Dell PowerEdge C2100 ユーザーガイド

Dell™ PowerEdge™ C2100

Getting Started

With Your System

系统使用入门

Memulai Pengaktifan dengan Sistem

はじめに

시스템 시작 안내서

Dell PowerEdge C2100

Getting Started

With Your System

Regulatory Model FS12-TY

Notes, Cautions, and Warnings

NOTE:

A NOTE indicates important information that helps you make better use of

your computer.

CAUTION:

A CAUTION indicates potential damage to hardware or loss of data

if instructions are not followed.

WARNING:

A WARNING indicates a potential for property damage, personal

injury, or death.

____________________

Trademarks used in this text: Dell, the DELL logo, and PowerEdge, are trademarks of Dell Inc.;

Citrix and XenServer are trademarks of Citrix Systems, Inc. and/or more of its subsidiaries, and may

be registered in the United States Patent and Trademark Office and in other countries; Intel and Xeon

are registered trademarks of Intel Corporation in the U.S. and other countries; VMware is a registered

trademark of VMware, Inc. in the United States and/or other jurisdictions; Red Hat and Red Hat

Enterprise Linux are registered trademarks of Red Hat, Inc. in the United States and other countries;

SUSE is a registered trademark of Novell, Inc. in the United States and other countries.

Regulatory Model FS12-TY

2013 - 11 P/N 70WC0 Rev. A02

Getting Started With Your System

3

Installation and Configuration

WARNING:

Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Rails and System in a Rack

WARNING:

Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

WARNING:

The system is not fixed to the rack or mounted on the rails. To avoid

personal injury or damage to the system, you must adequately support the system

rack during installation and removal.

CAUTION:

Before installing systems in a rack, install front and side stabilizers

on stand-alone (single) racks or the front stabilizer on racks joined to other racks.

Failure to install stabilizers accordingly before installing systems in a rack could

cause the rack to tip over, potentially resulting in bodily injury under certain

circumstances. Therefore, always install the stabilizer(s) before installing

components in the rack.

CAUTION:

Many repairs may only be done by a certified service technician.

You should only perform troubleshooting and simple repairs as authorized in

your product documentation, or as directed by the online or telephone service

and support team. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow the safety instructions that came

with the product.

4

Getting Started With Your System

1

Secure the rails to the front of the rack using two screws and to the back of

the rack using four screws.

2

Align the keyhole slot on the chassis rails with the corresponding pin

on either side of the system and slide the chassis rails towards the front

of the system until it locks into place. Secure the chassis rails to the

system using screws.

Getting Started With Your System

5

3

Align and insert the ends of the chassis rails into the ends of the rails and

push the system inward until the chassis rails lock into place.

4

Tighten the thumbscrews to secure the ears of system to the rack.

6

Getting Started With Your System

Optional – Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

Connecting the Power Cable(s)

Getting Started With Your System

7

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor. Plug the other end of the

power cables into a grounded electrical outlet or a separate power source such

as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

Turning On the System

Press the power button on the system and the monitor. The power indicators

should light.

Complete the Operating System Setup

To install an operating system, see the installation and configuration

documentation for your operating system. Be sure the operating

system is installed before installing hardware or software not purchased

with the system.

8

Getting Started With Your System

Supported Operating Systems

•Red Hat

®

Enterprise Linux

®

5.4 Standard edition (x64)

• Red Hat Enterprise Linux 5.4 Standard edition (x86)

•SUSE

®

Linux Enterprise Server 11 (x86_64)

• Citrix

®

XenServer™ Enterprise edition 5.

x

• VMware

®

ESX Server Version 4.0, Update 1

NOTE:

For the latest information on supported operating systems,

see dell.com/ossupport.

Other Information You May Need

WARNING:

See the safety and regulatory information that shipped with

your system. Warranty information may be included within this document or

as a separate document.

•The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components. This document is available online at

dell.com/support/manuals

.

• Dell systems management application documentation provides

information about installing and using the systems management software.

This document is available online at

dell.com/support/manuals

.

NOTE:

Always check for updates on dell.com/support/manuals and read

the updates first because they often supersede information in other documents.

Getting Started With Your System

9

NOM Information (Mexico Only)

The following information is provided on the device described in this

document in compliance with the requirements of the official Mexican

standards (NOM):

Technical Specifications

Importer:

Model number: FS12-TY

Supply voltage: 100–240 V CA

Frequency: 50/60 Hz

Current consumption: 9.0–5.0 A

Processor

Processor type One or two Intel

®

Xeon

®

5500 or 5600 series

processors (up to six core processors)

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots

PCIe

Two x8 half-length, full height

Mezzanine slots

PCIe

Two x4 custom slots

Memory

Architecture 800/1066/1333 MHz DDR-3

unbuffered/registered memory modules with

Error Correcting Code (ECC)

Memory module sockets Eighteen 240-pin DIMMs

Memory module capacities 2 GB, 4 GB, 8 GB, or 16 GB

10

Getting Started With Your System

Minimum RAM 12 GB RAM

Maximum RAM 144 GB (dual rank) using 8 GB DIMM

288 GB (quad rank) using 16 GB DIMM

S3 Sleep State

48 GB using 2 GB or 4 GB DIMM

Drive

Hard drives Up to twelve 3.5", hot-swappable SAS/SATA

hard drives

Up to twenty four 2.5", hot-swappable

SAS/SATA hard drives (when available)

(Optional) up to two 2.5", internal SATA/SSD

hard drives (when available)

Connectors

Back

NIC

Two RJ-45 (for integrated 10/100/1000 Mbps

Ethernet)

KVM over IP port

Dedicated Ethernet port for remote

management access

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Video

Video type AST2050 video controller; VGA connector

Video memory 8 MB

Memory (continued)

Getting Started With Your System

11

Power

AC power supply (redundant)

Wattage 750 W

Voltage

100–240 VAC, 50/60 Hz, 9.5–5.0 A

Heat dissipation

2217.8 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over

the entire system ambient operating range,

the inrush current may reach 55 A per power

supply for 10 ms or less.

Batteries

System battery

CR 2032 3.0-V Lithium coin cell

ROMB battery (optional)

3.7-V Lithium ion battery pack

Physical

Height 87.5 cm (3.44")

Width 43.74 cm (17.22")

Depth 72.2 cm (28.42")

Weight (maximum configuration) 28.5 kg (62.8 lb)

Weight (empty) 12 kg (26.5 lb)

Environmental

For additional information about environmental measurements for specific system

configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE:

For altitudes above 2950 ft,

the maximum operating temperature

is derated 1ºF/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with

a maximum temperature gradation

of 20°C per hour

12

Getting Started With Your System

Relative humidity

Operating

8% to 85% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz

Storage

1.54 Grms at 10–250 Hz for 15 mins

Maximum shock

Operating

One shock pulse in the positive z axis

(one pulse on each side of the system)

of 31 G for 2.6 ms in the operational

orientation

Storage

Six consecutively executed shock pulses

in the positive and negative x, y, and z axes

(one pulse on each side of the system)

of 71 G for up to 2 ms

Six consecutively executed shock pulses

in the positive and negative x, y, and z axes

(one pulse on each side of the system) of

27 G fair squared wave pulse with velocity

at 596.9 cm/sec

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

NOTE:

For altitudes above 2950 ft,

the maximum operating temperature

is derated 1ºF/550 ft.

Storage

–16 to 12,000 m (–50 to 35,000 ft)

Airborne Contaminant Level

Class

G2 or lower as defined by ISA-S71.04-1985

Environmental (continued)

Dell PowerEdge C2100

系统使用入门

管制型号 FS12-TY

注、小心和警告

注：

“注”表示可以帮助您更好地使用计算机的重要信息。

小心：

“小心”表示如果不遵循说明，就有可能损坏硬件或导致数据丢失。

警告：

“警告”表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本文中使用的商标： Dell、DELL 徽标、和 PowerEdge 是 Dell Inc. 的商标； Citrix 和 XenServer

是 Citrix Systems, Inc. 和 / 或其一个或多个子公司的商标，并且可能在美国商标局和其他国家

/ 地区进行了注册； Intel 和 Xeon 是 Intel Corporation 在美国和其他国家 / 地区的注册商标；

VMware 是 VMware, Inc. 在美国和 / 或其他辖区的注册商标； Red Hat 和 Red Hat Enterprise

Linux 是 Red Hat, Inc. 在美国和其他国家 / 地区的注册商标； SUSE 是 Novell, Inc. 在美国和其

他国家 / 地区的注册商标。

管制型号 FS12-TY

2013 - 11 P/N 70WC0 Rev. A02

系统使用入门

15

安装和配置

警告：

执行下列步骤之前，请查看系统随附的安全说明。

打开系统包装

打开系统包装并检查各个组件。

在机架中安装滑轨和系统

警告：

如需抬高系统时，请让别人帮您。为避免受伤，请勿尝试独自提起

系统。

警告：

系统未固定到机架上或未安装在导轨上。为避免人身伤害或损坏系

统，在安装和拆卸过程中必须充分支撑系统机架。

小心：

在机架上安装系统之前，对于独立（单个）机架，请先安装正面和

侧面支脚；对于与其它机架合并在一起的机架，请先安装正面支脚。如果在

安装系统之前，没有给机架安装相应的支脚，则在某些情况下，机架可能会

翻倒，导致人员受伤。因此，在机架上安装组件之前，请务必先安装支脚。

小心：

多数维修只能由经认证的维修技术人员进行。您只能根据产品说明

文件中的授权，或者在联机或电话服务和支持小组的指导下，进行故障排除

和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范围之内。请阅

读并遵循产品附带的安全说明。

16

系统使用入门

1 用两颗螺钉将导轨固定到机架正面，用四颗螺钉将导轨固定到机架

背面。

2

将机箱导轨上的锁孔槽分别对准系统两边的相应销，然后将机箱导轨

滑向系统前端，直至其锁入到位。使用螺钉将机箱导轨固定在系统上。

系统使用入门

17

3

将机箱导轨末端对准导轨末端并插入，然后将系统往内推，直至机箱

导轨锁入到位。

4

拧紧指旋螺钉，将系统吊耳固定到机架上。

18

系统使用入门

可选 — 连接键盘、鼠标和显示器

连接键盘、鼠标和显示器（可选）。

系统背面的连接器附有图标，指示要插入每个连接器的电缆。请确保拧紧

显示器电缆连接器上的螺钉（如果有）。

连接电源电缆

将系统电源电缆连接至系统，如果使用显示器，则将显示器电源电缆连接

至显示器。将电源电缆的另一端插入接地的电源插座或单独的电源，如不

间断电源设备 (UPS) 或配电装置 (PDU)。

ページを読み込んでいます...

Dell PowerEdge C2100 ユーザーガイド

関連論文