H3C LSWM2QP2P ユーザーマニュアル

タイプ
ユーザーマニュアル
1
H3C LSWM2QP2P Interface Card User Manual-6PW103
H3C LSWM2QP2P
-6PW103
BOM: 3101A0H6
The LSWM2QP2P interface card provides two QSFP+ ports.
LSWM2QP2P接口模块扩展卡对外可提供2QSFP+口。
Overview
Installing and removing the card
Prepare the following tools before you install or remove the card: Phillips screwdriver,
flat-blade screwdriver, and ESD wrist strap. 在安装与拆卸接口模块扩展卡前,您需要
准备的工具包括十字螺丝刀、一字螺丝刀和防静电腕带。
No installation tools are provided with the device. Prepare these tools yourself. H3C
随机提供安装工具,您需要提前准备这些安装工具。
QSFP+ port LED
QSFP+口状态指示灯
Ejector lever
扳手
Captive screw
松不脱螺钉
QSFP+ port
QSFP+
The switch models that the LSWM2QP2P interface card is applicable to may change
over time. For the most up-to-date list of applicable switch models, contact H3C Support
or marketing staff. LSWM2QP2P接口模块扩展卡适用于H3C款交换机产品,其适用机
型的准确信息随着时间变化有更新的可能性,若您需要更详细的适配信息,请咨询H3C
司市场人员或技术支持人员
2
Before you install or remove the card, wear an ESD wrist strap and make sure the
strap makes good skin contact and is reliably grounded. 在安装和拆卸过程中,操作者
需自行准备并佩戴防静电腕带,请确保防静电腕带已经正确接地并与皮肤良好接触。
To avoid device damage, do not use excessive force when you install or remove the
card. 在安装和拆卸过程中,请不要用力过猛,以免对设备器件造成损坏。
Safety precautions 安全注意事项
1
Installing the card 接口模块扩展卡的安装
Remove the filler panel (if any) from the target slot before installing the card. Keep the
removed screw and filler panel secure for future use.如果交换机的接口模块扩展卡插槽
上装有假面板,请先将假面板拆除再进行接口模块扩展卡的安装,并请妥善保存拆卸下
的假面板
以及固定该假面板的紧固螺钉以备将来使用。
Removing the card 接口模块扩展卡的拆卸
To avoid cable damage, remove the cables from the card before removing the card.
在拆卸接口模块扩展卡之前,推荐您先将接口模块扩展卡上的线缆拔出,以免在拆卸
过程中对线缆造成损坏。
If you are not to install a new card after removing the original one, install a filler panel
in the slot to prevent dust and ensure good ventilation in the device. 若接口模块扩
展卡拆卸完成后无须安装新的接口模块扩展卡,请您及时安装假面板,以保证设备的
良好通风散热并防止灰尘进入设备。
Place the removed card on an anti-static mat or in an anti-static bag. 请将拆卸下来的
接口模块扩展卡及时放置到防静电垫子上或防静电袋中。
3
Unpack the card. Insert the card slowly into the slot along the guide rails. 从包装袋中取出接口
块扩展卡,并将接口模块扩展卡沿着插槽导轨水平缓慢地推进接口模块扩展卡插槽。
Rotate inward the ejector lever until the card is in close contact with the switch. 将扳手用力向内
扣合,确保接口模块扩展卡和交换机紧密接触。
Use the Phillips screwdriver to tighten the captive screw on the card. 使用十字螺丝刀顺时针方
向旋转,拧紧接口模块扩展卡上的松不脱螺钉。
2
1
2
3
3
Verifying the installation
After the installation is complete, determine whether the card is operating correctly. If
the card fails to operate correctly, perform the following steps:
Reinstall the card following the installation procedures described in this document.
If the problem persists, contact H3C Support.
全部安装完成后,在交换机运行正常的情况下,若发现接口模块扩展卡无法正常工作:
您可以按照手册中介绍的方法重新安装接口模块扩展卡
如果重新安装后,接口模块扩展卡仍无法正常工作,请您联系H3C技术支持人员。
4
For the installation and removal procedures for QSFP+ transceiver modules or cables,
see H3C Transceiver Modules and Network Cables Installation Guide at www.h3c.com.
对于QSFP+模块、QSFP+电缆、QSFP+ to SFP+电缆的安装与拆卸,请您参见H3C网站
发布的《H3C模块及线缆 安装指导》中的相关内容。
Use a Phillips screwdriver to loosen the captive screw on the card. 使用十字螺丝刀逆时针
方向旋转,松开接口模块扩展卡上的松不脱螺钉。
Hold the ejector lever to pull the card outward until the card is disconnected from the
connectors. 拉动扳手使接口模块扩展卡与设备内连接器端子脱离。
Hold the card with both hands and take it out slowly. 用双手水平缓慢地取出接口模块扩展卡。
4
2
3
1
Installing and removing transceiver modules and cables光模块或线缆的安装与拆卸
4
Model
型号
Central
wavelength
中心波长
Connector
接口连接器
Cable
specifications
接口线缆规格
Modal
bandwidth
模式带宽
(MHz*km)
Max
transmission
distance
最大传输距离
QSFP+ transceiver modules QSFP+模块
QSFP-40
G-SR4-M
M850
850 nm MPO
50/125µm
MFF
2000 100m
4700 150m
QSFP-40
G-CSR4-
MM850
850 nm MPO
50/125µm
MFF
2000 300m
4700 400m
QSFP-40
G-LR4-W
DM1300
Four lanes:
1271
1291
1311
1331
LC 9/125µm SMF N/A
10 km (6.21
miles)
Model 型号 Cable length 线缆长度 Data rate 传输速率
QSFP+ DAC cables QSFP+电缆
LSWM1QSTK0 1 m (3.28 ft)
40 Gbps
LSWM1QSTK1 3 m (9.84 ft)
LSWM1QSTK2 5 m (16.40 ft)
QSFP+ to SFP+ DAC cables QSFP+ to SFP+电缆
LSWM1QSTK3 1 m (3.28 ft)
40 Gbps
LSWM1QSTK4 3 m (9.84 ft)
LSWM1QSTK5 5 m (16.40 ft)
LED Status 指示灯状态 Description 指示灯含义
Steady green
绿色常亮
A transceiver module is installed in the port. The port is
operating at 40 Gbps, and a link is present on the port.
模块已安装,端口工作在
40GE
模式下,并且端口
Link Up
Flashing green
绿色闪烁
The port is sending or receiving data at 40 Gbps.
端口工作在
40GE
模式下,正在接收或发送数据
Steady yellow
黄色常亮
A transceiver module is installed in the port. The port is
operating at 10 Gbps, and a link is present on the port.
模块已安装,端口工作在
10GE
模式下,并且端口
Link Up
Flashing yellow
黄色闪烁
The port is sending or receiving data at 10 Gbps.
端口工作在
10GE
模式下,正在接收或发送数据
Off
灯灭
No transceiver module is installed in the port, or no link is
present on the port.
模块没有安装或端口没有
Link Up
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

H3C LSWM2QP2P ユーザーマニュアル

タイプ
ユーザーマニュアル

他の言語で