Sonicare HX6877/27 ユーザーマニュアル

ProtectiveClean

6500/6100

1

2

11

4

3

5

6

7

8

9

10

empty page before TOC

English 6

简体中文 18

繁體中文 35

English

6English

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

Danger

- Keep the charger away from water. Do not place or

store it over or near water contained in a bathtub,

washbasin, sink etc. Do not immerse the charger in

water or any other liquid. After cleaning, make sure

the charger is completely dry before you connect it to

the wall socket.

Warning

- The mains cord cannot be replaced. If the mains cord

is damaged, discard the charger.

- Always have the charger replaced with one of the

original type in order to avoid a hazard.

- Do not use the charger outdoors or near heated

surfaces.

- If the appliance is damaged in any way (brush head,

toothbrush handle or charger), stop using it. This

appliance contains no serviceable parts. If the

appliance is damaged, contact the Consumer Care

Center in your country (see chapter 'Warranty and

support').

- This appliance can be used by children and persons

with reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they have

been given supervision or instruction concerning use

of the appliance in a safe way and understand the

hazards involved. Cleaning and user maintenance

shall not be made by children without supervision.

- Children shall not play with the appliance.

Caution

- Do not clean the brush head, the handle or the

charger in the dishwasher.

- If you have had oral or gum surgery in the previous 2

months, consult your dentist before you use the

toothbrush.

7

English

- Consult your dentist if excessive bleeding occurs after

using this toothbrush or if bleeding continues to occur

after 1 week of use. Also consult your dentist if you

experience discomfort or pain when you use the

Philips Sonicare.

- The Philips Sonicare toothbrush complies with the

safety standards for electromagnetic devices. If you

have a pacemaker or other implanted device, contact

your physician or the device manufacturer of the

implanted device prior to use.

- If you have medical concerns, consult your doctor

before you use the Philips Sonicare.

- This appliance has only been designed for cleaning

teeth, gums and tongue. Do not use it for any other

purpose. Stop using the appliance and contact your

doctor if you experience any discomfort or pain.

- The Philips Sonicare toothbrush is a personal care

device and is not intended for use on multiple

patients in a dental practice or institution.

- Stop using a brush head with crushed or bent bristles.

Replace the brush head every 3 months or sooner if

signs of wear appear. Do not use other brush heads

than the ones recommended by the manufacturer.

- If your toothpaste contains peroxide, baking soda or

bicarbonate (common in whitening toothpastes),

thoroughly clean the brush head with soap and water

after each use. This prevents possible cracking of the

plastic.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable

standards and regulations regarding exposure to

electromagnetic fields.

Radio Equipment Directive

- Radio Equipment in this product operates at 13.56

MHz

- Maximum RF power transmitted by the Radio

Equipment is 30.16dBm

8English

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benefit from the support that Philips

offers, register your product at

www.philips.com/welcome.

Your Philips Sonicare (Fig. 1)

1 Hygienic travel cap

2 Smart brush head(s)*

3 Handle

4 Power on/off button

5 Intensity light

6 Mode/intensity button

7 Mode light

8 Brush head replacement reminder light

9 Battery indication

10 Charging base

11 Travel case (specific types only)*

*Note: The content of the box may vary based on the

model purchased.

Brush heads

Your Philips Sonicare comes with one or more brush

heads which are designed to deliver superior results for

your oral care needs.

Philips Sonicare BrushSync Technology

Your brush head(s) are enabled with BrushSync

technology. This technology enables 2 features with this

toothbrush:

1Brush head mode pairing (see 'Features and

Accessories')

2Brush head replacement reminder (see 'Features and

Accessories')

This symbol indicates the brush head is equipped with

BrushSync technology. (Fig. )

Brushing modes

Your power toothbrush is equipped with 3 different

modes to accommodate all your oral care needs.

9

English

To change modes, press the mode/intensity button while

the toothbrush is off.

The following modes are available:

Clean mode

Clean is a 2-minute mode, recommended to be used with

intensity level 3. It gives you a thorough and complete

clean and is recommended to be used with the C2

Optimal Plaque Control brush head.

White mode

White is a 2-minute 30-seconds mode, recommended to

be used with intensity level 3 and the W2 Optimal White

brush head.

Gum Care mode

Gum Care is a 3-minute mode, recommended to be used

with intensity level 3 and the G2 Optimal Gum Care brush

head.

Intensity settings

Your power toothbrush gives you the option to choose

between 3 different intensity levels: low, medium and

high. (Fig. ) Based on the brush head you attach, the

intensity will be selected. The intensity can be changed by

pressing the mode/intensity button while brushing. For

optimal results it is recommended to use the

automatically selected intensity. The intensity cannot be

changed as long as the handle is powered off or paused.

Using your Philips Sonicare

Brushing instructions

1Press the brush head onto the handle in such a way

that the bristles will face the front of the handle. (Fig. )

2Firmly press the brush head down onto the metal

shaft until it stops.

Note: It is normal to see a slight gap between the

brush head and the handle.

3Wet the bristles. (Fig. )

10 English

4Apply a small amount of toothpaste on the bristles.

(Fig. )

5Place the toothbrush bristles against the teeth at a

slight angle (45 degrees), pressing firmly to make the

bristles reach the gumline or slightly beneath the

gumline. (Fig. )

Note: A change in vibration (and a slight change in

sound) alerts you when you apply too much pressure

while brushing.

Note: Keep the center of the brush in contact with the

teeth at all times.

6Press the power on/off button to turn on the Philips

Sonicare. (Fig. )

7Gently keep the bristles placed on the teeth and in the

gumline. Brush your teeth with small back and forth

motion so the bristles reach between the teeth. (Fig. )

Note: The bristles should slightly flare. Do not scrub.

8To clean the inside surfaces of the front teeth, tilt the

brush handle semi-upright and make several vertical

overlapping brushing strokes on each tooth. (Fig. )

9To make sure you brush evenly throughout the

mouth, divide the mouth into 4 sections using the

Quadpacer feature. (Fig. ) The quadpacer feature

beeps after 30 seconds.

10 Brush for the full 2 minutes following the Quadpacer.

(Fig. ) After 2 minutes, the toothbrush will

automatically shut off.

In white mode, after 2 minutes the handle will

continue to brush for 30 seconds so that you can

brighten and polish your front teeth. During the

extra time, the Quadpacer beeps every 15 seconds.

In gum care mode, after 2 minutes the handle will

continue to brush for an additional minute so you

can gently stimulate and massage your gums.

During the extra time, the Quadpacer beeps every

15 seconds.

- After you have completed the brushing cycle, you can

spend additional time brushing the chewing surfaces

of your teeth and areas where staining occurs. (Fig. )

11

English

Note: Your Philips Sonicare toothbrush is safe to use

on:

- Braces (brush heads wear out sooner when used on

braces)

- Dental restorations (fillings, crowns, veneers)

Note: When the Philips Sonicare toothbrush is used in

clinical studies, it must be used in the Clean mode (for

plaque and gum health claims) or in White mode (for

whitening claims) at high intensity with EasyStart

turned off.

Features

- EasyStart

- Brush head replacement reminder

- Pressure sensor

- Brush head mode pairing

- Quadpacer

Easy-start

This Philips Sonicare model comes with the EasyStart

feature deactivated. The EasyStart feature gently

increases the power over the first 14 brushings to help

you get used to the brushing with the Philips Sonicare.

The EasyStart feature works in all modes.

To activate EasyStart see 'Activating or deactivating

features'.

Brush head replacement reminder

Your Philips Sonicare is equipped with BrushSync

technology that tracks the wear of your brush head. (Fig.

)

1When attaching a new smart brush head for the first

time the brush head replacement reminder light

blinks green three times. This confirms you have a

Philips brush head with BrushSync technology.

12 English

2Over time, based on the pressure you apply and the

amount of time used, the handle will track brush head

wear in order to determine the optimal time to

change your brush head. This feature gives you the

guarantee for the best cleaning and care of your

teeth.

3When the brush head replacement reminder light

lights up amber, you should replace your brush head.

To deactivate the brush head replacement reminder see

'Activating or deactivating features'.

Pressure sensor

Your Philips Sonicare is equipped with an advanced

sensor that measures the pressure you apply while

brushing. If you apply too much pressure, the toothbrush

will provide immediate feedback to indicate that you

need to reduce the pressure. This feedback is given by a

change in vibration and therefore brushing sensation.

To deactivate the pressure sensor see 'Activating or

deactivating features'.

Brush head mode pairing

An RFID chip inside the brush head communicates with

the toothbrush handle. When you attach a brush head,

the handle automatically recognizes the brush head and

selects the right mode and intensity level to optimize

your brushing performance.

Quadpacer

The Quadpacer is an interval timer that has a short beep

and pause to remind you to brush the different sections

of your mouth. Depending on the brushing mode you

have selected (see 'Brushing modes'), the Quadpacer

beeps at different intervals during the brushing cycle.

Activating or deactivating features

You can activate or deactivate the following features of

your toothbrush:

- EasyStart

- Brush head replacement reminder

- Pressure sensor

13

English

To activate or deactivate these features, follow the

instructions below:

EasyStart

1Put the handle on the plugged-in charger.

2Press and hold the power on/off button while the

handle remains on the charger.

3Keep the power on/off button pressed until you hear

a single short beep (after 2 seconds).

4Release the power on/off button.

- Triple tone of low-med-high means the EasyStart

feature has been activated. The brush head

replacement light and battery light will also blink

green 2 times in unison to confirm activation.

- Triple tone of high-med-low means the EasyStart

feature has been deactivated. The brush head

replacement light and battery light will also blink

amber 2 times in unison to confirm deactivation.

Note: To achieve clinical efficacy, EasyStart needs to be

deactivated.

Brush head replacement reminder

1Put the handle on the plugged-in charger.

2Press and hold the power on/off button while the

handle remains on the charger.

3Keep the power on/off button pressed until you hear

a series of two short beeps (after 4-5 seconds).

4Release the power on/off button.

- Triple tone of low-med-high means the Brush

head replacement reminder feature has been

activated. The brush head replacement light and

battery light will also blink green 2 times in unison

to confirm activation.

- Triple tone of high-med-low means the Brush

head replacement reminder feature has been

deactivated. The brush head replacement light

and battery light will also blink amber 2 times in

unison to confirm deactivation.

Pressure sensor

1Put the handle on the plugged-in charger.

14 English

2Press and hold the power on/off button while the

handle remains on the charger.

3Keep the power on/off button pressed until you hear

a series of three short beeps (after 6-7 seconds).

4Release the power on/off button.

- Triple tone of low-med-high means the pressure

sensor feature has been activated. The brush head

replacement light and battery light will also blink

green 2 times in unison to confirm activation.

- Triple tone of high-med-low means the pressure

sensor feature has been deactivated. The brush

head replacement light and battery light will also

blink amber 1 time in unison to confirm

deactivation.

If you continue holding the power on/off button after

the three short beeps, the activate/deactivate sequence

repeats.

Battery status and charging

1Put the plug of the charger in an electrical outlet.

2Place the handle on the charger.

- The charger will emit 2 short beeps to confirm that

the handle is placed properly.

- The flashing light of the battery level indicator

shows that the toothbrush is charging.

- When handle is fully charged on the charger, the

battery light shows solid green for 30 seconds and

switches off.

Note: Your toothbrush comes pre-charged for first use.

After first use, charge for at least 24 hours.

Battery status (when handle is not on charger)

When removing the Philips Sonicare from the charger,

the battery light at the bottom of the toothbrush will

indicate the status of the battery life.

- Solid green LED: full battery

- Flashing green LED: medium battery

- Flashing amber LED and three beeps: low battery

15

English

- Flashing amber LED and two sets of five beeps: No

brushing sessions left (charge toothbrush)

Cleaning

Note: Do not clean the brush head, handle or travel case

in the dishwasher.

Toothbrush handle

1Remove the brush head and rinse the metal shaft area

with warm water. Make sure you remove any residual

toothpaste (Fig. ).

Note: Do not push on the rubber seal on the metal

shaft with sharp objects, as this may cause damage.

2Wipe the entire surface of the handle with a damp

cloth.

Note: Do not use isopropyl rubbing alcohol, vinegar or

bleach to clean handle as this may cause

discoloration.

Brush head

1Rinse the brush head and bristles after each use (Fig. ).

2Remove the brush head from the handle and rinse the

brush head connection with warm water at least once

a week.

Charger

1Unplug the charger before you clean it.

2Wipe the surface of the charger with a damp cloth.

Make sure you remove any toothpaste or other

residue from the charger surfaces.

Storage

If you are not going to use your Philips Sonicare for an

extended period of time, unplug the charger from the

wall socket, clean it and store it in a cool and dry place

away from direct sunlight.

Locating the model number

Look on the bottom of the Philips Sonicare toothbrush

handle for the model number (HX684x/HX685x).

16 English

Recycling

- Do not throw away the product with the normal

household waste at the end of its life, but hand it in at

an official collection point for recycling. By doing this,

you help to preserve the environment.

- This product contains a built-in rechargeable battery

which shall not be disposed of with normal household

waste. Please take your product to an official

collection point or a Philips service center to have a

professional remove the rechargeable battery.

- Follow your country’s rules for the separate collection

of electrical and electronic products and rechargeable

batteries. Correct disposal helps prevent negative

consequences for the environment and human

health.

Removing the rechargeable battery

Warning: Only remove the rechargeable battery when

you discard the appliance. Make sure the battery is

completely empty when you remove it.

To remove the rechargeable battery, you need a towel or

cloth, a hammer and a flat-head (standard) screwdriver.

Observe basic safety precautions when you follow the

procedure outlined below. Be sure to protect your eyes,

hands, fingers, and the surface on which you work.

1To deplete the rechargeable battery of any charge,

remove the handle from the charger, turn on the

Philips Sonicare and let it run until it stops. Repeat this

step until you can no longer turn on the Philips

Sonicare.

2Remove and discard the brush head. Cover the entire

handle with a towel or cloth (Fig. ).

3Hold the top of the handle with one hand and strike

the handle housing 0.5 inch above the bottom end.

Strike firmly with a hammer on all 4 sides to eject the

end cap (Fig. ).

Note: You may have to hit on the end several times to

break the internal snap connections.

4Remove the end cap from the toothbrush handle. If

the end cap does not release easily from the housing,

repeat step 3 until the end cap is released (Fig. ).

17

English

5Holding the handle upside down, press the shaft

down on a hard surface. If the internal components

do not easily release from the housing, repeat step 3

until the internal components are released (Fig. ).

6Remove the rubber battery cover.

7Wedge the screwdriver between the battery and the

black frame at the bottom of the internal

components. Then pry the screwdriver away from the

battery to break the bottom of the black frame (Fig. ).

8Insert the screwdriver between the bottom of the

battery and the black frame to break the metal tab

connecting the battery to the green printed circuit

board. This will release the bottom end of the battery

from the frame (Fig. ).

9Grab the battery and pull it away from the internal

components to break the second metal battery tab

(Fig. ).

Caution: Be aware of the sharp edges of the

battery tabs so as to avoid injury to your fingers.

10 Cover the battery contacts with tape to prevent any

electrical short from residual battery charge. The

rechargeable battery can now be recycled and the

rest of the product discarded appropriately (Fig. ).

Warranty and support

If you need information or support, please visit

www.philips.com/support or read the international

warranty leaflet.

Warranty restrictions

The terms of the international warranty do not cover the

following:

- Brush heads.

- Damage caused by use of unauthorized replacement

parts.

- Damage caused by misuse, abuse, neglect, alterations

or unauthorized repair.

- Normal wear and tear, including chips, scratches,

abrasions, discoloration or fading.

简体中文

18 简体中文

注意事项

使用本产品之前，请仔细阅读本使用说明

书，并妥善保管以备日后参考。

危险

- 使充电器远离水源。切勿将它放置或

存放在任何有水的容器的上方或附

近，如：浴盆、脸盆、水池等。切勿

将充电器浸入水或任何其他液体中。

清洁后，确保充电器完全干燥，再将

其连接至电源。

- 必须安装需要的固定部件，以免它们

掉入水中。

警告

- 不得更换电源线。如果电源线损坏，

请丢弃充电器。

- 应始终使用原装型号的充电器进行更

换，以免发生危险。

- 切勿在户外或高温表面附近使用充电

器。

- 如果本产品受到任何损坏（刷头、牙

刷手柄或充电器），请停止使用。本

产品不包含任何可维修零部件。如果

本产品已损坏，请联系您所在国家/地

区的客户服务中心（请参阅“保修和支

持”一章）。

19

简体中文

- 本产品适合由儿童和肢体不健全、感

觉或精神上有障碍或缺乏相关经验和

知识的人士使用，但前提是有人对他

们使用本产品进行监督或指导，以确

保他们安全使用，并且让他们明白相

关的危害。不要让儿童在无人监督的

情况下对本产品进行清洁和保养。

- 切勿让儿童玩弄本产品。

注意

- 请勿在洗碗机中清洗牙刷头、牙刷柄

或充电器。

- 如果您在前 2 个月中曾做过口腔或牙

龈手术，请在使用本产品前先咨询您

的牙医。

- 如果使用本产品后牙龈大量出血或在

使用 1 周后仍会出血，请咨询您的牙

医。如果使用飞利浦 Sonicare 时感

觉不适或疼痛，也请咨询您的牙医。

- 飞利浦 Sonicare 牙刷符合电磁装置的

安全标准。有关任何涉及心脏起搏器

或其他植入装置的问题，请在使用之

前咨询医生或相关植入装置的设备制

造商。

- 如果您有医学问题，请在使用飞利浦

Sonicare 前咨询医生。

- 本产品设计仅用于清洁牙齿、牙龈和

舌头。请勿将其用作任何其它用途。

如果感觉任何不适或疼痛，请停止使

用本产品并与医生联系。

20 简体中文

- 飞利浦 Sonicare 牙刷为私人用品，不

可供牙医诊所或机构对多位患者使

用。

- 请停止使用变形或刷毛弯曲的牙刷

头。请每 3 个月更换一次牙刷头，如

果出现磨损迹象，应提前更换。切勿

使用非制造商推荐的其他刷头。

- 如果您所用的牙膏中含有过氧化物、

碳酸氢钠或其它重碳酸盐（增白牙膏

中的常见成份），则请务必在每次使

用后用肥皂和水彻底清洗刷头。这可

以预防可能出现的塑料破裂。

电磁场 (EMF)

本飞利浦产品符合所有有关暴露于电磁场

的适用标准和法规。

无线电设备指令

- 本产品中无线电设备的工作频率为

13.56 MHz。

- 无线电设备传输的最大射频功率为

30.16 dBm

说明

感谢您的惠顾，很高兴您选择飞利浦！为

了让您能充分享受飞利浦提供的支持，请

在 www.philips.com/welcome 上注

册您的产品。

飞利浦 Sonicare 声波震动牙刷（图 1）

1 旅行用卫生保护盖

ページを読み込んでいます...

Sonicare HX6877/27, HX6871/42, HX6874/42, HX6897/22 ユーザーマニュアル

関連論文

その他の書類