SCH10
Page 4
页 15
頁 24
페이지
33
หน้า
43
English (original instruction)
简体中文
繁體中文
한국어
ภาษาไทย
ENGLISH (Original Instructions)
2
5
3
82
1
4
11
SC101
SB10D
7
1O
7
6
A
B
9
3
ENGLISH (Original Instructions)
3
11
4
CD
EF
G H
6
7
ENGLISH (Original Instructions)
4
INTENDED USE
Your Stanley SCH10 12V Max Li-Ion Impact Drill has been
designed for light fastening, drilling in wood/metal/brick-
work, and screwdriving applications.
SAFETY INSTRUCTIONS
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING: Indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
Warning: To reduce the risk of injury, read the
instruction manual.
General Power Tool Safety Warnings
@
WARNING Read all safety warnings,
instructions, illustrations and specica-
tions provided with this power tool.
Failure to follow all instructions listed
below may result in electric shock, re
and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
b. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energising power tools that have the switch
on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
5
ENGLISH (Original Instructions)
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5. Battery tool use and care
a. Recharge only with the charger specied by the
manufacturer. A charger A charger that is suitable for
one type of battery pack may create a risk of re when
used with another battery pack.
b. Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
c. When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a re.
d. Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact
accidentally occurs, ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns. .
e. Do not use a battery pack or tool that is damaged
or modied. Damaged or modied batteries may
exhibit unpredictable behaviour resulting in re,
explosion or risk of injury.
f. Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or
temperature above 130 °C may cause explosion.
NOTE The temperature 130 °C can be replaced by
the temperature 265 °F.
g. Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging
improperly or at temperatures outside the specied
range may damage the battery and increase the risk
of re.
6. Service
a. Have your power tool serviced by a qualied repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
b. Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorized service providers.
ADDITIONAL SPECIFIC SAFETY RULES
• Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
ENGLISH (Original Instructions)
6
• Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
SAFETY INSTRUCTIONS WHEN USING LONG DRILL BITS
a. Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit
is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
b. Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher speeds,
the bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
c. Apply pressure only in direct line with the bit and
do not apply excessive pressure. Bits can bend
causing breakage or loss of control, resulting in
personal injury.
RESIDUAL RISKS
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of personal injury due to flying particles.
– Risk of burns due to accessories becoming hot during
operation.
– Risk of personal injury due to prolonged use.
LABELS ON TOOL
The label on your tool may include the following symbols:
: WARNING! To reduce the risk of injury, the user
must read the instruction manual.
Do not stare at operating lamp.
POSITION OF DATE CODE
The Date Code, which also includes the year of manufac-
ture, is printed into the housing.
Example：
2022 XX JN
Year of manufacturing
IMPORTANT SAFETY INSTRUCTIONS FOR ALL
BATTERY CHARGERS
SAVE THESE INSTRUCTIONS: This manual contains
important safety and operating instruc tions for the SC101
battery chargers.
• Before using charger, read all instructions and
cautionary markings on charger, battery pack, and
product using battery pack.
WARNING: Shock hazard. Do not allow any
liquid to get inside charger. Electric shock may
result.
CAUTION: Burn hazard. To reduce the risk
of injury, charge only STANLEY rechargeable
batteries. Other types of batteries may burst
causing personal injury and damage.
CAUTION: Children should be supervised
to ensure that they do not play with the
appliance.
NOTICE: Under certain conditions, with the
charger plugged in to the power supply, the
charger can be shorted by foreign material.
Foreign materials of a conductive nature
such as, but not limited to, grinding dust,
metal chips, steel wool, aluminum foil, or any
buildup of metallic particles should be kept
away from charger cavities. Always unplug the
charger from the power supply when there is
no battery pack in the cavity. Unplug charger
before attempting to clean.
• This appliance is not intended for use by persons
(including children) with reduced physical,sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
• DO NOT attempt to charge the battery pack with
any chargers other than the ones in this manual.
The charger and battery pack are specifically designed
to work together.
• These chargers are not intended for any uses other
than charging STANLEY rechargeable batteries.
Any other uses may result in risk of fire, electric shock
or electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when disconnecting
charger. This will reduce risk of damage to electric plug
and cord.
• Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
• Do not use an extension cord unless it is
absolutely necessary. Use of improper extension
7
ENGLISH (Original Instructions)
cord could result in risk of fire, electric shock, or
electrocution.
• Do not place any object on top of charger or place
the charger on a soft surface that might block the
ventilation slots and result in excessive internal
heat. Place the charger in a position away from any
heat source. The charger is ventilated through slots in
the top and the bottom of the housing.
• Do not operate charger with damaged cord or plug
— have them replaced immediately.
• Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way. Take it to an authorised service centre.
• Do not disassemble charger; take it to an
authorised service centre when service or repair is
required. Incorrect reassembly may result in a risk of
electric shock, electrocution or fire.
• In case of damaged power supply cord the supply cord
must be replaced immediately by the manufacturer, its
service agent or similar qualified person to prevent any
hazard.
• Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk
of electric shock. Removing the battery pack will not
reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard
household electrical power. Do not attempt to use
it on any other voltage. This does not apply to the
vehicular charger.
Batteries
• Never attempt to open for any reason.
• Do not expose the battery to water.
• Do not store in locations where the temperature may
exceed 40 °C.
• Charge only at ambient temperatures between 10
°C and 40 °C.
• Charge only using the charger provided with the tool.
• When disposing of batteries, follow the instructions
given in the section "Protecting the environment".
Chargers
• Use your STANLEY charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and
damage.
• Never attempt to charge non-rechargeable batteries.
• Have defective cords replaced immediately.
• Do not expose the charger to water.
• Do not open the charger.
• Do not probe the charger.
SAVE THESE INSTRUCTIONS
Chargers
The SC101 chargers accept 12V Max Li-Ion batteries.
These chargers require no adjustment and are designed to
be as easy as possible to operate.
Charging Procedure (Fig. B)
1. Plug the charger (10) into an appropriate outlet before
inserting battery pack.
2. Insert the battery pack (7) into the charger. The
charging light will blink continuously indicating that the
charging process has started.
3. The completion of charge will be indicated by the
charging light remaining ON continuously. The pack is
fully charged and may be used at this time or left in the
charger.
NOTE: To ensure maximum performance and life of Li-Ion
batteries, charge the battery pack fully before first use.
Charging Process
Refer the table below for the state of charge of the battery
pack.
State of charge SC101
charginggreen blink
fully chargedgreen solid
hot/cold pack
defect battery
red blink
red solid
HOT/COLD PACK DELAY
When the charger detects a battery that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, as shown
in 'State of charge', suspending charging until the battery
has reached an appropriate temperature. The charger then
automatically switches to the pack charging mode. This
feature ensures maximum battery life.
LI-ION BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the Li-Ion battery on
the charger until it is fully charged.
ENGLISH (Original Instructions)
8
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure to
include catalog number and voltage.
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the safety
instructions below. Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the
battery from the charger may ignite the dust or fumes.
• Never force battery pack into charger. Do not
modify battery pack in any way to fit into a non-
compatible charger as battery pack may rupture
causing serious personal injury.
• Charge the battery packs only in STANLEY chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in
locations where the temperature may reach or
exceed 40 ˚C (105 ˚F) (such as outside sheds or
metal buildings in summer).
WARNING: Never attempt to open the battery
pack for any reason. If battery pack case
is cracked or damaged, do not insert into
charger. Do not crush, drop or damage battery
pack. Do not use a battery pack or charger
that has received a sharp blow, been dropped,
run over or damaged in any way (i.e., pierced
with a nail, hit with a impact, stepped on).
Electric shock or electrocution may result.
Damaged battery packs should be returned to
service centre for recycling.
CAUTION: When not in use, place tool
on its side on a stable surface where it
will not cause a tripping or falling hazard.
Some tools with large battery packs will stand
upright on the battery pack but may be easily
knocked over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion) BATTERY
• Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
materials are created when lithium ion battery packs
are burned.
• If battery contents come into contact with the skin,
immediately wash area with mild soap and water.
If battery liquid gets into the eye, rinse water over the
open eye for 15 minutes or until irritation ceases. If
medical attention is needed, the battery electrolyte is
composed of a mixture of liquid organic carbonates and
lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may
be flammable if exposed to sp ark or flame.
TRANSPORTATION
STANLEY batteries comply with all applicable shipping
regulations as prescribed by industry and legal standards
which include UN Recommendations on the Transport of
Dangerous Goods; International Air Transport Association
(IATA) Dangerous Goods Regulations, International
Maritime Dangerous Goods (IMDG) Regulations, and the
European Agreement Concerning The International Carriage
of Dangerous Goods by Road (ADR). Lithium-ion cells
and batteries have been tested to section 38.3 of the UN
Recommendations on the Transport of Dangerous Goods
Manual of Tests and Criteria.
In most instances, shipping a STANLEY battery pack will
be excepted from being classified as a fully regulated Class
9 Hazardous material. In general, the two instances that
require shipping Class 9 are:
1. Air shipping more than two STANLEY lithium-ion
battery packs when the package contains only battery
packs (no tools), and
2. Any shipment containing a lithium-ion battery with an
energy rating greater than 100 watt hours (Wh). All
lithium-ion batteries have the watt hour rating marked
on the pack.
Regardless of whether a shipment is considered excepted
or fully regulated, it is the shipper's responsibility to consult
the latest regulations for packaging, labeling/marking and
documentation requirements.
Transporting batteries can possibly cause fire if the battery
terminals inadvertently come in contact with conductive
materials. When transporting batteries, make sure that the
battery terminals are protected and well insulated from
materials that could contact them and cause a short circuit.
The information provided in this section of the manual is
provided in good faith and believed to be accurate at the time
the document was created. However, no warranty, expressed
9
ENGLISH (Original Instructions)
or implied, is given. It is the buyer’s responsibility to ensure
that its activities comply with the applicable regulations.
Battery Pack
BATTERY TYPE
The SCH10 operates on a 12V Max battery pack.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is cool and dry
away from direct sunlight and excess heat or cold. For
optimum battery performance and life, store battery
packs at room temperature when not in use.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool, dry place out of the
charger for optimal results.
NOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels
on the charger and the battery pack may show the following
pictographs:
Read instruction manual before use.
See Technical Data for charging time.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Do not expose to water.
Have defective cords replaced immediately.
Charge only between 10 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care for the
environment.
Charge STANLEY battery packs only with
designated STANLEY chargers. Charging
battery packs other than the designated
STANLEY batteries with a STANLEY charger
may make them burst or lead to other
dangerous situations.
Do not incinerate the battery pack.
PACKAGE CONTENTS
The package contains:
1 Impact drill/driver
1 Charger
2 Batteries (D2) or 1 Battery (D1)
1 Instruction manual
NOTE: Battery packs and chargers are not included with
N-models.
• Check for damage to the tool, parts or accessories
which may have occurred during transport.
• Take the time to thoroughly read and understand this
manual prior to operation.
DESCRIPTION (Fig. A)
WARNING: Never modify the power tool or
any part of it. Damage or personal injury could
result.
1. Variable speed trigger switch
2. Forward/reverse button
3. Torque adjustment collar
4. Gear shifter
5. Keyless chuck
6. Battery release button
7. Battery pack
8. Worklight
9. Fuel Gauge
10. Charger
11. Function collar
ELECTRICAL SAFETY
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds
to the voltage on the rating plate. Also make sure that the
voltage of your charger corresponds to that of your mains.
SC101
ENGLISH (Original Instructions)
10
Your STANLEY charger is double insulated in
accordance with IEC60335; therefore no earth
wire is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the STANLEY
service organisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1 mm2; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
Assembly and adjustments
WARNING: Prior to assembly and
adjustment, always remove the battery pack.
Always switch off the tool before inserting or
removing the battery pack.
WARNING: Use only STANLEY battery packs
and chargers.
Inserting and Removing the
Battery Pack from the Tool (Fig. C)
WARNING: To reduce the risk of serious
personal injury, place the forward/reverse
button in the lock-off position or turn tool
off and disconnect battery pack before
making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
NOTE: Make sure your battery pack (7) is fully charged.
FITTING AND REMOVING THE BATTERY
To fit the battery (7), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push
until the battery snaps into place.
To remove the battery, push the release buttons (6)
while at the same time pulling the battery out of the
receptacle.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of serious
personal injury, place the forward/reverse
button in the lock-off position or turn tool
off and disconnect battery pack before
making any adjustments or removing/
installing attachments or accessories.
Proper Hand Position (Fig. A, H)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the main handle
(9).
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the trigger switch (1). To turn
the tool off, release the trigger switch. Your tool is equipped
with a brake. The chuck will stop when the trigger switch is
fully released.
The variable speed switch enables you to select the best
speed for a particular application. The further you squeeze
the trigger, the faster the tool will operate. For maximum tool
life, use variable speed only for starting holes or fasteners
NOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should be
avoided.
Forward/Reverse Control Button
(Fig. A)
A forward/reverse control button (
2
) determines the direction
of the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right side
of the tool.
To select reverse, depress the forward/reverse control button
on the left side of the tool. The center position of the control
button locks the tool in the off position. When changing the
position of the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
Worklight (Fig. A)
There is a worklight (8) located under the torque adjustment
collar (3). The worklight will be activated when the trigger
switch is squeezed.
11
ENGLISH (Original Instructions)
NOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Fuel Gauge (Fig. A)
The tool includes a fuel gauge. When the trigger switch is
pressed, the LED lights will indicate the approximate level of
charge remaining.
Torque Adjustment Collar (Fig. A)
Turn (
11
) to screw symbol. The torque adjustment collar (
3
) is
clearly marked with numbers and a drill bit symbol.The collar
should be rotated until the desired setting is located at the
top of the tool. Locators are provided in the collar to eliminate
the guess work when selecting fastening torque. The higher
the number on the collar, the higher the torque and the larger
the fastener which can be driven. To lock the clutch for drilling
operations, move function collar(
11
) to drill bit position.
NOTE:
When using the Impact drill/driver for drilling holes, be
sure that the function collar is set so the figure of the drill is
aligned with the center line on the top of the tool. Failure to do
this will allow the clutch to slip while attempting to drill.
Dual Range Gearing (Fig. A, D)
The dual range feature of your driver/drill allows you to shift
gears for greater versatility.
To select the low speed, high torque setting, turn the tool off
and permit to stop. Slide the gear shifter (
4
) forward (towards
the chuck). To select the high speed, low torque setting, turn
the tool off and permit to stop. Slide the gear shifter back
(away from chuck).
NOTE:
Do not change gears when the tool is running. If you
are having trouble changing gears, make sure that the dual
range gear shifter is either completely pushed forward or
completely pushed back.
Keyless Single Sleeve Chuck (Fig. E)
Your tool features a keyless chuck with one rotating sleeve for
one-handed operation of the chuck. To insert a drill bit or other
accessory, follow these steps.
1. Lock the trigger in the OFF position as previously
described.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 19 mm (3/4") into the chuck
and tighten securely by rotating the chuck sleeve
clockwise with one hand while holding the tool with the
other. Your tool is equipped with an automatic spindle
lock mechanism. This allows you to open and close the
chuck with one hand.
To release the accessory, repeat step 2 above.
WARNING:
Do not attempt to tighten drill
bits (or any other accessory) by gripping the
front part of the chuck and turning the tool
on. Damage to the chuck and personal injury
may result. Always lock off trigger switch when
changing acces sories.
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximum tightness.
CHUCK REMOVAL (Fig. F)
Turn the adjustment collar to the “drill” position and gear
shifter to position 1 (low speed). Tighten the chuck around
the shorter end of a hex key (not supplied) of 6.35 mm (1/4")
or greater size. Using a wooden mallet or similar object,
strike the longer end in the clockwise direction, as shown.
This will loosen the screw inside the chuck.
Open chuck jaws fully, insert screwdriver (or Torx tool if
required) into front of chuck between jaws to engage screw
head. Remove screw by turning clockwise (left-hand-thread).
Place hex key in chuck and tighten, as shown in Fig F.
Using a wooden mallet or similar object, strike key sharply in
the counterclockwise direction. This will loosen the chuck so
that it can be unscrewed by hand.
CHUCK INSTALLATION (Fig. G)
Screw the chuck on by hand as far as it will go and insert
screw (left-hand thread). Tighten screw securely. Tighten the
chuck around the shorter end of a 6.35 mm (1/4") or larger
hex key (not supplied) strike the longer end in the clockwise
direction with a wooden mallet, as shown. Tighten the screw
once again by turning in a counterclockwise direction.
Drill Operation
WARNING: To reduce the risk of serious
personal injury, turn tool off and disconnect
tool from power source before making
any adjustments or removing/installing
attachments or accessories.
WARNING: To reduce the risk of personal
injury, ALWAYS ensure workpiece is
anchored or clamped firmly. If drilling thin
material, use a wood “back-up” block to
prevent damage to the material.
Turn the collar to the drill bit symbol for drilling. Select the
desired speed/torque range using the gear shifter to match the
speed and torque to the planned operation.
1. Use sharp drill bits only. For WOOD, use twist drill bits,
spade bits, or hole saws. For METAL, use high-speed
steel (HHS) twist drill bits or hole saws.
ENGLISH (Original Instructions)
12
2. Always apply pressure in a straight line with the bit.
Use enough pressure to keep drill biting, but do not
push hard enough to stall the motor or deflect the bit.
3. Hold tool firmly with both hands to control the twisting
action of the drill.
WARNING: The drill may stall if overloaded
causing a sudden twist. Always expect the
stall. Grip the drill firmly with both hands to
control the twisting action and avoid injury.
4. IF DRILL STALLS, it is usually because it is
being overloaded or improperly used. RELEASE
TRIGGER IMMEDIATELY, remove drill bit from work,
and determine cause of stalling. DO NOT CLICK
TRIGGER ON AND OFF IN AN ATTEMPT TO START
A STALLED DRILL — THIS CAN DAMAGE THE
DRILL.
5. To minimize stalling or breaking through the material,
reduce pressure on drill and ease the bit through the
last fractional part of the hole.
6. Keep the motor running when pulling the bit back out
of a drilled hole. This will help prevent jamming.
7. With variable speed drills there is no need to center
punch the point to be drilled. Use a slow speed to
start the hole and accelerate by squeezing the trigger
harder when the hole is deep enough to drill without
the bit skipping out.
Impact drill Operation (Fig. D)
1. Turn the collar (11) to the Impact drill symbol.
2.
Select the high speed setting by sliding the selector
forward (towards the chuck). Important: Use carbide-
tipped or masonry bits only.
3.
Drill with just enough force on the Impact to keep
it from bouncing excessively or “rising” off the bit.
Too much force will cause slower drilling speeds,
overheating and lower drilling rate.
4.
Drill straight, keeping the bit at a right angle to the
work. Do not exert side pressure on the bit when
drillling as this will cause clogging of the bit flutes and
a slower drilling speed.
5.
When drilling deep holes, if the Impact speed starts to
drop off, pull the bit partially out of the hole with tool stil
running to help clear debris from the hole.
NOTE: A smooth, even flow of dust from the hole indicates
proper drilling rate.
Operation as a Screwdriver
Select the desired speed/torque range using the dual range
gear shifter on the top of tool to match the speed and torque
to the planned operation.
Insert the desired fastener accessory into the chuck as you
would any drill bit. Make a few practice runs in scrap or
unseen areas to determine the proper position of the clutch
collar.
MAXIMUM RECOMMENDED CAPACITIES
Low Range–1 High Range–2
Bits, Metal
Drilling 6.00 mm 3.00 mm
Wood, Flat
Boring 19.00 mm 12.00 mm
Hole Saws 19.00 mm 16.00 mm
Brickwork 6.00 mm
MAINTENANCE
Your STANLEY power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious
personal injury, place the forward/reverse
button in the lock-off position or turn tool
off and disconnect battery pack before
making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
The charger and battery pack are not serviceable. There are
no serviceable parts inside.
LUBRICATION
Your power tool requires no additional lubrication.
CLEANING
WARNING: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust
mask when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the
13
ENGLISH (Original Instructions)
materials used in these parts. Use a cloth
dampened only with water and mild soap.
Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the
charger from the AC outlet before cleaning.
Dirt and grease may be removed from the
exterior of the charger using a cloth or soft
non-metallic brush. Do not use water or any
cleaning solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by STANLEY, have not
been tested with this product, use of such
accessories with this tool could be hazardous.
To reduce the risk of injury, only STANLEY,
recommended accessories should be used
with this product.
Consult your dealer for further information on the appropriate
accessories.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you nd one day that your STANLEY product
needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials
helps prevent environmental pollution and
reduces
the demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care
for our environment:
• Run the battery pack down completely, then remove it
from the tool.
• Li-Ion cells are recyclable. Take them to your dealer or
a local recycling station. The collected battery packs
will be recycled or disposed of properly.
REMARKS
Stanley's policy is one of continuous improvement to our
products and as such, we reserve the right to modify product
specifications without prior notice.
• Standard equipment and accessories may vary by
country.
• Product specifications may differ by country.
• Complete product range may not be available in all
countries. Contact your local Stanley dealers for range
availability.
ENGLISH (Original Instructions)
14
TECHNICAL DATA
Li-Ion IMPACT DRILL SCH10
Voltage V
DC
10.8V (12V Max)
No-load speed:
1st gear min
-1
0–400
2nd gear min
-1
0–1500
Impact rate
1st gear min
-1 0–6000
2nd gear min
-1 0–22500
Max torque Nm 30
Chuck capacity mm 10
Maximum drilling capacity
Wood mm 20
Brickwork
mm 8
Metal mm 10
Weight(without battery)
kg
0.83
Charger SC101
Input Voltage V
AC
220-240
Input
Current
A
0.3
Output Voltage V
DC
12
Output Current(DC) A1.5
Approx. charge time min 80(2.0Ah)
Battery SB10D
Voltage V
DC
10.8V (12V Max)
Capacity Ah 2.0
Type Li-Ion
15
简体中文
ENGLISH (Original Instructions)
4
设计用途
Stanley SCH10 12 伏 Max 锂离子冲击钻设计用
于轻型紧固和钻孔用途。
安全说明
电动工具通用安全警告
@
警告！阅读随电动工具提供的所有安全
警告、说明、图示和规定。不遵照以下所
列说明会导致电击、着火和／或严重伤
害。
保存所有警告和说明书以备查阅。
警告中的术语“电动工具”指市电驱动（有线）电动
工具或电池驱动（无线）电动工具。
a)工作场地的安全
1) 保持工作场地清洁和明亮。 杂乱和黑暗的场地
会引发事故。
2) 不要在易爆环境，如有易燃液体、气体或粉尘的
环境下操作电动工具。 电动工具产生的火花会
点燃粉尘或气体。
3) 操作电动工具时，远离儿童和旁观者。 注意力
不集中会使你失去对工具的控制。
b) 电气安全
1) 电动工具插头必须与插座相配。 绝不能以任何
方式改装插头。 需接地的电动工具不能使用任
何转换插头。 未经改装的插头和相配的插座将
降低电击风险。
2) 避免人体接触接地表面，如管道、散热片和冰
箱 。 如果你身体接触接地表面会增加电击风险。
3) 不得将电动工具暴露在雨中或潮湿环境中。 水
进入电动工具将增加电击风险。
4) 不得滥用软线。绝不能用软线搬运、拉动电动工
具或拔出其插头。 使软线远离热源、油、锐边或
运动部件。 受损或缠绕的软线会增加电击风险。
5) 当在户外使用电动工具时，使用适合户外使用的
延长线。 适合户外使用的电线将降低电击风险。
6) 如果无法避免在潮湿环境中操作电动工具，应
使用带有剩余电流装置（RCD）保护的电源。
RCD的使用可降低电击风险。
c)人身安全
1) 保持警觉，当操作电动工具时关注所从事的操
作并保持清醒。 当你感到疲倦，或在有药物、酒
精或治疗反应时，不要操作电动工具。 在操作
电动工具时瞬间的疏忽会导致严重人身伤害。
2) 使用个人防护装置。 始终佩戴护目镜。 防护装
置，诸如适当条件下使用防尘面具、防滑安全
鞋、安全帽、听力防护等装置能减少人身伤害。
3) 防止意外起动。 在连接电源和/或电池包、拿起
或搬运工具前确保开关处于关断位置。 手指放
在开关上搬运工具或开关处于接通时通电会
导致危险。
4) 在电动工具接通之前，拿掉所有调节钥匙或扳
手 。 遗留在电动工具旋转零件上的扳手或钥匙
会导致人身伤害。
5) 手不要过分伸展。 时刻注意立足点和身体平衡。
这样能在意外情况下能更好地控制住电动工
具。
6) 着装适当。 不要穿宽松衣服或佩戴饰品。 让你
的头发和衣服远离运动部件。 宽松衣服、佩饰
或长发可能会卷入运动部件。
7) 如果提供了与排屑、集尘设备连接用的装置，
要确保其连接完好且使用得当。 使用集尘装置
可降低尘屑引起的危险。
8) 不要因为频繁使用工具而产生的熟悉感而掉
以轻心，忽视工具的安全准则。 某个粗心的动
作可能在瞬间导致严重的伤害。
d) 电动工具使用和注意事项
1) 不要勉强使用电动工具，根据用途使用合适的
电动工具。 选用合适的按照额定值设计的电动
工具会使你工作更有效、更安全。
2) 如果开关不能接通或关断电源，则不能使用该
电动工具。 不能通过开关来控制的电动工具是
危险的且必须进行修理。
3) 在进行任何调节、更换附件或贮存电动工具之
前，必须从电源上拔掉插头和/或卸下电池包（
如可拆卸）。 这种防护性的安全措施降低了电
动工具意外起动的风险。
4) 将闲置不用的电动工具贮存在儿童所及范围
之外，并且不允许不熟悉电动工具和不了解这
些说明的人操作电动工具。 电动工具在未经培
训的使用者手中是危险的。
5) 维护电动工具及其附件。 检查运动部件是否调
整到位或卡住，检查零件破损情况和影响电动
工具运行的其他状况。 如有损坏，应在使用前
修理好电动工具。 许多事故是由维护不良的电
动工具引发的。
6) 保持切削刀具锋利和清洁。 维护良好地有锋利
切削刃的刀具不易卡住而且容易控制。
7) 按照使用说明书，并考虑作业条件和要进行的
作业来选择电动工具、附件和工具的刀头等。
将电动工具用于那些与其用途不符的操作可
能会导致危险情况。
8) 保持手柄和握持表面干燥、清洁，不得沾有油
脂。 在意外的情况下，湿滑的手柄不能保证握
持的安全和对工具的控制。
e) 电池式工具使用和注意事项：
1) 仅使用生产者规定的充电器充电。 将适用于某
种电池包的充电器用到其他电池包时可能会
16
简体中文
5
ENGLISH (Original Instructions)
发生着火危险。
2) 仅使用配有专用电池包的电动工具。 使用其他
电池包可能会产生伤害和着火危险。
3) 当电池包不用时，将它远离其他金属物体，例如
回形针、硬币、钥匙、钉子、螺钉或其他小金属物
体，以防电池包一端与另一端连接。 电池组端
部短路可能会引起燃烧或着火。
4) 在滥用条件下，液体可能会从电池组中溅出，应
避免接触。如果意外碰到液体，用水冲洗。如果
液体碰到了眼睛，还应寻求医疗帮助。 从电池
中溅出的液体可能会发生腐蚀或燃烧。
5) 不要使用损坏或改装过的电池包或工具。 损坏
或改装过的电池组可能呈现无法预测的结果，
导致着火、爆炸或伤害。
6) 不要将电池包暴露于火或高温中。 电池包暴露
于火或高于130°C的高温中可能导致爆炸。
f) 维修
1) 让专业维修人员使用相同的备件维修电动工
具 。 这将保证所维修的电动工具的安全。
2) 决不能维修损坏的电池包。 电池包仅能由生产
者或其授权的维修服务商进行维修。
电钻专用警告语
• 带耳罩进行冲击作业。 暴露于噪声环境会导致
失聪。
• 工具使用前应得到适当支撑。 由于工具输出
转矩大，运行时没有适当支撑会失控导致人
身伤害。
• 当在钻削附件可能触及暗线的场合进行操作
时，通过绝缘握持面握持工具。 钻削附件碰到
带电导线会使工具外露金属零件带电而使操
作者遭受电击。
• 对于搅拌器，除非搅拌装置位于搅拌材料中，
否则不要开启和关闭工具。不这样操作会导致
失控而产生人身伤害。
使用长钻头时的安全说明
• 切勿以高于钻头额定最大转速的速度操作。在
较高的速度下，如果允许钻头在不接触工件的
情况下自由旋转，则很可能发生弯曲，从而导
致人身伤害。
• 始终以低速启动钻孔，钻头尖端与工件接触。
在较高的速度下，如果允许钻头在不接触工件
的情况下自由旋转，则很可能发生弯曲，从而
导致人身伤害。
• 只在与钻头垂直的方向上施加压力，不要施加
过大的压力。钻头可能弯曲导致断裂或失去控
制，从而导致人身伤害。
其他风险
尽管遵守了相关的安全法规并采用了安全装备，某
些其他风险仍然是无法避免的。
这些风险包括：
‒ 听力损伤。
‒ 飞溅颗粒造成的人身伤害风险。
‒ 使用时配件发热导致的灼伤风险。
‒ 长时间使用引起的人身伤害风险。
工具上的标签
您的工具上可能包含下列符号：
: 警告！ 为降低伤害风险，用户必须阅读
说明手册。
请勿直视工作灯。
日期码的位置
包含制造年份的日期码印在工具机壳内。
示例:
2022 XX JN
制造年份
针对所有电池充电器的重要安全说明
请妥善保管好这些说明： 本手册包含重要的
SC101 电池充电器安全和操作说明。
• 在使用充电器之前，请先阅读所有指示以及充
电器、电池组和使用电池组的产品上的警示标
记。
警告：触电危险。请勿让任何液体渗入
充电器。否则可能会引起触电。
警示：灼伤危险。为降低人身伤害风
险，请仅使用 STANLEY 充电式电池充
电。使用其他类型的电池可能会引起
爆裂，并导致人身伤害和损害。
警示：应看管好儿童，以确保他们不将
此设备当做玩具来玩。
注意：在某些情况下，充电器连接到电
源时，充电器触头可能会被异物导致
短路。导电的异物，包括但不限于研磨
粉尘、金属屑、钢丝绒、铝箔纸或任何
由金属粒子组成的物件，必须远离充
电器范围。充电器内没有电池组时，请
务必断开充电器与电源的连接。清洗
前，请务必拔掉充电器。
• 本工具不供身体、感官或智力能力较弱或缺乏
经验和知识的人(包括儿童)使用，除非他们已
由负责其安全的人就使用工具给予监督或指
导。应看管好儿童，以确保他们不将此工具当
做玩具来玩。
17
简体中文
ENGLISH (Original Instructions)
6
• 请勿试图使用本手册指定的充电器以外的其
他任何充电器为电池组充电。充电器和电池组
都是专门设计的，互相配合使用。
• 这些充电器不可用于除为 STANLEY 充电电池
充电以外的用途。 否则可能会导致火灾、触电
或电击。
• 请勿将充电器暴露于雨中或雪中。
• 断开充电器连接时，应拔下插头，切勿拉拽电
源线。这将降低对电插头和电线的损害风险。
• 请确保电源线布置在不易踩踏、踢绊、拉扯或
会受到损害或压力的位置。
• 除非绝对必要，否则请勿使用延长线。 使用不
正确的延长线可能导致火灾、触电或电击的风
险。
• 请勿将任何物件放在充电器上面，或是把充电
器放在可能会堵住通风槽的柔软表面，导致充
电器的内部过热。 请把充电器放置在远离任何
热源的位置。充电器外壳顶端和底端具有通风
槽。
• 请勿使用电源线或插头已损坏的充电器。 请立
即更换已损坏的充电器。
• 如果充电器受到强烈重击、掉落或出现其他损
坏情况，请勿使用充电器。 请将损坏的充电器
送到授权维修中心维修。
• 请勿自行拆卸充电器。需要维护或修理时，请
拿到授权维修中心。 重装不正确可能导致触
电、电击或火灾风险。
• 必须立即将已损坏的电源线交由制造商、服务
代理或类似的合格人员进行更换以防止安全
隐患。
• 清洁前，请先断开充电器和插座的连接，以降
低触电风险。取出电池组不会降低触电风险。
• 切勿将两个充电器连接在一起。
• 充电器额定电压是标准家用电压。请勿试图在
任何其他电压下使用充电器。 此规则不适用于
车载充电器。
电池
• 切勿以任何理由尝试打开。
• 不要将电池暴露在水中。
• 请勿存放在温度可能超过 40 °C 的地方。
• 仅在环境温度介于 10 °C 和 40 °C 之间时充电。
• 只能使用随工具提供的充电器充电。
• 处理电池时，请遵循“保护环境”部分中的说明。
充电器
• 仅使用您的 STANLEY 充电器为随附工具中的电
池充电。 其他电池可能会爆裂，造成人身伤害
和损坏。
• 切勿尝试为不可充电电池充电。
• 立即更换有缺陷的电源线。
• 不要将充电器暴露在水中。
• 不要打开充电器。
• 不要探测充电器。
请妥善保管好这些说明
充电器
SC101 充电器接受12 伏 Max锂离子电池。
这些充电器无需做出任何调整，专为简易操作而
设计。
充电程序（图B）
1. 插入电池组前，请先将充电器 (10) 的插头插入
相应的电源插座上。
2. 请将电池组 (7) 插入充电器中。红色（充电中）
指示灯将不断闪烁，表示充电过程已经开始。
3. 红色灯持续亮起表示充电完成。此时电池组已
完全充电，您可以使用电池组或将电池组留在
充电器上。
注：为了确保锂离子电池的效能和使用寿命最大
化，在首次使用电池组之前必须将其完全充电。
充电过程
有关电池组的充电状态，请参阅下表。
SC101
热/冷电池组延迟
SC101
当充电器检测到电池太热或太冷时，它会自动启动
热/冷电池组延迟，如“充电过程”所示，暂停充电，
直到电池达到合适的温度。然后充电器自动切换到
电池组充电模式。该功能确保了最大的电池寿命。
如果电子保护系统启动，该工具将自动关闭。如果
发生这种情况，将锂离子电池放在充电器上，直到
充满电。
仅限锂离子电池组
锂离子电池具有“电子保护系统”设计，可保护电池
免受过载、过热或过度放电之害。
如果电子保护系统处于运作状态，该工具将自动停
止操作。如果发生这种情况，请将锂离子电池放在
充电器上，直到其完全充电为止。
18
简体中文
7
ENGLISH (Original Instructions)
针对所有电池组的重要安全说明
在订购替换电池组时，请务必提供产品目录号和
电压。
包装箱内的电池组并未完全充电。使用电池组和
充电器之前，请阅读下列安全说明，然后遵循所述
的充电程序。
请阅读所有说明
• 请勿在易爆环境，如有易燃液体、气体或粉尘
的环境中充电或使用电池。 在充电器中插入
或取出电池时可能会点燃粉尘或气体。
• 切勿强行将电池插入充电器。请勿以任何方式
改装电池组并将电池组插入不兼容的充电器，
这可能会导致电池组破裂，造成严重的人身伤
害。
• 只使用 STANLEY 充电器为电池组充电。
• 请勿喷溅电池组或将其浸泡在水或其他液体
中。
• 请勿在温度可能达到或超过 40 ℃ (105 ℉）
的地方（如夏天户外的棚子或金属建筑物中）
存储或使用工具和电池组。
警告：切勿以任何理由试图打开电池
组。电池组外壳破裂或损坏时，请勿将
电池组插入充电器。请勿挤压、掉落或
损坏电池组。请勿使用受过强烈重击、
掉落、碾压或以任何其他方式（如被钉
子穿破、受到锤子的重击、踩踏）受损
的电池组或充电器。否则可能会引起
电击或触电。 应把受损的电池组送返
维修中心进行回收。
警示：不用时，请将工具侧放在平稳的
表面上，以确保不会有踢绊或掉落的
危险。一些具有大型电池组的工具将
直立于电池组之上，但可能会轻易被
撞倒。
锂离子的附加安全说明
（锂离子）
• 即使电池组严重受损或完全损坏，也请勿焚化
电池组。 电池组在火中会发生爆炸。锂离子电
池组在燃烧时会释放有毒气体和物质。
• 如果电池液体接触到皮肤，请立即以中性肥皂
和清水冲洗接触的地方。如果电池液体不慎进
入眼睛，应睁开眼睛并用清水冲洗至少 15 分
钟或直到刺激感缓解。如果需要医疗救助，请
告知医护人员。电池电解质由液状有机碳酸盐
和锂盐的混合物组成。
• 已打开电池的内部物质可能会导致呼吸道刺
激。 请保持空气流通。如果症状持续存在，请
寻求医疗帮助。
警告：灼伤危险。电池液如果接触到火
花或火焰可能会燃烧。
运输
STANLEY 电池符合所有适用的行业和法律标
准规定的运输规范，包括《联合国危险品运输建
议规章范本》(UN Recommendations on the
Transport of Dangerous Goods)、《国际航空运
输协会 (IATA) 危险品规则》(International Air
Transport Association (IATA) Dangerous Goods
Regulations)、《国际海运危险品 (IMDG) 规则》
(International Maritime Dangerous Goods
(IMDG) Regulations) 和《欧洲危险货物国际公路运
输协定》(European Agreement Concerning The
International Carriage of Dangerous Goods by
Road) (ADR)。锂离子电池和电池组已遵循《联合国
危险品运输建议规章范本手册》第 38.3 节关于测试
和标准的说明通过测试。
大多数情况下，发运 STANLEY 电池组不属于完全
管制的 9 类危险品。纳入 9 类危险品发运的情况通
常有两种：
1. 空运两个以上 STANLEY 锂离子电池组，且包
装中只包含电池组（没有工具）；和
2. 包含一个能源等级大于 100 瓦时 (Wh) 的锂离
子电池的任何形式运输。所有锂离子电池外壳
上均标注有瓦时等级。
无论发运是否纳入完全管制范围内，运输公司均
有责任遵循最新法规中关于包装、标签/标记和单
据的要求。
电池运输途中，如果电池两极意外接触导电材料，
可能会引发火灾。运输电池时，请务必保护电池两
极，确保与可能接触电池导致短路的材料良好绝
缘。
本手册本节的信息是出于善意提供，且认为在编制
文档时准确无误。但是不提供明示或暗示的担保。
购买方负有确保其行为遵守适用法规的责任。
电池组
电池类型
SCH10 使用 12 伏 Max 电池组操作。
存储建议
1. 最好将电池存放在阴凉、干燥、远离阳光直射、
不会过热或过冷的地方。为了获得最佳的电池
性能和使用寿命，请您在不使用电池组时将其
存储在室温下。
2. 长期存储时，建议将完全充电的电池组从充电
器取出，存储在阴凉、干燥的地方，以达到最佳
效果。
注：电池组不应在电池已完全耗尽的状态下存放。
使用电池组之前，必须重新为电池组充电。
19
简体中文
ENGLISH (Original Instructions)
8
充电器和电池组上的标签
除了在本手册中所使用的标志，充电器和电池组的
标签还包括：
使用前请阅读说明手册。
充电时间详细信息，请参阅技术参数。
请勿使用导电物体戳刺。
请勿对已损坏的电池组充电。
请勿将其暴露于水中。
应立即更换有缺陷的电线。
请只在10 C 和 40 C 之间的温度下充电
只能在室内使用。
弃置电池组时，请妥善处理以保护我们
的环境。
请只使用 指定的 STANLEY 充电器为
STANLEY 电池组充电。使用 STANLEY
充电器为非 STANLEY 电池充电可能会
导致电池爆炸或出现其他危险情况。
请勿焚化电池组。
包装内的物品
包装内的物品包括：
1 冲击钻
1 充电器
2 电池 (D2) 或 1 电池 (D1)
1 本说明手册
注：N 型号不包括电池组和充电器。
• 检查工具、部件或配件是否在运输过程中损
坏。
• 操作前，请抽空仔细阅读并掌握本手册。
说明（图 A）
SC101
警告：切勿改装本电动工具或其任何部
件，否则可能会导致损坏或人身伤害。
1. 变速触发开关
2. 正/反转按钮
3. 扭矩调节轴环
4. 换档器
5. 无锁匙夹头
6. 电池释放按钮
7. 电池组
8. 工作灯
9. 电量指示灯
10.充电器
11. 功能轴环
设计用途
本冲击钻设计用于轻型紧固和钻孔用途。
请勿在潮湿环境中或在有易燃液体或气体的环境
中使用。
本冲击钻是专业的电动工具。
请勿让儿童接触工具。缺乏经验的操作员需要在监
督下使用本工具。
• 本产品不适合身体、感官或心智能力有缺陷以
及缺乏经验、知识或技能的人员（包括儿童）
使用，除非有相关人员负责他们的安全监督。
请勿在无人监管的情况下让儿童接触本产品。
电气安全
电机只适用一种工作电压。请务必检查电池组的电
压是否和铭牌上的电压一致。另外，请确保充电器
电压和主电源的电压一致。
STANLEY 充电器符合 IEC60335 双重绝
缘要求，因此无需使用接地线。
如果电源线损坏，必须交由 STANLEY 维修部门采
用专门制备的电线进行更换。
使用延长线
除非绝对必要，否则请勿使用延长线。使用适合您
的充电器输入功率的合格延长线（见技术参数）。最
小的导线尺寸为 1 平方毫米；最大长度为 30 米。
使用电缆卷筒时，请务必拉出所有的电缆。
组装与调整
警告：组装与调整之前，请务必取出电
池组。插入或取出电池组之前，请务必
关闭工具。
20
简体中文
9
ENGLISH (Original Instructions)
警告：只使用 STANLEY 电池组和充电
器。
插入和取出
工具上的电池组（图 C）
警告：为了降低严重的人身伤害风险，
调整或拆除/安装附件或配件之前，请
将正/反转控制按钮置于锁止位置，或
关闭工具电源并取出电池组。意外启动
可能会导致人身伤害。
注：请确保您的电池组 (7) 已完全充电。
安装和拆卸电池
•要安装电池(7)，将其与工具上的接口对齐。将电
池滑入接口，并推动，直到电池扣到位。
•要拆卸电池，请按下释放按钮(6)，同时将电池从
接口中拔出。
操作
使用说明
警告：请务必遵守安全指示和适用法
规。
警告：为了降低严重人身伤害的危险，
调整或拆卸/安装附件或配件之前，请
将正/反转控制按钮锁定在关闭位置，
或请务必关闭工具电源，断开电池组。
正确的手持方式（图 A、H）
警告：为降低严重人身伤害的风险，
请务必使用正确的手持方式，如图所
示。
警告：为降低严重人身伤害的风险，
请务必紧握工具以防止意外事件。
正确的手持方式如图所示，一只手要放在主手柄
(9) 上。
变速触发开关（图 A）
要开启工具，请按压触发开关 (1)。要关闭工具，
请松开触发开关。您的工具配备制动器。触发开关
完全释放时夹头将停止运作。
变速开关可让您根据特定用途选择最适用的速度。
按压开关越紧，工具运作越快。为了获得最长的工
具使用寿命，请仅在启动钻孔或紧固件时使用变
速 。
注：不建议在变速范围内连续使用工具，否则可能
会损坏开关，因此应尽量避免。
正/反转控制按钮 （图 A）
正/反转控制按钮 (2) 可确定工具方向，并可作为锁
定按钮使用。
如果要选择正向旋转，请松开触发开关，然后按下工
具右侧的正/反转控制按钮。
如果要选择反向旋转，请按下工具左侧的正/反转控
制按钮。控制按钮的中心位置会将工具锁定在关闭
位置。改变控制按钮的位置时，请确保触发开关处于
松开状态。
注：改变旋转方向后第一次运行工具时，您可能会在
启动时听到“咔哒声”。这是正常现象，并不表示出现
问题。
工作灯（图 A）
工作灯 (8) 位于扭矩调节轴环 (3) 下方。按压触发
开关时，工作灯就会亮起。
注：工作灯用于照亮紧邻的工作表面，不能当做手
电筒使用。
电量指示灯(图A)
该工具包括电量指示灯。当按下触发开关时，LED
灯将显示剩余电量的大致水平。
扭矩调节轴环 （图 A）
将 (11) 转至螺丝标示。 扭矩调节轴环 (
3
) 上清晰标
注了编号和钻头符号。 应旋转轴环直到所需设置位
于工具顶部。 轴环上提供了定位器， 不必靠猜测来选
择紧固扭矩。 轴环上的编号越大， 扭矩越高， 并且可
安装的紧固件也越大。 如果要锁定夹头以进行钻孔
操作， 请将功能轴环 (11) 移至钻头位置。
注： 使用电钻/起子机进行钻孔操作时， 请确保将功
能轴环设置为钻孔图标与工具顶部的中心线对齐。
否则夹头会在您试图钻孔时滑动。
双档调速（图 A、D）
电钻/起子机的双档功能可换档以获得更大的适用
性。
如果要选择低速（高扭矩设置），请关闭工具并让他停
止转动。请将换档器 (4) 尽量向后滑动（滑向夹头）。
如果要选择高速（低扭矩设置），请关闭工具并让他停
止转动。请将换档器尽量向前滑动（远离夹头）。
注：
工具运行时切勿换档。如果无法换挡，请确保双
速换档按钮已完全向前推动或完全向后推动。
无锁匙单套夹头（图 E）
您的工具备有无锁匙夹头，带有一个旋转套管，便于
单手操作夹头。如果要插入钻头或其他配件，请执行
下列步骤。
1. 按照之前的说明将触发开关锁定在关闭位置。
2. 用一只手抓住夹头的黑色套管，用另一只手固定
工具。逆时针旋转套管以插入所需的配件。
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
