TP-LINK tp-link Tapo C120 Home Security WiFi Camera ユーザーガイド

1. Position your camera’s adjustable stand for

setup.

Set Up Your Camera

Note: Peel o lm from the camera before use.

Install Your Camera

1. Stick the mounting template to the desired

mounting place. Drill two holes according

to the template.

1. Drill one hole in the desired mounting

place.

2. Insert two anchors into the holes and use the

screws to ax the mental plate over the

anchors. Then attach the camera to the plate.

2. Insert one anchor into the hole and use one

screw to ax the camera over the anchor.

Option 1: Set on a table or shelf Option 2: Mount to metallic surfaces Option 3: Stick to a clean wall Option 4. Mount to the wall (with or without the mental plate)

1. Attach the included adhesive to the back of

the mental plate.

The camera includes a magnet in its base. It

allows magnetically attaching to metallic

surfaces.

2. Stick the mental plate with adhesive to a clean

wall. Then attach the camera to the plate.

1. Place the camera on your desired table or

shelf.

2. Adjust the stand angle to the notch position

in the base for more stability.

Note: This is applicable with tile, glass, marble, metal,

stainless steel, and hard wall surfaces.

2. Download the Tapo app from the App

Store or Google Play.

3. Power up the camera. Tap the button in

the app and select your model. Follow app

instructions to complete setup.

6 mm (15/64 in.)

This equipment shall be installed at a height of fewer than 2 meters. This equipment shall be installed at a height of fewer than 2 meters.This equipment shall be installed at a height of fewer than 2 meters.

Metallic Surface

6 mm (15/64 in.)

3M Adhesive

Appearance System LED Indications

For technical support, user guides,

FAQs, warranty and more, please

visit www.tapo.com/support/

TP-Link hereby declares that the device is in compliance with the

essential requirements and other relevant provisions of directives

2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The

original EU declaration of conformity may be found at

https://www.tapo.com/support/ce

TP-Link hereby declares that the device is in compliance with the

essential requirements and other relevant provisions of the Radio

Equipment Regulations 2017. The original UK declaration of

conformity may be found at https://www.tapo.com/support/ukca/ *Images may dier from your actual product.

Indoor/Outdoor

Home Security Wi-Fi Camera

Tapo C120

Quick Start Guide

BackFront

5Speaker

6USB Type-C Charging Port

2White Light LEDs

System LED

4Microphone

3Lens

Blinking red and green

Blinking red slowly

Solid amber

Blinking red quickly

Solid red

Solid green

Blinking green quickly

Starting up

Connected to the cloud

Ready for setup

Connecting to Wi-Fi

Connected to Wi-Fi

Camera resetting

Camera updating

Side

microSD Card Slot

Open the cover. Insert a microSD card (not included) and initialize

it on the Tapo app for local recording.

Reset

Open the cover. Use a pin to press and hold for at least 5 seconds

to reset the camera to factory default settings.

microSD

• Do not use damaged charger or USB cable to charge the device.

• Do not use any other chargers than those recommended.

• Do not use the device where wireless devices are not allowed.

• Adapter shall be easily accessible.

• Use only power supplies which are provided by manufacturer and in

the original packing of this product. If you have any questions, please

don't hesitate to contact us.

• Keep the device away from re or hot environments. DO NOT

immerse in water or any other liquid.

• Do not disassemble, repair or modify the product.

• Do not use the product if the casing has been broken. Danger of

electric shock.

• Never touch the product with wet hands.

• Do not place near automatically controlled devices such as re

alarms. Radio waves emitted from this product may cause such

devices to malfunction resulting in an accident.

• Observe restrictions on using wireless products in fuel depots,

chemical plants or when blasting operations are in progress.

• Do not use liquid to clean the product. Only use a dry cloth.

• Never put metal objects inside the product. If a metal object enters

the product turn o the circuit breaker and contact an authorised

electrician.

• This product is not intended to be used when providing medical care.

Consult the manufacturer of any personal medical devices, such as

pacemakers or hearing aids to determine if they are adequality

shielded from external RF (radio frequency) energy.

• Do not use this product in health care facilities. Hospitals or health

care facilities may be using equipment that could be sensitive to

external RF energy.

• Do not place heavy objects on top of the product.

• When you leave the product unused for a long time unplug the

product from the power outlet.

• This product may interfere with other electronic products such as

TV, radios, personal computers, phones or other wireless devices.

• Adapter should be used indoors where the ambient temperature is

lower than or equal to 40 ºC.

• Operating Temperature: -25 ºC ~ 45 ºC (-13 °F ~ 113 °F )

Please read and follow the above safety information when operating

the device. We cannot guarantee that no accidents or damage will

occur due to improper use of the device. Please use this product with

care and operate at your own risk.

Adjust View

Tilt and rotate the camera and stand for your desired viewing angle.

FCC compliance information statement

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

•Consult the dealer or an experienced radio/ TV technician for

help.

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions:

1）This device may not cause harmful interference.

2）This device must accept any interference received, including

interference that may cause undesired operation.

Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority

to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV

interference caused by unauthorized modifications to this

equipment. Such modifications could void the user’s authority to

operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits

set forth for an uncontrolled environment.

This device and its antenna must not be co-located or operating

in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements,

this grant is applicable to only Mobile Configurations. The

antennas used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must

not be co-located or operating in conjunction with any other

antenna or transmitter.”

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s)

that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is

subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including

interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent

appareil est conforme aux CNR d’Innovation, Sciences et

Développement économique Canada applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le

fonctionnement.

Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 20cm between

the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux

rayonnements IC établies pour un environnement non contrôlé.

Cet équipement doit être installé et utilisé avec un minimum de

20 cm de distance entre la source de rayonnement et votre

corps.

Industry Canada Statemen

CAN ICES-3 (B)/NMB-3(B)

BSMI Notice

安全諮詢及注意事項

請使用原裝電源供應器或只能按照本產品注明的電源類型使用本

產品。

清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或

濕布進行清潔。

注意防潮，請勿將水或其他液體潑灑到本產品上。

插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，

請勿堵塞或覆蓋開口。

請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則

不可放在密閉位置中。

不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商

聯繫。

NCC Notice

注意！

取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用

者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

低功率射頻器材之使用不得影響飛航安全及干擾合法通信；

經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續

使用。

前述合法通信，指依電信管理法規定作業之無線電通信。

低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射

性電機設備之干擾。

為避免本器材影像畫面遭偷窺或擷取，本器材使用者應先修改預

設密碼，並定期更新密碼。