DeWalt DCF886 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
DCF836
DCF886
2
English (original instructions) 03
简体中文 13
繁體中文 21
한국어
29
Copyright DeWALT
1
Figure 1
Figure 2
h
i
b
a
g
e
f
g
c
d
g
e
f
k
j
i
l
2
Figure 3
Figure 4
c
d
c
d
ENGLISH
3
BRUSHLESS CORDLESS COMPACT IMPACT DRIVER
DCF836, DCF886
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make
DeWALT one of the most reliable partners for professional power tool users.
Technical Data
DCF836 DCF886
Voltage V
DC
14.4 18
Battery type Li-Ion Li-Ion
No load speed min
-1
0–2800 0–2800
Impact rate min
-1
0–3200 0–3200
Max torque Nm 155 165
Tool holder 6.25 mm (1/4") 6.25 mm (1/4")
Weight (without battery pack) kg 0.94 0.94
Battery pack DCB140 DCB141 DCB142 DCB143
Battery type Li-Ion Li-Ion Li-Ion Li-Ion
Voltage V
DC
14.4 14.4 14.4 14.4
Capacity A
h
3.0 1.5 4.0 2.0
Weight kg 0.53 0.30 0.54 0.30
Battery pack DCB180 DCB181 DCB182 DCB183 DCB184
Battery type Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion
Voltage V
DC
18 18 18 18 18
Capacity A
h
3.0 1.5 4.0 2.0 5.0
Weight kg 0.64 0.35 0.61 0.40 0.62
Charger DCB105
Mains voltage V
AC
220-240
Battery type Li-Ion
Approx. charging time min 30 40 55 70 90
(1.5 Ah (2.0 Ah (3.0 Ah (4.0 Ah (5.0 Ah
battery packs) battery packs) battery packs) battery packs) battery packs)
Weight kg 0.49
Charger DCB115
Mains voltage V
AC
220-240
Battery type Li-Ion
Approx. charging time min 30 40 55 70 90
(1.5 Ah (2.0 Ah (3.0 Ah (4.0 Ah (5.0 Ah
battery packs) battery packs) battery packs) battery packs) battery packs)
Weight kg 0.5
ENGLISH
4
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
ENGLISH
5
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specific Safety Rules for
Impact Drivers
• Hold power tool by insulated gripping
surfaces when performing an operation
where the fastener may contact hidden
wiring. Fasteners contacting a “live” wire may
make exposed metal parts of the power tool
“live” and could give the operator an electric
shock.
Residual Risks
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
Impairment of hearing.
Risk of personal injury due flying particles.
Risk of burns due to accessories becoming hot
during operation.
Risk of personal injury due to prolonged use.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
DATE CODE POSITION
The Date Code, which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
ENGLISH
6
Example:
2013 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating instruc tions
for the DCB105 and DCB115 battery charger.
• Beforeusingthecharger,readallinstructions
and cautionary markings on charger, battery
pack and product using the battery pack.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable battery packs. Other types
of batteries may overheat and burst
resulting in personal injury and property
damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions, with
the charger plugged in to the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminium foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean.
• DONOTattempttochargethebatterypack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• Thesechargersarenotintendedfor
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Donotexposechargertorainorsnow.
• Pullbyplugratherthancordwhen
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Makesurethatcordislocatedsothatitwill
not be stepped on, tripped over or otherwise
subjected to damage or stress.
• Donotuseanextensioncordunlessit
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock or electrocution.
• When operating a charger outdoors, always
provide a dry location and use an extension
cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
• Donotblocktheventilationslotsonthe
charger.Theventilationslotsarelocated
on the top and sides of the charger. Place
the charger in a position away from any heat
source.
• Donotoperatechargerwithdamagedcord
or plug — have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped or otherwise
damaged in any way. Take it to an authorised
service centre.
• Donotdisassemblethecharger;takeitto
an authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
• Incaseofdamagedpowersupplycordthe
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnectthechargerfromtheoutlet
beforeattemptinganycleaning.Thiswill
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVERattempt to connect 2 chargers together.
• Thechargerisdesignedtooperateon
standard220-240Vhouseholdelectrical
power. Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB105 and DCB115 charger accepts 10.8 V,
14.4 V and 18 V Li-Ion (DCB121, DCB123,
DCB140, DCB141, DCB142, DCB143, DCB180,
DCB181, DCB182, DCB183 and DCB184) battery
packs.
This charger requires no adjustment and is designed
to be as easy as possible to operate.
Charging Procedure (fig. 2)
1. Plug the charger into an appropriate 220-240 V
outlet before inserting the battery pack.
ENGLISH
7
2. Insert the battery pack (f) into the charger,
making sure the pack is fully seated in the
charger. The red (charging) light will blink
continuously indicating that the charging
process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, fully charge the pack before first use.
Charging Process
Refer to the table below for the state of charge of
the battery pack.
Charge indicators: DCB105
charging
fully charged
hot/cold pack delay
replace battery pack
Charge indicators: DCB115
charging
fully charged
hot/cold pack delay*
This charger will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing to
light or by displaying problem pack or charger blink
pattern.
NOTE: This could also mean a problem with a
charger.
If the charger indicates a problem, take the charger
and battery pack to be tested at an authorised
service centre.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a hot/cold pack
delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
A cold battery pack will charge at about half the rate
of a warm battery pack. The battery pack will charge
at that slower rate throughout the entire charging
cycle and will not return to maximum charge rate
even if the battery warms.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include the catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below and then follow
the charging procedures outlined.
READ ALL INSTRUCTIONS
• Donotchargeorusethebatterypack
in explosive atmospheres, such as in the
presence of flammable liquids, gases or
dust. Inserting or removing the battery pack
from the charger may ignite the dust or fumes.
• Never force the battery pack into charger.
Do not modify the battery pack in any way
to fit into a non-compatible charger as
battery pack may rupture causing serious
personal injury.
• Chargethebatterypacksonlyindesignated
DeWALT chargers.
• DONOTsplash or immerse in water or other
liquids.
• Donotstoreorusethetoolandbattery
pack in locations where the temperature
may reach or exceed 40˚C (105°F) (such as
outside sheds or metal buildings in summer).
• Forbestresults,makesurethebatterypackis
fully charged before use.
WARNING: Never attempt to open
the battery pack for any reason. If
the battery pack case is cracked or
damaged, do not insert it into the
charger. Do not crush, drop or damage
battery pack. Do not use a battery
pack or charger that has received a
sharp blow, been dropped, run over
or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped
on). Electric shock or electrocution may
result. Damaged battery packs should
be returned to the service centre for
recycling.
ENGLISH
8
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
• Donotincineratethebatterypackevenifit
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium ion battery packs are burned.
• Ifbatterycontentscomeintocontactwith
the skin, immediately wash the area with
mild soap and water. If the battery liquid gets
into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contentsofopenedbatterycellsmaycause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Battery Pack
BATTERY TYPE
The DCF836 operates on 14.4 volt battery packs.
The DCF886 operates on 18 volt battery packs.
The DCB140, DCB141, DCB142, DCB143,
DCB180, DCB181, DCB182, DCB183 or DCB184
battery packs may be used. Refer to Technical
Data for more information.
Storage Recommendations
1. The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
2. For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
Read instruction manual before use.
Battery charging.
Battery charged.
Hot/cold pack delay.
x
Problem pack or charger.
Problem powerline.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Use only with DeWALT battery packs.
Others may burst causing personal injury
and damage.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4°C and 40°C.
Discard the battery pack with due care for
the environment.
Do not incinerate the battery pack.
Charges Li-Ion battery packs.
See Technical Data for charging time.
Only for indoor use.
ENGLISH
9
Package Contents
The package contains:
1 Impact driver
1 Charger
2 Batteries
1 Magnetic bit holder
1 Belt hook
1 Kitbox
1 Instruction manual
NOTE: Battery packs, chargers and kitboxes are not
included with N-models.
• Checkfordamagetothetool,partsor
accessories which may have occurred during
transport.
• Takethetimetothoroughlyreadand
understand this manual prior to operation.
Description (fig. 1, 2)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Trigger switch
b. Forward/reverse button
c. Chuck collar
d. 6.35 mm (1/4") hex quick-release chuck
e. Battery release button
f. Battery pack
g. Worklight
h. Belt hook
i. Screw
j. Magnetic bit holder
k. Main handle
l. Fuel gauge
INTENDED USE
These impact drivers are designed for professional
impact screwdriving applications. The impact
function makes this tool particularly useful for driving
fasteners in wood, metal and concrete.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These impact drivers are professional power tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• Thisproductisnotintendedforusebypersons
(including children) suffering from diminished
physical, sensory or mental abilities, or for lack
of experience and/or for want of knowledge or
skills unless they are supervised by a person
responsible for their safety. Children should
never be left alone to play with this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DeWALT charger is double insulated
in accordance with IEC 60335; therefore
no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DeWALT service organisation.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical Data). The minimum conductor size
is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
WARNING: Use only DeWALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fig. 2)
NOTE: For best results, make sure your battery
pack is fully charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack (f) with the rails inside the
tool’s handle.
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that it does
not disengage.
ENGLISH
10
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the battery release button (e) and firmly
pull the battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some DeWALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (l). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Belt Hook and Bit Clip (fig. 1)
WARNING: To reduce the risk of
serious personal injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook. ONLY hang
tool’s belt hook from a work belt.
WARNING: To reduce the risk of
serious personal injury, ensure the
screw holding the belt hook is secure.
IMPORTANT: When attaching or replacing the
belt hook or bit clip, use only the screw (i) that is
provided. Be sure to securely tighten the screw.
The belt hook (h) and bit clip (j) can be be attached
to either side of the tool using only the screw (i)
provided, to accommodate left- or right-handed
users. If the hook or bit clip is not desired at all, it
can be removed from the tool.
To move belt hook or bit clip, remove the screw
(i) that holds it in place then reassemble on the
opposite side. Be sure to securely tighten the screw.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Proper Hand Position (fig. 1, 4)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (k).
Variable Speed Trigger Switch (fig. 1)
To turn the tool on, squeeze the trigger switch (a). To
turn the tool off, release the trigger switch. Your tool
is equipped with a brake. The chuck will stop when
the trigger switch is fully released.
The variable speed switch enables you to start
the application at a slow speed. The further you
squeeze the trigger, the faster the tool will operate.
For maximum tool life, use variable speed only for
starting holes or fasteners.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(fig. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and depress the forward/reverse control button on
the right side of the tool.
To select reverse, depress the forward/reverse
control button on the left side of the tool. The centre
position of the control button locks the tool in the off
position. When changing the position of the control
button, be sure the trigger is released.
NOTE: The first time the tool is run after changing
the direction of rotation, you may hear a click on
start up. This is normal and does not indicate a
problem.
Worklights (fig. 1)
There are three worklights (g) located around the
chuck collar (c). The worklights will be activated
when the trigger switch is depressed.
ENGLISH
11
When the trigger is released, the worklights will stay
illuminated for up to 20 seconds.
NOTE: The worklights are for lighting the immediate
work surface and are not intended to be used as a
flashlight.
Quick-Release Chuck (fig. 1, 3)
WARNING: Use only impact
accessories. Non-impact accessories
may break and cause a hazardous
condition. Inspect accessory prior to
use to ensure that it con tains no cracks.
NOTE: The chuck accepts 6.35mm (1/4") hex
accessories and 25.4mm (1") bit tips only. Using
25.4mm (1") bits allows better access in tight
spaces.
Place the forward/reverse button (b) in the locked
off (centre) position or remove battery pack before
changing accessories.
To install an accessory, push accessory to fully insert
into chuck. The chuck collar does not need to be
pulled up to lock accessory in place.
To remove an accessory, pull the chuck collar away
from the front of the tool. Remove the accessory
and release the collar.
Usage
Your impact tool generates the following maximum
torque:
Cat # Nm Ft.-Lbs. In.-Lbs.
DCF836 155 117 1400
DCF886 165 125 1500
CAUTION: Ensure fastener and/or
system will withstand the level of torque
generated by the tool. Excessive torque
may cause breakage and possible
personal injury.
1. Place the accessory on the fastener head. Keep
the tool pointed straight at the fastener.
2. Press switch to start operation. Release the
switch to stop operation. Always check torque
with a torque wrench, as the fastening torque is
affected by many factors including the following:
• Voltage: Low voltage, due to a nearly
discharged battery, will reduce fastening
torque.
• Accessory size: Failure to use the correct
accessory size will cause a reduction in
fastening torque.
• Bolt Size: Larger bolt diameters generally
require higher fastening torque. Fastening
torque will also vary according to length,
grade, and torque coefficient.
• Bolt: Ensure that all threads are free of rust
and other debris to allow proper fastening
torque.
• Material: The type of material and surface
finish of the material will affect fastening
torque.
• Fastening Time: Longer fasten ing time
results in increased fastening torque. Using
a longer fastening time than recom mended
could cause the fasteners to be overstressed,
stripped or damaged.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
ENGLISH
12
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DeWALT recommended
accessories should be used with this
product.
WARNING: To reduce the risk of
injury, only use DeWALT impact-ready
accessories.
WARNING: Use only impact
accessories. Non-impact accessories
may break and cause a hazardous
condition. Inspect accessories prior
to use to ensure that they con tain no
cracks.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DeWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DeWALT provides a facility for the collection and
recycling of DeWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DeWALT office at the address indicated in this
manual. Alternatively, a list of authorised DeWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Runthebatterypackdowncompletely,then
remove it from the tool.
• Li-Ioncellsarerecyclable.Takethemtoyour
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
中文简体
13
18V 锂电充电式无刷磁浮冲击起子
DCF836DCF886
恭喜!
感谢您选购 DEWALT 工具。凭借多年的产品开发和创新经验,DEWALT 已经成为专业电动工具用户最可
靠的合作伙伴之一。
技术参数
DCF836 DCF886
电压 伏特 14.4 18
电池类型 锂离子 锂离子
空载速度 / 0–2800 0–2800
冲击率 / 0–3200 0–3200
最大扭矩 牛米 155 165
工具夹持器 6.25 毫米 (1/4") 6.25 毫米 (1/4")
重量(不含电池组) 千克 0.94 0.94
电池组 DCB140 DCB141 DCB142 DCB143
电池类型 锂离子 锂离子 锂离子 锂离子
电压 伏特 14.4 14.4 14.4 14.4
电池容量 安培 3.0 1.5 4.0 2.0
重量 千克 0.53 0.30 0.54 0.30
电池组 DCB180 DCB181 DCB182 DCB183 DCB184
电池类型 锂离子 锂离子 锂离子 锂离子 锂离子
电压 伏特 18 18 18 18 18
电池容量 安培 3.0 1.5 4.0 2.0 5.0
重量 千克 0.64 0.35 0.61 0.40 0.62
充电器 DCB105
电源电压 伏特 220
电池类型 锂离子
大约充电时间 分钟 30 40 55 70 90
(1.5 Ah 2.0 Ah 3.0 Ah 4.0 Ah 5.0 Ah
电池组) 电池组) 电池组) 电池组) 电池组)
重量 千克 0.49
充电器 DCB115
电源电压 伏特 220
电池类型 锂离子
大约充电时间 分钟 30 40 55 70 90
(1.5 Ah 2.0 Ah 3.0 Ah 4.0 Ah 5.0 Ah
电池组) 电池组) 电池组) 电池组) 电池组)
重量 千克 0.5
中文简体
14
定义:安全指引
下列定义描述了各警示词的严重程度。请仔细阅读
本手册,并注意这些警示符号。
危险:表示存在紧急危险情况,如果不
加以避免,导致死亡或严重伤害
警告:表示存在潜在的危险情况,如果
不加以避免,可能导致死亡或严重伤
警示:表示存在潜在危险情况,如果不
加以避免,可能导致轻度或中度伤害
注意:表示存在不涉及人身伤害的情
况,如果不加以避免,可能导致财产
损失
表示存在触电风险。
表示存在火灾风险。
警告:为降低伤害风险,请阅读使用手
册。
电动工具通用安全警告
警告!阅读所有警告和所有说明。不遵
照以下警告和说明会导致电击、着火
和/或严重伤害。
保存所有警告和说明书以备查阅。
在所有下列的警告中术语“电动工具”指市电驱动
(有线)电动工具或电池驱动(无线)电动工具。
1) 工作场地的安全
a) 保持工作场地清洁和明亮。混乱和黑暗的场
地会引发事故。
b) 不要在易爆环境,如有易燃液体、气体或粉
尘的环境下操作电动工具。电动工具产生的
火花会点燃粉尘或气体。
c) 让儿童和旁观者离开后操作电动工具。注意
力不集中会使你失去对工具的控制。
2) 电气安全
a) 电动工具插头必须与插座相配。绝不能以任
何方式改装插头。需接地的电动工具不能使
用任何转换插头。未经改装的插头和相配的
插座将减少电击危险。
b) 避免人体接触接地表面,如管道、散热片和
冰箱。如果你身体接地会增加电击危险。
c) 不得将电动工具暴露在雨中或潮湿环境中。
水进入电动工具将增加电击危险。
d) 不得滥用电线。绝不能用电线搬运、拉动电
动工具或拔出其插头。使电线远离热源、
油、锐边或运动部件。受损或缠绕的软线会
增加电击危险。
e) 当在户外使用电动工具时,使用适合户外使
用的外接软线。适合户外使用的软线将减少
电击危险。
f) 如果在潮湿环境下操作电动工具是不可避免
的,应使用剩余电流动作保护器(RCD)。
使用RCD可减小电击危险。
3) 人身安全
a) 保持警觉,当操作电动工具时关注所从事的
操作并保持清醒。当你感到疲倦,或在有药
物、酒精或治疗反应时,不要操作电动工
具。在操作电动工具时瞬间的疏忽会导致严
重人身伤害。
b) 使用个人防护装置。始终佩戴护目镜。安全
装置,诸如适当条件下使用防尘面具、防滑
安全鞋、安全帽、听力防护等装置能减少人
身伤害。
c) 防止意外起动。确保开关在连接电源和/或电
池盒、拿起或搬运工具时处于关断位置。
指放在已接通电源的开关上或开关处于接通
时插入插头可能会导致危险。
d) 在电动工具接通之前,拿掉所有调节钥匙或
扳手。遗留在电动工具旋转零件上的扳手或
钥匙会导致人身伤害。
e) 手不要伸展得太长。时刻注意立足点和身体
平衡。这样在意外情况下能很好地控制电动
工具。
f) 着装适当。不要穿宽松衣服或佩戴饰品。让
你的衣服、手套和头发远离运动部件。宽松
衣服、佩饰或长发可能会卷入运动部件中。
g) 如果提供了与排屑、集尘设备连接用的装
置,要确保他们连接完好且使用得当。使用
这些装置可减少尘屑引起的危险。
4) 电动工具使用和注意事项
a) 不要滥用电动工具,根据用途使用适当的电
动工具。选用适当设计的电动工具会使你工
作更有效、更安全。
b) 如果开关不能接通或关断工具电源,则不能
使用该电动工具。不能用开关来控制的电动
工具是危险的且必须进行修理。
c) 在进行任何调节、更换附件或贮存电动工具
之前,必须从电源上拔掉插头和/或使电池
盒与工具脱开。这种防护性措施将减少工具
意外起动的危险。
d) 将闲置不用的电动工具贮存在儿童所及范围
之外,并且不要让不熟悉电动工具或对这些
说明不了解的人操作电动工具。电动工具在
未经培训的用户手中是危险的。
e) 保养电动工具。检查运动件是否调整到位或
卡住,检查零件破损情况和影响电动工具运
行的其他状况。如有损坏,电动工具应在使
用前修理好。许多事故由维护不良的电动工
具引发。
f) 保持切削刀具锋利和清洁。保养良好的有锋
利切削刃的刀具不易卡住而且容易控制。
g) 按照使用说明书,考虑作业条件和进行的作
业来使用电动工具、附件和工具的刀头等。
将电动工具用于那些与其用途不符的操作可
能会导致危险。
中文简体
15
5) 电池式工具使用和注意事项:
a) 只用制造商规定的充电器充电。将适用于某
种电池盒的充电器用到其他电池盒时会发生
着火危险。
b) 只有在配有专用电池盒的情况下才使用电动
工具。使用其他电池盒会发生损坏和着火危
险。
c) 当电池盒不用时,将它远离其他金属物体,
例如回形针、硬币、钥匙、钉子、螺钉或其
他小金属物体,以防一端与另一端连接。
池端部短路会引起燃烧或火灾。
d) 在滥用条件下,液体会从电池中溅出,避免
接触。如果意外碰到了,用水冲洗。如果液
体碰到了眼睛,还要寻求医疗帮助。从电池
中溅出的液体会发生腐蚀或燃烧。
6) 维修
a) 让专业维修人员使用相同的备件维修电动工
具。这将保证所维修的电动工具的安全。
附加安全说明
在紧固件可能触及暗线或自身软线之处进行操
作时,要通过绝缘握持面来握持工具。紧固件
碰到带电导线会使工具外露的金属零件带电从
而使操作者受到电击。
剩余风险
尽管遵守了相关的安全法规并采用了安全装备,某
些剩余风险仍然是无法避免的。这些风险包括:
听力损伤。
飞散颗粒造成的人身伤害风险。
操作过程中配件加热而产生的烧伤危险。
长时间使用引起的人身伤害风险。
工具上的标记
工具上印有下列标志:
使用前请阅读使用手册。
日期代码位置
连接工具和电池之间的外壳表面印有日期代码,
期代码包括制造年份。
例如:
2013 XX XX
制造年份
针对所有电池充电器的重要安全
说明
请妥善保管好这些说明:本手册包含重要的 DCB105
DCB115电池充电器安全和操作说明。
使用充电器之前,请阅读所有说明和充电器、
电池组以及电池组产品上的警示标记。
警告:触电危险。请勿让任何液体渗入
充电器,否则会引起触电。
注意:灼伤危险。为降低受伤风险,只
使用 DEWALT 充电式电池组充电。其
他类型的电池可能会过热爆裂,并造成
人身伤害和财产损失。
警示: 必须监督儿童,确保他们不将此
设备当做玩具来玩。
注意:在某些情况下,充电器连接电源
时,异物可能会连接充电器内的外露充
电接触点而造成短路。带有导电性质的
外来物件,包括但不限于,例如钢材、
木材、铝箔或任何金属颗粒堆积物等都
不应出现在充电器内。充电器内没有电
池组时,请断开充电器与电源的连接。
清洗前,务必拔掉充电器。
请勿使用本手册指定的充电器以外的其他任何
充电器为电池组充电。充电器和电池组都是专
门设计的,互相配合使用。
除了为 DEWALT 充电式电池充电以外,这些充
电器都不能用于其他任何用途。否则,可能会
导致火灾、触电或电击。
请勿将充电器暴露于雨中或雪中。
断开充电器时应拔下插头,切勿拉拽电线。
将减少电源插头和电源线损坏的风险。
确保电源线布置在不易踩踏、踢绊、拉扯或会
受到损坏或压力的位置
非绝对必要条件下禁止使用延长线。使用延长
线不当可能会导致火灾、触电或电击的危险。
户外操作充电器时,要保持干燥,使用适合户
外使用的延长线。采用适合户外使用的电线可
降低触电风险。
不得堵塞充电器上的通风槽。通风槽位于充电
器的顶部和两侧。请把充电器放置在远离任何
热源的地方。
禁止使用电源线或插头已损坏的充电器 请立
即更换已损坏的充电器。
如果充电器受到强烈重击、掉落或出现其他损
坏情况,请不要使用充电器。 请将损坏的充电
器送到授权维修中心维修。
请勿拆卸充电器,请将需要维修或修理的充电
器送到授权维修中心。重装不正确可能会导致
触电、电击或火灾的危险。
必须立即将已损坏的电源线交由制造商、服务
代理或类似的合格人员进行更换以防止安全隐
患。
清洁前,请先断开充电器和插座的连接,以降
低触电风险。取出电池组不会可降低触电风
险。
切勿尝试将两个充电器连接在一起。
充电器额定电压是标准 220 伏特家用电压。请
勿在任何其他电压下使用充电器。此规则不适
中文简体
16
用于车载充电器。
请妥善保管好这些说明
充电器
DCB105 DCB115充电器适用于 10.8V14.4V
18V 锂离子(DCB121DCB123DCB140
DCB141DCB142DCB143DCB180
DCB181DCB182DCB183 DCB184)电池
组。
此充电器专为简易操作而设计,因此无需做出任何
调整。
充电程序(图 2
1. 插入电池组前请将充电器插入到相应的 220V
插座。
2. 将电池组 (f) 插入到充电器中,确保电池组完全
就位。红色(充电中)指示灯将不断闪烁,表
示充电过程已经开始。
3. 红色灯持续亮起表示充电完成。此时电池组已
完全充电,您可以使用电池组或将电池组留在
充电器上。
注:为了确保锂离子电池的效能和使用寿命最大
化,在首次使用电池组之前必须将其完全充电。
充电过程
关于电池组的充电状态,请参阅下表。
充电状态:DCB105
充电中 –– –– –– ––
已完全充电 –––––––––––––––––
/冷电池组延迟 –– • –– • –– • –– •
x
电池组或充电器故障 • • • • • • • • • • • •
电源线故障 •• •• •• •• •• ••
充电状态:DCB115
充电中
已完全充电
/冷电池组延迟*
此充电器不能为故障的电池组充电。充电器指示灯
不亮或“故障的电池组或充电器”指示灯闪烁时,
表示电池有故障。
注:这也可能意味充电器有故障。
如果充电器提示存在故障,请将充电器和电池组送
到授权维修中心进行测试。
/冷电池组延迟
当充电器检测到电池过热或过冷时,它会自动启动
/冷电池延迟模式,暂停充电,直到电池达到适当
的温度。然后,充电器会自动切换到电池组充电模
式。此功能可确保电池拥有最长的使用寿命。
XR 锂离子电池工具具有“电子保护系统”设计,
可保护电池免受过载、过热或过度放电之害。
如果电子保护系统处于运作状态,该工具将自动停
止操作。如果发生这种情况,请将锂离子电池放在
充电器上直到完全充电。
冷电池组充电速度约为热电池组充电速度的一半。
电池组在整个充电周期的充电速度都会较慢,即使
电池升温也不会恢复到最大速度。
针对所有电池组的重要安全说明
在订购更换电池组时,请务必附上目录号码和电
压。
包装箱内的电池组并未完全充电。在使用电池组和
充电器之前,请阅读下面的安全说明,然后按照所
述充电程序进行操作。
请阅读所有说明
请勿在易爆环境中充电或使用电池组,如有易
燃液体、气体或粉尘的环境。在充电器中插入
或取出电池组时可能会点燃粉尘或烟雾。
切勿将电池组强行插入充电器。不得以任何方
式改装电池组并将电池组插入不兼容的充电
器,这种操作可能会导致电池组破裂,并造成
严重的人身伤害。
只使用指定的 DEWALT 充电器为电池组充电。
请勿喷溅电池组或将其浸泡在水或其他液体
中。
禁止在温度可能达到或超过 40°C105°F
的地方(如夏天户外的棚子或金属建筑物中)
存放或使用工具和电池组。
为达到最佳效果,请确保电池组在使用前已完
全充电。
警告:切勿以任何理由试图打开电池
组。电池组外壳破裂或损坏时,不要将
电池组插入充电器。不要挤压、掉落或
损坏电池组。不要使用受过强烈重击、
掉落、碾压或以任何其他方式(如被钉
子穿破、受到锤子的重击、踩踏)受损
的电池组或充电器,否则可能会引起触
电或电击。损坏的电池组应交回维修中
心进行回收。
注意:不用时,将工具侧放在平稳的表
面上,确保不会有踢绊或掉落的危险。
一些具有大型电池组的工具将直立于电
池组之上,但可能会轻易被撞倒。
中文简体
17
锂离子电池的安全说明
即使电池组已经严重受损或已完全耗竭也不可
焚烧处理电池组。电池组会在火中会发生爆
炸。锂离子电池组在燃烧时会释放有毒气体和
物质。
如果皮肤接触到电池内含物质,请立即用温和
肥皂和水冲洗接触的地方。如果电池液进入眼
睛,应睁开眼睛用清水冲洗至少 15 分钟或直
到刺激感消失。如果需要医疗救助,请告知医
护人员。电池电解质是由液状有机碳酸盐和锂
盐的混合物组成。
已打开电池的内部物质可能会导致呼吸道刺
激。请保持空气流通。如果症状持续存在,请
寻求医疗帮助。
警告:灼伤危险。电池液如果接触到火
花或火焰就有可能会燃烧。
电池组
电池类型
DCF836 使用 14.4 伏特电池组。
DCF886 使用 18 伏特电池组。
DCB140DCB141DCB142DCB143DCB180
DCB181DCB182DCB183 DCB184 电池组
都可以使用。更多信息,请参阅技术参数
存放建议
1. 最好将电池存放在阴凉、干燥、远离阳光直
射、不会过热或过冷的地方。为了获得最佳的
电池性能和使用寿命,请您在不使用电池组时
将其存储在室温下。
2. 长期存储时,建议将完全充电的电池组从充电
器取出,存储在阴凉、干燥的地方,以达到最
佳效果。
注:电池组不应在电池已完全耗尽的状态下存放。
使用电池组之前,必须重新为电池组充电。
充电器和电池组上的标签
除了在本手册中所使用的标志,充电器和电池组的
标签还包括:
使用前请阅读使用手册。
电池充电中。
电池完成充电。
/冷电池组延迟。
x
电池组或充电器故障。
电源线故障。
请勿使用导电物体碰触。
请勿对已损坏的电池组充电。
只使用 DEWALT 电池组。其他电池组可
能会爆炸,并造成人身伤害和损害。
请勿将其暴露于水中。
电线故障,请立即更换。
只在 4°C 40°C 之间的温度下充电。
弃置电池组时,请妥善处理以保护我们
的环境。
请勿焚烧电池组。
锂离子电池组充电。
有关充电时间,请参阅技术参数
只能在室内使用。
包装内容
本产品包装内的物品有:
1 冲击起子
1 充电器
2 电池
1 磁力钻头夹持器
1 皮带扣
1 工具箱
1 使用手册
N 型号不包括电池组、充电器和工具箱。
检查工具、部件或配件是否在运输过程中损
坏。
操作前,请抽空仔细阅读并掌握本手册。
中文简体
18
说明(图 12
警告:切勿改装电动工具或其任何部
件,否则可能会导致损坏或人身伤害。
a. 触发开关
b. 正转/反转按钮
c. 夹具环
d. 6.35 mm (1/4") 六角快速释放夹头
e. 电池释放按钮
f. 电池组
g. 工作灯
h. 皮带扣
i. 螺钉
j. 磁力钻头夹持器
k. 主手柄
l. 电量计
设计用途
这些冲击起子是为专业冲击起子操作而设计的。冲
击功能使这个工具非常有用,特别是在木材、金属
和混凝土中钻紧固件这方面。
请勿在潮湿环境中或在有易燃液体或气体的环境中
使用。
这些冲击起子是专业型电动工具。请勿让儿童接触
工具。缺乏经验的操作员需要在监督下使用此工
具。
本产品不适合身体、感官或心智能力有缺陷以
及缺乏经验、知识或技能的人员(包括儿童)
使用,除非有相关人员负责他们的安全监督。
请勿在无人监管的情况下让儿童接触本产品。
电器安全
电机只适用一种工作电压。请务必检查电池组的电
压是否和铭牌上的电压一致。另外,请确保充电器
电压和主电源的电压一致。
您的 DEWALT 充电器符合 IEC 60335
重绝缘要求,因此无需使用接地线。
若电源线损坏,必须交由 DEWALT 服务部门采用专
门制备的电线进行更换。
使用延长电缆
除非绝对必要,否则请勿使用延长线。使用适合您
的充电器电源输入的合格延长线(见技术参数)。
最小的导线尺寸为 1mm
2
;最大长度为 30 m
使用电缆卷筒时,请务必拉出所有的电缆。
组装和调整
警告:为了减少严重人身伤害的危险,
调整或拆卸/安装附件或配件之前,
请将正转/反转控制按钮锁定在关闭位
置,或请务必关闭工具电源,断开电池
组。意外启动可能会导致人身伤害。
警告:只使用 DEWALT 电池组和充电
器。
插入和拆除电池组(图 2
注:为达到最佳效果,请确保电池组在使用前完全
充电。
将电池组安装到工具手柄中
1. 将电池组 (f) 对齐工具手柄内的轨道。
2. 将电池组滑入手柄内,使其牢牢地固定在工具
内,并确保不会脱离。
从工具中取出电池组
1. 按电池释放按钮 (e),并用力将电池组从工具手
柄中拉出。
2. 按本手册充电器部分所述将电池组插入充电器
中。
电池组电量计(图 2
一些 DEWALT 电池组带有一个包含三个绿色 LED
指示灯的电量计,用于指示电池组内的剩余电量。
按下电量计按钮 (l) 不要松开,即可启动电量计。三
个绿色 LED 指示灯将以组合方式亮起,以指示剩余
电量。当电池内的电量低于可用限制时,电量计将
不会亮起,电池则必须重新充电。
注:电量计仅指示电池组的剩余电量。它并不表示
该工具的功能性能,且将根据产品组件、温度和最
终用户的使用情况而用所不同。
皮带扣和钻头夹具(图 1
警告:为了减少严重人身伤害的危险,
请勿将工具悬挂在头顶上方或用皮带扣
悬挂物品。只使用工作皮带悬挂工具的
皮带扣。
警告:为了减少严重人身伤害的危险,
确保固定皮带扣子的螺钉是牢固的。
重要:安装或更换皮带扣或钻头夹具时,只使用提
供的螺钉 (i)。切记要拧紧螺钉。
可使用提供的螺钉 (i) 将皮带扣 (h) 和钻头夹具 (j)
到工具的任意一侧,以方便习惯左手操作或习惯右
手操作的用户使用。无需皮带扣和钻头夹具时,可
以从工具上拆除。
要拆除皮带扣和钻头夹具时,卸下固定它们的螺钉
(i),然后在另一边重新装上。务必拧紧螺丝。
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

DeWalt DCF886 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

他の言語で

その他のドキュメント