Dell UPS 2700R クイックスタートガイド

Dellt Online Rack UPS

2700W

Getting Started With

Your System

Démarrage avec votre système

Erste Schritte Mit Ihrem System

Начало работы c вашей системой

Inicio de su sistema

系统使用入门指南

系統使用入門指南

사용자의 시스템 시작하기

K803N , H950N, J728N

H967N

www.dell.com | support.dell.com

Dellt Online Rack UPS

2700W

Getting Started

With Your System

K803N , H950N, J728N

H967N

www.dell.com | support.dell.com

Notes and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your software.

CAUTION: A CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury or in property damage incidents.

WARNING: A WARNING indicates a potentially hazardous situation which, if not avoided, could result in death o r

injury.

DANGER: A DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

DANGER: Observe the following instruction to help prevent an imminently hazardous situation which, if not

avoided, will result in death or serious injury:

S This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by

AUTHORIZED SERVICE PERSONNEL ONLY.ThereareNO USER SERVICEABLE PARTS

inside the UPS.

Informationinthisdocumentissubject to change without notice.

E 2009 Dell Inc. All r ights reserved.

Reproduction in any manne r whatsoever without the written permission of Dell Inc. is strictly forbidde n.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc., Phillips is a reg istered trademark of Phillips Screw

Company.

Other trademarks and trade names may be used in this document to refer to eithe r the entities claiming the ma rks and names or their

products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

July2009

3

System Features

|

System Features

Providing outstanding performance and reliability, the UPS's unique benefits include:

S Online UPS design with pure sine wave output. The UPS filters and regulates incoming AC power

and provides consistent power to your equipment without draining the battery.

S True online double-conversion technology with high power density, utility frequency

independence, and generator compatibility.

S Selectable High Efficiency mode of operation.

S 4U size that fits any standard 48 cm (19”) rack.

S Start-on-battery capability for powering up the UPS even if utility power is not available.

S Extended runtime with an optional External Battery Module (EBM) for 2700W UPS models.

S Emergency shutdown control through the Remote Emergency Power-off (REPO) ports.

S Two standard communication ports (USB and DB-9 serial port).

S Optional Dell Network Management Card with enhanced communication capabilities for

increased power protection and control.

S Advanced power management with the Dell UPS Management Software for graceful shutdowns

and power monitoring.

S Sequential shutdown and load management through separate receptacle groups called load

segments.

S Firmware that is easily upgradable without a service call.

S Backed by worldwide agency approvals.

4

|

Finding Information

CAUTION: The Safety, Environmental, and Regulatory Information document provides important safety and

regulatory information.

What are You Looking For?

Find It Here

S The user's guide for my UPS

S The user's guide for the Dell Network Management

Card

S Dell UPS Management Software

NOTE: Documentation and software updates can be

found at

support.dell.com.

Dell UPS Disc

S Specifications

S How t o configure UPS settings

S How to troubleshoot and solve problems

S How to install REPO control

Dell UPS User's Guide

The user's guide is available on the Dell UPS disc and

on support.dell.com.

S Safety instructions

S Regulatory information

S Recycling information

Safety, Environmental, and Regulatory Information

S Warranty information

S Terms and Conditions (U.S. only)

S End User License Agreement

Dell Warranty and Support Information

S Support information Dell Support Website — support.dell.com

NOTE: Select your region or business segment to view

the appropriate support site.

5

Installation and Startup

|

Installation and Startup

CAUTION: Before performing the procedures in this document, read and follow the safety instructions and

important regulatory information in your Safety, Environmental, and Regulatory Information document.

This section describes the steps to set up your system for the first time.

Unpacking the System

1 Open the outer carton and remove the accessories packaged with the cabinet.

6

|

Installation and Startup

Lifting the Cabinet

CAUTION: The cabinet is heavy (36.9 kg/81.4 lb). Lifting the cabinets into the rack requires a minimum of two

people.

1 Withonepersononeachside,carefullyliftthecabinet out of the outer carton using the handles

on the cardboard and set it on a flat, stable surface.

2 Discard or recycle the packaging in a responsible manner, or store it for future use.

7

Installation and Startup

|

Identifying the UPS

This section shows a front and rear panel of the Dell Online Rack UPS. Refer to the Dell Online Rack

UPS 2700W User's Guide for all rear panel details.

On/Off Button

LCD Panel

Scroll Button (Down or Forward)

Select Button

Scroll Button (Up or Back)

Figure 1. The Dell Online Rack UPS Front Panel

UPS

Communication Bay

2m, L5-30P Input

Cord

USB Port

One L5-20 and Two 5-15/5-20

Receptacles

(Load Segment 1)

REPO Ports

RS-232 Port

Ground Screw

Two IEC 320-C13

Receptacles

(Load Segment 2)

EBM Connector

Cover/Strain Relief Bracket

Figure 2. UPS Rear Panel (2700W, 120V Shown)

8

|

Installation and Startup

Rackmount Setup

CAUTION: The cabinet is heavy (36.9 kg/81.4 lb): 1) Dell strongly recommends to remove the battery tray from

the UPS before lifting. 2) Lifting the cabinets into the rack requires a minimum of two people.

CAUTION: Removing the batteries should be performed or supervised by personnel knowledgeable about

batteries and the required precautions. Keep unauthorized personnel away from batteries.

Opening the Battery Cover

1 Loosen the thumbscrew on the metal battery cover, slide the cover to the right, and open.

9

Installation and Startup

|

Removing the Battery Tray

2 Disconnect the battery connector and place the right battery connector in the battery door to

move it out of the way.

3 Pull the battery tray out using the plastic tabs and remove the battery tray.

10

|

Installation and Startup

Positioning the Rails

NOTE: The instructions are the same for square-hole racks and unthreaded, round-hole racks. The rails fit both

rack styles. The round-hole rack is shown in the illustrations.

4 Select the proper holes in the rail for positioning the UPS in the desired location in the rack.

The rails should be located at the bottom of the 4U space allocated for the UPS or 3U for the

EBM.

5 Position the end of the left and right rails labeled L and R facing inward.

11

Installation and Startup

|

Attaching the R ails to the Rack

6 Attach the rails to the rack:

Adjust the rail so that the flanges fit outside the C-shaped vertical rail.

Secure the rail using the supplied #12-24 Phillips head screws (four for each rail). Use the bottom

two holes for the front of the rail. Use the second and fourth holes for the back of the rail.

NOTE:

If the vertical rail has square holes, use a square nut (not supplied) with the supplied #12-24

Phillips-head screw.

12

|

Installation and Startup

Installing and Securing the Cabinet

7 Slide the cabinet into the rack.

8 Secure the cabinet to the rack using the supplied #12-24 Phillips-head screws (two on each side).

9 Repeat for any additional cabinets.

13

Installation and Startup

|

Installing the Battery Tray

NOTE: A small amount of arcing may occur when connecting the batteries. This is normal and does not damage

the unit or present any safety concern.

10 Remove the right battery connector from the door and connect the internal battery connector.

11 Close the metal battery cover.

Adjust the battery connector so that the door closes properly. Push the door slightly to the right

and then to left.

12 Tighten the thumbscrew.

Torque the screw to 0.7 Nm (6.2 lb in).

14

|

Installation and Startup

Installing the UPS Front Cover

13 Install the UPS front cover.

Connecting the Equipment

1

If you plan to use Dell UPS Management Software, connect your computer to the USB port using

the supplied cable.

2 If your rack has conductors for grounding or bonding of ungrounded metal parts, connect the

ground cable (not supplied) to the ground bonding screw.

3 If an emergency power-off (disconnect) switch is required by local codes, see “Installing Remote

Emergency Power-off” (REPO) in the Dell Online Rack UPS 2700W User's Guide.

4 Plug the equipment to be protected into the UPS output receptacles, but do not turn on the

protected equipment.

NOTE:

Verify that the total equipment ratings do not exceed the UPS capacity to prevent an overload alarm.

15

Installation and Startup

|

Connecting the Power Cord

5 Verify that the power input to the UPS has adequate upstream overcurrent protection:

Table 1. Minimum Upstream Circuit Breaker Rating

UPS Output Power

120V 208V 230V

2700W 30A 20A 16A

6 For models with a detachable power cord. Plug the detachable UPS power cord into the input

connector on the UPS rear panel.

7 Plug the UPS power cord into a power outlet.

16

|

Installation and Startup

Starting the UPS

8 Press the button on the UPS front panel.

Completing the Startup

9 Verify that the Normal icon appears on the UPS status summary screen, indicating that the

UPS is operating normally and any loads are powered.

10 On the UPS status summary screen, press the button to check for active alarms or notices.

Resolve any active alarms before continuing. See “Troubleshooting” in the Dell Online Rack UPS

2700W User's Guide.

If there are no active alarms, a “No Active Alarms” message appears.

11 To change other factory-set defaults, see “Operation” in the Dell Online Rack UPS 2700W User's

Guide.

Onduleur en Baie En Ligne Dellt

2700 W

Démarrer

avec votre système

K803N , H950N, J728N

H967N

www.dell.com | support.dell.com

Remarques et avertissements

REMARQUE : Une REMARQUE indique des informations importantes qui vous aident à mieux utiliser votre logiciel.

MISE EN GARDE : Une MISE EN GARDE indique une situation dangereuse potentielle qui, si elle n'est pas évitée,

peut provoquer une blessure mineure ou modérée ou des dommages matériels.

AVERTISSEMENT : Un AVERTISSEMENT indique une situation dangereuse potentielle qui, si elle n'est pas évitée,

pourrait provoquer la mort ou une blessure.

DANGER : Un DANGER indique une situation dangereuse imminente qui, si elle n'est pas évitée, provoquera la

mort ou une blessure grave.

DANGER : Respectez les instructions suivantes pour aider à empêcher une situation dangereuse qui, si elle n'est

pas évitée, peut provoquer la mort ou des blessures graves :

S Cet onduleur contient des TENSIONS MORTELLES. Toutes les réparations et tous les entretiens

devront être effectués UNIQUEMENT PAR UN PERSONNEL D’ENTRETIEN AGRÉÉ. Aucune

pièce à l’intérieur de cet onduleur NE PEUT ÊTRE ENTRETENUE PAR L’UTILISATEUR.

Les informations figurant dans ce document sont soumises à modification sans préavis.

La reproduction de quelque manière que ce soit sans l’autorisation écrite de Dell Inc. est strictement interdite.

Marques commerciales utilisées dans c e texte : Dell et le logo DELL sont des marques commerciales de Dell Inc. ; Phillips est une marque

commerciale de Phillips Screw Company.

D’autres marques commerciales et noms commerciaux peuvent être utilisés dans ce document pour se référe r à des entités revendiqua nt le s

marques et les noms ou à leurs produits. Dell Inc. nie tout intérêt propriétaire dans les marques commerciales et les noms commerciaux qui

ne lui appartenant pas.

Julliet 2009

ページを読み込んでいます...

Dell UPS 2700R クイックスタートガイド

関連論文