C untuk terhubung ke konektor USB-C generator dan konektor USB-A pengendali jarak jauh, dan

masuk ke aplikasi DJI Agras untuk mengkalibrasi ketinggian.

Memulai Generator

1. JANGAN sambungkan ke perangkat listrik sebelum menyalakan generator.

2. Pastikan mesin telah diisi dengan oli mesin dan tangki bahan bakar dengan bahan bakar tidak kurang dari 1L.

3. Putar katup bahan bakar ke posisi HIDUP.

4. Sambungkan kabel pengisian daya ke Baterai Penerbangan Cerdas yang dimatikan. Tekan sekali, lalu

tekan lagi dan tahan tombol daya pada baterai untuk menyalakan baterai. D6000i Multifunctional Inverter

Generator dapat terhubung dengan Baterai Penerbangan Cerdas T40/T30/T20P.

5. Pindahkan sakelar mesin ke posisi Mulai dan tahan selama setidaknya 3 detik lalu lepaskan. Sakelar mesin

akan kembali ke posisi ON dan generator akan menyala secara otomatis.

6. Generator mulai mengisi daya baterai. Masing-masing dari keempat LED baterai berkedip secara berurutan

selama pengisian daya. Lepaskan baterai saat keempat LED terpasang atau mati, lalu hubungkan baterai

lain untuk mengisi daya.

• Baterai harus dimatikan sebelum menghubungkannya ke generator.

• Generator secara otomatis mencoba untuk menyalakan maksimum tiga kali setiap kali saklar mesin dipindahkan ke

posisi Mulai dengan interval lima detik di antara setiap upaya start. Jika generator gagal menyala setelah tiga kali

percobaan otomatis atau berhenti setelah dinyalakan, hubungkan ke pengendali jarak jauh untuk melihat informasi

lebih lanjut mengenai malafungsi tersebut.

• Jika ada perangkat listrik yang berfungsi yang terhubung ke stopkontak AC saat mengisi daya baterai, kapasitas

pengisian baterai akan berkurang dan waktu pengisian akan diperpanjang.

ページを読み込んでいます...

dji D6000i ユーザーガイド

その他の書類