Saeco HX8911/02 ユーザーマニュアル



Contact Philips
繁體中文 16
简体中文 25
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at
Read this user manual carefully before you use the appliance and save
it for future reference.
- Keep the charger away from water. Do not place or store it over or
near water contained in a bathtub, washbasin, sink etc. Do not
immerse the charger in water or any other liquid. After cleaning, make
sure the charger is completely dry before you connect it to the mains.
- The mains cord cannot be replaced. If the mains cord is damaged,
discard the charger.
- Always have the charger replaced with one of the original type in
order to avoid a hazard.
- Do not use the charger outdoors or near heated surfaces.
- If the appliance is damaged in any way (brush head, toothbrush
handle or charger), stop using it. This appliance contains no
serviceable parts. If the appliance is damaged, contact the Consumer
Care Centre in your country (see chapter ‘Guarantee and support’).
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that they do not play with
the appliance.
- Do not clean the brush head, the handle or the charger in the
- If you have had oral or gum surgery in the previous 2 months,
consult your dentist before you use the toothbrush.
- Consult your dentist if excessive bleeding occurs after using this
toothbrush or if bleeding continues to occur after 1 week of use.
Also consult your dentist if you experience discomfort or pain when
you use the Sonicare.
- The Sonicare toothbrush complies with the safety standards for
electromagnetic devices. If you have a pacemaker or other implanted
device, contact your physician or the device manufacturer of the
implanted device prior to use.
- If you have medical concerns, consult your doctor before you use
the Sonicare.
- This appliance has only been designed for cleaning teeth, gums and
tongue. Do not use it for any other purpose. Stop using the appliance
and contact your doctor if you experience any discomfort or pain.
- The Sonicare toothbrush is a personal care device and is not
intended for use on multiple patients in a dental practice or institution.
- Stop using a brush head with crushed or bent bristles. Replace the
brush head every 3 months or sooner if signs of wear appear. Do not
use other brush heads than the ones recommended by the manufacturer.
- If your toothpaste contains peroxide, baking soda or bicarbonate
(common in whitening toothpastes), thoroughly clean the brush head
with soap and water after each use. This prevents possible cracking of
the plastic.
Electromagnetic elds (EMF)
This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic elds.
General description (Fig. 1)
1 Hygienic travel cap
2 Brush head
3 Handle
4 Power on/off and mode button
5 Intensity level indicator
6 Intensity level button (+ and -)
7 Mode indicator
8 Battery level indicator
9 Charger
Note: The content of the box may vary based on the model purchased.
Preparing for use
Attaching the brush head
1 Align the brush head so the bristles face the front of the handle.
(Fig. 2)
2 Firmly press the brush head down onto the metal shaft until it stops.
Note: Philips Sonicare brush heads are imprinted with icons to easily identify
your brush head.
Charging the appliance
1 Put the plug of the charger in a wall socket.
2 Place the handle on the charger (Fig. 3).
, The ashing light of the battery level indicator indicates that the
toothbrush is charging.
Note: It can take up to 48 hours to fully charge the battery, but the Philips
Sonicare may be used before it is fully charged.
Using the appliance
Brushing instructions
1 Wet the bristles and apply a small amount of toothpaste.
2 Place the toothbrush bristles against the teeth at a slight angle
(45 degrees), pressing rmly to make the bristles reach the gumline
or slightly beneath the gumline. (Fig. 4)
Note: Keep the center of the brush in contact with the teeth at all times.
3 Press the power on/off and mode button to switch on the Philips
4 Apply light pressure to maximise Philips Sonicare’s effectiveness
and let the Philips Sonicare toothbrush do the brushing for you.
Do not scrub.
5 Gently move the brush head slowly across the teeth in a small back
and forth motion so the longer bristles reach between your teeth.
Continue this motion throughout the brushing cycle.
6 To clean the inside surfaces of the front teeth, tilt the brush handle
semi-upright and make several vertical overlapping brushing strokes
on each tooth (Fig. 5).
Note: To make sure you brush evenly throughout the mouth, divide your
mouth into 4 sections using the Quadpacer feature (see chapter ‘Features’).
7 Brush each section for 30 seconds for a total brushing time of
2 minutes. Start with section 1 (outside top teeth) and then brush
section 2 (inside top teeth). Continue with section 3 (outside
bottom teeth) and nally brush section 4 (inside bottom teeth) (Fig. 6).
8 After you have completed the brushing cycle, you can spend
additional time brushing the chewing surfaces of your teeth and
areas where staining occurs. You can also brush your tongue,
with the toothbrush switched on or off, as you prefer (Fig. 7).
The Philips Sonicare is safe to use on:
- Braces (brush heads wear out sooner when used on braces).
- Dental restorations (llings, crowns, veneers)
Note: Ensure that braces or dental restorations are properly adhered and not
compromised. If not, braces or dental restorations may be damaged when
they come into contact with the brush head.
Note: When the Philips Sonicare is used in clinical studies, the default 2-minute
Clean mode with high intensity must be selected. The handle should be fully
charged and the Easy-start feature deactivated.
Brushing modes
Clean mode
The ultimate in plaque removal (default mode).
White mode
To brighten and polish your front teeth.
1 Press the power on/off and mode button to switch on the Philips
2 Press the power on/off and mode button again before 2.5 seconds
to switch to White mode.
3 Press the power on/off and mode button after 2.5 seconds to pause
the Philips Sonicare.
Intensity levels
- Low: 1 LED indicator light
- Medium: 2 LED indicator lights
- High: 3 LED indicator lights
Note: To adjust the intensity level to the next higher or lower level, press
the + intensity level button to increase intensity or the - intensity level button
to decrease intensity at any time during the brushing cycle.
Battery status (when handle is not on charger)
- A ashing yellow battery level indicator indicates a low charge.
- A ashing green battery level indicator indicates a moderate charge.
- A solid green battery level indicator indicates a full charge.
Note: If you hear 5 beeps and the battery level indicator ashes yellow,
this means that you have to recharge the battery. When the battery is
completely empty, the Philips Sonicare switches off. Place the Philips Sonicare
on the charger to charge it (Fig. 3).
Note: To keep the battery fully charged at all times, you may keep the Philips
Sonicare on the charger when not in use.
The Smartimer indicates that your brushing cycle is complete when it
automatically switches off the toothbrush at the end of the brushing cycle.
Dental professionals recommend brushing no less than 2 minutes twice
a day.
- The Easy-start feature gently increases power over the rst
14 brushings to help you get used to brushing with the Philips Sonicare.
- This Philips Sonicare comes with the Easy-start feature deactivated.
Activating or deactivating the Easy-start feature:
Place the handle in the plugged-in charger.
- To activate Easy-start:
Press and hold the power on/off and mode button for 2 seconds.
You hear 2 beeps and the battery level indicator lights up green to
indicate that the Easy-start feature has been activated.
- To deactivate Easy-start:
Press and hold the power on/off and mode button for 2 seconds.
You hear 1 beep and the battery level indicator lights up yellow to
indicate that the Easy-start feature has been deactivated.
Note: Each of the rst 14 brushings must last at least 1 minute to move
through the Easy-start ramp-up cycle properly.
Note: Use of the Easy-start feature beyond the initial ramp-up period is not
recommended and reduces the effectiveness of the Philips Sonicare
toothbrush in removing plaque.
- The Quadpacer is an interval timer that has a short beep and pause
to remind you to brush the 4 sections of your mouth evenly and
thoroughly. Depending on the brushing mode you have selected,
the Quadpacer beeps at different intervals during the brushing
cycle (Fig. 6).
Activating or deactivating the Quadpacer feature:
Place the handle in the plugged-in charger.
- To activate Quadpacer: Press and hold the intensity level button
down (-) for 2 seconds. You hear 2 beeps and the battery level
indicator lights up green to indicate that the Quadpacer feature has
been activated.
- To deactivate Quadpacer: Press and hold the intensity level button
down (-) for 2 seconds. You hear 1 beep and the battery level
indicator lights up yellow to indicate that the Quadpacer feature has
been deactivated.
Charger conrmation
When the charger conrmation feature is activated, the handle beeps and
vibrates briey when it is placed on the charger base. This Philips Sonicare
model comes with the charger conrmation feature deactivated.
Activating or deactivating the charger conrmation
Place the handle on the charger.
- To activate charger conrmation: Press and hold the intensity level
button up (+) for 2 seconds. You hear 2 beeps and the battery level
indicator lights up green twice to indicate that the charger
conrmation feature has been activated.
- To deactivate charger conrmation: Press and hold the intensity level
button up (+) for 2 seconds. You hear 1 beep and the battery level
indicator lights up yellow once to indicate that the charger
conrmation feature has been deactivated.
The Philips Sonicare should be cleaned regularly to remove toothpaste
and other residue. Failure to clean the Philips Sonicare may result in an
unhygienic product and damage to it may occur.
Do not clean brush heads, the handle or the charger in the dishwasher.
Toothbrush handle
1 Remove the brush head and rinse the metal shaft area with warm
water. Make sure you remove any residual toothpaste (Fig. 8).
Do not push on the rubber seal on the metal shaft with sharp objects,
as this may cause damage.
2 Wipe the entire surface of the handle with a damp cloth.
Brush head
1 Rinse the brush head and bristles after each use (Fig. 9).
2 Remove the brush head from the handle and rinse the brush head
connection with warm water at least once a week.
1 Unplug the charger before you clean it.
2 Wipe the surface of the charger with a damp cloth. Make sure you
remove any toothpaste or other residue from the charger surfaces.
If you are not going to use the product for a long time, unplug it, clean it
(see chapter ‘Cleaning’) and store it in a cool and dry place away from
direct sunlight.
Brush head
- Replace Philips Sonicare brush heads every 3 months to achieve
optimal results.
- Use only Philips Sonicare replacement brush heads.
Do not throw away the appliance with the normal household waste at
the end of its life, but hand it in at an ofcial collection point for recycling.
By doing this, you help to preserve the environment.
Removing the rechargeable battery
Only remove the rechargeable battery when you discard the appliance.
Make sure the battery is completely empty when you remove it.
To remove the rechargeable battery, you need a towel or cloth, a
hammer and a at-head (standard) screwdriver. Observe basic safety
precautions when you follow the procedure outlined below. Be sure to
protect your eyes, hands, ngers, and the surface on which you work.
1 To deplete the rechargeable battery of any charge, remove the
handle from the charger, switch on the Philips Sonicare and
let it run until it stops. Repeat this step until you can no longer
switch on the Philips Sonicare.
2 Remove and discard the brush head. Cover the entire handle with
a towel or cloth (Fig. 10).
3 Hold the top of the handle with one hand and strike the handle
housing 1 cm above the bottom end. Strike rmly with a hammer
on all 4 sides to eject the end cap (Fig. 11).
You may have to hit on the end several times to break the
internal snap connections.
4 Remove the end cap from the toothbrush handle. If the end cap
does not release easily from the housing, repeat step 3 until the
end cap is released (Fig. 12).
5 Holding the handle upside down, press the shaft down on a hard
surface. If the internal components do not easily release from the
housing, repeat step 3 until the internal components are released.
(Fig. 13)
6 Remove the rubber battery cover (Fig. 14).
7 Wedge the screwdriver between the battery and the black frame at
the bottom of the internal components. Then pry the screwdriver
away from the battery to break the bottom of the black frame
(Fig. 15).
8 Insert the screwdriver between the bottom of the battery and the
black frame to break the metal tab connecting the battery to the
green printed circuit board. This will release the bottom end of the
battery from the frame (Fig. 16).
9 Grab the battery and pull it away from the internal components to
break the second metal battery tab (Fig. 17).
Be aware of the sharp edges of the battery tabs so as to avoid
injury to your ngers.
10 Cover the battery contacts with tape to prevent any electrical
short from residual battery charge. The rechargeable battery can
now be recycled and the rest of the product discarded appropriately.
Guarantee and support
If you need information or support, please visit
support or read the separate worldwide guarantee leaet.
Guarantee restrictions
The terms of the international guarantee do not cover the following:
- Brush heads.
- Damage caused by use of unauthorised replacement parts.
- Damage caused by misuse, abuse, neglect, alterations or unauthorised
- Normal wear and tear, including chips, scratches, abrasions,
discolouration or fading.
welcome 註冊您的產品,以善用飛利浦提供的支援。
- 請勿讓充電器沾到水。請勿放置或存放於盛水的澡盆、洗臉盆、
- 本電線無法更換。如果電線損壞,請棄置充電器。
- 請務必以原型號的充電器更換,以免發生危險。
- 充電器不可在室外或高熱表面附近使用。
- 本產品 (含刷頭、牙刷握柄或充電器) 若有任何破損跡象,
請與您所在國家/地區的客戶服務中心聯繫 (請參閱「保固與支
- 本產品不適合供下列人士 (包括孩童) 使用:身體官能或心智能
- 請勿讓孩童使用本產品或將本產品當成玩具。
- 請勿將刷頭、握柄或充電器放入洗碗機中清洗。
- 如果您的口腔或牙齦在過去 2 個月內曾動過手術,請在使用本
- 如果您在使用本牙刷後有出血狀況,或者出血狀況持續超過
1 星期,請諮詢您的牙醫。若使用 Sonicare 電動牙刷之後感到
- Sonicare 電動牙刷符合電磁裝置之安全標準。若您身上裝有心
- 若您有醫療方面的顧慮,使用 Sonicare 之前請先諮詢您的醫師。
- 本產品只適用於清潔牙齒、牙齦與舌頭,請勿用作其他用途。
- Sonicare 電動牙刷為個人保健用品,不宜在牙醫診所或醫療機
- 刷頭的刷毛若傾倒彎曲,請停止使用。請每 3 個月更換一次
- 如果牙膏內含過氧化氫、小蘇打或重碳酸鹽 (常見於美白用牙膏),
電磁波 (EMF)
一般說明 (圖 1)
1 旅行用衛生保護蓋
2 刷頭
3 握把
4 電源開關與模式按鈕
5 強度等級指示燈
6 強度等級按鈕(+和-)
7 模式指示燈
8 電池電量指示燈
9 充電器
繁體中文 17
1 將刷頭對齊,使刷毛朝向握柄正面。(圖2)
2 將刷頭用力下壓到金屬軸上,至到底為止。
1 將充電器插頭插入牆上插座。
2 將握柄放到充電器上。(圖3)
, 電池電量指示燈若在閃爍,表示牙刷正在充電中。
1 沾濕刷毛,擠上少量牙膏。
2 將牙刷刷毛略呈傾斜(45度)放置於牙齒表面,用力下壓使刷
3 按下電源開關與模式按鈕,開啟飛利浦Sonicare電源。
4 略為施力即可充分發揮飛利浦Sonicare的效能,將刷牙的工
5 將刷頭以輕柔緩慢的小動作在牙齒表面來回移動,讓較長的刷
6 如要清潔門齒內側表面,請直握牙刷握柄,使其呈半傾斜,
7 清潔每個區域30秒,全口清潔總計為2分鐘的刷牙時間。由第
8 完成刷牙週期後,可多花些時間刷洗牙齒咬合面及齒垢堆積處。
飛利浦 Sonicare 能在以下狀態安全使用:
- 牙齒矯正器 (如果您有裝矯正器,刷頭會較快磨損)。
- 牙齒復型 (填補、牙套、牙面鑲嵌)
最能有效清除牙菌斑 (預設模式)。
1 按下電源開關與模式按鈕,開啟飛利浦Sonicare電源。
2 在2.5秒內再度按下電源開關與模式按鈕,可切換至亮白模式。
3 2.5秒後按下電源開關與模式按鈕,可暫停飛利浦Sonicare。
- :1 個 LED 指示燈
- :2 個 LED 指示燈
- :3 個 LED 指示燈
繁體中文 19
電池狀態 (若握柄不在充電器上)
- 電池電量指示燈閃爍黃燈表示電力不足。
- 電池電量指示燈閃爍綠燈表示電力中等。
- 電池電量指示燈持續亮綠燈表示電力充足。
牙科專家建議,每日應刷牙兩次,每次 2 分鐘以上。
Easy-start 循序漸進功能
- Easy-start 功能在前 14 次的使用中會緩慢增加力道,讓您能逐
漸適應飛利浦 Sonicare。
- 此款飛利浦 Sonicare 預設停用 Easy-start 功能。
啟動或關閉 Easy-start 功能:
- 若要啟用 Easy-start:
按住電源開關與模式按鈕 2 秒鐘。如果聽到 2 次嗶聲且電池電量
指示燈亮起綠燈,即表示 Easy-start 功能已經啟動。
- 若要關閉 Easy-start:
按住電源開關與模式按鈕 2 秒鐘。如果聽到 1 次嗶聲且電池電量
指示燈亮起黃燈,即表示 Easy-start 功能已經關閉。
1 / 1

Saeco HX8911/02 ユーザーマニュアル