Dell 4220 クイックスタートガイド

Dell PowerEdge Rack

Enclosure

Installation Guide

Guide d’installation

Installationsanleitung

設置ガイド

Guía de instalación

Dell PowerEdge Rack

Enclosure

Installation Guide

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if

instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

July 2010 P/N JRY4T Rev. A00

Contents 3

Contents

Safety Instructions. . . . . . . . . . . . . . . . . . . . . 5

SAFETY: Rack Mounting of Systems

. . . . . . . . . 5

Rack Installation Instructions

. . . . . . . . . . . . . . . 5

Rack Specifications

. . . . . . . . . . . . . . . . . 6

Before You Begin

. . . . . . . . . . . . . . . . . . . 6

Installation Tasks

. . . . . . . . . . . . . . . . . . . 7

Recommended Tools and Supplies

. . . . . . . . . . 7

Removing and Replacing the Rack Doors

. . . . . . 8

Removing and Replacing the Side Panels

. . . . . 12

Reversing the Front Door (Optional)

. . . . . . . . 16

Securing the Rack Leveling Feet

. . . . . . . . . . 23

Installing the Rack Stabilizer Feet

. . . . . . . . . 24

Adjusting the Rack Posts (Optional)

. . . . . . . . 27

Routing Cables

. . . . . . . . . . . . . . . . . . . 28

Coupling Two Racks

. . . . . . . . . . . . . . . . . . . 32

4 Contents

Installation Guide 5

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to

help protect your system and working environment from potential damage.

For complete safety and regulatory information, see the safety instructions

that shipped with your system. Warranty information might be included in

this document or as a separate document.

SAFETY: Rack Mounting of Systems

Observe the following precautions for rack stability and safety. Also refer to

the rack installation documentation accompanying the system and the rack

for specific caution statements and procedures.

Systems are considered to be components in a rack. "Component" refers to

any system as well as to various peripherals or supporting hardware.

CAUTION: Instructions for Rack-Mounted Systems:

• Your rack kit has been approved only for the rack cabinet provided.

It is your responsibility to ensure that installation of the equipment

into any other rack complies with all applicable standards. Dell disclaims

all liability and warranties with respect to combinations of equipment

with any other rack.

• Before installing your equipment in a rack, install all front and side

stabilizers. Failure to install stabilizers can allow the rack to tip over.

• Always load from the bottom up, and load the heaviest items first.

• Do not overload the AC power supply branch circuit that provides

power to the rack.

• Do not stand or step on any components in the rack.

Rack Installation Instructions

This installation guide provides instructions for trained service technicians

installing a rack enclosure. Information includes assembling the rack,

coupling two racks, and routing cables through the rack. The rack can be

installed using the recommended tools.

Before attempting this installation, you should read through this entire

procedure carefully.

6 Installation Guide

Rack Specifications

CAUTION: The rack meets the specifications of American National Standards

Institute (ANSI), Consumer Electronics Association (CEA) Standard EIA/CEA-310-E,

International Electrotechnical Commission (IEC) 60297-3-100, and Deutsche Industrie

Norm (DIN) 41494.

Before You Begin

WARNING: Before you begin installing your rack, carefully read "Important

Safety Information," as well as the safety instructions that came with the rack.

WARNING: When installing multiple systems in a rack, complete all of the

procedures for the current system before attempting to install the next system.

WARNING: Rack cabinets can be extremely heavy and move easily on the

casters. The cabinet has no brakes. Use extreme caution while moving the rack

cabinet. Retract the leveling feet when relocating the rack cabinet. Avoid long or

steep inclines, rough surfaces, or ramps where loss of cabinet control may occur.

Extend the leveling feet for support and to prevent the cabinet from rolling.

WARNING: Avoid rolling the rack cabinet over rough surfaces. Hard impacts to

the casters could cause them to break, and the rack could become unstable and

may tip over.

WARNING: Do not attempt to move your rack with components installed. If you

move a fully loaded rack on a slightly uneven surface, the rack may become

unstable and may tip over.

Important Safety Information

Observe the safety precautions in the following subsections when installing

your system in the rack.

WARNING: You must strictly follow the procedures in this document to protect

yourself as well as others who may be involved. Your system may be very large

and heavy, and proper preparation and planning are important to prevent injury

to yourself and to others. This becomes increasingly important when systems

are installed high up in the rack.

Installation Guide 7

Rack Stabilizer Feet

WARNING: Before installing systems in a rack, install front and side stabilizers

on stand-alone racks or the front stabilizer on racks joined to other racks.

Failure to install stabilizers accordingly before installing systems in a rack

could cause the rack to tip over, potentially resulting in bodily injury under certain

circumstances. Therefore, always install the stabilizer(s) before installing

components in the rack.

WARNING: After installing systems in a rack, never pull more than one system

out of the rack on its slide assemblies at one time. The weight of more than one

extended system could cause the rack to tip over and cause injury.

The stabilizer feet help prevent the rack from tipping over when a system

or other component is pulled out of the rack with the slide assemblies

fully extended.

Installation Tasks

Installing a rack cabinet involves the following tasks:

1

Removing and replacing the rack doors

2

Removing and replacing the side panels

3

Reversing the front door and badge (optional)

4

Securing the leveling feet

5

Installing the stabilizer feet

6

Adjusting the rack posts (optional)

7

Routing cables through the rack

8

Coupling two racks (optional)

Recommended Tools and Supplies

You may need the following tools and supplies to install the rack:

• #2 Phillips screwdriver

• Flat head screwdriver

• 12-mm wrench

8 Installation Guide

• Needle-nose pliers

• 4-mm Allen wrench (if you want to reverse the direction that

the front door opens)

• Keys to the rack doors and side panels

• 13-mm wrench (for rack removal from pallet)

• 17-mm wrench (for rack removal from pallet)

Removing and Replacing the Rack Doors

WARNING: Because of the size and weight of the rack cabinet doors,

never attempt to remove or install them by yourself.

WARNING: When storing the doors, lay the doors flat so they do not fall over

and accidentally injure someone.

Removing the Front Door

1

Pull the door latch and open the front door all the way (see Figure 1-1).

2

While holding the door, pull the hinge pin upward so that it clears the

door’s hinge-pin housing (see Figure 1-1).

The hinge pin’s retention clip prevents the hinge from being pulled out of

the hinge body.

Installation Guide 9

Figure 1-1. Removing the Front Door

3

While holding the hinge pin out of the door’s hinge-pin housing, pull the

door slightly away from the rack so that the door clears the hinge body.

4

Release the hinge pin.

5

Lift the door upward so that the door clears the bottom hinge post.

WARNING: Due to the size and weight of the door, it is recommended that you lay

the removed door flat with its outer surface facing upward.

6

Lay the door in a safe location with the door’s outer surface facing upward

to help prevent damage to the door’s badge and cosmetic coating.

1 door latch 2 hinge pin

3 hinge body 4 hinge-pin housing

4

2

3

1

10 Installation Guide

Replacing the Front Door

To replace the front door, perform the steps for removal in reverse.

Opening and Removing the Back Doors

WARNING: Because of the size and weight of the rack cabinet doors, never

attempt to remove or install them by yourself.

1

Turn the door handle and open the back doors (see Figure 1-2).

Figure 1-2. Opening the Back Doors

1 door handle 2 back door (2)

2

1

Installation Guide 11

2

Remove the right back door.

a

While supporting the door, pull the pin for the top hinge out of the

door’s hinge-pin housing (see Figure 1-3).

You will hear a click sound as you pull the pin out of the door’s

hinge-pin housing. The hinge pins are designed to prevent them

from being pulled out of the hinge body.

b

Repeat step a for the bottom hinge.

c

Pull the door away from the rack.

Figure 1-3. Removing the Back Doors

WARNING: Due to the size and weight of the door, it is recommended that you lay

the removed door flat with its outer surface facing upward.

1 hinge pin 2 hinge body

3 hinge-pin housing

1

2

3

12 Installation Guide

d

Lay the door in a safe location with the door’s outer surface

facing upward.

Laying the door flat with the outer surface facing upward helps

prevent damage to its cosmetic coating.

e

Repeat step a through step d for the left back door.

Replacing the Back Doors

To replace the back doors, perform the steps for removal in reverse.

Removing and Replacing the Side Panels

CAUTION: For stand-alone racks, reinstalling the side panels is necessary

before running systems in the rack to ensure proper cooling within the rack.

NOTE: You must remove the lower side panels in order to install the side

stabilizer feet.

NOTE: Although removing the side panels is not mandatory for installing

systems in a rack, having the sides open makes it easier to install slide assemblies

and support rails and to reverse the direction that the front door opens.

Removing the Upper Side Panels

1

Push both latches up and swing the bottom end of the panel away

from the rack (see Figure 1-4).

2

Grasp firmly on each side of the panel.

3

Lift the panel upward until the panel lip clears the top of the rack.

4

Lay the panel in a safe location with the panel’s outer surface facing

upward to help prevent damage to its cosmetic coating.

5

Repeat step 1 through step 4 for the other upper side panel.

Replacing the Upper Side Panels

1

Lift the upper side panel up onto the rack, hooking the panel lip over the

top of the rack (see Figure 1-4).

2

Swing the bottom of the panel downward onto the rack.

3

Press the panel into the rack until both latches lock into place.

Installation Guide 13

Figure 1-4. Replacing the Upper Side Panels

Removing the Lower Side Panels

1

Pull both latches down and allow the side panel to swing outward

slightly at the top.

2

Firmly grasp both sides of the panel.

3

Lift the panel upward until the panel hooks clear the holes in the

bottom of the rack frame.

4

Place the panel in a safe location with the panel’s outer surface facing

upward to help prevent damage to its cosmetic coating.

5

Repeat step 1 through step 4 for the other lower side panel.

1 panel lip 2 upper side panel (2)

3 latches (2)

2

3

1

14 Installation Guide

Replacing the Lower Side Panels

1

Lower the panel into the rack, inserting the back panel hook into

the back hole in the bottom of the rack frame and the front hook into

the corresponding hole in the front of the rack frame (see Figure 1-5).

2

Swing the top end of the panel towards the rack.

3

Press the panel into the rack until both latches lock into place.

Figure 1-5. Replacing the Lower Side Panels

NOTE: The following procedures apply to extra-deep racks only.

1 panel hook (2) 2 latch (2)

3 lower side panel (2)

1

2

3

Installation Guide 15

Removing the Rear Side Panel

1

Remove the screws (2) holding the rear side panel in place from inside the rack.

2

Lift the rear side panel up and away from the rack.

Replacing the Rear Side Panel

1

Insert the alignment bracket located in the middle of the rear panel into

the slot on the rack PDU tray.

2

Install screws at the top and bottom to secure the rear side panel.

Figure 1-6. Replacing the Rear Side Panels

1 rear side panel 2 screw (2)

3 alignment bracket 4 slot in PDU tray

1

3

4

2

16 Installation Guide

Reversing the Front Door (Optional)

NOTE: Use a 4-mm Allen wrench to remove the front-door hinge bodies from the rack

and reinstall them on the side opposite their original positions. You might need a

stepladder in order to access the Allen bolt that secures the top hinge body to the rack.

To reverse the direction that the front door opens, complete the following steps:

1

Remove the front door (see "Removing the Front Door" on page 8).

2

Remove the side panels (see "Removing and Replacing the Side Panels" on

page 12).

3

Reverse the top hinge body.

a

Pull the hinge pin slightly upward so that you can access the retention

clip (see Figure 1-7).

b

Using the needle-nose pliers, remove the retention clip, and slide the

hinge pin out of the hinge body.

Installation Guide 17

Figure 1-7. Removing the Front-Door Hinges

c

Remove the hinge spring from the hinge body.

d

Place the hinge pin, retention clip, and spring in a safe location.

e

Using the 4-mm Allen wrench, remove the Allen bolts that secure the

hinge body to the rack, and place the bolts with the hinge pin,

retention clip, and body spring.

f

Rotate the hinge body 180 degrees so that the hinge-pin holes are

now on the right side of the hinge body (see Figure 1-8).

1 hinge pin 2 top hinge

3 bottom hinge 4 hinge post

5 retention clip 6 body spring

1

6

5

2

3

4

18 Installation Guide

Figure 1-8. Reversing the Top and Bottom Hinges

g

Locate the top bolt holes in the right side of the rack, and fasten the

hinge body to the right side of the rack with the Allen bolts.

h

Insert the spring between the top and bottom hinge-pin holes in the

bottom hinge body.

1 hinge pin 2 top hinge body

3 spring 4 retention clip

5 hinge post 6 bottom hinge body

7 front of rack

2

3

4

1

5

6

7

ページを読み込んでいます...