2
TT40 LED controller is designed to drive constant
voltage RGB+White color LED products in voltage range of
DC12-24V. It can be controlled by smart phone with Tuya
smart app connection or by the stand alone RF remote
controller. User can setup LED brightness, color, scene
and dynamic effects with the rich function on smart phone
Tuya app or the easy operation remote controller.
1. Power supply input
Connect positive power to the cable marked with ‘+’
and negative to the cable marked with ‘-’. The controller
can accept DC power from 12V to 24V, the output is PWM
driving signal with same voltage level as the power supply,
so please make sure the LED rated voltage is same as the
power supply.
2. LED output
Connect to constant voltage type LED load. Connect
the LED to black cable, and R, G, B, W cable to the
relevant color . Please make sure the LED rated
voltage is same as the power supply and the maximum
load current is below the controller rated current.
CAUTION! The controller will be permanently
damaged if output cables short circuited. Please ensure
the cables are well insulated to each other.
Introduction
Functions
To 110/230
AC power
12-24V DC output
Power supply
TT40 LED
Controller
12-24V DC
LED Strips
LED Controller
12-24V Driving
4. Wiring diagram
3. Work status indicator (optional)
This indicator shows all working status of the
controller. It displays different events as following:
Steady on: Remote and Tuya smart mode.
Flash twice: Tuya not connected.
Flash 3 times: Over heat protection.
Blink: New command received.
Long single blink: Brightness or speed reach limit.
Model: TT40 (W/Z/B)
Terminal & Size
20.5mm
60mm
1 2
3
8
12
11
5
69
7
EFFECTEFFECT
Pair new
remote
Reset to
factory
Press in 10
seconds once
receiver powered
10
5. Turn ON / OFF
Press ‘I’ key to turn on unit or press ‘O’ key to turn off.
The power on status can be set to last status or default
status from app. At last status mode, the controller will
memorize the on/off status and will restore to the
previous status on next power on.
6. Light mode switch
Press this key to switch between RGB, white and
RGB+White mode. In RGB mode, white channel will be
disabled; In white mode, RGB channel will be disabled; In
RGB+White mode, all channels are usable.
Smart & Remote Control
RGB+W LED Controller
High Power
Compact Size 12V/24V voltage
Overheat Protection
Wireless Remote
Tuya Smart Wireless Remote
Tuya Smart
Specification
12. Remote indicator
13. Using the remote controller
Please pull out the battery insulate tape before using.
The RF wireless remote signal can pass through some
nonmetal barrier. For proper receiving remote signal,
please do not install the controller in closed metal parts.
Operation
9. White brightness control
Press key to increase white LED brightness and
press key to decrease.
10. RGB brightness control
Press key to increase RGB LED brightness and
press key to decrease.
11. RGB dynamic effect
Control the RGB dynamic effects. Press and
to select dynamic effects and press and key to
set the running speed of the dynamic effects.
EFFECT EFFECT
8. Shortcut color select
Shortcut key to static colors. LED will run the
relevant color when pressing the specific color key. The
shortcut color is included in and content.
15. Pair a new remote controller
16. Reset to factory default
Model
TT40(W/Z/B)
Output Mode
PWM constant voltage
Working voltage
DC 12-24V
Rated output current
4x2A
Tuya connection
W: Wifi; Z: Zigbee; B: Bluetooth
PWM grade
4000 steps
Overheat protection
Yes
Remote frequency
433.92MHz
Remote control distance
>15m at open area
Overheat protection
Yes
Controller dimension
60x20.5x9mm
Remote dimension
86.5x36x8mm
This indicator blinks when remote controller working.
Please check the remote battery if the indicator does not
light up or flash slowly. The battery type is CR2032.
7
7. Select static RGB color
Press and key to select color from the
preset library colors.
14. Setup Tuya connection
Please install the Tuya app to setup the connection.
Before setup, please make sure the controller is at factory
default mode and not connected to any gateway or router.
The controller has overheat protection feature and it
can protect itself from damage caused by some abnormal
usage such as overloading which generates excess heat.
At overheat situation, the controller will shutdown the
output for a short while and recover when temperature
drops to a safe range.
Please check the output current and make sure it’s
under rated level at this situation.
Overheat Protection
The remote controller and receiver is 1 to 1 paired as
factory default. It’s possible to pair maximum 5 remote
controllers to one receiver and each remote controller
can be paired to any receivers.
To pair a new remote controller, please follow two
steps:
1). Plug off the power of the controller and plug in
again after more than 5 seconds.
2). Within 10 seconds after controller powered on,
press and key simultaneously for about 3
seconds.
After this operation, the LED lights will flash 3 times
to acknowledge that remote pairing is accomplished.
To reset the controller’s Tuya setting and unpair all
remote controllers, please operate with following two
steps:
1). Plug off the power of controller and plug in again
after more than 5 seconds.
2). Press and key simultaneously for about 3
seconds, within 10 seconds after the receiver powered
on.
After this operation, the controller will be reset to
factory default, the Tuya configuration and remote
pairing will all be reset.
2
TT40RGB+WLED控制器是设计⽤于驱动电压范
围为DC12-24V的恒压LED产品。⽤⼾可以通过涂鸦智
能app或者卡⽚式射频遥控器来调节LED灯具。⽤⼾可
以通过涂鸦智能app的功能调节LED灯具的亮度、场景
和动态模式，也可以通过操作遥控器来调节LED灯具的
亮度、颜⾊和动态模式。
简介
Model: TT40 (W/Z/B)
20.5mm
60mm
1 2
3
8
12
11
5
69
7
EFFECTEFFECT
10
接线与尺⼨
2.LED输出 功能
配对新遥控
恢复出⼚
设置
控制器
通电后
10秒内按下
6.模式调节
按此键可以⾃动切换单⽩光模式、RGB模式和
RGB加⽩光模式。在单RGB动态模式下，仅能调节
RGB功能；在单⽩光模式下，仅能调节⽩光的亮度；在
RGB加⽩光模式下，RGB的颜⾊和亮度以及⽩光的亮度
均可以独⽴调节。需注意在RGB动态模式下，单⽩光模
式处于关闭状态。
5.开关
按“I”键开启灯光，按“O”键关闭。控制器会记忆断电
前的开关状态，如果在断电前为关机状态，下次通电后
请使⽤遥控器或者涂鸦智能app开灯。
RGB+WLED控制器
涂鸦智能⽆线
高功率
小尺寸 12-24V电压
过热保护
无线遥控
涂鸦智能
1.电源输⼊
连接到电源。控制器可接受电压为12V到24V的直流
电源供电，请将电源正极连接到标有“+”电缆上，电源负
极连接到标有“-”电缆上。请确保LED灯具的额定电压
与电源电压相同，且电源的功率满⾜控制器和灯具的需
求。
为保证安全，在通电前请先确保所有电缆均已可靠
连接且绝缘良好。
连接到LED灯具。请将LED灯具正极连接到⿊⾊电缆
上，LED灯具对应颜⾊的电缆分别连接到⽩、绿、红、蓝
电缆上，请确保LED的额定电压与电源相同，并且每个
通道的最⼤负载电流在控制器的额定电流范围内。
请注意！如果控制器输出电缆被意外短路，可能将导
致控制器严重损坏，请确保电缆可靠连接并良好绝缘。
该指⽰灯显⽰控制器的⼯作状态，指⽰灯与控制器
⼯作状态和对应关系如下：
常亮：遥控和智能模式
闪烁2次：遥控模式，涂鸦智能未连接
闪烁3次：过热保护
闪烁：收到命令
慢闪：达到亮度或速度极限
4.接线图解
接交流电 12-24V
直流电源
TT40
LED控制器
12-24V DC
LED恒压灯具
3.状态指⽰灯(可选)
控制器
规格
型号
TT40(-W/Z/B)
输出⽅式
PWM恒压
⼯作电压
DC12-24V
额定输出电流
3x3A
涂鸦连接
W:Wifi;Z:Zigbee;B:Bluetooth
遥控器⼯作频率
433.92MHz
遥控器⼯作距离
空旷范围>15⽶
PWM分辨率
4000级
过热保护
有
控制器尺⼨
60x20.5x9mm
遥控器尺⼨
86.5x36x8mm
8.颜⾊快捷键
按下相应颜⾊快捷键时，LED灯具会跳转成相应的
颜⾊。预设的颜⾊库中已包含快捷键所对应的颜⾊。
12.遥控器指⽰灯
按下遥控器按键时，该指⽰灯会快速闪烁。如果指⽰
灯慢闪，则说明遥控器电池电量已耗尽，请更换遥控器
电池（CR2032型纽扣电池）。
13.使⽤遥控器
使⽤前请拔出遥控器电池绝缘⽚。RF⽆线遥控信号
可以穿过⼀定的⾮⾦属屏障，为了保证控制器的接收效
果，请勿将控制器安装在有⼤⾯积⾦属遮挡的位置。
操作⽅法
按以下两个步骤操作，即可将涂鸦智能连接恢复到
出⼚状态，同时已配对的遥控器也会被清除。
1）断开控制器电源，并在超过5秒后重新通电。
2）在控制器通电后的10秒内，同时按下遥控器的
和键约3秒钟。
操作完成后，控制器将恢复成出⼚状态，需要重新配
置智能连接以及重新配对遥控器。
遥控器和控制器出⼚默认为1对1的配对状态。1个控
制器最多可配对5个遥控器，⽽遥控器可配对到任意的
控如需配对新遥控器，请按以下两个步骤操作：
1）断开控制器电源，并在超过5秒后重新通电。
2）在控制器通电后的10秒内，同时按下新遥控器的
和键约3秒钟。
配对成功后，LED灯具将快速闪烁提⽰配对成功。
14.连接涂鸦智能app
请通过安装并设置涂鸦智能app来进⾏连接。在设
置连接前，请确保控制器是处于出⼚默认模式状态，且
没有连接任何⽹关或路由器。
15.与新遥控器配对
16.恢复出⼚设置
7
7.静态RGB颜⾊调节
按与可以从预设的颜⾊库中调节颜⾊。
9.单⽩光亮度调节
按键增加单⽩光亮度，按键降低单⽩光亮度。
按键增加RGB亮度，按键降低RGB亮度。
11.RGB动态模式调节
按和调节RGB动态模式，按和
调节RGB动态模式的运⾏速度。
EFFECT EFFECT
过热保护
本机具有过热保护功能，可防⽌控制器因负载过
重引起异常发热⽽导致损坏。过热保护时控制器将关
断输出，当温度下降到安全范围时，将尝试恢复正常
⼯作。过热保护功能仅能在⼀定程度上防⽌控制器损
坏，为确保安全，请勿将控制器输出过载或短路。
/