● 规格参数
● 名称：无线蓝牙耳机
● 型号：sanag Z36S Pro
● 连接范围：≥10米
● 蓝牙版本：V 5.3
● 耳机电池容量：35mAh
● 充电仓电池容量：250mAh
● 充电时间：约1小时
● 产品概述
● 蓝牙配对
1.打开充电仓，耳机自动开机；请将蓝牙耳机和手机（或其他的连接设备）
的距离在 50CM的范围内，越近越好。
● 耳机功能操作说明
1.耳机MFB键
● 开机：自动开机，翻开充电盒盖子两边耳机自动开机进入组对状态。手动开机，
长按MFB触摸键约3秒。白蓝灯快闪，连接后熄灭
● 关机：自动关机，耳机放入充电盒并合上盖子进入充电状态自动关机断开连接。
手动关机，暂停播放时长按MFB键触摸约7秒。白蓝灯快闪3下后熄灭
4.LED灯
2.喇叭出音孔
5.Type-C充电口
3.充电触点
6.充电仓指示灯
-1- -2- -3-
2.打开手机蓝牙界面，搜索”sanag Z36S Pro“，点击配对，连接设备。
搜索耳机 连接成功
设置
我的设备
sanag Z36S Pro sanag Z36S Pro
设置
我的设备
连接
使用指南
User Guide
TRUE WIRELESS STEREO
● 配对状态：耳机开机后自动进入配对状态，组对成功，主耳白蓝灯交替闪，
副耳不亮灯。
● 耳机与手机配对：左右耳机互连成功状态下，打开手机蓝牙并在蓝牙列表中找到
设备名,点击连接，连接成功灯灭。
● 断开连接：从手机蓝牙列表断开耳机或关闭手机蓝牙功能，主耳白蓝灯交替闪，
副耳不亮灯。
● 播放/暂停：任意单击左右耳MFB触摸键。
● 音量＋：三击左耳MFB触摸键。
● 音量－：三击右耳MFB触摸键。
● 上一曲：双击左耳MFB触摸键。
● 下一曲：双击右耳MFB触摸键。
● 来电接听：来电时，任意单击左右耳MFB触摸键。
● 挂断电话：通话中，任意双击左右耳MFB触摸键。
● 拒绝接听：来电时，任意长按左右耳2秒MFB触摸键。
● 启动语音助手：任意长按3秒左右耳MFB触摸键松开进入语音助手, 单击退出。
● 霍尔功能:耳机充电时，放入充电仓，合上充电仓盖子盒子给耳机充电的指示灯
亮起，蓝灯常亮。耳机充满，盒子灭灯，耳机灭灯。
● 配对超时：开机未连接手机时，5分钟后自动关机。
● 复位耳机：开机未连接手机时任意5击左右耳MFB键复位耳机出厂设置。复位成功
白蓝灯亮2秒后自动关机。
● 注意事项
●
切勿使用具有磨蚀性的清洁剂清理本产品。
●
切勿让本产品加热或靠近火源，如煮食炉。
●
切勿让本产品长时间受阳光直接照射。
●
切勿将本产品弃置于火中，避免发生爆炸。
●
切勿尝试拆开本产品作出任何修改，因为它并不包含任何维修组件。
●
切勿在雨中使用本产品。
●
如果长时期内不打算使用本产品，请您将它储存在干燥的环境中，并每月至
少为耳机充电一次以延长寿命，避免极端的温度和灰尘。
sanag Z36S Pro TWS蓝牙耳机
2
4
5
6
1
● Product Overview ● Bluetooth pairing
1. Open the charging bin, and the headset will start automatically; Please
connect Bluetooth headset and mobile phone (or other connecting devices)
The distance is within the range of 50CM, the closer the better.
● Headphone function operation instructions
1.Headphone MFB key
● Power on: automatically power on, turn on the earphones on both sides of
the charging box cover and enter the pairing state automatically.
Start the machine manually, press and hold the MFB touch key for
about 3 seconds. The white and blue light flashes quickly and goes
out after connecting.
● Shut down: automatically shut down, put the headset into the charging box
and close the cover to enter the charging state, automatically shut
down and disconnect. Turn off the machine manually, and press
the MFB key for about 7 seconds when pausing playback. The
white and blue light will flash three times and then go out.
4.LED light
2.Speaker outlet
5.Type-C charging port
3.Charging contact
6.Charging chamber indicator
-1- -2- -3-
2.Open the Bluetooth interface of the mobile phone, search for "sanag Z36S
Pro", and click Pair to connect the device.
Search headset Connection succeeded
Settings
MY DEVICES
sanag Z36S Pro sanag Z36S Pro
Settings
MY DEVICES
Connected
● Specifications
● Name: Wireless Bluetooth headset
● Model：sanag Z36S Pro
● Connection range: ≥ 10m
● Bluetooth version: V 5.3
● Headphone battery capacity: 35mAh
● Battery capacity of charging bin: 250mAh
● Charging time: about 1 hour
● matters needing attention
●
Do not use abrasive cleaners to clean this product.
●
Do not allow this product to be heated or close to fire sources, such
as cooking stoves.
●
Do not expose this product to direct sunlight for a long time.
●
Do not dispose this product in the fire to avoid explosion.
●
Do not attempt to disassemble this product to make any modifications,
as it does not contain any repair components.
●
Do not use this product in the rain.
●
If you do not intend to use this product for a long time, please store it
in a dry environment and charge the headset at least once a month to
prolong its life and avoid extreme temperature and dust.
FCC ID: 2A6MSZ36SPRO
● FCC Statement
● This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.Any Changes or modifications not
expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
● Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However
, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
-3-
-2-
● Pairing status: The headset will automatically enter the pairing status after it
is turned on. Pairing is successful, the white and blue lights in the main ear
flash alternately, and the auxiliary ear does not light.
● Pair the headset with the mobile phone: When the left and right headphones
are connected successfully, open the mobile phone Bluetooth and find the
device name in the Bluetooth list. Click Connect, and the connection success
light goes out.
● Disconnect: disconnect the headset from the Bluetooth list of the mobile
phone or turn off the Bluetooth function of the mobile phone. The white
and blue lights in the main ear flash alternately, and the auxiliary ear does
not light up.
● Play/Pause: Click the MFB touch keys on the left and right ears.
● Volume+: triple click the MFB touch button on the left ear.
● Volume -: Three clicks on the MFB touch button on the right ear.
● Previous song: Double-click the MFB touch key on the left ear.
● Next song: Double-click the MFB touch key on the right ear.
● Answer the incoming call: When calling, click the MFB touch button on the
left and right ears.
● Hang up the phone: During the call, double-click the MFB touch button on the
left and right ears.
● Refuse to answer: When calling, press and hold the MFB touch button for 2
seconds at any time.
● Start the voice assistant: press and hold the MFB touch key for about 3
seconds to enter the voice assistant, and click to exit.
● Hall function: When charging the headset, put it into the charging bin, close
the charging bin cover box, and the indicator light for charging the headset
is on, and the blue light is always on. The earphone is full, the box is off,
and the earphone is off.
● Pairing timeout: When the phone is turned on and not connected, it will
automatically turn off after 5 minutes.
● Reset the headset: When the phone is not connected when the phone is
turned on, press the MFB button on the left and right ears to reset the
factory settings of the headset. The white and blue light will turn on for
2 seconds after the reset is successful.
2
4
5
6
1
/