Philips HQ6070/16 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル

このマニュアルも適しています

Register your product and get support at
www.philips.com/welcome
4222.002.5411.1
HQ6076,HQ6075,HQ6073,
HQ6071,HQ6070
1
2
3 4
5
6 7
8 9
10
11
12 13
14
15 16
17
18 19
20 21
22
23
24
03/07/2012
ENGLISH
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benet from the support that
Philips offers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Trimmer
2 Trimmer release button
3 Socket for small plug
4 Adapter
5 Small plug
6 Battery symbol
7 On/off button
8 Shaving unit release button
9 Shaving unit
10 Protection cap
11 Pouch (not shown)
Important
Read this user manual carefully before you use
the appliance and save it for future reference.
Danger
- Warning: Keep the adapter dry.
- This symbol means: Forbidden to rinse the
adapter under a running tap (Fig. 2).
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This symbol means: Forbidden to use in the
shower (Fig. 3).
- Warning: Do not use this appliance close to
a bathtub, shower or other containers lled
with water.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that
they do not play with the appliance.
Caution
- Do not use the shaver or the adapter if it
is damaged.
- Only use the adapter supplied.
- If the adapter is damaged, always have it
replaced with one of the original type in order
to avoid a hazard.
- Charge, use and store the shaver at a
temperature between 5°C and 35°C.
- Warning: Remove the detachable cord from
the handheld part before cleaning this part
in water.
- Be careful with hot water. Always check if
the water is not too hot, to avoid burning
your hands.
- Water may leak from the socket at the
bottom of the appliance when you rinse it.
This is normal and not dangerous because all
electronics are enclosed in a sealed power unit
inside the shaver.
- Do not immerse the shaver in water or
another liquid
- Do not use the shaver in combination with
pre-shave lotions, creams, foams, gels or other
cosmetic products.
General
- This shaver can be safely cleaned under the tap.
- This symbol means: Suitable to be cleaned
under a running tap (Fig. 4).
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
Compliance with standards
- This Philips appliance complies with all
standards regarding electromagnetic elds
(EMF). If handled properly and according to the
instructions in this user manual, the appliance
is safe to use based on scientic evidence
available today.
- This shaver complies with the applicable IEC
safety standards.
Charging
Make sure the appliance is switched off before you
start to charge it.
You can recharge the shaver between shaves, even
if the battery is not empty. This does not damage
the battery and prevents the battery from running
low during shaving.
Charging normally takes approx. 8 hours.
Do not leave the appliance connected to the
mains for more than 24 hours.
Charge indications
Charging
, When you start charging the shaver, the
battery symbol lights up (Fig. 5).
Battery running low
, HQ6076/HQ6075/HQ6073: When the
battery runs low, the red battery symbol
lights up. When you switch off the shaver, the
red battery symbol starts ashing. (Fig. 5)
, HQ6071/HQ6070: There is no indication that
the battery is low. The appliance switches off
automatically when the battery is completely
empty.
Charging the appliance
Charge the appliance when the red battery symbol
lights up or ashes (HQ6076/HQ6075/HQ6073)
or when the motor stops or starts running more
slowly (HQ6071/HQ6070).
1 Put the appliance plug in the shaver (Fig. 6).
2 Put the adapter in the wall socket.
3 When the battery is fully charged, remove
the adapter from the wall socket and pull the
appliance plug out of the shaver.
Cordless shaving time
A fully charged shaver has a cordless shaving time
of up to 40 minutes.
Using the appliance
Shaving
1 Press the on/off button once to switch on the
shaver.
The light ring lights up.
2 Move the shaving heads quickly over your
skin, making both straight and circular
movements (Fig. 7).
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
3 Press the on/off button once to switch on
the shaver.
4 To prevent damage to the shaving unit, put
the protection cap on the shaver after every
use (‘click’) (Fig. 8).
Trimming
For grooming sideburns and moustache.
1 Open the trimmer by pushing the slide
upwards (Fig. 9).
The trimmer can be activated while the motor
is running.
Cleaning and maintenance
Regular cleaning guarantees better shaving
performance.
The easiest and most hygienic way to clean the
appliance is to rinse the shaving unit and the hair
chamber with hot water every time you have used
the appliance.
For thorough cleaning of the shaving heads, we
advise you to use Philips Shaving Head Cleaning
Spray HQ110.
Every day: shaving unit and hair
chamber
Warning: Remove the detachable cord from the
handheld part before cleaning this part in water.
Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
1 Switch off the shaver, remove the adapter
from the wall socket and pull the appliance
plug out of the shaver.
2 Press the release button (1) and open the
shaving unit (2) (Fig. 10).
3 Clean the shaving unit and the hair chamber
by rinsing them under a hot tap for some
time (Fig. 11).
Make sure the inside of the shaving unit and the
hair chamber have been cleaned properly.
4 Rinse the outside of the appliance (Fig. 12).
5 Close the shaving unit and shake off excess
water.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
6 Open the shaving unit again and leave it open
to let the appliance dry completely (Fig. 13).
You can also clean the hair chamber without water
by using the brush supplied.
Every six months: shaving heads
1 Open the shaving unit.
You can also pull the shaving unit off the shaver for
easier cleaning.
2 To remove the shaving heads, do the
following.
- HQ6076/HQ6075: Remove the retaining
frame and take out the shaving heads. (Fig. 14)
- HQ6073/HQ6071/HQ6070: Open the shaving
unit, turn the wheel anticlockwise (1) and
remove the retaining frame (2). Then take out
the shaving heads (Fig. 15).
3 Clean the cutters and guards with the brush
supplied (your shaving heads may differ from
the one shown in the gure) (Fig. 16).
Problem Solution
The shaver
does not shave
as well as it
used to.
You may not have cleaned
the appliance properly. Clean
the shaving heads thoroughly
(see chapter ‘Cleaning and
maintenance’).
Long hairs may be obstructing
the shaving heads. Clean the
cutters and guards properly
with the brush supplied
(see chapter ‘Cleaning and
maintenance’).
The shaving heads may be
damaged or worn. Replace
the shaving heads (see chapter
‘Replacement’).
The shaver
does not
switch on
when I press
the on/off
button.
The battery may be empty.
Recharge the battery (see
chapter ‘Charging’).
The shaving
unit has come
off the shaver.
Simply reattach the shaving
unit by pressing it onto
the shaver (see chapter
‘Replacement’, step 5).
Environment
- Do not throw away the appliance with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve
the environment (Fig. 22).
- The built-in rechargeable shaver battery
contains substances that may pollute the
environment. Always remove the battery
before you discard and hand in the shaver at
an ofcial collection point. Dispose of the
battery at an ofcial collection point for
batteries. If you have trouble removing
the battery, you can also take the shaver
to a Philips service centre. The staff of this
centre will remove the battery for you and
will dispose of it in an environmentally safe
way (Fig. 23).
Disposal of the battery
Only remove the battery if it is completely empty.
1 Remove the adapter from the wall socket and
pull the appliance plug out of the shaver.
2 Let the shaver run until it stops, undo the
screws and open the shaver (Fig. 24).
3 Remove the battery.
Do not connect the shaver to the mains again
after the battery has been removed.
Guarantee and service
If you need information or if you have a
problem, please visit the Philips website at
www.philips.com/support or contact the
Philips Consumer Care Centre in your country.
You nd its phone number in the worldwide
guarantee leaet. If there is no Consumer Care
Centre in your country, go to your local Philips
dealer.
Guarantee restrictions
The shaving heads (cutters and guards) are
not covered by the terms of the international
guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/support
for a list of frequently asked questions or contact
the Consumer Care Centre in your country.
- HQ6076/HQ6075: Remove the retaining
frame and take out the shaving heads. (Fig. 14)
- HQ6073/HQ6071/HQ6070: Open the shaving
unit, turn the wheel anticlockwise (1) and
remove the retaining frame (2). Then take out
the shaving heads (Fig. 15).
4 Put the new shaving heads in the shaving unit
and reassemble the shaving unit (Fig. 17).
- HQ6076/HQ6075: Make sure that the
projections of the shaving heads t into the
recesses when you put them in the shaving
unit. Then place the retaining frame back into
the shaving unit.
- HQ6073/HQ6071/HQ6070: Put the shaving
heads in the shaving unit. Put the retaining
frame back into the shaving unit and turn the
lock clockwise (your shaving heads may differ
from the one shown in the gure).
Note: If you removed the shaving unit from the
shaver, reattach it. First insert the hinge of the shaving
unit into the slot in the rim of the hair chamber and
then push the shaving unit home until it locks into
place (‘click’). (Fig. 18)
5 Close the shaving unit.
Ordering accessories
To retain the top performance of your
shaver, make sure you clean it regularly and
replace its shaving heads at the recommended
time.To purchase accessories for your shaver,
please visit our online shop at
www.shop.philips.com/service. If the online
shop is not available in your country, go to your
Philips dealer or a Philips service centre. If you have
any difculties obtaining accessories for your shaver,
please contact the Philips Consumer Care Centre
in your country. You nd its contact details in the
worldwide guarantee leaet.
Shaving heads
- We advise you to replace your shaving heads
every two years. Always replace with the
appropriate shaving heads for your type of
shaver (Fig. 21).
Cleaning
- Use Cleaning Spray HQ110 to clean the
shaving heads thoroughly.
Accessories available for this shaver
HQ8 Precise Cutting System Shaving Heads.
HQ8505 powerplug.
HQ110 Philips Shaving Head Cleaning Spray.
Do not clean more than one cutter and guard
at a time, since they are all matching sets. If you
accidentally mix up the cutters and guards, it
may take several weeks before optimal shaving
performance is restored.
4 Put the shaving heads back into the shaving
unit and reassemble the shaving unit (Fig. 17).
- HQ6076/HQ6075: Make sure that the
projections of the shaving heads t into the
recesses when you put them back. Then place
the retaining frame back into the shaving unit.
- HQ6073/HQ6071/HQ6070: Put the shaving
heads back into the shaving unit. Put the
retaining frame back into the shaving unit and
turn the lock clockwise (your shaving heads
may differ from the one shown in the gure).
Note: If you removed the shaving unit from the
shaver, reattach it. First insert the hinge of the shaving
unit into the slot in the rim of the hair chamber and
then push the shaving unit home until it locks into
place (‘click’). (Fig. 18)
5 Close the shaving unit.
Trimmer
Clean the trimmer every time you have used it.
1 Switch off the shaver, remove the adapter
from the wall socket and pull the appliance
plug out of the shaver.
2 Clean the trimmer with the brush
supplied (Fig. 19).
3 Lubricate the trimmer teeth with a drop of
sewing machine oil every six months (Fig. 20).
Storage
- To prevent damage to the shaving unit, put the
protection cap on the shaver (‘click’) (Fig. 8).
- HQ6076/HQ6075/HQ6073: Store the
appliance in the pouch.
Replacement
To maintain optimal shaving results, replace the
shaving heads every two years.
Replace damaged or worn shaving heads with
HQ8 Precise Cutting System Shaving Heads.
1 Switch off the shaver, remove the adapter
from the wall socket and pull the appliance
plug out of the shaver.
2 Open the shaving unit.
You can also pull the shaving unit off the shaver.
3 To remove the shaving heads, do the
following.
6 再次打开剃须刀头部件,使它保持打开状
态,让产品完全晾干。(图13)
除了冲洗方式外,您还可以使用随附的刷子清
洁胡茬储藏室。
每 6 个月:剃须刀头
1 打开剃须刀头部件。
您也可以将剃须刀头部件从剃须刀拉出,以便
于清洁。
2 要拆卸剃须刀头,请执行以下操作。
- HQ6076/HQ6075:取下固定架并取出剃
须刀头。 (图 14)
- HQ6073/HQ6071/HQ6070:打开剃须刀
头部件,逆时针方向转动轮轴 (1) 并取下
固定架 (2)。然后取出剃须刀头。 (图 15)
3 用随附的刷子清洁刀片和网罩(剃须刀头
可能与图中显示的刀头不同)。(图16)
不要同时清洁多组刀片和网罩,因为它们都
是相互匹配的。如果不小心将刀片和网罩弄
混,则需要数周时间才能恢复产品的最佳剃
须性能。
4 将剃须刀头放回剃须刀头部件并重新组装
剃须刀头部件。(图17)
- HQ6076/HQ6075:放回时,确保剃须刀
头凸起部位正好插入凹陷部位。然后将固
定架重新装回剃须刀头部件中。
- HQ6073/HQ6071/HQ6070:将剃须刀头
重新安装到剃须刀头部件上。将固定架装
回剃须刀头部件,顺时针转动并锁住(剃
须刀头可能与图中显示的刀头不同)。
注意:如果您已从剃须刀卸下剃须刀头部
件,请重新安装。首先将剃须刀头部件的铰链
插入胡茬储藏室边缘的插槽,然后将剃须刀头
部件推到原位,直至其锁定到位(可听到“咔
哒”一声)。(图18)
5 关闭剃须刀头部件。
修发器
每次使用后都要清洁修剪器。
1 关闭剃须刀电源,从电源插座上拔下适配
器,并从剃须刀上拔下产品插头。
2 用随附的刷子清洁修发器。(图19)
3 每六个月用一滴缝纫机油润滑修发器齿。
(图20)
存储
- 为防止损坏剃须刀头部件,请将保护盖盖
在剃须刀上(可听到“咔哒”一声)。
(图 8)
- HQ6076/HQ6075/HQ6073:将产品存放
在软袋中。
使用本产品
剃毛
1 按一下开/关按钮打开剃须刀。
光环亮起。
2 将剃须刀头在皮肤上快速移动,作直线和
迂回动作。(图7)
在干爽的面部剃须效果最佳。
您的皮肤可能需要 2 到 3 周才能适应飞利浦
剃须系统。
3 按一下开/关按钮打开剃须刀。
4 为防止损坏剃须刀头部件,每次使用后,
请将保护盖盖在剃须刀上(可听到“咔
哒”一声)。(图8)
修发
用于修剪鬓角和小胡子。
1 向上推动滑块来打开修发器。(图9)
当马达运转时,修发器便可以启动。
清洁和保养
为保证更好的剃须效果,剃须刀必须定期清
洗。
最简单和最卫生的清洁方法是每次使用完本
产品之后,用热水冲洗剃须刀头部件和胡茬
储藏室。
为彻底清洁您的剃须刀头,我们建议您使用飞
利浦剃须刀头清洁喷雾剂 HQ110。
每天:剃须刀头部件和胡茬储藏室
警告:将手持部分与电源软线分开后,才能在
水中清洗手持部分。
使用热水时一定要小心。切记先检查水温是否
太高,以防烫手。
1 关闭剃须刀电源,从电源插座上拔下适配
器,并从剃须刀上拔下产品插头。
2 按下释放钮(1),打开剃须刀头部件(2)
。(图10)
3 在热水龙头下,冲洗剃须刀头部件和胡茬
储藏室一段时间。(图11)
确保剃须刀头部件和胡茬储藏室的内部已彻
底清洁。
4 冲洗产品表面。(图12)
5 关闭剃须刀头部件并甩掉多余的水份。
不要用毛巾或纸巾擦拭剃须刀头部件,因为这
样可能会损坏剃须刀头。
有的电子线路都密封在剃须刀内的一个密
封壳内。
- 不要将剃须刀浸入水中或其他液体中
- 请勿将本剃须刀与剃须润滑液、面霜、泡
沫、凝胶或其它护肤产品结合使用。
概述
- 这款剃须刀可放心在水龙头下清洗。
- 此符号表示:适合用在打开的水龙头下进
行清洗。 (图 4)
- 电源适配器可将 100-240 伏的电压转换为
24 伏以下的安全低电压。
符合标准
- 这款飞利浦产品符合关于电磁场 (EMF) 的
相关标准。据目前的科学证明,如果正
确使用并按照本用户手册中的说明进行操
作,本产品是安全的。
- 这款剃须刀符合 IEC 家电安全标准。
充电
开始充电之前确保产品电源已关闭。
您可以在两次剃须之间为剃须刀充电,即使电
池电量尚未耗尽。这不会损坏电池,并且可防
止电池在剃须过程中电量不足。
一般充电时间大约为 8 小时。
不要将本产品与电源接通超过24小时。
充电指示
充电
, 开始为剃须刀充电时,电池符号将亮起。
(图5)
电池电量不足
, HQ6076/HQ6075/HQ6073:当电池电量
不足时,红色电池符号将亮起。当关闭剃
须刀时,红色电池符号开始闪烁。(图5)
, HQ6071/HQ6070:当电池处于低电量状
态时没有提示。电池电量完全耗尽时产品
将自动关闭。
为产品充电
当红色电池符号亮起或闪烁时 (HQ6076/
HQ6075/HQ6073),或者当马达停止运转或
开始运转缓慢时 (HQ6071/HQ6070),应为产
品充电。
1 将产品插头插入剃须刀。(图6)
2 将电源适配器插入电源插座。
3 当电池充满电时,从电源插座上拔下适配
器,并从剃须刀上拔下产品插头。
不接电源的剃须时间
完全充电的剃须刀在不连接电源的情况下最长
可使用达 40 分钟。
简体中文
简介
感谢您的惠顾,欢迎光临飞利浦!为了您能充
分享受飞利浦提供的支持,请在 www.philips.
com/welcome 上注册您的产品。
基本说明 (图 1)
1 修发器
2 修发器释放钮
3 小插头的转换插座
4 适配器
5 小插头
6 电池符号
7 开/关按钮
8 剃须刀头部件释放按钮
9 剃毛刀头部件
10 保护盖
11 软袋(未显示)
注意事项
使用本产品之前,请仔细阅读本使用说明书,
并妥善保管以备日后参考。
危险
- 警告:保持适配器干燥。
- 此符号表示:禁止在水龙头下冲洗适配
器。 (图 2)
警告
- 电源适配器内含有一个变压器。切勿自行
更换插头,否则将导致严重后果。
- 此符号表示:禁止在洗澡或淋浴时使用。
(图 3)
- 警告:不要在盛水的浴缸、淋浴、洗脸盆
或其他器皿附近使用本器具。
- 本产品不打算由肢体不健全、感觉或精神
上有障碍或缺乏相关经验和知识的人(包
括儿童)使用,除非有负责他们安全的人
对他们使用本产品进行监督或指导。
- 应照看好儿童,确保他们不玩耍本产品。
注意
- 如果剃须刀或适配器已损坏,请勿再使
用。
- 只能使用随附的适配器。
- 如果适配器已损坏,则务必更换原装型号
适配器,以免发生危险。
- 必须在 5 摄氏度至 35 摄氏度之间的温度
下充电、使用和存放剃须刀。
- 警告:将手持部分与电源软线分开后,才
能在水中清洗手持部分。
- 使用热水时一定要小心。切记先检查水温
是否太高,以防手被烫伤。
- 冲洗产品时,水可能从产品底部的插口漏
出。这是正常的,而且没有危险,因为所
问题 解决方法
过长的胡须可能堵塞了剃须刀
头。请使用随附的刷子正确清
洁刀片和网罩(见“清洁和保
养”一章)。
剃须刀头可能已损坏或磨损。
请更换剃须刀头(见“更换”
一章)。
按下开/关
按钮时,
剃须刀不
能启动。
电池可能没电。为电池充电
(见“充电”一章)。
剃须刀头
部件从剃
须刀上脱
落了。
只需重新安装剃须刀头部件,
将其按到剃须刀上(见“更
换”一章,步骤 5)。
HQ8505 电源插头。
HQ110 飞利浦剃须刀头清洁喷雾剂。
环保
- 弃置产品时,请不要将其与一般生活垃圾
堆放在一起;应将其交给官方指定的回收
点。这样做有利于环保。 (图 22)
- 内置充电电池含有可能会污染环境的物
质。丢弃剃须刀时,一定要将电池取出,
并将剃须刀送到官方指定的回收站。到官
方指定的电池回收站处理电池。如果您在
取出电池时遇到问题,您也可以将剃须刀
送至飞利浦维修中心。维修中心的员工会
帮您取出电池,并以环保的方式处理它。
(图 23)
处理电池
仅在电池电量完全耗尽后方可取出电池。
1 从电源插座上拔下适配器,并从剃须刀上
拔下产品插头。
2 让剃须刀运转直到停止,拧下螺钉并打开
剃须刀。(图24)
3 取出电池。
取出电池后,不要再将剃须刀与电源连接在
一起。
保修与服务
如果您需要了解信息或有任何疑问,请访问飞
利浦网站:www.philips.com/support。您也可
以联系您所在国家/地区的飞利浦客户服务中
心(可在全球保修卡中找到其电话号码)。如
果您所在的国家/地区没有客户服务中心,请
向当地的飞利浦经销商求助。
保修条款
由于剃须刀头(刀片和网罩)属于易磨损物
品,因此不在国际保修条款的涵盖范围之列。
故障种类和处理方法
本章归纳了使用本产品时最常见的一些问
题。如果您无法根据以下信息解决问题,请
访问 www.philips.com/support 查阅常见问
题列表,或联系您所在国家/地区的客户服务
中心。
问题 解决方法
剃须刀的
剃须效果
没有以前
好。
您可能没有正确清洁本产品。
请彻底清洁剃须刀头(见“清
洁和保养”一章)。
更换
为保持最佳剃须效果,请每两年更换一次剃
须刀头。
损坏或磨损的剃须刀头只能用 HQ8 精确切剃
系统剃须刀头更换。
1 关闭剃须刀电源,从电源插座上拔下适配
器,并从剃须刀上拔下产品插头。
2 打开剃须刀头部件。
您也可以将剃须刀头部件从剃须刀拉出。
3 要拆卸剃须刀头,请执行以下操作。
- HQ6076/HQ6075:取下固定架并取出剃
须刀头。 (图 14)
- HQ6073/HQ6071/HQ6070:打开剃须刀
头部件,逆时针方向转动轮轴 (1) 并取下
固定架 (2)。然后取出剃须刀头。 (图 15)
4 将新剃须刀头放入剃须刀头部件并重新组
装剃须刀头部件。(图17)
- HQ6076/HQ6075:放入剃须刀头部件
时,确保剃须刀头的凸起部位正好插入凹
陷部位。将固定架重新装回剃须刀头部
件。
- HQ6073/HQ6071/HQ6070:将剃须刀头
放入剃须刀头部件。将固定架装回剃须刀
头部件,然后顺时针转动锁(剃须刀头可
能与图中显示的刀头不同)。
注意:如果您已从剃须刀卸下剃须刀头部
件,请重新安装。首先将剃须刀头部件的铰链
插入胡茬储藏室边缘的插槽,然后将剃须刀头
部件推到原位,直至其锁定到位(可听到“咔
哒”一声)。(图18)
5 关闭剃须刀头部件。
订购附件
为了保持剃须刀的最佳性能,请确保定期清洁
并在推荐的时间更换剃须刀头。
要为您的剃须刀购买附件,请访问我们的网上
商城:www.shop.philips.com/service。如果
您所在国家/地区没有网上商城,请联系您的
飞利浦经销商或飞利浦服务中心。如果您购买
剃须刀的附件有困难,请联系您所在国家/地
区的飞利浦客户服务中心。可在全球保修卡中
找到其详细联系信息。
剃须刀头
- 建议您每两年更换一次剃须刀头。务必使
用适合剃须刀类型的剃须刀头进行更换。
(图 21)
清洁
- 使用清洁喷雾剂 HQ110 彻底清洁剃须刀
头。
此剃须刀的可用附件
HQ8 精确切剃系统的剃须刀头。
1 / 1

Philips HQ6070/16 ユーザーマニュアル

カテゴリー
メンズシェーバー
タイプ
ユーザーマニュアル
このマニュアルも適しています

他の言語で