JVC KD-G335 Instructions Manual

カテゴリー
カーメディアレシーバー
タイプ
Instructions Manual
ENGLISH
CD RECEIVER KD-G335
KD-G335
For canceling the display demonstration, see page 6.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0402-005A
[UT]
Cover_KD-G335_005A_f.indd 1Cover_KD-G335_005A_f.indd 1 9/22/06 12:36:28 PM9/22/06 12:36:28 PM
2
ENGLISH
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
How to reset your unit
Your preset adjustments will also be erased.
How to forcibly eject a disc
Be careful not to drop the disc when it ejects.
If this does not work, reset your unit.
Warning:
If you need to operate the unit while driving, be
sure to look ahead carefully or you may be involved
in a traffic accident.
Caution on volume setting:
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc
to avoid damaging the speakers by the sudden
increase of the output level.
[European Union only]
EN02-07_KD-G335[U_UH]1.indd 2EN02-07_KD-G335[U_UH]1.indd 2 8/30/06 5:22:00 PM8/30/06 5:22:00 PM
ENGLISH
3
How to use the M MODE button
If you press M MODE, the unit goes into functions
mode, then the number buttons and ¢/4
buttons work as different function buttons.
Ex.: When number button 2 works as
MO (monaural) button.
To use these buttons for their original functions
again after pressing M MODE, wait for 5 seconds
without pressing any of these buttons until the
functions mode is cleared or press M MODE again.
Detaching the control panel
Attaching the control panel
CONTENTS
Control panel .................................. 4
Remote controller —
RM-RK50 ........... 5
Getting started ................................ 6
Basic operations ................................................... 6
Radio operations ............................. 7
Disc operations ................................ 8
Playing a disc in the unit ..................................... 8
Sound adjustments .......................... 10
General settings — PSM .................. 11
Maintenance ................................... 13
More about this unit ........................ 14
Troubleshooting .............................. 16
Specifications .................................. 17
For safety...
Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
EN02-07_KD-G335[U_UH]1.indd 3EN02-07_KD-G335[U_UH]1.indd 3 8/30/06 5:22:03 PM8/30/06 5:22:03 PM
4
ENGLISH
u RND (random) button
i M MODE button
o (control panel release) button
; Disc information indicators—
TAG (Tag information), (track/file), (folder)
a DISC indicator
s Playback mode / item indicators—RND (random),
(disc), (folder), RPT (repeat)
d Tuner reception indicators—MO (monaural),
ST (stereo)
f S.BASS (super bass) indicator
g EQ (equalizer) indicator
h Tr (track) indicator
j Source display / Volume level indicator / Time
countdown indicator
k Main display
l Sound mode (iEQ: intelligent equalizer)
indicators—JAZZ, ROCK, HIP HOP, CLASSIC, POPS,
USER
Parts identification
Display window
Control panel
1 0 (eject) button
2 Loading slot
3 (standby/on/attenuator) button
4 Remote sensor
DO NOT expose the remote sensor to strong light
(direct sunlight or artificial lighting).
5 SOURCE button
6 Display window
7 BAND button
8 EQ (equalizer) button
9 ¢/4 buttons
p Control dial
q SEL (select) button
w DISP (display) button
e MO (monaural) button
r SSM (Strong-station Sequential Memory) button
t Number buttons
y RPT (repeat) button
EN02-07_KD-G335[U_UH]f.indd 4EN02-07_KD-G335[U_UH]f.indd 4 9/13/06 5:19:27 PM9/13/06 5:19:27 PM
ENGLISH
5
Remote controller — RM-RK50
Installing the lithium coin battery
(CR2025)
Aim the remote controller directly at the remote
sensor on the unit. Make sure there is no obstacle
in between.
Warning:
Do not install any battery other than CR2025 or
its equivalent; otherwise, it may explode.
Do not leave the remote controller in a place
(such as dashboards) exposed to direct sunlight
for a long time; otherwise, it may explode.
Store the battery in a place where children
cannot reach to avoid risk of accident.
To prevent the battery from over-heating,
cracking, or starting a fire:
Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
Do not leave the battery with other metallic
materials.
Do not poke the battery with tweezers or similar
tools.
Wrap the battery with tape and insulate when
throwing away or saving it.
Main elements and features
1 (standby/on/attenuator) button
Turns the power on if pressed briefly or
attenuates the sound when the power is on.
Turns the power off if pressed and held.
2 5 U (up) / D (down) buttons
Changes the FM/AM bands with 5 U.
Changes the preset stations with D .
Changes the folder of the MP3/WMA discs.
3 VOL – / VOL + buttons
Adjusts the volume level.
4 SOUND button
Selects the sound mode (iEQ: intelligent
equalizer).
5 SOURCE button
Selects the source.
6 2 R (reverse) / F (forward) 3 buttons
Searches for stations if pressed briefly.
Fast-forwards or reverses the track if pressed and
held.
Changes the tracks if pressed briefly.
EN02-07_KD-G335[U_UH]f.indd 5EN02-07_KD-G335[U_UH]f.indd 5 9/13/06 5:19:30 PM9/13/06 5:19:30 PM
6
ENGLISH
Basic settings
See also “General settings — PSM” on pages 11 and
12.
1
2
1 Canceling the display demonstrations
Select “DEMO,” then “DEMO OFF.”
2 Setting the clock
Select “CLOCK H” (hour), then adjust the hour.
Select “CLOCK M” (minute), then adjust the
minute.
3 Finish the procedure.
To check the current clock time while the
power is turned off
Clock time is shown on the
display for about 5 seconds. See
also page 12.
Getting started
Basic operations
~ Turn on the power.
Ÿ
* You cannot select “CD” as the playback source if
there is no disc in the unit.
! For FM/AM tuner
Adjust the volume.
@ Adjust the sound as you want. (See
pages 10 and 11.)
To drop the volume in a
moment (ATT)
To restore the sound, press the
button again.
To turn off the power
Volume level appears.
EN02-07_KD-G335[U_UH]f.indd 6EN02-07_KD-G335[U_UH]f.indd 6 9/7/06 2:33:06 PM9/7/06 2:33:06 PM
ENGLISH
7
When an FM stereo broadcast is hard to
receive
Reception improves, but stereo effect will be lost.
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO indicator
goes off.
Storing stations in memory
You can preset six stations for each band.
FM station automatic presetting
SSM (Strong-station Sequential
Memory)
1 Select the FM band (FM1 – FM3) you want to
store into.
2
3
“SSM” flashes, then disappears when automatic
presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
Radio operations
~
Ÿ
! Start searching for a station.
When a station is received,
searching stops.
To stop searching, press the
same button again.
To tune in to a station manually
In step ! above...
1
2
Select a desired station frequency.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Lights up when monaural mode is activated.
EN02-07_KD-G335[U_UH]f.indd 7EN02-07_KD-G335[U_UH]f.indd 7 9/13/06 4:49:44 PM9/13/06 4:49:44 PM
8
ENGLISH
Disc operations
Playing a disc in the unit
~ Turn on the power.
Ÿ
All tracks will be played repeatedly until you
change the source or eject the disc.
To stop play and eject the
disc
Press SOURCE to listen to
another playback source.
To fast-forward or reverse
the track
To go to the next or
previous tracks
To go to the next or previous folders (only
for MP3 or WMA discs)
Manual presetting
Ex.: Storing FM station of 92.5 MHz into preset number
4 of the FM1 band.
1
2
3
Listening to a preset station
1
2 Select the preset station (1 – 6) you want.
To check the other information while
listening to an FM or AM station
Preset number flashes for a while.
Clock Ô Frequency
EN08-13_KD-G335[U_UH]f.indd 8EN08-13_KD-G335[U_UH]f.indd 8 9/7/06 2:33:17 PM9/7/06 2:33:17 PM
9
ENGLISH
To locate a particular track (for CD) or folder
(for MP3 or WMA discs) directly
To select a number from 01 – 06:
To select a number from 07 – 12:
To use direct folder access on MP3/WMA discs, it
is required that folders are assigned with 2-digit
numbers at the beginning of their folder names—
01, 02, 03, and so on.
To select a particular track in a
folder (for MP3 or WMA disc):
Prohibiting disc ejection
You can lock a disc in the loading slot.
To cancel the prohibition, repeat the same
procedure.
Changing the display information
While playing an audio CD or a
CD Text
While playing an MP3 or a WMA disc
When “TAG DISP” is set to “TAG ON”
(see page 12)
When “TAG DISP” is set to “TAG OFF”
: Clock with the current track number
: Elapsed playing time with the current
track number
: Corresponding indicator lights up on the
display
*
1
If the current disc is an audio CD, “NO NAME” appears.
*
2
If an MP3/WMA file does not have Tag information,
folder name and file name appear. In this case, the
TAG indicator will not light up.
EN08-13_KD-G335[U_UH]f.indd 9EN08-13_KD-G335[U_UH]f.indd 9 9/13/06 4:50:56 PM9/13/06 4:50:56 PM
10
ENGLISH
Sound adjustments
You can select a preset sound mode suitable to the
music genre (iEQ: intelligent equalizer).
Indication (For)
BAS*
1
MID*
2
TRE*
3
S.BS*
4
USER
(Flat sound)
00 00 00 OFF
ROCK
(Rock or disco music)
+03 00 +02 ON
CLASSIC
(Classical music)
+01 00 +03 OFF
POPS
(Light music)
+02 +01 +02 OFF
HIP HOP
(Funk or rap music)
+04 –02 +01 ON
JAZZ
(Jazz music)
+03 00 +03 OFF
*
1
: Bass; *
2
: Middle; *
3
: Treble; *
4
: Super bass
Adjusting the sound
You can adjust the sound characteristics to your
preference.
1
2
Preset values
Selecting the playback modes
You can use only one of the following playback modes
at a time.
1
2 Select your desired playback mode.
7 Repeat play
Mode Plays repeatedly
TRK RPT : The current track.
FLDR RPT * : All tracks of the current folder.
RPT OFF : Cancels.
7 Random play
Mode Plays at random
FLDR RND * : All tracks of the current folder,
then tracks of the next folder and
so on.
DISC RND : All tracks of the current disc.
RND OFF : Cancels.
*
Only while playing an MP3 or a WMA disc.
: Corresponding indicator lights up on
the display
EN08-13_KD-G335[U_UH]f.indd 10EN08-13_KD-G335[U_UH]f.indd 10 9/13/06 5:19:51 PM9/13/06 5:19:51 PM
11
ENGLISH
Indication, [Range]
BAS *
2
(bass), [–06 to +06]
Adjust the bass.
MID *
2
(middle), [–06 to +06]
Adjust the middle frequencies sound level.
TRE *
2
(treble), [–06 to +06]
Adjust the treble.
FAD *
3
(fader), [R06 to F06]
Adjust the front and rear speaker balance.
BAL *
4
(balance), [L06 to R06]
Adjust the left and right speaker balance.
S.BS *
2
(super bass), [S.BS ON or S.BS OFF], [01 to 05]*
5
Maintain the richness and fullness of the bass sound
regardless of how low you set the volume.
SUB.W (subwoofer), [00 to 08]
Adjust the subwoofer output level.
VOL (volume), [00 to 30 or 50 *
6
]
Adjust the volume.
*
1
Displayed only when “L/O MODE” is set to “WOOFER”
(see page 12).
*
2
When you adjust the bass, middle, treble, or super
bass, the adjustment you have made is stored for the
currently selected sound mode (iEQ) including “USER.”
*
3
If you are using a two-speaker system, set the fader
level to “00.”
*
4
The adjustment cannot affect the subwoofer output.
*
5
Range adjustment for super bass is adjustable only
when it is set to “S.BS ON.”
*
6
Depending on the amplifier gain control setting. (See
page 12 for details.)
General settings — PSM
You can change PSM (Preferred Setting Mode) items
listed in the table that follows.
1
2 Select a PSM item.
3 Adjust the PSM item selected.
4 Repeat steps 2 and 3 to adjust other PSM
items if necessary.
5 Finish the procedure.
Continued on the next page
EN08-13_KD-G335[U_UH]f.indd 11EN08-13_KD-G335[U_UH]f.indd 11 9/13/06 6:51:01 PM9/13/06 6:51:01 PM
12
ENGLISH
Indications Item
( : Initial)
Selectable settings, [reference page]
DEMO
Display demonstration
DEMO ON
DEMO OFF
: Display demonstration will be activated automatically if no
operation is done for about 20 seconds, [6].
: Cancels.
CLK DISP *
1
Clock display
ON
OFF
:
Clock time is shown on the display at all times when the power is
turned off
.
: Cancels; pressing DISP will show the clock time for about
5 seconds when the power is turned off, [6].
CLOCK H
Hour adjustment
1 – 12 [Initial: 1 (1:00)], [6]
CLOCK M
Minute adjustment
00 – 59 [Initial: 00 (1:00)], [6]
DIMMER
Dimmer
ON
OFF
: Dims the display illumination.
: Cancels.
SCROLL *
2
Scroll
ONCE
AUTO
OFF
: Scrolls the disc information once.
: Repeats scrolling (at 5-second intervals).
: Cancels.
Pressing DISP for more than one second can scroll the display
regardless of the setting.
WOOFER *
3
Subwoofer cutoff
frequency
LOW
MID
HIGH
: Frequencies lower than 90 Hz are sent to the subwoofer.
: Frequencies lower than 135 Hz are sent to the subwoofer.
: Frequencies lower than 180 Hz are sent to the subwoofer.
L/O MODE
Line output mode
REAR
WOOFER
: Select if the REAR LINE OUT terminals are used for connecting the
speakers (through an external amplifier).
: Select if the REAR LINE OUT terminals are used for connecting a
subwoofer (through an external amplifier).
TAG DISP
Tag display
TAG ON
TAG OFF
: Shows the Tag information while playing MP3/WMA tracks, [9].
: Cancels.
AMP GAIN
Amplifier gain control
LOW PWR
HIGH PWR
: VOL 00 – VOL 30 (Select this if the maximum power of the
speaker is less than 50 W to prevent them from damaging the
speaker.)
: VOL 00 – VOL 50
*
1
If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select “OFF” to
save the car’s battery.
*
2
Some characters or symbols will not be shown correctly (or will be blanked) on the display.
*
3
Displayed only when “L/O MODE” is set to “WOOFER.”
EN08-13_KD-G335[U_UH]1.indd 12EN08-13_KD-G335[U_UH]1.indd 12 9/4/06 9:21:55 AM9/4/06 9:21:55 AM
13
ENGLISH
Maintenance
How to clean the connectors
Frequent detachment will deteriorate the connectors.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened with
alcohol, being careful not to damage the connectors.
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
After starting the heater in the car.
If it becomes very humid inside the car.
Should this occur, the unit malfunction. In this case,
eject the disc and leave the unit turned on for a few
hours until the moisture evaporates.
How to handle discs
When removing a disc from its
case, press down the center holder
of the case and lift the disc out,
holding it by the edges.
Always hold the disc by the edges.
Do not touch its recording surface.
When storing a disc into its case, gently insert the
disc around the center holder (with the printed surface
facing up).
Make sure to store discs into the cases after use.
Center holder
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with
a soft cloth in a straight line from center
to edge.
Do not use any solvent (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs.
To play new discs
New discs may have some rough spots
around the inner and outer edges. If
such a disc is used, this unit may reject
the disc.
To remove these rough spots, rub the edges with a
pencil or ball-point pen, etc.
Warped disc
Sticker
Sticker residue
Stick-on label
Do not use the following discs:
Connector
Unusual shape
Single CD (8 cm disc)
EN08-13_KD-G335[U_UH]f.indd 13EN08-13_KD-G335[U_UH]f.indd 13 9/7/06 2:33:32 PM9/7/06 2:33:32 PM
14
ENGLISH
MP3 and WMA “tracks” (words “file” and “track” are
used interchangeably) are recorded in “folders.”
While fast-forwarding or reversing on an MP3 or
WMA disc, you can only hear intermittent sounds.
Playing a CD-R or CD-RW
Use only “finalized” CD-Rs or CD-RWs.
This unit can play back only files of the same type
which are first detected if a disc includes both audio
CD (CD-DA) files and MP3/WMA files.
This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
Some CD-Rs or CD-RWs may not be played back on
this unit because of their disc characteristics, or for
the following reasons:
Discs are dirty or scratched.
Moisture condensation occurs on the lens inside
the unit.
The pickup lens inside the unit is dirty.
CD-R/CD-RW on which the files are written with
“Packet Write” method.
There are improper recording conditions (missing
data, etc.) or media conditions (stained, scratched,
warped, etc.).
CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than that of regular
CDs.
Do not use the following CD-Rs or CD-RWs:
Discs with stickers, labels, or protective seal stuck
to the surface.
Discs on which labels can be directly printed by an
ink jet printer.
Using these discs under high temperatures or high
humidities may cause malfunctions or damage to the
unit.
Playing an MP3/WMA disc
This unit can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
This unit can show the names of albums, artists
(performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or
2.4) for MP3 files and for WMA files.
More about this unit
Basic operations
Turning on the power
By pressing SOURCE on the unit, you can also turn on
the power. If the source is ready, playback also starts.
Turning off the power
If you turn off the power while listening to a disc, disc
play will start from where playback has been stopped
previously, next time you turn on the power.
Tuner operations
Storing stations in memory
During SSM search...
All previously stored stations are erased and
stations are stored newly.
Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
When SSM is over, the station stored in No. 1 will
be automatically tuned in.
When storing a station manually, the previously
preset station is erased when a new station is stored
in the same preset number.
Disc operations
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
General
This unit has been designed to reproduce
CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs
(Rewritable) in audio CD (CD-DA), MP3 and WMA
formats.
EN14-17_KD-G335[U_UH]f.indd 14EN14-17_KD-G335[U_UH]f.indd 14 9/20/06 4:38:32 PM9/20/06 4:38:32 PM
ENGLISH
15
Changing the source
If you change the source, playback also stops
(without ejecting the disc).
Next time you select “CD” for the playback source,
disc play starts from where it has been stopped
previously.
Ejecting a disc
If the ejected disc is not removed within 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust.
After ejecting a disc, “NO DISC” appears and you
cannot operate some of the buttons. Insert another
disc or press SOURCE to select another playback
source.
General settings—PSM
If you change the “AMP GAIN” setting from
“HIGH PWR” to “LOW PWR” while the volume level
is set higher than “VOL 30,” the unit automatically
changes the volume level to “VOL 30.”
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation
in the United States and/or other countries.
This unit can display only one-byte characters. No
other characters can be correctly displayed.
This unit can play back MP3/WMA files meeting the
conditions below:
Bit rate: 8 kbps — 320 kbps
Sampling frequency:
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
Disc format: ISO 9660 Level 1/ Level 2, Romeo,
Joliet, Windows long file name
The maximum number of characters for file/folder
names vary among the disc format used (includes 4
extension characters—<.mp3> or <.wma>).
ISO 9660 Level 1: up to 12 characters
ISO 9660 Level 2: up to 31 characters
Romeo: up to 64 characters
Joliet: up to 32 characters
Windows long file name: up to 128 characters
This unit can recognize a total of 512 files, of 200
folders, and of 8 hierarchies.
This unit can play back files recorded in VBR (variable
bit rate).
Files recorded in VBR have a discrepancy in elapsed
time display, and do not show the actual elapsed
time. Especially, after performing the search function,
this difference becomes noticeable.
This unit cannot play back the following files:
MP3 files encoded with MP3i and MP3 PRO format.
MP3 files encoded in an inappropriate format.
MP3 files encoded with Layer 1/2.
WMA files encoded with lossless, professional, and
voice format.
WMA files which are not based upon Windows
Media® Audio.
WMA files copy-protected with DRM.
Files which have the data such as WAVE, ATRAC3,
etc.
The search function works but search speed is not
constant.
EN14-17_KD-G335[U_UH]f.indd 15EN14-17_KD-G335[U_UH]f.indd 15 9/20/06 3:01:15 PM9/20/06 3:01:15 PM
16
ENGLISH
Symptoms Remedies/Causes
General
Sound cannot be heard from the speakers. Adjust the volume to the optimum level.
Check the cords and connections.
The unit does not work at all. Reset the unit (see page 2).
FM/AM
SSM automatic presetting does not work. Store stations manually.
Static noise while listening to the radio. Connect the antenna firmly.
Disc playback
Disc cannot be played back. Insert the disc correctly.
CD-R/CD-RW cannot be played back.
Tracks on the CD-R/CD-RW cannot be
skipped.
Insert a finalized CD-R/CD-RW.
Finalize the CD-R/CD-RW with the component which you
used for recording.
Disc can be neither played back nor ejected. Unlock the disc (see page 9).
Eject the disc forcibly (see page 2).
Disc sound is sometimes interrupted. Stop playback while driving on rough roads.
Change the disc.
Check the cords and connections.
“NO DISC” appears on the display. Insert a playable disc into the loading slot.
MP3/WMA playback
Disc cannot be played back. Use a disc with MP3/WMA tracks recorded in the
format compliant with ISO 9660 Level 1, Level 2,
Romeo, or Joliet.
Add the extension code <.mp3> or <.wma> to the
file names.
Noise is generated. Skip to another track or change the disc. (Do not add the
extension code <.mp3> or <.wma> to non-MP3 or
WMA tracks.)
A longer readout time is required (“CHECK”
keeps flashing on the display).
Do not use too many hierarchies and folders.
Tracks are not played back in the order you
have intended.
Playback order is determined when the files are recorded.
Elapsed playing time is not correct. This sometimes occurs during play. This is caused by how
the tracks are recorded on the disc.
“PLEASE EJECT” appears on the display. Insert a disc that contains MP3/WMA tracks.
Correct characters are not displayed (e.g.
album name).
This unit can only display alphabets (upper case),
numbers, and a limited number of symbols.
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
EN14-17_KD-G335[U_UH]f.indd 16EN14-17_KD-G335[U_UH]f.indd 16 9/20/06 3:01:16 PM9/20/06 3:01:16 PM
ENGLISH
17
Specifications
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Front/Rear: 50 W per channel
Continuous Power Output (RMS):
Front/Rear: 19 W per channel into 4 Ω,
40 Hz to 20 000 Hz at no more
than 0.8% total harmonic
distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass: ±12 dB at 60 Hz
Middle: ±12 dB at 1 kHz
Treble: ±12 dB at 7.5 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/
Impedance:
2.5 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
Subwoofer-Out
Level/Impedance:
2.0 V/20 kΩ load (full scale)
TUNER SECTION
Frequency Range:
FM: 87.5 MHz to 108.0 MHz
AM: 531 kHz to 1 602 kHz
FM Tuner
Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω)
50 dB Quieting
Sensitivity:
16.3 dBf (1.8 μV/75 Ω)
Alternate Channel
Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 30 dB
AM Tuner
Sensitivity/Selectivity: 20 μV/35 dB
CD PLAYER SECTION
Type: Compact disc player
Signal Detection
System:
Non-contact optical pickup
(semiconductor laser)
Number of Channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
MP3 Decoding Format: (MPEG1/2 Audio Layer 3)
Max. Bit Rate: 320 kbps
WMA (Windows Media® Audio) Decoding Format:
Max. Bit Rate: 192 kbps
GENERAL
Power Requirement:
Operating Voltage: DC 14.4 V
(11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating
Temperature:
0°C to +40°C
Dimensions (W × H × D): (approx.)
Installation Size: 182 mm × 52 mm × 158 mm
Panel Size: 187 mm × 58 mm × 13 mm
Mass:
1.3 kg (excluding accessories)
Design and specifications are subject to change without
notice.
EN14-17_KD-G335[U_UH]f.indd 17EN14-17_KD-G335[U_UH]f.indd 17 9/13/06 4:51:49 PM9/13/06 4:51:49 PM
© 2006 Victor Company of Japan, Limited
EN, CT
1006DTSMDTJEIN
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Rear_KD-G335_005A_f.indd 2Rear_KD-G335_005A_f.indd 2 9/11/06 3:05:25 PM9/11/06 3:05:25 PM
1
KD-G335
Installation/Connection Manual
GET0402-010A
[
UT]
1006DTSMDTJEIN
EN, CT
ENGLISH
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
12 V
JVC
© 2006 Victor Company of Japan, Limited
J
Handles
F
Washer (ø5)
ø5
G
Lock nut (M5)
M5
H
Mounting bolt (M5 × 20 mm)
M5 × 20 mm
I
Rubber cushion
A / B
Hard case/Control panel
C
Sleeve
D
Trim plate
E
Power cord
Parts list for installation and connection
The following parts are provided for this unit. If any item is missing, consult your JVC car audio dealer
immediately.
JVC
Heat sink
WARNINGS
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
Be sure to ground this unit to the car’s chassis again after installation.
Notes:
Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
It is recommended to connect to the speakers with maximum power of more than 50 W (both at
the rear and at the front, with an impedance of 4 to 8 ). If the maximum power is less than
50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 12 of the
INSTRUCTIONS).
To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
JVC
50 W 4 - 8
50 W
AMP GAIN
12
PRECAUTIONS on power supply and speaker connections:
DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
K
Remote controller
L
Battery
Instal1-2_KD-G335_009A_2.indd 1Instal1-2_KD-G335_009A_2.indd 1 2006.9.15 1:10:02 PM2006.9.15 1:10:02 PM
2
When installing the unit without using the sleeve /
In a Toyota car for example, first remove the car radio and install the unit in its place.
TOYOTA
When using the optional stay /
Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are
used, they could damage the unit.
8 mm
Flat type screws (M5 × 8 mm)
*
2
M5 × 8 mm *
2
Pocket
Flat type screws (M5 × 8 mm)
*
2
M5 × 8 mm *
2
Screw (option)
Stay (option)
Fire wall
Dashboard
Install the unit at an angle of less
than 30˚.
30˚
Bracket*
2
*
2
Removing the unit
Before removing the unit, release the rear section.
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
Do the required electrical connections.
*
1
When you stand the unit, be careful not to damage the fuse on the rear.
*
2
Not supplied for this unit.
Bend the appropriate tabs to hold the
sleeve firmly in place.
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
If you are not sure how to install this unit correctly, have it installed by a qualified technician.
JVC
Bracket*
2
*
2
*
1
*
2
Instal1-2_KD-G335_009A_1.indd 2Instal1-2_KD-G335_009A_1.indd 2 2006.9.15 10:36:53 AM2006.9.15 10:36:53 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

JVC KD-G335 Instructions Manual

カテゴリー
カーメディアレシーバー
タイプ
Instructions Manual

他の言語で