Dell PowerEdge 1955 クイックスタートガイド

カテゴリー
ラックアクセサリー
タイプ
クイックスタートガイド
Rack Installation Guide
Guide d'installation du rack
Rack-Installationsanleitung
ラック取り付けガイド
Guía de instalación del rack
Rack Installation Guide
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2005 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: RapidRails and VersaRails are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names
or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
July 2005 P/N F3159 Rev. A01
Contents 3
Contents
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY: Rack Mounting of Systems
. . . . . . . . . . . . . . . . . . . . . 5
Installation Instructions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Before You Begin
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation Tasks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Recommended Tools and Supplies
. . . . . . . . . . . . . . . . . . . . . . 7
RapidRails Rack Kit Contents
. . . . . . . . . . . . . . . . . . . . . . . . . 7
VersaRails Rack Kit Contents
. . . . . . . . . . . . . . . . . . . . . . . . . 8
Removing the Rack Doors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Marking the Rack
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the RapidRails Assemblies
. . . . . . . . . . . . . . . . . . . . . . 10
Installing the VersaRails Assemblies
. . . . . . . . . . . . . . . . . . . . . . 11
Installing the System in the Rack
. . . . . . . . . . . . . . . . . . . . . . . . 12
Routing Cables
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Replacing the Rack Doors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figures
Figure 1-1. RapidRails Rack Kit Contents . . . . . . . . . . . . . 8
Figure 1-2. VersaRails Rack Kit Contents
. . . . . . . . . . . . . 8
Figure 1-3. One Rack Unit
. . . . . . . . . . . . . . . . . . . . . 9
Figure 1-4. Marking the Vertical Rails
. . . . . . . . . . . . . . 10
Figure 1-5. Installing the RapidRails Assemblies
. . . . . . . . . 11
Figure 1-6. Installing the VersaRails Rail Assemblies
. . . . . . 12
Figure 1-7. Installing the System in the Rack
. . . . . . . . . . . 13
Figure 1-8. Securing the Cables to the Rack
. . . . . . . . . . . 14
4 Contents
Rack Installation Guide 5
Safety Instructions
Use the following safety guidelines to help ensure your own personal safety and to help protect
your system and working environment from potential damage. For complete safety information,
see the
Product Information
Guide
.
SAFETY: Rack Mounting of Systems
Observe the following precautions for rack stability and safety.
Systems are considered to be components in a rack. Thus, "component" refers to any system as well
as to various peripherals or supporting hardware.
CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks
or the front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before
installing systems in a rack could cause the rack to tip over, potentially resulting in bodily injury under
certain circumstances. Therefore, always install the stabilizer(s) before installing components in the
rack.
CAUTION: After installing system/components in a rack, never pull more than one component out of
the rack on its slide assemblies at one time. The weight of more than one extended component could
cause the rack to tip over and injure someone.
NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a rack
cabinet using the customer rack kit when both the rack cabinet and rack kit were designed for your
system. The installation of your system and rack kit in any other rack cabinet has not been
approved by any safety agencies. It is your responsibility to have the final combination of system
and rack kit in a cabinet evaluated for suitability by a certified safety agency. The manufacturer
disclaims all warranties and liability in connection with such combinations.
System rack kits are intended to be installed in an approved rack by trained service
technicians. If you install the kit in any other rack, be sure that the rack meets the
specifications.
Before working on the rack, make sure that the stabilizers are secured to the rack, extended to
the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers
on a single rack or front stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the rack first.
Make sure that the rack is level and stable before extending a component from the rack.
Do not overload the AC power supply branch circuit that provides power to the rack.
The total rack load should not exceed 80 percent of the branch circuit rating.
Ensure that proper airflow is provided to components in the rack.
Do not step on or stand on any system/component when servicing other systems/components
in a rack.
6 Rack Installation Guide
Installation Instructions
This installation guide provides instructions for trained service technicians installing one or more
systems in an open-frame relay rack or in a rack cabinet. The RapidRails™ rack kit can be installed
without tools in manufacturer’s rack cabinets that have square holes; the VersaRails™ rack kit can
be installed in most industry-standard rack cabinets that have square or round holes. The
procedures for installing both RapidRails and VersaRails rack kits are similar. One rack kit is
required for each system installed in the rack.
CAUTION: Do not install rack kit components designed for another system. Use only the rack kit for
your system. Using the rack kit for another system may result in damage to the system and personal
injury.
The VersaRails rack kit can be installed in most industry-standard rack cabinets.
NOTICE: The VersaRails rack kit is intended to be installed by trained service technicians in a rack that
meets the specifications of American National Standards Institute (ANSI)/Electronic Industries
Association (EIA) standard ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and
Deutsche Industrie Norm (DIN) 41494. One rack kit is required for each system that is installed in a rack.
Before You Begin
Before you begin installing your system in the rack, carefully read "Safety Instructions," found
earlier in this guide, as well as the safety instructions found in your
Product Information Guide
for
additional information.
CAUTION: When installing multiple systems in a rack, complete all of the procedures for the current
system before attempting to install the next system.
CAUTION: Rack cabinets can be extremely heavy and move easily on the casters. The cabinet has no
brakes. Use extreme caution while moving the rack cabinet. Retract the leveling feet when relocating
the rack cabinet. Avoid long or steep inclines or ramps where loss of cabinet control may occur. Extend
the leveling feet for support and to prevent the cabinet from rolling.
Important Safety Information
Observe the safety precautions in the following subsections when installing your system in the rack.
CAUTION: You must strictly follow the procedures in this document to protect yourself as well as
others who may be involved. Your system may be very large and heavy, and proper preparation and
planning are important to prevent injury to yourself and to others. This becomes increasingly important
when systems are installed high up in the rack.
Rack Stabilizer Feet
CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks
or the front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before
installing systems in a rack could cause the rack to tip over, potentially resulting in bodily injury under
certain circumstances. Therefore, always install the stabilizer(s) before installing components in the
rack.
Rack Installation Guide 7
CAUTION: After installing systems in a rack, never pull more than one system out of the rack on its
slide assemblies at one time. The weight of more than one extended system could cause the rack
to tip over and cause injury.
The stabilizer feet help prevent the rack from tipping over when a system or other component is
pulled out of the rack with the slide assemblies fully extended. See the documentation provided
with the rack cabinet for instructions on installing and anchoring the stabilizer feet.
Installation Tasks
Installing a rack kit involves performing the following tasks in their numbered order:
1
Removing the rack doors
2
Marking the rack (if necessary)
3
Installing the rail assemblies in the rack:
RapidRails installation
VersaRails installation
4
Installing the system in the rack
5
Routing cables
6
Replacing the rack doors
Recommended Tools and Supplies
A #2 Phillips screwdriver
Masking tape or a felt-tip pen, for use in marking the mounting holes to be used
A measuring ruler or tape measure
RapidRails Rack Kit Contents
The RapidRails rack kit includes the following items (see Figure 1-1):
One pair of RapidRails assemblies
Four reusable tie wraps
8 Rack Installation Guide
Figure 1-1. RapidRails Rack Kit Contents
VersaRails Rack Kit Contents
The VersaRails rack kit includes the following items (see Figure 1-2):
One pair of VersaRails assemblies
Four reusable tie wraps
Twelve 10-32 x 0.5-inch flange-head Phillips screws
NOTE: Nonmetric screws are identified in this document by size and number of threads per inch.
For example, a #10 Phillips-head screw with 32 threads per inch is identified as a 10-32 screw.
Figure 1-2. VersaRails Rack Kit Contents
RapidRails assemblies
tie-wraps (4)
10-32 x 0.5-inch flange-
head Phillips screws (12)
VersaRails assemblies
tie-wraps (4)
Rack Installation Guide 9
Removing the Rack Doors
See the procedures for removing doors in the documentation provided with your rack cabinet.
CAUTION: Because of the size and weight of the rack cabinet doors, never attempt to remove or install
them by yourself.
CAUTION: Store the two doors where they will not injure someone if the doors accidently fall over.
Marking the Rack
You must allow 7 U (31.1 cm or 12.25 inches) of vertical space for each system you install
in the rack (see Figure 1-3).
NOTE: Your rack may already be marked and not require this procedure.
CAUTION: If you are installing more than one system, install the rail assemblies so that the first system
is installed in the lowest available position in the rack.
1
Place a mark on the rack’s front vertical rails where you want to locate the bottom
of the system you are installing in the rack cabinet.
The bottom of each 1-U space is at the middle of the narrowest metal area between holes
(marked with a horizontal line on some rack cabinets—see Figure 1-3).
Figure 1-3. One Rack Unit
1 U (44 mm or 1.75 inches)
12.7 mm (0.5 inch)
15.9 mm (0.625 inch)
15.9 mm (0.625 inch)
12.7 mm (0.5 inch)
10 Rack Installation Guide
2
Mark the rack’s front vertical rails with a felt-tipped pen or masking tape approximately 31.1
cm (12.25 inches) above the original mark you made (or count up 21 holes in a rack that
meets EIA-310 standards). (If you counted holes, place a mark just above the top hole.)
This mark or piece of tape indicates where the system’s upper edge will be located on
the vertical rails (see Figure 1-4).
Figure 1-4. Marking the Vertical Rails
Installing the RapidRails Assemblies
1
At the front of the rack cabinet, position one of the RapidRails assemblies so that its
mounting-bracket flange fits in the appropriate location on the rack (see Figure 1-5).
The lower mounting hook on the rail assembly’s front-mounting bracket flange should enter
the third hole up from the bottom mark on the vertical rails.
2
Push the rail assembly forward until the top mounting hook enters the square hole just below
the upper marks or tape you placed on the vertical rail. Next, push down on the mounting-
bracket flange until the mounting hooks seat in the square holes and the push button pops
out and clicks (see Figure 1-5).
tape on vertical rail
Rack Installation Guide 11
3
At the back of the cabinet, pull back on the mounting-bracket flange until the mounting
hooks are in the appropriate holes, and then push down on the flange until the mounting
hooks seat in the square holes and the push button pops out and clicks.
4
Repeat steps 1 through 3 for the rail assembly on the other side of the rack.
NOTE: Ensure that the rails are mounted at the same vertical position on both sides of the rack.
Figure 1-5. Installing the RapidRails Assemblies
Installing the VersaRails Assemblies
1
At the front of the rack cabinet, place a VersaRails assembly so that its mounting-bracket
flange fits between the marks or tape (or numbered location) on the rack (see Figure 1-6).
The holes on the front of the mounting bracket should align with the holes between
the marks on the front vertical rail.
2
Install three 10-32 x 0.5-inch flange-head Phillips screws to secure the rail assembly
to the front vertical rail (see Figure 1-6).
rail-assembly mounting-bracket flange
push button
front of rack
rail assemblies (2)
mounting hooks (2)
12 Rack Installation Guide
3
At the back of the cabinet, pull back on the mounting-bracket flange until the mounting
holes align with their respective holes on the back vertical rail.
4
Install three 10-32 x 0.5-inch flange-head Phillips screws in the back mounting flange
to secure the rail assembly to the back vertical rail.
5
Repeat steps 1 through 4 for the rail assembly on the other side of the rack.
NOTE: Ensure that the rails are mounted at the same vertical position on both sides of the rack.
Figure 1-6. Installing the VersaRails Rail Assemblies
Installing the System in the Rack
CAUTION: If you are installing more than one system, install the first system in the lowest available
position in the rack.
CAUTION: Never pull more than one component out of the rack at a time.
CAUTION: Because of the size and weight of the system, never attempt to install the system in the rack
by yourself.
rail assembly
mounting-bracket
flange
front of rack
rail assemblies (2)
flange-head
Phillips screws (3)
vertical rail
Rack Installation Guide 13
CAUTION: It is recommended that more than one person assist in lifting the system.
NOTICE: It is recommended that you use a lift table to aid in installing the system in the rack, particularly
if the rail assemblies are more than waist-high.
1
Lift the system into position to install it in the rack.
It is recommended that more than one person assist in lifting the system.
2
Guide the system into the rack and lower the system onto the rail assemblies (see Figure 1-7).
3
Tighten the thumbscrews on the rack front panel.
Figure 1-7. Installing the System in the Rack
Routing Cables
1
Attach the I/O cable connectors and power cables to their respective connectors on the
system back panel. For details on cable connections, see your system’s
Getting Started Guide
,
Installation and Troubleshooting Guide
, and
User’s Guide
.
NOTE: Use the strain-relief loops (if available) on the back of the power supplies to provide strain
relief for the power cables.
rail assemblies (2)
thumbscrews (4)
14 Rack Installation Guide
2 Using the following guidelines, secure the cables to the rack’s back vertical rails using
the four releasable tie-wraps supplied in the rack kit (see Figure 1-8).
To improve serviceability and airflow, create two bundles of cables on each side of the
system, keeping the area directly in back of the system as clear of cables as possible.
Create separate bundles of cables for the I/O cables and the power cables.
If the cables are sufficiently flexible, leave 10–15 cm (4–6 inches) of slack in the cables
between the cable tie and the system, to improve serviceability of the modules.
Figure 1-8. Securing the Cables to the Rack
Replacing the Rack Doors
See the procedures for replacing doors in the documentation provided with your rack cabinets.
This completes the rack installation of your system.
tie-wraps (4)
cables
vertical rail
I/O cables
power cables
Index 15
Index
C
cable routing, 13
D
doors
removing, 9
replacing, 14
I
installing
system in the rack, 12
K
kit contents
RapidRails, 7
VersaRails, 8
M
marking the rack, 9
R
rack
marking, 9
rack mount precautions, 6
rack stabilizer feet, 6
RapidRails kit contents, 7
routing cables, 13
S
safety instructions, 5
T
tools and supplies
four-post kits, 7
V
VersaRails
kit contents, 8
16 Index
16 Index
Guide d'installation du rack
Remarques, avis et précautions
REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser
votre ordinateur.
AVIS : un AVIS vous avertit d'un risque de dommage matériel ou de perte de données et vous indique comment éviter
le problème.
PRÉCAUTION : une PRÉCAUTION indique un risque potentiel d'endommagement du matériel, de blessure corporelle
ou de mort.
____________________
Les informations contenues dans ce document peuvent être modifiées sans préavis.
© 2005 Dell Inc. Tous droits réservés.
La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc. est strictement interdite.
Marques utilisées dans ce document : RapidRails et VersaRails sont des marques de Dell Inc.
Tous les autres noms de marques et marques commerciales utilisés dans ce document se rapportent aux sociétés propriétaires des marques et
des noms de ces produits. Dell Inc. décline tout intérêt dans l'utilisation des marques déposées et des noms de marques ne lui appartenant pas.
Juillet 2005 P/N F3159 Rev. A01
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88

Dell PowerEdge 1955 クイックスタートガイド

カテゴリー
ラックアクセサリー
タイプ
クイックスタートガイド