Metabo KHEV 8-45 BL 取扱説明書

カテゴリー
パワーツール
タイプ
取扱説明書

このマニュアルも適しています

www.metabo.com
KHEV 5-40 BL
KHEV 8-45 BL
KHEV 11-52 BL
MHEV 5 BL
MHE 96-2
PRC 使用说明 5 en Original instructions 9
b
a
1
3
2
4
5
6
6
6
7
987
987
10
12
11
13
14
KHEV...
MHEV...
10
12
11
13
14
2
3
KHEV 5-40 BL
*1) Serial Number: 00765..
KHEV 8-45 BL
*1) Serial Number: 00766..
KHEV 11-52 BL
*1) Serial Number: 00767..
MHEV 5 BL
*1) Serial Number: 00769..
MHE 96-2
*1) Serial Number: 00772..
SDS-max SDS-max SDS-max SDS-max SDS-max
P
1
W 1150 1500 1500 1500 1500
P
2
W 730 750 810 730 810
n
0
/min
0 - 350
0 - 500
0 - 210
0 - 300
0 - 200
0 - 270
--
D
1
mm (in)
40 (1
9
/
16
) 45 (1
25
/
32
) 52 (2
1
/
16
)
--
D
2
mm (in)
105 (4
1
/
8
) 125 (4
15
/
16
) 160 (6
5
/
16
)
--
s
max
/min
bpm
2900 2900 2400 2900 2100
W
(EPTA 05/2009) J 8,7 12,2 18,8 8,7 18,0
C-12 12 12 12 12
mkg (lbs)8,3 (18) 9,8 (22) 12,4 (27) 7,9 (17) 12,2 (27)
a
h,HD
/K
h,HD
m/s
2
8,0 (1,5) 8,6 (1,5) 9,5 (1,5) - -
a
h,Cheq
/K
h,Cheq
m/s
2
7,3 (1,5) 9,2 (1,5) 9,7 (1,5) 7,3 (1,5) 10,3 (1,5)
L
pA/
K
pA
dB (A) 93 / 3 94 / 3 98 / 3 93 / 3 90 / 3
L
WA/
K
WA
dB (A) 104 / 3 105 / 3 110 / 3 104 / 3 101 / 3
L
pA(M)
dB (A) -----
L
WA(M)
dB (A) ----98,4
L
WA(G)
dB (A) - - - - 101,0
13.
*2) 2014/30/EU, 2006/42/EC, 2011/65/EU
*3) EN 60745-1:2009+A11:2010, EN 60745-2-6:2010, EN 50581:2012
2018-09-10, Bernd Fleischmann
Direktor Produktentstehung & Qualität (Vice President Product Engineering & Quality)
*4) Metabowerke GmbH - Metabo-Allee 1 - 72622 Nuertingen, Germany
6.31800
ESA max
6.23271
MHEV...
KHEV...
etc.
.
.
.
etc.
.
.
.
C
B
A
4
5
简体中文 PRC
6.31800
ESA max
6.23271
MHEV...
KHEV...
etc.
.
.
.
etc.
.
.
.
C
B
A
4
使用说明
1. 符合标准声明
为了履行我方责任,我们特此声明,本公司的电
钻和凿锤按类型和序列号 *1) 标识,符合指令 *2)
和标准 *3) 的全部相关要求。*4) 的相关技术文档 -
详见第 3 页。
MHEV...2000/14/EC:符合附录 VI 的一致性评估
程序 (m < 15 kg)。(检测机构:斯洛文尼亚质量与
计量研究院,Trzaska cesta 2SI-1000 Ljubljana
Slovenia(公告机构编号:1304))。
2. 特定使用条件
组合锤 (KHEV...) 与适当的配件搭配使用时,适
用于对混凝土、砖、石材及类似材料进行锤钻和
凿削。
凿锤
(MHEV...) 与适当的配件搭配使用时,适用于
对混凝土、砖、石材及类似材料进行凿削。
用户自行承担因使用不当造成的任何损坏的责任。
必须遵守通用事故预防规章和随附的安全资料。
3. 一般安全说明
为了您自身的安全及保护您的电动工具,
请特别注意标有此符号的所有文本!
警告仔细阅读使用说明可降低受伤风险。
警告阅读所有安全警告和说明。
不遵循
些警告和说明导致电击、火灾和/或严重
保存好所有警告和说明以备查阅。
转交电动工具时,请一并转交这些文件。
4. 特殊安全说明
锤类工具的安全警告:
——戴好耳罩。暴露在噪声中会引起听力损伤。
——使用随工具提供的辅助手柄。操作失手会引
起人身伤害。
——在切削附件可能触及暗线或其自身软线之处
进行操作时,要通过绝缘握持面来握持工具。
削附件碰到带电导线会使工具外露的金属零件带
电从而使操作者受到电击。
在调整、改换、维护或清洁工具前,请将主电源
拔下。
在作业过程中,附加手柄必须正确安装。
始终双手握住工具的规定手柄处,保持安全站
姿,专心工作。
使用此工具时始终佩戴护目镜、手套、防尘面罩
并穿上结实的鞋子。
确保您要使用本工具的地方没有铺设电源电缆、
煤气管道或水管(例如,使用金属探测器检测)。
仅使用正确安装的工具进行作业。拉动工具,检
查其是否准确固定到位。(必须能够将工具沿轴
向移动几厘米。)
在地面上方作业时,请确保您下方的区域无障碍
物。
作业结束后,切勿直接触碰工具或靠近工具的零
件,因为它们的温度会很高,可能导致皮肤灼伤。
始终将电源电缆放置在远离工具背面的位置。
必须更换损坏或破裂的附加手柄。切勿使用存在
问题的附加手柄操纵工具。
固定工件,防止滑动或旋转(例如,可使用螺丝
夹钳固定)。
降低粉尘暴露程度:
警告 - 使用此电动工具进行砂光、切割、研
磨、钻孔及其他施工作业时产生的部分粉尘
可能包含已知可导致癌症、先天缺陷或其他生殖危
害的化学物质。此类化学物质的一些示例包括:
- 含铅油漆中的铅,
- 砖块、水泥及其他石材产品的结晶二氧化硅,
以及
- 经化学处理的木材中的砷和铬。
暴露于此类物质所带来的风险取决于操作人员进
行此类工作的频率。为降低对这些化学物质的暴
露程度:在通风良好的区域作业,并穿戴经过认
证的防护装备,例如专门用于过滤微小颗粒的防
尘面罩等。
这同样适用于由其他材料引起的粉尘,如木材(橡
木或榉木粉尘)、金属、石棉等。已知可导致的
其他疾病包括过敏反应、呼吸系统疾病等。切勿
吸入这些粉尘。
遵守物料、员工、应用和应用地点的相关准则和
国家规定(例如,职业卫生与安全法规、废物处
理规范等)。
6
PRC 简体中文
从源头收集产生的颗粒,避免在周围环境中沉积。
对于特殊作业,使用适当的配件。从而降低肆意
侵入环境的微粒数量。
使用适当的除尘装置。
通过以下措施降低粉尘暴露程度:
- 请勿将逃逸的颗粒和排出的废气流朝向自己或
附近人员,也不要将其朝向沉积的粉尘。
- 使用除尘装置和/或空气净化器。
- 确保工作区域通风良好,使用真空吸尘器保证
工作区域的清洁。吹扫会使粉尘飞散。
- 使用真空吸尘器或水洗防护服。请勿吹、打或
刷防护装备。
5. 概述
请参见第 2 页。
1 夹紧旋钮 *
2 弓形手柄(附加手柄)*
3 附加手柄 *
4 蝶形螺丝(用于调整限深器)*
5 限深器 *
6 工具锁
7 旋钮
8 麦太保 VibraTech (MVT):集成减震系统
9 触发开关
10 用于连续工作的按钮(仅在凿锤工作模式下)
11 手柄
12 电信号指示灯
13 操作指示灯(连接电源后会发出灯信号)
14 用于减小冲击力的按钮(适合软材料作业)
* 取决于型号和设备
6. 首次运行
调试前,请查看额定电源电压及频率(标在
铭牌上)是否与现有的电源相同。
务必在上游安装一个最大脱扣电流为 30 mA
RCD
仅使用最小横截面积为
1.5 mm
2
的延长电缆。延
长电缆必须符合工具的功耗(参见技术规格)。
如果使用电缆导轮,请始终将电缆完全卷起。
6.1 装配弓形手柄或附加手柄
为安全起见,务必使用随附的弓形手柄 (2)
附加手柄 (3)
MHEV...
通过逆时针转动夹紧旋钮
(1) 松开夹紧环。将弓形
手柄 (2) 调整至所需位置和角度。牢牢拧紧夹紧
旋钮。
KHEV...
通过逆时针转动附加手柄 (3) 打开夹紧环。将附加
手柄固定到所需角度。拧紧附加手柄。
7. 使用
7.1 限深器设定
(仅适用于 KHEV 5-40 BL
松开蝶形螺丝
(4)。将限深器 (5) 设定为所需钻孔
深度。重新拧紧蝶形螺丝 (4)
7.2 定位、拆除工具
在插入之前,清洁钻杆并涂抹提供的专用润滑
脂(配件:订单号 6.31800)!仅使用 SDS-
max 工具。
定位工具:
转动工具并将其插入,直至其卡合到位。工具将
自动锁定。
拉动工具,检查其是否准确固定到位。(必
须能够将工具沿轴向移动几厘米。)
卸下工具:
按箭头
(a) 所示方向向后拉工具锁 (6),卸下工具
(b)
7.3 设置操作模式和凿锤位置
安装凿锤后,避免用工具进行撬抬。
在电机完全停止前,请勿激活开关按钮 (7)
转动开关按钮 (7) 选择所需的操作模式。
冲击钻(仅适用于 KHEV...
凿钻
使凿锤旋转至所需位置的设置。
设置凿锤的位置:凿锤可以锁定在不同的位置。
- 插入凿锤。
- 将旋钮 (7) 转到过渡位置
- 将凿锤转到所需位置。
- 将开关按钮 (7) 转到位置
- 转动凿锤,直至其卡合到位。
7
简体中文 PRC
安装凿锤后,仅可在“凿钻”操作模式下操
作工具
7.4 设置冲击力
按下按钮 (14) 改变冲击力(和速度)(但不要在
电机运转时操作)。
按钮 (14) 亮起:减小冲击力、降低速度( 70
按钮 (14) 未亮起:最大冲击力、高速 (100%)
通过反复试验找到正确的设置。例如:如果正在
对软、脆性材料进行作业或者希望降低破损率,
请在“减小冲击力”设置下进行作业。
“最大冲击力”设置可用于处理较硬材料。
7.5 接通和断开
扭矩设置:
按下触发开关 (9) 即可接通工具。
要断开工具,请松开触发开关 (9)
连续工作(仅限于凿钻模式 ):
按下 (10) 按钮后可将工具切换至连续工作模式(仅
限于凿钻模式 )。((10) 按钮亮起。)
要断开工具,再次按下 (10) 按钮。((10) 按钮未
亮起。)
连续工作期间,如果电动工具意外脱手,它
将继续运转。因此,双手必须始终握住工具
的手柄,站稳,专心工作。
7.6 麦太保 VibraTech (MVT)
用于减轻振动,并降低手部压力。
推压工具时,务必在手柄上适度用力,不要用力
过度。中心位置 (8) 减振效果最明显。
8. 清洁与维护
应使用真空吸尘器或通过吹送干燥空气的方式,
经常性的定期彻底清洁电动工具的所有通风口。
进行该操作之前,请切断电动工具的电源并佩戴
防护眼镜和防尘面罩。
9. 故障排除
电信号指示灯 (12)
闪烁 - 重启保护
在停电后恢复供电时,尽管电钻仍处于开启
状态,但为确保安全,并不会使其启动。请将电
钻再次关闭后开启。
持续亮起 - 过载
如果工具长时间过载,则会限制功率输入以
避免电机进一步过热。
使工具空转直至冷却。
10. 配件
只能使用麦太保原厂配件。
仅可使用符合使用说明中所列要求及规格的配件。
请参见第 4 页。
A 钻头和凿锤种类繁多,应用范围广泛
B 专用润滑脂(用于润滑钻杆)
C 除尘系统
有关完整配件列表,请访问 www.metabo.com
查看产品目录。
11.维修
只能由合格的电工修理电动工具!
连接电缆只能由麦太保或授权的客户服务中心进
行更换。
如果需要维修麦太保电动工具,请联系您当地的
麦太保代表。有关具体地址,请参见
www.metabo.com
您可以从 www.metabo.com 下载配件列表。
12.环境保护
有关废弃的工具、包装和配件的环保性处置及回
收,请遵循国家相关规定。
仅适用于欧盟国家/地区:不得将电动工具
与生活垃圾一同处置!根据有关废旧电子和
电气设备的欧盟指令 2002/96/EC 及其在国家法律
系统中的实施方案,废旧的电动工具必须单独收
集和上交,从而以环保的方式回收。
13. 技术规格
对规格的解释性说明请见第 3 页。保留因技术发展
而进行变更的权利。
P
1
= 额定输入功率
P
2
= 输出功率
n
0
= 空载转速
D
1
= 使用冲击石材钻头钻入混凝土的最大钻
孔直径
D
2
= 使用冲击岩心切割机钻入混凝土的最大
钻孔直径
8
PRC 简体中文
s
max
= 最大冲击率
W = 单次冲击力
C = 凿钻位置的数量
m = 不含电源电缆的重量
测量值依照 EN 60745 确定。
工具的防护等级为 II
~ 交流电
引用的技术资料皆含有公差值在内(依照相关有
效标准)。
排放值
这些值可用来评估电动工具的排放量,以及
比较不同的电动工具。根据操作条件、使用的电
动工具及配件的情况,实际载荷可能会更高或更
低。当载荷较低,无法进行评估时,请让工具休
息一下。根据调整后的估计值,为使用者安排保
护措施,例如组织措施。
振动总值(三个方向的矢量和)依据 EN 60745
确定:
a
h, HD
= 振动排放值(使用锤钻对混凝土进行
钻孔)
a
h, Cheq
= 振动排放值(凿钻)
K
h,HD/Cheq
= 不确定(振动)
典型 A 荷重声音等级:
L
pa
= 声压等级
L
WA
= 声功率等级
K
pA
, K
WA
= 不确定(噪声等级)
L
pA(M)
= 根据 2000/14/EG 在用户耳处测量的噪声
等级
L
WA(M)
= 根据 2000/14/EG 测量的声功率等级
L
WA(G)
= 保证声功率等级符合 2000/14/EC
操作过程中,噪音等级可能超过 80 dB(A)
佩戴护耳器!
9
ENGLISH en
Original instructions
On our own responsibility, we hereby declare that
this drilling and chisel hammer, identified by type
and serial number *1), meets all relevant
requirements of directives *2) and standards *3).
Technical documents for *4) - see page 3.
MHEV...:2000/14/EC: Conformity assessment
procedures in accordance with Annex VI (m < 15
kg). (Testing agency: Slovenian Institute of Quality
and Metrology, Trzaska cesta 2, SI-1000 Ljubljana,
Slovenia (Notified Body No.: 1304)).
The combination hammer (KHEV...) is designed for
hammer drilling and chiselling in concrete, bricks,
stone and similar materials when used in
combination with appropriate accessories.
The chisel hammer (MHEV...) is designed for
chiselling in concrete, bricks, stone and similar
materials when used in combination with
appropriate accessories.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNINGRead the operating
instructions to reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Always include these documents when passing on
your power tool.
Wear ear protectors. Exposure to noise can
cause hearing loss.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Contact with a live wire will make
exposed metal parts of the tool live and shock the
operator.
Pull the plug out of the socket before making any
adjustments, changing tools, carrying out
maintenance or cleaning.
Always work with the additional handle correctly
installed.
Always hold the machine with both hands on the
intended handles, take a secure stance and
concentrate on the work.
Always wear protective goggles, gloves, a dust
mask and sturdy shoes when working with this tool.
Ensure that the place where you wish to work is free
of power cables, gas lines or water pipes (e.g.
check using a metal detector).
Work only with a correctly fitted tool. Pull on the tool
to check that it is correctly seated. (It must be
possible to move the tool a few centimetres in an
axial direction.)
When working above ground level, ensure that the
area below you is clear.
Never touch the tool or parts near the tool directly
after work because they may be extremely hot and
can cause burns to the skin,
Always position the power cable so that it leads
away from the back of the machine.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
Secure the workpiece to prevent slipping or rotation
(e.g. by securing with screw clamps).
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
-Lead from lead-based paints,
-Crystalline silica from bricks and cement and
other masonry products, and
-Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well-
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
1. Declaration of Conformity
2. Specified Conditions of Use
3. General Safety Information
4. Special Safety Instructions
10
ENGLISHen
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
-do not direct the escaping particles and the
exhaust air stream towards yourself or nearby
persons or towards dust deposits,
-use an extraction unit and/or air purifiers,
-ensure good ventilation of the workplace and keep
it clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
-Vacuum or wash protective clothing. Do not blow,
beat or brush protective gear.
See page 2.
1Clamping knob *
2Bow handle (additional handle) *
3Additional handle *
4Wing screw (for adjusting the depth stop) *
5Depth stop *
6Tool lock
7Knob
8Metabo VibraTech (MVT): integrated damping
system
9Trigger
10 Button for continuous operation (only in chisel
operating mode)
11 Handle
12 Electronic signal indicator
13 Operating indicator (light signal if mains power
is connected)
14 Button for reduced impact force (for working in
soft material)
* model-dependent, equipment-dependent
Before commissioning, check that the rated
mains voltage and mains frequency stated on
the type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Use only extension cables with a minimum cross-
section of 1.5mm
2
. Extension cables must
correspond to the power consumption of the
machine (cf Technical Specifications). If a cable
roller is used, always roll up the cable completely.
6.1Assembly of the bow handle or
additional handle
For safety reasons, always use the bow
handle (2) or additional handle (3) supplied.
MHEV...:
Release the clamping ring by turning the clamping
knob (1) anticlockwise. Adjust the bow handle (2) to
the required position and angle. Tighten the
clamping knob firmly.
KHEV...:
Open the clamping ring by turning the additional
handle (3) anticlockwise. Secure the additional
handle at the required angle. Tighten the additional
handle.
7.1Depth Stop Setting
(Only for KHEV 5-40 BL)
Release the wing (4) screw. Set the depth stop (5)
to the required drilling depth. Retighten the wing
screw (4).
7.2Positioning, removing tool
Before inserting, clean tool shank and apply
supplied special grease (accessories: Order
no. 6.31800)! Use only SDS-max tools.
Positioning tool:
Turn tool and insert until it engages. The tool is
automatically locked.
Pull on the tool to check that it is correctly
seated. (It must be possible to move the tool a
few centimetres in an axial direction.)
Remove the tool:
Pull the tool lock (6) backwards in direction
indicated by arrow(a) and remove tool (b).
7.3Setting operating mode and chisel
position
Avoid levering with the machine when a chisel
is fitted.
Do not activate the switch button (7) until the
motor has completely stopped.
Turn the switch button (7) to select the desired
operating mode.
Impact drilling (only for KHEV...)
Chiselling
Setting which enables the chisel to be rotated
to the desired position.
Setting the position of the chisel:
The chisel can be
locked in different positions.
-Insert the chisel.
-Turn the knob (7) to the interim position .
-Turn the chisel to the required position.
-Turn the switch button (7) to position .
-Turn the chisel until it engages.
When a chisel is fitted, only operate the
machine in the chiselling operating mode .
7.4Setting impact force
Press the button (14) to change the impact force
(and the speed) (but not while the motor is running).
Button (14) illuminated: reduced impact force,
reduced speed (approx. 70%)
Button (14) not illuminated: maximum impact
force,
high speed (100%)
5. Overview
6. Initial Operation
7. Use
11
ENGLISHen
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
-do not direct the escaping particles and the
exhaust air stream towards yourself or nearby
persons or towards dust deposits,
-use an extraction unit and/or air purifiers,
-ensure good ventilation of the workplace and keep
it clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
-Vacuum or wash protective clothing. Do not blow,
beat or brush protective gear.
See page 2.
1Clamping knob *
2Bow handle (additional handle) *
3Additional handle *
4Wing screw (for adjusting the depth stop) *
5Depth stop *
6Tool lock
7Knob
8Metabo VibraTech (MVT): integrated damping
system
9Trigger
10 Button for continuous operation (only in chisel
operating mode)
11 Handle
12 Electronic signal indicator
13 Operating indicator (light signal if mains power
is connected)
14 Button for reduced impact force (for working in
soft material)
* model-dependent, equipment-dependent
Before commissioning, check that the rated
mains voltage and mains frequency stated on
the type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Use only extension cables with a minimum cross-
section of 1.5mm
2
. Extension cables must
correspond to the power consumption of the
machine (cf Technical Specifications). If a cable
roller is used, always roll up the cable completely.
6.1Assembly of the bow handle or
additional handle
For safety reasons, always use the bow
handle (2) or additional handle (3) supplied.
MHEV...:
Release the clamping ring by turning the clamping
knob (1) anticlockwise. Adjust the bow handle (2) to
the required position and angle. Tighten the
clamping knob firmly.
KHEV...:
Open the clamping ring by turning the additional
handle (3) anticlockwise. Secure the additional
handle at the required angle. Tighten the additional
handle.
7.1Depth Stop Setting
(Only for KHEV 5-40 BL)
Release the wing (4) screw. Set the depth stop (5)
to the required drilling depth. Retighten the wing
screw (4).
7.2Positioning, removing tool
Before inserting, clean tool shank and apply
supplied special grease (accessories: Order
no. 6.31800)! Use only SDS-max tools.
Positioning tool:
Turn tool and insert until it engages. The tool is
automatically locked.
Pull on the tool to check that it is correctly
seated. (It must be possible to move the tool a
few centimetres in an axial direction.)
Remove the tool:
Pull the tool lock (6) backwards in direction
indicated by arrow(a) and remove tool (b).
7.3Setting operating mode and chisel
position
Avoid levering with the machine when a chisel
is fitted.
Do not activate the switch button (7) until the
motor has completely stopped.
Turn the switch button (7) to select the desired
operating mode.
Impact drilling (only for KHEV...)
Chiselling
Setting which enables the chisel to be rotated
to the desired position.
Setting the position of the chisel:
The chisel can be
locked in different positions.
-Insert the chisel.
-Turn the knob (7) to the interim position .
-Turn the chisel to the required position.
-Turn the switch button (7) to position .
-Turn the chisel until it engages.
When a chisel is fitted, only operate the
machine in the chiselling operating mode .
7.4Setting impact force
Press the button (14) to change the impact force
(and the speed) (but not while the motor is running).
Button (14) illuminated: reduced impact force,
reduced speed (approx. 70%)
Button (14) not illuminated: maximum impact
force,
high speed (100%)
5. Overview
6. Initial Operation
7. Use
ENGLISH en
The correct setting is found by trial and error.
Example: if work is being completed on soft, brittle
material or if you want to keep breakage to a low
level, work at “reduced impact force”.
Use the “maximum impact force” setting for working
with harder materials.
7.5Switching on and off
Torque setting:
Press the trigger switch (9) to switch on the
machine.
To switch off release the trigger switch (9).
Continuous operation (only in chiselling
mode ):
The machine can be switched to continuous
operation (only in chiselling mode ) by pressing
the (10) button. ( (10) button illuminated.)
To switch off, press the (10) button once again. (
(10) button not illuminated.)
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
7.6Metabo VibraTech (MVT)
For reduced vibrations and less stress on the
hands.
Always apply a moderate amount of pressure to the
handle when pushing down the machine and do not
force. Vibrations are reduced most effectively at the
central position (8).
The power tool should be cleaned regularly, often
and thoroughly through all air vents using a vacuum
cleaner or by blowing in dry air. Prior to this
operation, separate the power tool from the power
source and wear protective glasses and dust mask.
Elektronic signal indicator (12)
Flashing - restart protection
When power is restored after a power failure,
the machine - which is still switched on - will
not start for safety reasons. Switch machine on and
off again.
Continuously illuminated - overload
If the machine is overloaded for a long period
of time, the power intake is limited to avoid
further excessive heating of the motor.
Allow the machine to run at idle speed until it has
cooled off and the electronic signal indicator goes
out.
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
See page 4.
AExtensive drill bit and chisel assortment for a
wide range of applications.
BSpecial grease (for lubricating the tool shanks)
CDust extraction system
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must ONLY be carried out
by qualified electricians!
The connection cable must only be replaced by
Metabo or an authorised customer service
workshop.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national legal systems.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P
1
=Rated input power
P
2
=Power output
n
0
=No-load speed
D
1
=Max. drilling diameter in concrete with
impact masonry bits
D
2
=Max. drilling diameter in concrete with
impact core cutters
s
max
=Maximum impact rate
W=Single impact force
C=Number of chisel positions
m=Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ AC power
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
8. Cleaning, Maintenance
9. Troubleshooting
10. Accessories
11. Repairs
12. Environmental Protection
13. Technical Specifications
12
ENGLISHen
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Total vibration value
(vector sum of three directions)
determined in accordance with EN 60745:
a
h, HD
=Vibration emission value (hammer drilling
into concrete)
a
h, Cheq
=Vibration emission value (chiselling)
K
h,HD/Cheq
= Uncertainty (vibration)
Typical A-effective perceived sound levels:
L
pa
= Sound-pressure level
L
WA
=Acoustic power level
K
pA
, K
WA
= Uncertainty (noise level)
L
pA(M)
=measured noise level according to 2000/
14/EG at the user's ear
L
WA(M)
=Measured acoustic power level as per
2000/14/EG
L
WA(G)
=Guaranteed acoustic power level as per
2000/14/EC
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
ENGLISHen
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Total vibration value (vector sum of three directions)
determined in accordance with EN 60745:
a
h, HD
=Vibration emission value (hammer drilling
into concrete)
a
h, Cheq
=Vibration emission value (chiselling)
K
h,HD/Cheq
= Uncertainty (vibration)
Typical A-effective perceived sound levels:
L
pa
= Sound-pressure level
L
WA
=Acoustic power level
K
pA
, K
WA
= Uncertainty (noise level)
L
pA(M)
=measured noise level according to 2000/
14/EG at the user's ear
L
WA(M)
=Measured acoustic power level as per
2000/14/EG
L
WA(G)
=Guaranteed acoustic power level as per
2000/14/EC
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
Metabowerke GmbH
Metabo-Allee 1
72622 Nuertingen
Germany
www.metabo.com
170 27 6220 - 0119
C997353 21
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Metabo KHEV 8-45 BL 取扱説明書

カテゴリー
パワーツール
タイプ
取扱説明書
このマニュアルも適しています