Dell PowerEdge Rack Enclosure 4020S クイックスタートガイド

Dell™ PowerEdge™ 4210

Installation Guide

Guide d'installation

Installationshandbuch

インストールガイド

Guía de instalación

Dell™ PowerEdge™ 4210

Installation Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

October 2007 P/N FX668 Rev. A00

Contents 3

Contents

Safety Instructions. . . . . . . . . . . . . . . . . . . . . 5

SAFETY: Rack Mounting of Systems

. . . . . . . . . 5

Installation Instructions

. . . . . . . . . . . . . . . . . . 6

Rack Requirements

. . . . . . . . . . . . . . . . . . 6

Rack Installation

. . . . . . . . . . . . . . . . . . . . . . 6

Before You Begin

. . . . . . . . . . . . . . . . . . . 7

Installation Tasks

. . . . . . . . . . . . . . . . . . . 8

Recommended Tools and Supplies

. . . . . . . . . . 8

Removing and Replacing the Rack Doors

. . . . . . 8

Removing the Front Door

. . . . . . . . . . . . . . . 8

Replacing the Front Door

. . . . . . . . . . . . . . 10

Opening and Removing the Back Doors

. . . . . . 10

Replacing the Back Doors

. . . . . . . . . . . . . 13

Removing the Side Panels

. . . . . . . . . . . . . 13

Replacing the Side Panels

. . . . . . . . . . . . . 14

Reversing the Front Door (optional)

. . . . . . . . 14

Securing the Rack Leveling Feet

. . . . . . . . . . 19

Installing the Rack Stabilizer Feet

. . . . . . . . . 21

Routing Cables

. . . . . . . . . . . . . . . . . . . 24

Removing the Door Panels From the

Optional Door Kit

. . . . . . . . . . . . . . . . . . 26

Coupling Two Racks

. . . . . . . . . . . . . . . . . . . 26

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4 Contents

Dell™ PowerEdge™ 4210 Installation Guide 5

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to

help protect your system and working environment from potential damage.

For complete safety and regulatory information, see the Product Information

Guide that shipped with your system. Warranty information might be

included in this document or as a separate document.

SAFETY: Rack Mounting of Systems

Observe the following precautions for rack stability and safety. Also refer to

the rack installation documentation accompanying the system and the rack

for specific caution statements and procedures.

Systems are considered to be components in a rack. Thus, "component" refers

to any system as well as to various peripherals or supporting hardware.

CAUTION: Before installing systems in a rack, install front and side stabilizers on

stand-alone racks or the front stabilizer on racks joined to other racks. Failure to

install stabilizers accordingly before installing systems in a rack could cause the

rack to tip over, potentially resulting in bodily injury under certain circumstances.

Therefore, always install the stabilizer(s) before installing components in the rack.

After installing system/components in a rack, never pull more than one component

out of the rack on its slide assemblies at one time. The weight of more than one

extended component could cause the rack to tip over and may result in serious

injury.

NOTE: Your system is safety-certified as a free-standing unit and as a component

for use in a Dell rack cabinet using the customer rack kit. The installation of your

system and rack kit in any other rack cabinet has not been approved by any safety

agencies. It is your responsibility to ensure that the final combination of system and

rack complies with all applicable safety standards and local electric code

requirements. Dell disclaims all liability and warranties in connection with such

combinations.

• System rack kits are intended to be installed in a rack by trained service

technicians. If you install the kit in any other rack, be sure that the rack

meets the specifications of a Dell rack.

6 Dell™ PowerEdge™ 4210 Installation Guide

CAUTION: Do not move racks by yourself. Due to the height and weight of the

rack, a minimum of two people should accomplish this task.

• Before working on the rack, make sure that the stabilizers are secured to

the rack, extended to the floor, and that the full weight of the rack rests on

the floor. Install front and side stabilizers on a single rack or front

stabilizers for joined multiple racks before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the

rack first.

• Make sure that the rack is level and stable before extending a component

from the rack.

• Use caution when pressing the component rail release latches and sliding a

component into or out of a rack; the slide rails can pinch your fingers.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any component when servicing other

components in a rack.

Installation Instructions

This installation guide provides instructions for trained service technicians

installing a 42-unit (U) rack. Information includes assembling the rack,

coupling two 42-U racks, and routing cables through the rack. The 42-U rack

can be installed using the recommended tools.

Rack Requirements

NOTICE: The 42-U rack meets the specifications of American National

Standards Institute (ANSI)/Electronic Industries Association (EIA) standard

ANSI/EIA-310-D-92, Consumer Electronics Association (CEA) Standard CEA-310-E,

International Electrotechnical Commission (IEC) 297, and Deutsche Industrie Norm

(DIN) 41494.

Rack Installation

Before attempting this installation, you should read through this entire

procedure carefully.

Dell™ PowerEdge™ 4210 Installation Guide 7

Before You Begin

CAUTION: Before you begin installing your rack, carefully read "Important Safety

Information," as well as the safety instructions found in your system’s System

Information Guide for additional information.

CAUTION: When installing multiple systems in a rack, complete all of the

procedures for the current system before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on the casters.

The cabinet has no brakes. Use extreme caution while moving the rack cabinet.

Retract the leveling feet when relocating the rack cabinet. Avoid long or steep

inclines or ramps where loss of cabinet control may occur. Extend the leveling

feet for support and to prevent the cabinet from rolling.

CAUTION: Do not attempt to move your rack with components installed. If you

move a fully loaded rack on a slightly uneven floor surface, the rack may become

unstable and tip over.

Important Safety Information

Observe the safety precautions in the following subsections when installing

your system in the rack.

CAUTION: You must strictly follow the procedures in this document to protect

yourself as well as others who may be involved. Your system may be very large

and heavy, and proper preparation and planning are important to prevent injury to

yourself and to others. This becomes increasingly important when systems are

installed high up in the rack.

Rack Stabilizer Feet

CAUTION: Installing systems in a rack without the front and side stabilizer feet

installed could cause the rack to tip over, potentially resulting in bodily injury

under certain circumstances. Therefore, always install the stabilizer feet before

installing components in the rack.

CAUTION: After installing systems in a rack, never pull more than one system out

of the rack on its slide assemblies at one time. The weight of more than one

extended system could cause the rack to tip over and cause injury.

The stabilizer feet help prevent the rack from tipping over when a system or

other component is pulled out of the rack with the slide assemblies fully

extended.

8 Dell™ PowerEdge™ 4210 Installation Guide

Installation Tasks

Installing a rack cabinet involves performing the following tasks:

1

Removing and replacing the rack doors

2

Removing and replacing the side panels

3

Reversing the front door and badge (optional)

4

Securing the leveling feet

5

Installing the stabilizer feet

6

Routing cables through the rack

7

Coupling two racks (optional)

8

Removing high-density rear door panels

Recommended Tools and Supplies

You may need the following tools and supplies to install the rack:

• #2 Phillips screwdriver

• Flat head screwdriver

• 12-mm wrench

• Needle-nose pliers

• 4-mm Allen wrench (if you want to reverse the direction that the front

door opens)

• 5-mm Allen wrench (included in kit)

• Keys to the rack doors and side panels

Removing and Replacing the Rack Doors

CAUTION: Because of the size and weight of the rack cabinet doors, never

attempt to remove or install them by yourself.

CAUTION: Store the doors where they will not injure someone if the doors

accidently fall over.

Removing the Front Door

1

Press the door-latch button to release the door handle, then open the front

door all the way (see Figure 1-1).

Dell™ PowerEdge™ 4210 Installation Guide 9

2

While holding the door, pull the top hinge pin upward so that it clears the

door’s hinge-pin housing (see Figure 1-1).

The hinge pin’s retention clip prevents the hinge from being pulled out of

the hinge body.

Figure 1-1. Removing the Front Door

3

While holding the hinge pin out of the door’s hinge-pin housing, pull the

door slightly away from the rack so that the door clears the hinge body.

4

Release the hinge pin.

1 door-latch button 2 hinge pin

3 hinge body 4 hinge-pin housing

4

2

3

1

10 Dell™ PowerEdge™ 4210 Installation Guide

5

Lift the door upward so that the door clears the bottom hinge post.

CAUTION: Due to the size and weight of the door, it is recommended that you lay

the removed door flat.

6

Lay the panel in a safe location with the panel’s outer surface facing

upward.

Laying the door flat with the outer surface facing upward will help prevent

damage to the door’s cosmetic coating.

Replacing the Front Door

To replace the front door, perform the steps for removal in reverse.

Opening and Removing the Back Doors

CAUTION: Because of the size and weight of the rack cabinet doors, never

attempt to remove or install them by yourself.

1

Open the back doors.

a

Press the door-latch button to release the right door handle (see

Figure 1-2).

b

Open the right door.

c

Compress the left door’s pinch latch to release the left door (see

Figure 1-2).

d

Open the left door.

Dell™ PowerEdge™ 4210 Installation Guide 11

Figure 1-2. Opening the Left Back Door

2

Remove the right door.

a

While supporting the door, pull the pin for the top hinge out of the

door’s hinge-pin housing (see Figure 1-3).

You will hear a click as you pull the pin out of the door’s hinge-pin

housing. The hinge pins are designed to prevent them from being

pulled out of the hinge body.

b

Repeat step a for the bottom hinge.

c

Pull the door away from the rack.

1 pinch latch 2 door-latch button

1

2

12 Dell™ PowerEdge™ 4210 Installation Guide

Figure 1-3. Removing the Back Doors

CAUTION: Due to the size and weight of the door, it is recommended that you lay

the removed door flat with its outer surface facing upward.

d

Lay the door in a safe location with the door’s outer surface facing

upward.

Laying the door flat with the outer surface facing upward helps

prevent damage to its cosmetic coating.

e

Repeat steps a through d for the left door.

1 hinge pin 2 hinge body

3 hinge-pin housing

1

2

3

Dell™ PowerEdge™ 4210 Installation Guide 13

Replacing the Back Doors

To replace the back doors, perform the steps for removal in reverse.

Removing the Side Panels

CAUTION: Because of the size and weight of the rack cabinet side panels, never

attempt to remove or install them by yourself.

NOTE: You must remove the side panels in order to install the side stabilizer feet.

Also, although removing the side panels is not mandatory for installing systems in a

rack, having the sides open makes it easier to install slide assemblies and support

rails and to reverse the direction that the front door opens.

1

Unlock the locks near the left and right edges of the panel (see Figure 1-4).

Figure 1-4. Removing a Side Panel

1 side panel (2) 2 locks (2)

3 handles (2)

1

2

3

14 Dell™ PowerEdge™ 4210 Installation Guide

2

Allow the side panel to swing outward slightly from the bottom.

3

Grasp the panel firmly using the handles.

4

Lift the panel upward until it clears the top of the rack (see Figure 1-4).

5

Pull the side panel away from the rack.

CAUTION: Because of the size and weight of the rack cabinet side panels, never

attempt to remove or install them by yourself.

6

Place the panel in a safe location with the panel’s outer surface facing

upward.

Placing the panel with the outer surface facing upward helps prevent

damage to its cosmetic coating.

7

Repeat step 1 through step 6 for the other side panel.

Replacing the Side Panels

CAUTION: Because of the size and weight of the rack cabinet side panels, never

attempt to remove or install them by yourself.

To replace the side panels, perform the removal steps in reverse.

Reversing the Front Door (optional)

NOTE: Use a 4-mm Allen wrench to remove the front-door hinge bodies from the

rack and reinstall them on the side opposite their original positions. You might need

a stepladder in order to access the Allen bolt that secures the top hinge body to the

rack.

To reverse the direction that the front door opens, complete the following

steps:

1

Remove the front door. For instructions, see "Removing the Front Door."

2

Remove the side panels. For instructions, see "Removing the Side Panels."

3

Reverse the top hinge body.

a

Pull the hinge pin upward slightly so that you can access the retention

clip (see Figure 1-5).

b

Using the needle-nose pliers, remove the retention clip, and slide the

hinge pin out of the hinge body.

Dell™ PowerEdge™ 4210 Installation Guide 15

Figure 1-5. Removing the Front-Door Hinges

c

Remove the hinge spring from the hinge body.

d

Place the hinge pin, retention clip, and spring in a safe location.

e

Using the 4-mm Allen wrench, remove the Allen bolt that secures the

hinge body to the rack, and place the bolt with the hinge pin,

retention clip, and spring.

1 hinge post 2 retention clip

3 spring 4 hinge pin

5 top hinge body 6 bottom hinge body

4

3

2

5

6

1

16 Dell™ PowerEdge™ 4210 Installation Guide

f

Rotate the hinge body 180 degrees so that the hinge-pin holes are now

on the right side of the hinge body (see Figure 1-6).

Figure 1-6. Reversing the Top and Bottom Hinges

1 hinge pin 2 top hinge body

3 spring 4 retention clip

5 hinge post 6 bottom hinge body

7 front of rack

2

3

4

1

5

6

7

Dell™ PowerEdge™ 4210 Installation Guide 17

g

Locate the top bolt hole in the right side of the rack, and fasten the

hinge body to the right side of the rack with the Allen bolt.

h

Insert the spring between the top and bottom hinge-pin holes in the

hinge body.

i

Slide the hinge pin into the hinge body.

j

Insert the retention clip through the hinge so that the retention clip is

below the spring.

4

Reverse the bottom hinge body.

a

Remove the Allen bolt that secures the hinge body to the rack, and

place the bolt in a safe location.

b

Rotate the hinge body 180 degrees so that the hinge posts are now on

the right side of the hinge body (see Figure 1-6).

c

Locate the bottom bolt hole in the right side of the rack, and use the

Allen bolt to fasten the hinge body to the right side of the rack.

5

Rotate the front door 180 degrees so that its hinge-pin housings are on the

right side (see Figure 1-7).

18 Dell™ PowerEdge™ 4210 Installation Guide

Figure 1-7. Rotate Front Door

6

Rehang the front door by reversing the steps in "Removing the Front

Door."

7

Reverse the lock catch.

a

Use the #2 Phillips screwdriver to remove the two #2 Phillips screws

that hold the lock catch to the middle horizontal frame member.

b

Remove the lock catch and rotate it 180 degrees.

c

Reinstall the lock catch on the new horizontal frame member by

aligning the holes of the catch with the holes of the frame member

and then reinserting the two #2 Phillips screws.

ページを読み込んでいます...

Dell PowerEdge Rack Enclosure 4020S クイックスタートガイド

関連論文

その他の書類