E188
前言
尊敬的用户：
感谢您选购得胜E188（新版）有线扩音器，为了您能够更好的了解使用本产品，
建议您在使用前仔细阅读本说明书。
若存在有疑问或者您有宝贵的建议，可通过拨打得胜官方
服务热线400 6828 333或微信扫描二维码关注得胜官方公众
号与我们联系。
产品特性
• 全新外观设计，造型新颖时尚，轻巧便携；
• 数字扩音技术，10W大功率音频输出，声音清晰保真；
• 无线播放功能，可连接手机、电脑、PAD等设备播放音乐；
• 具有音乐播放功能，支持U盘、TF卡的多媒体音频播放；
• 具有AUX音频信号输入功能，可充当小音箱使用；
• 内置2000mA可充电锂离子电池，节能环保，续航约15小时；
• 内置MCU智能充电管理系统，防过充保护，使用安全可靠；
• 壳体采用ABS工程原料成型，经久耐用；
• 具有肩挂及腰挂等多种佩戴方式，使用更方便。
1
适用范围
• 适用于教学、导游、培训、促销等场合扩音
E188
技术参数
• 工作电压：DC 3.5-4.2V
• 充电电压：DC 5V/1.5A
• 使用时间：约15小时
• 充电时间：约1.5小时
• 充电方式：Type-C
• 产品规格：100*90*35.5mm
• 产品重量：约200g
• 频率响应：80Hz-18KHz
• 额定功率：5W
• 峰值功率：10W
• 扬声器阻抗：4Ω
• 无线连接版本：5.0以上
• 电池类型：锂离子电池
• 电池规格：3.7V/2000mAh
拾音器音头参数
• 拾音器：背极式驻极体
• 指向性：单指向
• 频率响应：100Hz-12.5KHz
• 灵敏度：-42~-48dB（0dB=1V/Pa，at 1KHz）
产品配置
• ……台
• 有线头戴麦克风 …………..…………………………..………………… 1个
• 肩带…………..…………………..………..………..………………………1条
• 充电线………..……………..………..……..…………………..…………1条
• 说明书………..…………………..………..……..………………..………1份
E188扩音器 …………..…………………..………..………..…… 1
2
注：以上数据由得胜实验室测试得到，并拥有最终解释权！
主机（扩音器）参数
E188
功能示意
扩音器
① ②
③④⑤ ⑥
⑦
⑧
⑨
⑩
⑪
⑫
① 电源开关和音量调节旋钮：向“ON”方向拨动旋钮，听到“哒”一声，表示扩音
器已通电并进入人声扩音状态，此时电源指示灯②亮蓝灯，继续向“ON”方向拨动声
音逐渐增大；反之向“OFF”方向拨动则声音逐渐减少，直至听到“哒”一声关机。
② 电源指示灯：电量充足时，指示灯常亮蓝灯；当指示灯红灯闪烁时，表示扩音器处
于低电量状态，请及时为扩音器充电；充电过程中，指示灯常亮红灯，充满后蓝灯常亮。
③ “M”模式切换键：开机状态下，短按该按键可切换工作模式，并伴有相应的语音提示。
④ 上一曲按键：在蓝牙、U盘、TF卡播放状态下，短按此键为切换上一曲。
⑤ 下一曲按键：在蓝牙、U盘、TF卡播放状态下，短按此键为切换下一曲。
3
US B
DC 5 V AU X MI C
E188
⑥ 播放/暂停按键：短按此按键控制音乐的播放及暂停；在蓝牙播放状态时，长按此键
可以断开蓝牙连接。
⑦ U盘接口：可将储存有音频文件的U盘插入此孔进行播放。
⑧ TF卡接口：按照正确插卡方向插入TF内存卡。插入时，听到“哒”一声，表示已安装到
位；取卡时把卡往下按压，听到“哒”一声，TF内存卡将自动弹出来。
提示：请确保TF卡中储存的是MP3、WAV格式的音频文件，否则不能正常读取歌曲文件甚
至会有损坏机器的风险；拷入歌曲前请先将TF卡按FAT16、FAT32格式进行格式化，其他
方式的格式化（如exFAT、NTFS格式）会导致录音无法保存或者储存的歌曲无法播放。
⑨ MIC输入接口：将有线麦克风插头插入此孔，进入有线人声扩音状态。操作时，请不
要将麦克风的拾音面朝向扩音器的扬声器，以免产生啸叫。
⑩ AUX 输入接口：通过Φ3.5mm音频连接线与手机、电脑、平板等播放设备连接，可将
扩音器作为有源音箱使用。
⑪ 充电接口：连接Type-C充电线为扩音器充电。
⑫ 挂扣：用于安装肩带，可将扩音器斜挂于肩上使用。
4
使用说明
首次使用本机时，需要与手机或蓝牙设备配对连接，步骤如下：
1.先打开扩音器的电源开关，短按“M”键切换为蓝牙模式，此时指示灯蓝灯闪烁，表示
蓝牙正在搜索配对状态。
1.将头戴麦克风正确佩戴于头部，并调整好麦克风的拾音角度；
2.将有线头戴麦克风的Φ3.5mm插头插入扩音器的MIC输入接口内；
3.打开扩音器电源开关，电源指示灯亮蓝灯，调整旋钮至合适音量；
4.在使用过程中，若指示灯红灯闪烁时，表示扩音器电量不足，请及时充电。
提示：初次使用时，建议先充满电；如长时间不使用，需每半年给扩音器充一次电，避免
电池过放，对电池性能产生影响。
一、使用方法
二、蓝牙配对
E188
2.进入手机“设置”菜单，找到蓝牙功能选项，开启手机蓝牙功能，待搜索到“TAKSTAR
E188”,点击“TAKSTAR E188”进行连接，当扩音器语音提示“蓝牙已连接”，此时蓝
灯恢复长亮，表示蓝牙连接成功；手机、电脑、平板等设备蓝牙连接扩音器成功后，即可
实现音乐播放功能。
下次开机后点按“M”键开启蓝牙模式时，如果是已有连接过蓝牙，则自动回连最后一次
使用的蓝牙设备，同时伴有提示音“蓝牙已连接”。
5
安全警示
为避免电击、高温、着火、辐射、爆炸、机械危险以及使用不当等可能造成的人身
伤害或财产损失，使用本产品前，请仔细阅读并遵守以下事项：
1. 使用产品时请确认所连设备与本产品是否匹配以及合理调整音量大小，不要在超过
产品功率及大音量下长时间使用，以免造成产品异常；
2. 使用中若发现有异常（如冒烟、异味等），请立即关闭电源开关并拔掉电源插头，
然后将产品送售后服务网点检修；
3. 消费者若使用电源适配器供电，则应购买配套使用获得CCC认证并满足标准要求
的电源适配器；
4. 本产品及附件都应放置在室内干燥通风处，请勿长期存放在潮湿、灰尘多的环境，
使用中避免靠近火源、雨淋、进水、过度碰撞、抛掷、振动本机及覆盖通风孔，
以免损坏其功能；
5. 若产品需要固定于墙壁或天花板时，请确保固定到位，防止因固定强度不足导致产
品发生跌落危险；
6. 使用该产品时需遵守相关安全规定，法律法规明确禁止使用场合请勿使用本产品，
以免导致意外事故；
7. 请不要自行拆机改装或维修，以防止出现人身伤害，如有问题或服务需求请联系当地
售后服务网点跟进处理。
E188
6
关于图标含义解释
此符号表示，根据WEEE指令(2012/19/EU)和国家法律，由于这种类型的废弃物
会有潜在的有害物质，可能对环境和人类健康产生负面影响，所以本产品不应与
您的家庭垃圾一起处置，应将本产品应交由授权的电气和电子设备（WEEE）回收站回收。
同时，您在正确处理本产品的同时将有助于自然资源的有效利用。如需了解更多有关您
可以在何处放置废物回收设备的信息，请联系您当地的城市办事处、废物管理局或家庭
废物处理服务部门。
关于本说明书
本说明书中内容符合截止印刷之日的技术规格。由于得胜公司会不断改进产品， 本说
明书可能不符合您的特定产品的技术规格。要获取最新版说明书，请访问得胜官网，然后
下载说明书文件。技术规格、设备或另售的附件在各个地区可能有所不同，如有问题请与
当地得胜销售网点确认。如需更多支持和深层产品信息，请浏览得胜官方网站：
https://www.takstar.com
环保说明
E188
Preface
Dear Customer,
Thank you for purchasing Takstar E188 Wired Amplifier – New Edition. To better
understand and use the product, please read this manual carefully. If you have
any questions or suggestions, please contact our local after-sales service.
Features
• Sleek and stylish new design, lightweight and portable.
• Digital amplification with 10W high-power output of high clarity and
fidelity.
• Play music wirelessly from devices such as smartphone, computer and
tablet.
• Supports multimedia audio playback from USB drives and TF cards.
• AUX audio signal input function lets you use it as a small speaker.
• Built-in 2000mAh rechargeable lithium-ion battery with a battery life of
about 15 hours.
• MCU-based smart charging system prevents overcharge and ensures
reliability and safety.
• Rugged and durable casing, made of ABS engineering material.
• Multiple wearing options, such as shoulder-worn and waist-worn, for
added convenience.
7
Application
• Teaching, tour guide, training, sales, etc.
E188
Specifications
Voice Amplifier
• Charging Voltage: DC 5V/1.5A
• Playtime: about 15 hours
• Charging Time: about 1.5 hour
• Charging Port: Type-C
• Dimensions: 100*90*35.5mm
• Weight: about 200g
• Frequency Response: 80Hz-18KHz
• Rated Power: 5W
• Peak Power: 10W
• Speaker Impedance: 4Ω
• Wireless Connection: above V5.0
• Battery Type: li-ion
• Battery Spec: 3.7V/2000mAh
• Working Voltage: DC 3.5-4.2V
Headset Microphone
• Capsule: back electret
• Polar Pattern: unidirectional
• Frequency Response: 100Hz-12.5KHz
• Sensitivity: -42~-48dB (0dB=1V/Pa, at 1KHz)
Package Contents
• E188 Voice Amplifie
•Wired Headset Microphone ………………………………………………………………1 PCS
• Strap ………………………………………………………………………………………………1 PCS
• Charging Cable…………………………………………………………………………………1 PCS
• User Manual ……………………………………………………………………………………1 PCS
…………………………………………………………………………1 PCS
8
Note: The above data are measured by Takstar laboratory which has the final
interpretation right!
E188
Function Descriptions
Voice Amplifier
9
① Power switch & volume dial: Rotate the dial to ON until you hear a click to power
on the device and then gradually increase the volume level. Once powered on,
LED ② will light up blue, meaning the device is ready for voice amplification.
Likewise, rotate to OFF to gradually decrease the volume level and eventually
power off the device.
Power indicator: Blue light when sufficient power; red flashes when low power
and requires charging; red light while charging and blue light when fully charged.
②
① ②
③④⑤ ⑥
⑦
⑧
⑨
⑩
⑪
⑫
US B
DC 5 V AU X MI C
E188
③ M mode button: When powered on, short press to switch work mode,
accompanied by corresponding voice prompt.
④ Previous track button: In Bluetooth, USB, or TF card mode, short press to
switch to the previous track.
⑤ Next track button: In Bluetooth, USB, or TF card mode, short press to switch
to the next track.
⑥ Play/Pause button: Short press to play or pause the music. When playing in
Bluetooth, long press this button to disconnect Bluetooth.
⑦ USB interface: Insert a USB flash drive to play audio files stored in it.
⑧ TF card slot: Insert a TF memory card following the correct direction until you
hear a click to install it in place. To remove the TF card, press it down until it clicks
to eject the card.
Tip: Please make sure the audio files in the TF card are stored in MP3 and/or WAV
format, otherwise it won't be readable and may even damage the device. Please
format the TF card to FAT16 or FAT32 file system before copying songs, because
other file system (e.g., exFAT, NTFS) will cause failure to save recordings or play
songs.
⑨ MIC input: Insert a wired mic to start wired voice amplification. Do not point
the mic capsule towards the loudspeaker to avoid feedback.
⑩ AUX input: Connect to a playback device (e.g., phone, tablet, MP3 player) via
a Ø3.5mm audio cable, so to use the amplifier as an active speaker.
⑪ Charging port: Charge the amplifier via a Type-C charging cable.
⑫ Strap clip: Used to install the shoulder strap for wearing the amplifier across
shoulder.
10
E188
Operation Instructions
I. How to Use
II. Bluetooth pairing
1. Wear the headset mic on your head correctly, and adjust the pickup angle of the
mic.
2. Insert the ø3.5mm plug of the wired headset mic into the MIC input interface.
3. Power up the voice amplifier (LED lights up blue) and adjust the volume to an
appropriate level.
4. If the power indicator flashes red during use, it means that the battery is running
low and requires charging in time.
Tips: It's recommended to fully charge the device upon first use, and if not used for
long periods, charge it for once every six months to avoid battery over-discharge
which could affect battery performance.
Upon first use, you need to connect this device to your phone or Bluetooth device,
following below steps:
1. Power up the amplifier, press [M] to switch to Bluetooth mode and start
Bluetooth discovery and pairing, indicated by a flashing blue LED.
2. Enter SETTINGS menu on your phone, find and enable Bluetooth, wait until
"TAKSTAR E188" is discovered and tap on it to connect. When connected
successfully, there will be a voice prompt about “Bluetooth Connected”, and
the LED will become solid blue. Devices such as cell phones, laptops, and tablets
can play music via Bluetooth thereafter.
3. The next time you switch to Bluetooth mode, the amplifier will automatically
connect to the previously paired device, signaled by a voice prompt “Bluetooth
connected”.
11
E188
12
Safety Instructions
To avoid electric shock, overheat, fire, radiation, explosion, mechanical risk and
injury or property loss due to improper use, please read and observe the
following items before use:
1. Please check if the power of the connected equipment matches with that of
this product before operation. Adjust the volume to proper level during operation.
Do not operate at over-power or high-volume level for extended time to avoid
product malfunction.
2. If there is any abnormality during use (e.g., smoke, strange odor), please kill the
power switch and unplug from power source, then send the product to the local
after-sales service for repair.
3. Power adapter used, if any, should be approved by CCC certification or similar
standards and comply with the power supply requirements.
4. Keep this product and its accessories in a dry and ventilated area. Do not store
in a humid or dusty area for extended time. Keep away from fire, rain, liquid
intrusion, bumping, throwing, vibrating, or from blocking any ventilation openings,
to prevent malfunction.
5. The product must, when installed on walls or ceilings, be fixed firmly in place at
adequate strength to prevent from falling.
6. Please abide by safety rules during operation. Do not use the product in places
prohibited by laws or regulations to avoid accident.
7. Do not disassemble or repair the product by yourself to avoid injury. If you
have any questions or require any services, please contact our local
after-sales service.
E188
13
Label Meanings
This symbol indicates that this product should not be disposed of with your
household waste, according to the WEEE directive (2012/19/EU) and your
national law. This product should be handed over to an authorized collection site
for recycling waste electrical and electronic equipment (WEEE). Improper handling
of this type of waste could have a possible negative impact on the environment
and human health due to potentially hazardous substances that are generally
associated with WEEE. At the same time, your cooperation in the correct disposal
of this product will contribute to the effective usage of natural resources. For more
information about where you can drop off your waste equipment for recycling,
please contact your local city office, waste authority, or your household waste
disposal service.
About This Manual
This manual contains up-to-date technical specifications as of printing. However,
specifications contained herein may not conform to your particular product since
Takstar is constantly improving its products. Also, specifications, devices or
accessories available may vary from region to region. If you have any questions,
please contact our local sales outlet. For the latest version/more information,
please visit our website: https://www.takstar.com/
E188
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
