D-512-100-11(1)
SU-WL450
Wall-Mount
Bracket
Installation Information
GB
安裝資訊
CT
− 2 (GB) −
Installation Information for
Using Sony Wall-Mount Bracket (SU-WL450)
Supported models:
KD-49X90*G
* In the actual model names, the “” indicates numbers and/or characters specific to each model.
To Customers
For product protection and safety reasons, Sony strongly recommends that installation of your TV
be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.
To Sony Dealers and Contractors
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Sufficient expertise is required for installing this product, especially to determine the
strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment
of this product to the wall to Sony dealers or licensed contractors and pay adequate
attention to safety during the installation. Sony is not liable for any damage or injury
caused by mishandling or improper installation.
For Safety and proper installation, follow the Wall-mount Bracket Operation Instructions, TV Setup
Guide and the directions in this manual.
− 3 (GB) −
GB
On Safety
Thank you for purchasing this product.
To Customers
Sufficient expertise is required for
installing this product. Be sure to
subcontract the installation to Sony
dealers or licensed contractors and pay
special attention to safety during the
installation. Sony is not liable for any
damages or injury caused by
mishandling or improper installation, or
installing any other than the specified
product. Your Statutory Rights (if any) are
not affected.
To Sony dealers
Sufficient expertise is required for
installing this product. Be sure to read
this instruction manual thoroughly to do
the installation work safely. Sony is not
liable for any damages or injury caused
by mishandling or improper installation.
Please give this manual to the customer
after installation.
This instruction manual shows the correct
handling of the product and important
precautions necessary to prevent accidents.
Be sure to read this manual thoroughly and
use the product correctly. Keep this manual
available for future reference.
Products by Sony are designed with safety in
mind. If the products are used incorrectly,
however, it may result in a serious injury
through fire, electric shock, the product
toppling over, or the product dropping. Be
sure to observe the precautions for safety to
prevent such accidents.
CAUTION
Specified products
This Wall-Mount Bracket is designed for use
with the products specified TVs. For TVs,
refer to their Reference Guide to verify that
the Wall-Mount Bracket can be used.
To Customers
WARNING
If the following precautions are not
observed, serious injury or death
through fire, electric shock, or the
product dropping can result.
Be sure to subcontract
the installation to
licensed contractors and
keep small children away
during the installation.
If the Wall-Mount Bracket or the TV is not
installed correctly, the following accidents
may occur. Be sure licensed contractors carry
out installation.
The TV may fall and cause a serious injury
such as a bruise or a fracture.
If the wall on which the Wall-Mount
Bracket is installed is unstable, uneven, or
not perpendicular to the floor, the unit
may fall and cause injury or property
damage. The wall should be capable of
supporting a weight of at least four times
the TV weight.
(Refer to your TV’s Reference Guide for its
weight.)
If the installation of the Wall-Mount
Bracket on the wall is not sufficiently
sturdy, the unit may fall and cause injury or
property damage.
Be sure to subcontract
moving or dismounting
of the TV to licensed
contractors.
If persons other than licensed contractors
transport or dismount the TV, it may fall and
cause injury or property damage. Be sure
that two or more persons (three or more
persons for 75 inches and above TV set) carry
or dismount the TV.
Do not remove screws,
etc., after mounting the
TV.
If you do so, the TV may fall and cause injury
or property damage.
Do not make alterations
to the parts of the Wall-
Mount Bracket.
If you do so, the Wall-Mount Bracket may fall
and cause injury or property damage.
Do not mount any
equipment other than
the specified product.
This Wall-Mount Bracket is designed for use
with the specified product only. If you mount
equipment other than specified, it may fall or
break, and cause injury or property damage.
Do not apply any load
other than the TV on the
Wall-Mount Bracket.
Do not shake the TV left/
right, up/down.
If you do so, the TV may fall and cause injury
or property damage.
Do not lean on or hang
from the TV.
Do not lean on or hang from the TV as it may
fall on you and cause serious injury.
CAUTION
If the following precautions are not
observed, injury or property damage
may occur.
Do not handle the
product with excessive
force during cleaning or
maintenance.
Do not apply excessive force on the topside
of the TV. If you do so, the TV may fall and
cause injury or property damage.
Precautions
If you use the TV installed on the
Wall-Mount Bracket for a long time, the
wall behind or above the TV may become
discolored or the wallpaper may come
unstuck, depending on the material of the
wall.
If the Wall-Mount Bracket is removed after
installing it on the wall, the screw holes are
left.
Do not use the Wall-Mount Bracket in a
place where it is subjected to mechanical
vibrations.
Installing the Wall-
Mount Bracket
To Sony Dealers
WARNING
The following instructions are for Sony
dealers only. Be sure to read safety
precautions described above and pay
special attention to safety during the
installation, maintenance and checking
of this product.
Do not install the Wall-
Mount Bracket on wall
surfaces where the
corners or the sides of
the TV protrude away
from the wall surface.
− 4 (GB) −
Do not install the Wall-Mount Bracket on wall
surfaces such as a pillar, where the corners
or the sides of the TV protrude away from
the wall surface. If a person or object
happens to hit the protruded corner or side
of the TV, it may cause injury or property
damage.
Do not install the TV over
or under an air-
conditioner.
If the TV is exposed to water leaks or air
current from an air conditioner for a long
time, it may cause a fire, an electric shock or
a malfunction of the TV.
Be sure to install the
Wall-Mount Bracket
securely to the wall
following the instructions
in this instruction
manual.
If any of the screws are loose or fall out, the
Wall-Mount Bracket may fall and cause injury
or property damage. Be sure to use the
appropriate screws for the material of the
wall and install the unit securely using four
or more screws of 8 mm diameter (or
equivalent).
Be sure to use the
supplied screws and
attachment parts
properly following the
instructions given in
this instruction
manual. If you use
substitute items, the
TV may fall and cause
bodily injury to
someone or damage to
the TV.
Be sure to assemble the
bracket properly
following the instructed
procedure explained in
this instruction manual.
If any of the screws are loose or fall out, the
TV may fall and cause bodily injury to
someone or damage to the TV.
Be sure to tighten the
screws securely in the
designated position.
If you fail to do so, the TV may fall and cause
bodily injury to someone or damage to the
TV.
Be careful not to subject
the TV to shock during
installation.
If the TV is exposed to shock, it may fall or
break apart. This may cause injury.
Be sure to install the TV
on a wall that is both
perpendicular and flat.
If you fail to do so, the TV may fall and cause
injury.
After proper installation
of the TV, secure the
cables properly.
If people or objects get tangled with cables,
this may result in injury or damage to the TV.
Do not allow the AC
power cord (mains lead)
or the connecting cable
to be pinched.
If the AC power cord (mains lead) or the
connecting cable is pinched between the
unit and the wall or is bent or twisted by
force, the internal conductors may become
exposed and cause a short circuit or an
electrical break. This may cause a fire or an
electric shock.
The screws needed to
secure the Wall-Mount
Bracket to the wall are
not supplied.
Use the appropriate screws for the wall
material and structure when mounting the
Wall-Mount Bracket.
− 5 (GB) −
GB
Installing the TV onto the
wall
Installation procedure differs, depending on
your TV.
Use the Wall-Mount Bracket SU-WL450 to
install the TV to the wall.
Note
Be sure to store the removed screws in a safe place,
keeping them away from children.
Preparing for installation
Have the TV’s Reference Guide and Setup
Guide at hand before installation.
Be sure to have a Phillips screwdriver that
fits the screws prior to the assembly.
Confirm the installing position of your TV.
Prepare four or more screws of 8 mm
diameter and one screw of 5 mm or
equivalent (not supplied). Select screws
suitable for the material of the wall.
Checking the parts
Supplied with SU-WL450
Verify that all the parts are included.
Base (20) (1) Pulley (2)
PSW 6x20 (4) PSW 4x20 with
Bush (2)
Spacer (20) (2) Belt (1)
Bush (20) (M4) (2) PSW 4x20 (2)
Base Adaptor (2) PSW 4x10 (8)
Spacer (60) (2) PSW 6x50 (2)
Bush (M4) (2) PSW 4x50 (2)
− 6 (GB) −
Deciding on the installation location
1 Decide on the installation location.
Make sure that the wall has enough space for the TV and is capable of supporting a weight of at
least four times that of the TV.
Refer to the following table on installing the TV to the wall. Refer to your TV’s Reference Guide
for the TV’s weight.
Screen centre point
Standard mounting Slim mounting
Unit: mm
Model Name
Display dimensions
Screen
centre
dimension
Length for mounting
Standard
mounting
Slim
mounting
KD-49X90G
1,093 629 163 480 132 90
Note
Figures in the table may differ slightly depending on the installation.
When your TV is installed on the wall, the upper side of the TV slightly leans forward.
− 7 (GB) −
GB
Allow for suitable clearance between the
TV and the ceiling and protruding parts of
the wall as shown below.
Unit: mm
300100
100 100
To ensure proper ventilation and prevent the
collection of dirt or dust:
ˋ Do not lay the TV set flat, install upside down,
backwards, or sideways.
ˋ Do not place the TV set on a shelf, rug, bed or in a
closet.
ˋ Do not cover the TV set with a cloth, such as
curtains, or items such as newspapers, etc.
ˋ Do not install the TV set as shown below.
Air circulation is blocked.
Wall
Note
If you intend to route the cables in the wall, make a
hole in the wall to insert the cables before beginning
the installation.
To prevent pinching the cables, prepare a hole in the
wall somewhere outside the perimeter of the Base
(20) , Base Adaptor and Spacer (20) , Spacer
(60) .
2 Select Wall mounting style. It is
selectable as shown below.
2-a Standard mount
2-b Slim mount
Refer to the table of step 1.
WARNING
When 2-b is selected, rear terminal access is limited.
2-a 2-b
3 Refer to the below table about
the Base Adaptor fitting
location. In case of selecting
2-b, then skip this step.
Model Name Hook location
KD-49X90G
c
a
d
b
c
− 8 (GB) −
Fit Base Adaptor by using
Screw (PSW 4x10) to Base
(20) when selecting 2-a.
4 Decide the positions of the
screws for installing the Base
(20) .
Refer to the specifications on page 13.
When selecting 2-a, please use the hole
positions of Base Adaptor .
WARNING
The wall that the TV will be mounted on should be
able to support a weight of at least four times that of
the TV (Refer to your TV’s Reference Guide for its
weight.).
Determine the strength of the wall the TV will be
mounted on. Reinforce the wall sufficiently, if
necessary.
Installing the Base on the
wall
Use four or more screws of 8 mm diameter
or equivalent (not supplied).
Fit four screws to the holes of Base
Adaptor with Base (20) (2-a only).
Install the Base (20) on the wall
horizontally.
2-a
2-b
− 9 (GB) −
GB
Slim mounting (2-b)
Belt
Screw (+PSW 6 x 20)
Pulley
Spacer (20 mm)
3 Connect the necessary cable(s)
to the TV.
Make sure to connect the cables before
installing the TV on the wall. You will be
unable to connect the cables when the TV
is installed.
Refer to the Reference Guide supplied with
your TV.
Note
Subcontract the cable routing in the wall to a licensed
contractor.
Bundle the connecting cables to prevent stepping on
them before wall mounting.
4 Detach the Table-Top Stand
from the TV.
Note
Be careful when lifting the TV as the Table-Top Stand
is detached, the Table-Top Stand may topple over
and cause personal injury.
Take care when removing the Table-Top Stand from
the TV to prevent it from falling over and damaging
the surface that the TV is sitting on.
Preparing for the installation
of the TV
Refer to the Setup Guide for stand installation.
1 Remove the screws from the
rear of the TV.
2 Attach the Attachment parts for
Wall-Mount Bracket. Check the
Attachment parts by referring to
“Supplied with SU-WL450” in
“Checking the parts” on page
5.
Note
Firmly secure the Attachment parts using screws.
When using an electric screwdriver, set the torque
setting to approximately 1.5 N·m {15 kgf·cm}.
Be sure to store the used or unused parts in a safe
place for future use. Retain this manual for future
reference.
Standard mounting (2-a)
Belt
Spacer
(60 mm)
Screw (+PSW 6 x 50)
Pulley
Screw
(+PSW 6 x 20)
− 10 (GB) −
2 Install the TV onto the Base or
Base Adaptor.
Gently slide down the TV and hang the
Pulleys attached to the rear of the TV
to the Base or Base Adaptor, making
sure to confirm the shape of the holes.
After installing the TV on the wall,
confirm the Pulleys are firmly latched
into the Base or Base Adaptor.
Release both hands slowly to ensure
that the TV does not fall.
Installing the TV on the wall
1 Lift the TV.
For the location of the Pulleys to the
hang on the Base or Base Adaptor, refer
to the table of step 3 in “Deciding on the
installation location” on page 7.
Make sure that the rear of the TV
touches the Base or Base Adaptor when
holding the TV.
Note
Hold the TV securely with both hands.
− 11 (GB) −
GB
2-b
2-a
− 12 (GB) −
WARNING
Be sure that two or more persons (three or more
persons for 75 inches and above TV set) hold the TV
when carrying it.
3 Preventing the bottom of the TV
from shifting.
Take up the slack of Belt and attach it
to the wall tightly.
2-a 2-b
Use a 5 mm diameter screw or
equivalent (not supplied).
Note
Try to pull the bottom of the TV towards yourself
slightly, to make sure that it does not move forward.
If there is any movement, it is not fixed correctly, and
the Belt should be secured firmly again.
− 13 (GB) −
GB
Confirming the completion of
the installation
Check the following points.
The Pulleys are firmly hung onto the Base
or Base Adaptor.
The cord and the cable are not twisted or
pinched.
The Belt is tight with no slack.
WARNING
Improper placement of the AC power cord (mains lead),
etc. may cause fire or electric shock through a short
circuit. Be sure to confirm the completion of the
installation for safety.
Other information
When removing the TV, reverse the previous
installation procedure.
WARNING
Be sure that two or more persons (three or more persons
for 75 inches and above TV set) hold the TV when
removing it.
Specifications
f
c
d
b
a
g
e
h2h1
Dimensions: (Approx.) [mm]
a : 400
b : 300
c : 200
d : 100
e : 80
f : 480
g : 100
h1 : 20 (case 2-b)
h2 : 60 (case 2-a)
Weight (base only): (Approx.) [kg]
0.8
Design and specifications are subject to change without
notice.
− 2 (CT) −
使用 Sony 壁掛式支架之安裝訊息 (SU-WL450)
支持型號:
KD-49X90
*
G
* 在實際的型號名稱中，“”指的是每種型號特有的數字和/或字元。
致用⼾
為保護產品和安全理由，Sony 強烈建議安裝您的電視的任務由 Sony 經銷商或授權承包商進行。請勿試
圖自行安裝。
致 Sony 經銷商和承包商
請在安裝、定期維修和檢查本產品時特別注意安全。
安裝本產品，尤其是在確定牆壁強度是否能夠支撐電視機重量方面，需要足夠的專業知識。
將本產品安裝於牆上的工作務必要委託 Sony 經銷商或經過授權的承包商進行，而且安裝時
要特別注意安全。Sony 對於任何因為錯誤操作或不當安裝所造成的損壞或傷害恕不負責。
為確保安全正確安裝，請遵循壁掛式支架之使用說明書、電視安裝指南及本手冊內說明。
CT
− 3 (CT) −
安全事項
感謝您購買本產品。
致用⼾
安裝本產品需要足夠的專業技術。請務必
委由 Sony 經銷商或經授權的承包商進行
安裝，且安裝期間需特別注意安全。Sony
對操作不當或安裝不正確，或安裝任何⾮
指定產品而引起的任何損壞或傷害概不負
責。任何相關的法律權利將不受影響。
致 Sony 經銷商
安裝本產品需要足夠的專業技術。請務必
詳讀本說明書，以確保安裝本產品時之安
全。Sony 對因錯誤操作或不當安裝所造成
的任何損壞或傷害，概不承擔責任。請在
安裝後將本手冊交給用⼾。
本說明書介紹了正確使用本產品與防⽌事故發
⽣需知的重要事項。請務必詳讀本手冊，以確
保正確使用本產品。請妥善保管本手冊，以備
將來參考。
Sony 的產品設計⾮常注重安全。但是，如果使
用不正確，則可能因⽕災、電擊、產品傾倒或
墜落而導致嚴重傷害。請務必遵守安全事項，
以防⽌此類事故發⽣。
⼩⼼
特定產品
本壁掛式支架設計用於指定產品的電視機。有
關電視機，請參考其參考指南以確認是否可使
用本壁掛式支架。
致用⼾
警告
如果不遵守下列事項，則可能因⽕災、電
擊或產品墜落而導致嚴重傷害或死亡。
請務必將安裝工作委託經授
權的承包商，並且避免安裝
過程中讓孩童接近。
如果壁掛式支架或電視機安裝不正確，則可能
發⽣下列事故。因此請確保安裝工作由經授權
的承包商進行。
電視機可能會掉落，而造成嚴重的傷害，如
挫傷或⾻折等。
如果安裝壁掛式支架的牆壁不穩固、凹凸不
平、或未與地面垂直，裝置可能會掉落，因
而造成傷害或財產損失。牆壁應能承受⾄少
四倍於電視機的重量。
(有關您電視機的重量，請參考電視機的參考
指南。)
如果牆壁上安裝的壁掛式支架不夠牢固，則
裝置可能會掉落，並造成傷害或財產損失。
請務必將搬動或拆卸電視機
的工作委由經授權的承包商
進行。
如果由未經授權的承包商搬動或拆卸電視機，
裝置可能會掉落，造成傷害或財產損失。確保
由兩人或更多人（75 吋及以上電視機需要三人
或更多人）搬運或拆卸電視機。
安裝電視機之後請勿拆除任
何螺絲等零件。
否則，電視機可能會掉落，造成傷害或財產損
失。
請勿改裝壁掛式支架的零
件。
否則，壁掛式支架可能會掉落，造成傷害或財
產損失。
請勿將指定產品之外的其他
設備安裝到支架上。
本壁掛式支架僅爲安裝特定產品而設計。如果
您安裝⾮特定設備，則設備可能會掉落或破
裂，造成傷害或財產損失。
除了電視機之外，請勿在壁
掛式支架上加掛其他重物。
請勿左右或上下搖晃電視
機。
否則，電視機可能會掉落，造成傷害或財產損
失。
請勿倚靠或攀爬電視機。
請勿倚靠或攀爬電視機，因爲裝置可能會掉落
在您⾝上，造成嚴重傷害。
⼩⼼
如果不遵守下列事項，則可能造成傷害或
財產損失。
清潔或維修過程中，請勿對
產品施加過⼤的⼒量。
請勿在電視機頂部施加過⼤的⼒量。否則，電
視機可能會掉落，造成傷害或財產損失。
注意事項
⾧期使用安裝於壁掛式支架的電視機時，視
牆面的材料而定，可能會造成電視機後方或
上方的牆面褪⾊，或是壁紙脫落。
在牆壁上安裝壁掛式支架後再將其拆下，牆
壁上會留下螺絲孔。
請勿在容易受到機械振動的地方使用壁掛式
支架。
安裝壁掛式支架
致 Sony 經銷商
警告
下列說明僅適用於 Sony 經銷商。請務必
閱讀上述安全注意事項，並在安裝、維修
和檢查本產品時特別注意安全。
請勿將壁掛式支架安裝在會
使電視機邊⾓或側面突出於
牆面的牆壁位置。
請勿將壁掛式支架安裝在柱⼦等會使電視機邊
⾓或側面突出於牆面的牆壁位置。如果人或物
品正巧撞到電視機的邊⾓或側面，則會造成傷
害或財產損失。
請勿將電視機安裝在冷氣機
的上方或下方。
如果電視機⾧期暴露於冷氣機的漏⽔或氣流
中，可能造成⽕災、電擊或電視機故障。
− 4 (CT) −
請務必依照本說明書中的指
⽰，牢固地將壁掛式支架安
裝於牆上。
如果有螺絲鬆動或掉落，壁掛式支架可能會掉
落，造成傷害或財產損失。針對不同牆壁材
料，請務必使用正確的螺絲，並使用四個或更
多個直徑 8 毫米（或相等規格）的螺絲牢固地
安裝本裝置。
請務必按照本使用說明書
中的指⽰，正確使用所提
供的螺絲和附件。如果使
用其他替代零件，電視機
可能會掉落，造成人員的
受傷或損壞電視機。
請務必按照本使用說明書中
介紹的步驟，正確安裝支
架。
如果有螺絲鬆動或掉落，電視機可能會掉落，
並造成人員的受傷或損壞電視機。
請務必在指定的位置上，將
螺絲安全地鎖緊。
否則，電視機可能會掉落，造成人員的受傷或
損壞電視機。
安裝的過程中，請務必⼩⼼
不要讓電視機遭到衝撞。
如果電視機遭到衝撞，可能會掉落或破裂。並
可能造成傷害。
請務必將電視機安裝在垂直
且平坦的牆面上。
否則，電視機可能會掉落，並造成傷害。
正確安裝電視機後，請確實
固定電纜。
如果人或物品勾到電纜，可能會造成傷害或損
壞電視機。
請勿使交流電源線或連接電
纜受到擠壓。
如果交流電源線或連接電纜被壓在裝置和牆壁
之間，或被用⼒彎曲或扭曲，其內部導線可能
會因裸露而短路或斷電。如此可能會引起⽕災
或電擊。
不提供用於將壁掛式支架固
定於牆壁的螺絲。
在安裝壁掛式支架時，請使用適合牆壁材料和
結構的螺絲。
CT
− 5 (CT) −
將電視機安裝⾄牆上
視電視機而定，安裝步驟可能不同。
使用壁掛式支架 SU-WL450，將電視機安裝⾄牆
壁上。
註
請務必將取下的螺絲放置在安全的地方，讓螺絲遠離兒童。
準備安裝
安裝前，請將電視機的參考指南和安裝指南放
在手邊。
組裝前，請務必使用適合螺絲的⼗字螺絲起
⼦。
確認電視機的安裝位置。
準備四個或更多個直徑 8 毫米和⼀個直徑
5 毫米或相等規格的螺絲（不提供）。請選擇
適合牆壁材料的螺絲。
檢查零件
SU-WL450 隨附組件
確認零件是否完整。
底座（20）(1) 滑輪 (2)
PSW 6x20 (4) 帶襯套的
PSW 4x20（2）
墊⽚ (20) (2) ⽪帶 (1)
襯套 (20) (M4)
(2)
PSW 4x20 (2)
底座轉接器 (2) PSW 4x10 (8)
墊⽚ (60) (2) PSW 6x50 (2)
襯套 (M4) (2) PSW 4x50 (2)
− 6 (CT) −
確定安裝位置
1 確定安裝位置。
確保牆壁有足夠的空間予電視機以及能支撐⾄少電視機四倍的重量。
請參閱以下列表有關在牆上安裝電視機。有關電視機的重量，請參閱電視機的參考指南。
標準安裝
簡易安裝
螢幕中⼼點
單位：毫米
型號名稱
顯⽰幕 幕中⼼尺寸 安裝的⾧度
標準安裝 簡易安裝
KD-49X90G
1093 629 163 480 132 90
註
製表內的數字視安裝而可能略有不同。
當您的電視機安裝在墻上時，電視機的上部稍微向前傾。
CT
− 7 (CT) −
在電視機與天花板，以及牆面突出的部分之
間騰出適當的空間，如下所⽰。
單位：毫米
300
100
100 100
為了確保正確通風及防⽌髒物或灰塵堆積：
ˋ 請勿將電視機平放、上面朝下安裝、向後安裝或側面
安裝。
ˋ 請勿將電視機放置於架⼦、地毯、床或壁櫥中。
ˋ 請勿用布（如窗簾）或物件（如報紙等）覆蓋電視
機。
ˋ 請勿如下圖所⽰安裝電視機。
通風受阻。
牆面
註
如果您想要將電纜放置在牆壁中，在開始安裝前，必須
在牆壁中鑽⼀個孔用以插⼊電纜。
為了避免夾住電纜，請在底座 (20) ，底座轉接器
和墊⽚ (20) ，墊⽚ (60) 邊緣外的牆壁上鑽
⼀個孔。
2 選擇壁掛式安裝樣式。有如下幾
種可供選擇。
2-a 標準安裝
2-b 簡易安裝
請參閱步驟 1 的表格。
警告
選擇 2-b 時，背後端⼦的使用受到限制。
2-a
2-b
3 有關底座轉接器的安裝位置，請
參閱下表。如果選擇 2-b，則跳
過此步驟。
型號名稱 掛鉤位置
KD-49X90G
c
a
d
b
c
− 8 (CT) −
選擇 2-a 時，使用螺絲（PSW
4x10） 將底座轉接器 安裝
到底座 (20) 上。
4 確定安裝底座 (20) 的螺絲位
置。
請參考第 13 ⾴的規格。
選擇 2-a 時，請使用底座轉接器 的各孔
位置。
警告
安裝電視機的牆壁應能承受⾄少四倍於電視機的重量(有
關您電視機的重量，請參考電視機的參考指南。）。
請確定要安裝電視機的牆壁強度。如有必要，請適當加
固牆壁。
將底座安裝⾄牆上
使用四個或更多個直徑 8 毫米或相等規格的
螺絲（不提供）。
將四顆螺絲固定在已經和底座（20） 相連
的底座轉接器 各孔中（僅 2-a）。
在牆壁上⽔平安裝底座 (20) 。
2-a
2-b
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
