MSI 7C96 取扱説明書

1

󷸺󳜼 Contents

Contents

2

3

 6

LAN Port LED Status Table ........................................................................................6

7

CPU Socket .................................................................................................................8

DIMM Slots..................................................................................................................9

PCI_E1~2: PCIe Expansion Slots ................................................................................9

M2_1: M.2 Slot ..........................................................................................................10

SATA1~4: SATA 6Gb/s Connectors ...........................................................................10

JFP1, JFP2: Front Panel Connectors .......................................................................11

JAUD1: Front Audio Connector ................................................................................11

ATX_PWR1, CPU_PWR1: Power Connectors ...........................................................12

JUSB1, JUSB2: USB 2.0 Connectors ........................................................................13

JUSB3: USB 3.2 Gen1 Connector .............................................................................13

CPU_FAN1, SYS_FAN1: Fan Connectors .................................................................14

JTPM1: TPM Module Connector ...............................................................................14

JCI1: Chassis Intrusion Connector ...........................................................................15

JCOM1: Serial Port Connector .................................................................................15

JBAT1: Clear CMOS (Reset BIOS) Jumper ...............................................................16

EZ Debug LED ...........................................................................................................16

17

BIOS Setup ................................................................................................................18

Entering BIOS Setup .................................................................................................18

Resetting BIOS ..........................................................................................................18

Updating BIOS...........................................................................................................19

20

Installing Windows® 10 .............................................................................................20

Installing Drivers ......................................................................................................20

Installing Utilities .....................................................................................................20

Thank you for purchasing the MSI® 

motherboard. This User Guide gives information about

board layout, component overview, BIOS setup and software

installation.

2



 The components included in this package are prone to damage from electrostatic

discharge (ESD). Please adhere to the following instructions to ensure successful

computer assembly.

 Ensure that all components are securely connected. Loose connections may cause

the computer to not recognize a component or fail to start.

 Hold the motherboard by the edges to avoid touching sensitive components.

 It is recommended to wear an electrostatic discharge (ESD) wrist strap when

handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is

not available, discharge yourself of static electricity by touching another metal object

before handling the motherboard.

 Store the motherboard in an electrostatic shielding container or on an anti-static

pad whenever the motherboard is not installed.

 Before turning on the computer, ensure that there are no loose screws or metal

components on the motherboard or anywhere within the computer case.

 Do not boot the computer before installation is completed. This could cause

permanent damage to the components as well as injury to the user.

 If you need help during any installation step, please consult a certified computer

technician.

 Always turn off the power supply and unplug the power cord from the power outlet

before installing or removing any computer component.

 Keep this user guide for future reference.

 Keep this motherboard away from humidity.

 Make sure that your electrical outlet provides the same voltage as is indicated on

the PSU, before connecting the PSU to the electrical outlet.

 Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.

 All cautions and warnings on the motherboard should be noted.

 If any of the following situations arises, get the motherboard checked by service

personnel:

 Liquid has penetrated into the computer.

 The motherboard has been exposed to moisture.

 The motherboard does not work well or you can not get it work according to

user guide.

 The motherboard has been dropped and damaged.

 The motherboard has obvious sign of breakage.

 Do not leave this motherboard in an environment above 60°C (140°F), it may

damage the motherboard.

3

 





Support 3rd Gen AMD Ryzen™ Desktop Processors and AMD

Ryzen™4000 G-Series Desktop Processors



 AMD B550 Chipset (B550M-A PRO)

 AMD A520 Chipset (A520M-A PRO)



 2x DDR4 memory slots, support up to 64GB*

 Supports DDR4 1866/ 2133/ 2400/ 2667/ 2800/ 2933/

3000/ 3066/ 3200 MHz by JEDEC

 Supports DDR4 2667/ 2800 /2933 /3000 /3066 /3200

/3466 /3600/ 3733 /3866 /4000 /4133 /4266 /4400/ 4600+

MHz by A-XMP OC MODE

 1DPC 1R max speed 4600 MHz

 1DPC 2R max speed 3866 MHz

 Dual channel memory architecture

 Supports non-ECC UDIMM memory

 Supports ECC UDIMM memory (non-ECC mode)

 Supports un-buffered memory

* Please refer www.msi.com for more information on

compatible memory.



 1x PCIe 3.0 x1 slot

 1x PCIe x16 slot

 B550M-A PRO supports PCIe 4.0/3.0*

 A520M-A PRO supports PCIe 3.0

* PCIe specifications may vary depending on the CPU

installed.





 1x HDMI 2.1 port, supporting a maximum resolution of

4096x2160 @60Hz*

/

**

 1x DVI-D port, supporting a maximum resolution of

1920x1200 @60Hz*

 Maximum shared memory of 16GB

* Available for the processor with integrated graphics.

** Graphics specifications may vary depending on the CPU

installed.



Realtek® ALC892 Codec

 7.1-Channel High Definition Audio

Continued on next page

4



Continued from previous page

  1x Realtek® RTL8111H 1Gbps LAN controller



AMD B550/A520 Chipset

 4x SATA 6Gb/s ports

 1x M.2 slot (Key M) (from AMD Processor)

 B550M-A PRO supports PCIe 4.0/3.0*

 A520M-A PRO supports PCIe 3.0

 Supports SATA 6Gb/s

 Supports 2242/ 2260/ 2280 storage devices

* PCIe specifications may vary depending on the CPU

installed.



AMD B550/A520 Chipset

 2x USB 3.2 Gen 1 5Gbps ports are available through the

internal USB 3.2 Gen 1 5Gbps connector

 6x USB 2.0 ports (2 Type-A ports on the back panel, 4

ports through the internal USB 2.0 connectors)

AMD Processor

 4x USB 3.2 Gen 1 5Gbps Type-A ports on the back panel





 1x 24-pin ATX main power connector

 1x 4-pin ATX 12V power connector

 4x SATA 6Gb/s connectors

 1x M.2 slots (M-Key)

 1x USB 3.2 Gen 1 5Gbps connector (supports additional 2

USB 3.2 Gen 1 5Gbps ports)

 2x USB 2.0 connectors (supports additional 4 USB 2.0 ports)

 1x 4-pin CPU fan connector

 1x 4-pin system fan connector

 1x Front panel audio connector

 2x System panel connectors

 1x Chassis Intrusion connector

 1x TPM module connector

 1x Clear CMOS jumper

Continued on next page



 

Continued from previous page





 1x HDMI port

 1x DVI-D port

 1x PS/2 mouse port

 1x PS/2 keyboard port

 4x USB 3.2 Gen 1 5Gbps Type-A ports

 2x USB 2.0 Type-A ports

 1x LAN (RJ45) port

 3x audio jacks

 NUVOTON NCT6687-R Controller Chip





 CPU/ System/ Chipset temperature detection

 CPU/ System fan speed detection

 CPU/ System fan speed control



 mATX Form Factor

 9.3 in. x 7.9 in. (23.6 cm x 20 cm)



 1x 256 Mb flash

 UEFI AMI BIOS

 ACPI 6.0, SMBIOS 2.8

 Multi-language



 Drivers

 DRAGON CENTER

 CPU-Z MSI GAMING

 Google Chrome™, Google Toolbar, Google Drive

 Norton™ Internet Security Solution





 User Scenario

 Hardware Monitor

 True Color

 Live Update

 Speed Up

 Smart Tool

 Super Charger

Please refer to http://

download.msi.com/manual/

mb/DRAGONCENTER2.pdf for

more details.

6





 

Off No link

Yellow Linked

Blinking Data activity



 

Off 10 Mbps connection

Green 100 Mbps connection

Orange 1 Gbps connection





To configure 7.1-channel audio, you have to connect front audio I/O module to JAUD1

connector and follow the below steps.

 Click on the  to open the dialog

below.

 Select .

 Plug your speakers to audio jacks on rear and front I/O panel. When you plug into

a device at an audio jack, a dialogue window will pop up asking you which device

is current connected.

USB 3.2 Gen 1

(5Gbps) Type-A

PS/2 Keyboard

PS/2 Mouse

LAN

Line-in

Mic in

Line-out

DVI-D

USB 2.0 Type-A

7

 



* Distance from the center of the CPU to the nearest DIMM slot.

M2_1

JTPM1

JUSB2

JUSB1

CPU_FAN1

SYS_FAN1

PCI_E1

PCI_E2

Processor Socket

CPU_PWR1

JCI1

JCOM1

JAUD1

JFP1

JFP2

ATX_PWR1

SATA4

SATA3

SATA2

SATA1

JUSB3

JBAT1

DIMMB1

DIMMA1

50.89mm*

8





Please install the CPU into the CPU socket as shown below.

1

3



4

6

7

8

2







Always unplug the power cord from the power outlet before installing or removing

the CPU.



Please retain the CPU protective cap after installing the processor. MSI will deal

with Return Merchandise Authorization (RMA) requests if only the motherboard

comes with the protective cap on the CPU socket.



When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink

is necessary to prevent overheating and maintain system stability.





your system.



Overheating can seriously damage the CPU and motherboard. Always make sure

the cooling fans work properly to protect the CPU from overheating. Be sure to apply

an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to

enhance heat dissipation.



If you purchased a separate CPU and heatsink/ cooler, Please refer to the docu-

mentation in the heatsink/ cooler package for more details about installation.

9

 



Please install the memory module into the DIMM slot as shown below.

1

2

3

2







Due to chipset resource usage, the available capacity of memory will be a little less

than the amount of installed.



Please note that the maximum capacity of addressable memory is 4GB or less

for 32-bit Windows OS due to the memory address limitation. Therefore, we recom

-

mended that you to install 64-bit Windows OS if you want to install more than 4GB

memory on the motherboard.









If you install a large and heavy graphics card, you need to use a tool such as 

 to support its weight to prevent deformation

of the slot.



󼶫

unplug the power supply power cable from the power outlet. Read the expansion

card’s documentation to check for any necessary additional hardware or software

changes.

PCIe 4.0/ 3.0 x16 (CPU)

 PCIe 3.0 x1 (PCH)

10





These connectors are SATA 6Gb/s interface ports. Each connector can connect to one

SATA device.

SATA3

SATA4

SATA1

SATA2







Please do not fold the SATA cable at a 90-degree angle. Data loss may result

during transmission otherwise.



SATA cables have identical plugs on either sides of the cable. However, it is



saving purposes.



Please install the M.2 device into the M.2 slot as shown below.

1

3

Standoff

Supplied

M.2 screw

30º30º

2

11

 



These connectors connect to the switches and LEDs on the front panel.

1

2 10

9

+

+-

--

-

+

Power LED

HDD LED Reset Switch

Reserved

Power Switch

1 HDD LED + 2 Power LED +

3 HDD LED - 4 Power LED -

5 Reset Switch 6 Power Switch

7 Reset Switch 8 Power Switch

9 Reserved 10 No Pin

JFP2

1

+

-

Speaker

Buzzer

1 Speaker - 2 Buzzer +

3 Buzzer - 4 Speaker +

HDD LED

RESET SW

HDD LED

HDD LED -

HDD LED +

POWER LED -

POWER LED +

POWER LED

JFP1



This connector allow you to connect audio jacks on the front panel.

1

2 10

9

1 MIC L 2 Ground

3 MIC R 4 NC

5 Head Phone R 6 MIC Detection

7 SENSE_SEND 8 No Pin

9 Head Phone L 10 Head Phone Detection

12





These connectors allow you to connect an ATX power supply.





Make sure that all the power cables are securely connected to a proper ATX power

supply to ensure stable operation of the motherboard.

24

131

12

ATX_PWR1

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V

3 Ground 15 Ground

4 +5V 16 PS-ON#

5 Ground 17 Ground

6 +5V 18 Ground

7 Ground 19 Ground

8 PWR OK 20 Res

9 5VSB 21 +5V

10 +12V 22 +5V

11 +12V 23 +5V

12 +3.3V 24 Ground

3

2 1

4

CPU_PWR1

1 Ground 3 +12V

2 Ground 4 +12V

13

 



These connectors allow you to connect USB 3.2 Gen1 ports on the front panel.

1

10

11

20

1 Power 11 USB2.0+

2 USB3_RX_DN 12 USB2.0-

3 USB3_RX_DP 13 Ground

4 Ground 14 USB3_TX_C_DP

5 USB3_TX_C_DN 15 USB3_TX_C_DN

6 USB3_TX_C_DP 16 Ground

7 Ground 17 USB3_RX_DP

8 USB2.0- 18 USB3_RX_DN

9 USB2.0+ 19 Power

10 NC 20 No Pin





Note that the Power and Ground pins must be connected correctly to avoid possible

damage.



These connectors allow you to connect USB 2.0 ports on the front panel.

1

2 10

9

1 VCC 2 VCC

3 USB0- 4 USB1-

5 USB0+ 6 USB1+

7 Ground 8 Ground

9 No Pin 10 NC







Note that the VCC and Ground pins must be connected correctly to avoid possible

damage.



In order to recharge your iPad,iPhone and iPod through USB ports, please install

MSI® SUPER CHARGER software.

14







You can adjust fan speed in 



PWM Mode fan connectors provide constant 12V output and adjust fan speed with

speed control signal. When you plug a 3-pin (Non-PWM) fan to a fan connector in

PWM mode, the fan speed will always maintain at 100%, which might create a lot of

noise.

1



1 Ground 2 +12V

3 Sense 4 Speed Control Signal













CPU_FAN1 PWM mode 1A 12W

SYS_FAN1 PWM mode 1A 12W

1



1 Ground 2 Voltage Control

3 Sense 4 NC

1

2

12

11

1 SPI Power 2 SPI Chip Select

3

Master In Slave Out (SPI

Data)

4

Master In Slave In (SPI

Data)

5 Reserved 6 SPI Clock

7 Ground 8 SPI Reset

9 Reserved 10 No Pin

11 Reserved 12 Interrupt Request



This connector is for TPM (Trusted Platform Module). Please refer to the TPM

security platform manual for more details and usages.



 



This connector allows you to connect the chassis intrusion switch cable.

Normal

(default)

Trigger the chassis

intrusion event



 Connect the  connector to the chassis intrusion switch/ sensor on the

chassis.

 Close the chassis cover.

 Go to .

 Set  to .

 Press F10 to save and exit and then press the  key to select .

 Once the chassis cover is opened again, a warning message will be displayed on

screen when the computer is turned on.



 Go to .

 Set  to Reset.

 Press to save and exit and then press the  key to select .



This connector allows you to connect the optional serial port with bracket.

1

2 10

9

1 DCD 2 SIN

3 SOUT 4 DTR

5 Ground 6 DSR

7 RTS 8 CTS

9 RI 10 No Pin

16





There is CMOS memory onboard that is external powered from a battery located on

the motherboard to save system configuration data. If you want to clear the system

configuration, set the jumpers to clear the CMOS memory.

Keep Data

(default)

Clear CMOS/ Reset

BIOS



 Power off the computer and unplug the power cord.

 Use a jumper cap to short JBAT1 for about 5-10 seconds.

 Remove the jumper cap from JBAT1.

 Plug the power cord and power on the computer.



These LEDs indicate the status of the motherboard.

 - indicates CPU is not detected or fail.

 - indicates DRAM is not detected or fail.

 - indicates GPU is not detected or fail.

 - indicates booting device is not detected or fail.

17

 



MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface)

architecture. UEFI has many new functions and advantages that traditional BIOS

cannot achieve, and it will completely replace BIOS in the future. The MSI UEFI

BIOS uses UEFI as the default boot mode to take full advantage of the new chipset’s

capabilities. However, it still has a CSM (Compatibility Support Module) mode to be

compatible with older devices. That allows you to replace legacy devices with UEFI

compatible devices during the transition.





The term BIOS in this user guide refers to UEFI BIOS unless otherwise noted.



 Fast booting - UEFI can directly boot the operating system and save the BIOS self-

test process. And also eliminates the time to switch to CSM mode during POST.

 Supports for hard drive partitions larger than 2 TB.

 Supports more than 4 primary partitions with a GUID Partition Table (GPT).

 Supports unlimited number of partitions.

 Supports full capabilities of new devices - new devices may not provide backward

compatibility.

 Supports secure startup - UEFI can check the validity of the operating system to

ensure that no malware tampers with the startup process.



 - this motherboard supports only 64-bit

Windows 10 operating system.

  - the system will detect your graphics card. When display a

warning message 







We recommend that you to use a GOP/ UEFI compatible graphics card.



After entering the BIOS, find the BIOS Mode at the top of the screen.

 





















18





The default settings offer the optimal performance for system stability in normal

conditions. You should  to avoid possible system

damage or failure booting unless you are familiar with BIOS.







BIOS items are continuous update for better system performance. Therefore, the

󼶫

reference only. You could also refer to the  information panel for BIOS item

description.



The BIOS items will vary with the processor.



Press  key, when the

 message appears on the screen during the boot process.



F1: General Help

F2: Add/ Remove a favorite item

F3: Enter Favorites menu

F4: Enter CPU Specifications menu

: Enter Memory-Z menu

F6: Load optimized defaults

F7: Switch between Advanced mode and EZ mode

F8: Load Overclocking Profile

F9: Save Overclocking Profile

F10: Save Change and Reset*

F12: Take a screenshot and save it to USB flash drive (FAT/ FAT32 format only).

: Enter Search page

* When you press F10, a confirmation window appears and it provides the

modification information. Select between Yes or No to confirm your choice.



You might need to restore the default BIOS setting to solve certain problems. There

are several ways to reset BIOS:

 Go to BIOS and press F6 to load optimized defaults.

 Short the  jumper on the motherboard.





Please refer to the jumper section for resetting BIOS.

19

 





Before updating:

Please download the latest BIOS file that matches your motherboard model from MSI

website. And then save the BIOS file into the USB flash drive.

Updating BIOS:

 Insert the USB flash drive that contains the update file into the USB port.

 Please refer the following methods to enter flash mode.

 Reboot and press  key during POST and click on  to reboot the

system.

 Reboot and press  key during POST to enter BIOS. Click the 

button and click on  to reboot the system.

 Select a BIOS file to perform the BIOS update process.

 When prompted click on  to start recovering BIOS.

 After the flashing process is 100% completed, the system will reboot

automatically.



Before updating:

Make sure the LAN driver is already installed and the internet connection is set

properly.

Updating BIOS:

 Install and launch MSI DRAGON CENTER and go to  page.

 Select  and click on Advance button.

 Click on Scan button to search the latest BIOS file.

 Select the BIOS file and click on  icon to download and install the latest

BIOS file.

 Click  and choose . And then click  and  to start

updating BIOS.

 After the flashing process is 100% completed, the system will restart

automatically.

20



Please download and update the latest utilities and drivers at www.msi.com



 Power on the computer.

 Insert the Windows® 10 installation disc/USB into your computer.

 Press the  button on the computer case.

 Press F11 key during the computer POST (Power-On Self Test) to get into Boot

Menu.

 Select the Windows® 10 installation disc/USB from the Boot Menu.

 Press any key when screen shows 

message.

 Follow the instructions on the screen to install Windows® 10.



 Start up your computer in Windows® 10.

 Insert MSI® Driver Disc into your optical drive.

 Click the pop-up notification,

then select  to open the installer. If you turn off the AutoPlay

feature from the Windows Control Panel, you can still manually execute the

 from the root path of the MSI Driver Disc.

 The installer will find and list all necessary drivers in the  tab.

 Click the button in the lower-right corner of the window.

 The drivers installation will then be in progress, after it has finished it will prompt

you to restart.

 Click  button to finish.

 Restart your computer.



Before you install utilities, you must complete drivers installation.

 Open the installer as described above.

 Click the  tab.

 Select the utilities you want to install.

 Click the button in the lower-right corner of the window.

 The utilities installation will then be in progress, after it has finished it will

prompt you to restart.

 Click  button to finish.

 Restart your computer.

ページを読み込んでいます...

MSI 7C96 取扱説明書

このマニュアルは次のような方にも適しています

MSI 7C96 取扱説明書

他の言語で

関連論文

その他の書類