Dell PowerEdge 1955 クイックスタートガイド

Rack Installation Guide

Guide d'installation du rack

Rack-Installationsanleitung

ラック取り付けガイド

Guía de instalación del rack

Rack Installation Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: RapidRails and VersaRails are trademarks of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names

or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

July 2005 P/N F3159 Rev. A01

Contents 3

Contents

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SAFETY: Rack Mounting of Systems

. . . . . . . . . . . . . . . . . . . . . 5

Installation Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Before You Begin

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation Tasks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Recommended Tools and Supplies

. . . . . . . . . . . . . . . . . . . . . . 7

RapidRails Rack Kit Contents

. . . . . . . . . . . . . . . . . . . . . . . . . 7

VersaRails Rack Kit Contents

. . . . . . . . . . . . . . . . . . . . . . . . . 8

Removing the Rack Doors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Marking the Rack

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing the RapidRails Assemblies

. . . . . . . . . . . . . . . . . . . . . . 10

Installing the VersaRails Assemblies

. . . . . . . . . . . . . . . . . . . . . . 11

Installing the System in the Rack

. . . . . . . . . . . . . . . . . . . . . . . . 12

Routing Cables

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Replacing the Rack Doors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figures

Figure 1-1. RapidRails Rack Kit Contents . . . . . . . . . . . . . 8

Figure 1-2. VersaRails Rack Kit Contents

. . . . . . . . . . . . . 8

Figure 1-3. One Rack Unit

. . . . . . . . . . . . . . . . . . . . . 9

Figure 1-4. Marking the Vertical Rails

. . . . . . . . . . . . . . 10

Figure 1-5. Installing the RapidRails Assemblies

. . . . . . . . . 11

Figure 1-6. Installing the VersaRails Rail Assemblies

. . . . . . 12

Figure 1-7. Installing the System in the Rack

. . . . . . . . . . . 13

Figure 1-8. Securing the Cables to the Rack

. . . . . . . . . . . 14

4 Contents

Rack Installation Guide 5

Safety Instructions

Use the following safety guidelines to help ensure your own personal safety and to help protect

your system and working environment from potential damage. For complete safety information,

see the

Product Information

Guide

.

SAFETY: Rack Mounting of Systems

Observe the following precautions for rack stability and safety.

Systems are considered to be components in a rack. Thus, "component" refers to any system as well

as to various peripherals or supporting hardware.

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks

or the front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before

installing systems in a rack could cause the rack to tip over, potentially resulting in bodily injury under

certain circumstances. Therefore, always install the stabilizer(s) before installing components in the

rack.

CAUTION: After installing system/components in a rack, never pull more than one component out of

the rack on its slide assemblies at one time. The weight of more than one extended component could

cause the rack to tip over and injure someone.

NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a rack

cabinet using the customer rack kit when both the rack cabinet and rack kit were designed for your

system. The installation of your system and rack kit in any other rack cabinet has not been

approved by any safety agencies. It is your responsibility to have the final combination of system

and rack kit in a cabinet evaluated for suitability by a certified safety agency. The manufacturer

disclaims all warranties and liability in connection with such combinations.

•

System rack kits are intended to be installed in an approved rack by trained service

technicians. If you install the kit in any other rack, be sure that the rack meets the

specifications.

• Before working on the rack, make sure that the stabilizers are secured to the rack, extended to

the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers

on a single rack or front stabilizers for joined multiple racks before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from the rack.

• Do not overload the AC power supply branch circuit that provides power to the rack.

The total rack load should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any system/component when servicing other systems/components

in a rack.

6 Rack Installation Guide

Installation Instructions

This installation guide provides instructions for trained service technicians installing one or more

systems in an open-frame relay rack or in a rack cabinet. The RapidRails™ rack kit can be installed

without tools in manufacturer’s rack cabinets that have square holes; the VersaRails™ rack kit can

be installed in most industry-standard rack cabinets that have square or round holes. The

procedures for installing both RapidRails and VersaRails rack kits are similar. One rack kit is

required for each system installed in the rack.

CAUTION: Do not install rack kit components designed for another system. Use only the rack kit for

your system. Using the rack kit for another system may result in damage to the system and personal

injury.

The VersaRails rack kit can be installed in most industry-standard rack cabinets.

NOTICE: The VersaRails rack kit is intended to be installed by trained service technicians in a rack that

meets the specifications of American National Standards Institute (ANSI)/Electronic Industries

Association (EIA) standard ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and

Deutsche Industrie Norm (DIN) 41494. One rack kit is required for each system that is installed in a rack.

Before You Begin

Before you begin installing your system in the rack, carefully read "Safety Instructions," found

earlier in this guide, as well as the safety instructions found in your

Product Information Guide

for

additional information.

CAUTION: When installing multiple systems in a rack, complete all of the procedures for the current

system before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on the casters. The cabinet has no

brakes. Use extreme caution while moving the rack cabinet. Retract the leveling feet when relocating

the rack cabinet. Avoid long or steep inclines or ramps where loss of cabinet control may occur. Extend

the leveling feet for support and to prevent the cabinet from rolling.

Important Safety Information

Observe the safety precautions in the following subsections when installing your system in the rack.

CAUTION: You must strictly follow the procedures in this document to protect yourself as well as

others who may be involved. Your system may be very large and heavy, and proper preparation and

planning are important to prevent injury to yourself and to others. This becomes increasingly important

when systems are installed high up in the rack.

Rack Stabilizer Feet

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks

or the front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before

installing systems in a rack could cause the rack to tip over, potentially resulting in bodily injury under

certain circumstances. Therefore, always install the stabilizer(s) before installing components in the

rack.

Rack Installation Guide 7

CAUTION: After installing systems in a rack, never pull more than one system out of the rack on its

slide assemblies at one time. The weight of more than one extended system could cause the rack

to tip over and cause injury.

The stabilizer feet help prevent the rack from tipping over when a system or other component is

pulled out of the rack with the slide assemblies fully extended. See the documentation provided

with the rack cabinet for instructions on installing and anchoring the stabilizer feet.

Installation Tasks

Installing a rack kit involves performing the following tasks in their numbered order:

1

Removing the rack doors

2

Marking the rack (if necessary)

3

Installing the rail assemblies in the rack:

• RapidRails installation

• VersaRails installation

4

Installing the system in the rack

5

Routing cables

6

Replacing the rack doors

Recommended Tools and Supplies

• A #2 Phillips screwdriver

• Masking tape or a felt-tip pen, for use in marking the mounting holes to be used

• A measuring ruler or tape measure

RapidRails Rack Kit Contents

The RapidRails rack kit includes the following items (see Figure 1-1):

• One pair of RapidRails assemblies

• Four reusable tie wraps

8 Rack Installation Guide

Figure 1-1. RapidRails Rack Kit Contents

VersaRails Rack Kit Contents

The VersaRails rack kit includes the following items (see Figure 1-2):

• One pair of VersaRails assemblies

• Four reusable tie wraps

• Twelve 10-32 x 0.5-inch flange-head Phillips screws

NOTE: Nonmetric screws are identified in this document by size and number of threads per inch.

For example, a #10 Phillips-head screw with 32 threads per inch is identified as a 10-32 screw.

Figure 1-2. VersaRails Rack Kit Contents

RapidRails assemblies

tie-wraps (4)

10-32 x 0.5-inch flange-

head Phillips screws (12)

VersaRails assemblies

tie-wraps (4)

Rack Installation Guide 9

Removing the Rack Doors

See the procedures for removing doors in the documentation provided with your rack cabinet.

CAUTION: Because of the size and weight of the rack cabinet doors, never attempt to remove or install

them by yourself.

CAUTION: Store the two doors where they will not injure someone if the doors accidently fall over.

Marking the Rack

You must allow 7 U (31.1 cm or 12.25 inches) of vertical space for each system you install

in the rack (see Figure 1-3).

NOTE: Your rack may already be marked and not require this procedure.

CAUTION: If you are installing more than one system, install the rail assemblies so that the first system

is installed in the lowest available position in the rack.

1

Place a mark on the rack’s front vertical rails where you want to locate the bottom

of the system you are installing in the rack cabinet.

The bottom of each 1-U space is at the middle of the narrowest metal area between holes

(marked with a horizontal line on some rack cabinets—see Figure 1-3).

Figure 1-3. One Rack Unit

1 U (44 mm or 1.75 inches)

12.7 mm (0.5 inch)

15.9 mm (0.625 inch)

12.7 mm (0.5 inch)

10 Rack Installation Guide

2

Mark the rack’s front vertical rails with a felt-tipped pen or masking tape approximately 31.1

cm (12.25 inches) above the original mark you made (or count up 21 holes in a rack that

meets EIA-310 standards). (If you counted holes, place a mark just above the top hole.)

This mark or piece of tape indicates where the system’s upper edge will be located on

the vertical rails (see Figure 1-4).

Figure 1-4. Marking the Vertical Rails

Installing the RapidRails Assemblies

1

At the front of the rack cabinet, position one of the RapidRails assemblies so that its

mounting-bracket flange fits in the appropriate location on the rack (see Figure 1-5).

The lower mounting hook on the rail assembly’s front-mounting bracket flange should enter

the third hole up from the bottom mark on the vertical rails.

2

Push the rail assembly forward until the top mounting hook enters the square hole just below

the upper marks or tape you placed on the vertical rail. Next, push down on the mounting-

bracket flange until the mounting hooks seat in the square holes and the push button pops

out and clicks (see Figure 1-5).

tape on vertical rail

Rack Installation Guide 11

3

At the back of the cabinet, pull back on the mounting-bracket flange until the mounting

hooks are in the appropriate holes, and then push down on the flange until the mounting

hooks seat in the square holes and the push button pops out and clicks.

4

Repeat steps 1 through 3 for the rail assembly on the other side of the rack.

NOTE: Ensure that the rails are mounted at the same vertical position on both sides of the rack.

Figure 1-5. Installing the RapidRails Assemblies

Installing the VersaRails Assemblies

1

At the front of the rack cabinet, place a VersaRails assembly so that its mounting-bracket

flange fits between the marks or tape (or numbered location) on the rack (see Figure 1-6).

The holes on the front of the mounting bracket should align with the holes between

the marks on the front vertical rail.

2

Install three 10-32 x 0.5-inch flange-head Phillips screws to secure the rail assembly

to the front vertical rail (see Figure 1-6).

rail-assembly mounting-bracket flange

push button

front of rack

rail assemblies (2)

mounting hooks (2)

12 Rack Installation Guide

3

At the back of the cabinet, pull back on the mounting-bracket flange until the mounting

holes align with their respective holes on the back vertical rail.

4

Install three 10-32 x 0.5-inch flange-head Phillips screws in the back mounting flange

to secure the rail assembly to the back vertical rail.

5

Repeat steps 1 through 4 for the rail assembly on the other side of the rack.

NOTE: Ensure that the rails are mounted at the same vertical position on both sides of the rack.

Figure 1-6. Installing the VersaRails Rail Assemblies

Installing the System in the Rack

CAUTION: If you are installing more than one system, install the first system in the lowest available

position in the rack.

CAUTION: Never pull more than one component out of the rack at a time.

CAUTION: Because of the size and weight of the system, never attempt to install the system in the rack

by yourself.

rail assembly

mounting-bracket

flange

front of rack

rail assemblies (2)

flange-head

Phillips screws (3)

vertical rail

Rack Installation Guide 13

CAUTION: It is recommended that more than one person assist in lifting the system.

NOTICE: It is recommended that you use a lift table to aid in installing the system in the rack, particularly

if the rail assemblies are more than waist-high.

1

Lift the system into position to install it in the rack.

It is recommended that more than one person assist in lifting the system.

2

Guide the system into the rack and lower the system onto the rail assemblies (see Figure 1-7).

3

Tighten the thumbscrews on the rack front panel.

Figure 1-7. Installing the System in the Rack

Routing Cables

1

Attach the I/O cable connectors and power cables to their respective connectors on the

system back panel. For details on cable connections, see your system’s

Getting Started Guide

,

Installation and Troubleshooting Guide

, and

User’s Guide

.

NOTE: Use the strain-relief loops (if available) on the back of the power supplies to provide strain

relief for the power cables.

rail assemblies (2)

thumbscrews (4)

14 Rack Installation Guide

2 Using the following guidelines, secure the cables to the rack’s back vertical rails using

the four releasable tie-wraps supplied in the rack kit (see Figure 1-8).

– To improve serviceability and airflow, create two bundles of cables on each side of the

system, keeping the area directly in back of the system as clear of cables as possible.

– Create separate bundles of cables for the I/O cables and the power cables.

– If the cables are sufficiently flexible, leave 10–15 cm (4–6 inches) of slack in the cables

between the cable tie and the system, to improve serviceability of the modules.

Figure 1-8. Securing the Cables to the Rack

Replacing the Rack Doors

See the procedures for replacing doors in the documentation provided with your rack cabinets.

This completes the rack installation of your system.

tie-wraps (4)

cables

vertical rail

I/O cables

power cables

Index 15

Index

C

cable routing, 13

D

doors

removing, 9

replacing, 14

I

installing

system in the rack, 12

K

kit contents

RapidRails, 7

VersaRails, 8

M

marking the rack, 9

R

rack

marking, 9

rack mount precautions, 6

rack stabilizer feet, 6

RapidRails kit contents, 7

routing cables, 13

S

safety instructions, 5

T

tools and supplies

four-post kits, 7

V

VersaRails

kit contents, 8

16 Index

Guide d'installation du rack

Remarques, avis et précautions

REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser

votre ordinateur.

AVIS : un AVIS vous avertit d'un risque de dommage matériel ou de perte de données et vous indique comment éviter

le problème.

PRÉCAUTION : une PRÉCAUTION indique un risque potentiel d'endommagement du matériel, de blessure corporelle

ou de mort.

____________________

Les informations contenues dans ce document peuvent être modifiées sans préavis.

La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc. est strictement interdite.

Marques utilisées dans ce document : RapidRails et VersaRails sont des marques de Dell Inc.

Tous les autres noms de marques et marques commerciales utilisés dans ce document se rapportent aux sociétés propriétaires des marques et

des noms de ces produits. Dell Inc. décline tout intérêt dans l'utilisation des marques déposées et des noms de marques ne lui appartenant pas.

Juillet 2005 P/N F3159 Rev. A01

ページが読み込まれています...

Dell PowerEdge 1955 クイックスタートガイド

Dell PowerEdge 1955 クイックスタートガイド

他の言語で

関連論文