Philips PT878/14 ユーザーマニュアル

PT927CC

PT927

PT878

PT877

User manual / 用户手册

Question?

有疑问?

Contact Philips

请联系飞利浦

1

PT927CC, PT927, PT878, PT877

ENGLISH 6

简体中文 30

6

Introduction

Congratulations on your purchase and welcome

to Philips! To fully benet from the support that

Philips offers, register your product at

www.philips.com/welcome.

Please read this user manual, as it contains

information about the wonderful features of this

shaver as well as some tips to make shaving easier

and more enjoyable.

General description (Fig. 1)

A Shaver

1 Protection cap

2 Shaving unit

3 Shaving unit release button

4 Trimmer

5 Trimmer release slide

6 Shaver on/off button

7 Shaving head symbol

8 Battery symbol

B Charging stand (PT927 only)

C Adapter

D Jet Clean System (PT927CC only)

1 Locking lever

2 Shaver holder

3 Cleaning chamber release button

4 Jet Clean System on/off button

5 Cleaning symbol and ‘uid low’ symbol

6 Battery symbol

E Jet Clean solution (HQ200) (PT927CC only)

F Cleaning brush

G Storage pouch (PT927CC/PT927 only)

ENGLISH

Important

Read this user manual carefully before you use the

shaver, the Jet Clean System and the charging stand.

Save the user manual for future reference.

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer. Do not cut

off the adapter to replace it with another plug, as

this causes a hazardous situation.

- The shaver and the Jet Clean System (PT927CC)

are not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or

instruction concerning use of these appliances by

a person responsible for their safety.

- Children should be supervised to ensure that they

do not play with the shaver and the Jet Clean

System (PT927CC).

- Always unplug the shaver before you clean it

under the tap.

Caution

- Never immerse the shaver in water.

- Never immerse the Jet Clean System (PT927CC)

or the charging stand (PT927)in water nor rinse it

under the tap.

-

Do not use the shaver in the bath or in the shower.

- Never use water hotter than 80°C to rinse the shaver.

- Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

ENGLISH 7

- The shaver, the Jet Clean System (PT927CC), the

charging stand (PT927) and the other accessories

are not dishwasher-proof.

- Water may leak from the socket at the bottom

of the shaver when you rinse it. This is normal

and not dangerous because all electronics are

enclosed in a sealed power unit inside the shaver.

- Do not use the shaver, Jet Clean System

(PT927CC), adapter, charging stand (PT927) or

any other part if it is damaged, as this may cause

injury. Always replace a damaged adapter, charging

stand or part with one of the original type.

- Use, charge and store the shaver and the Jet

Clean System (PT927CC) at a temperature

between 10°C and 35°C.

-

Always place and use the shaver and the Jet Clean

System (PT927CC) on a surface that is uid-resistant.

- Only use the adapter, charging stand (PT927)

and accessories supplied.

- Always put the protection cap on the shaver to

prevent damage and to avoid dirt accumulation in

the shaving heads.

Jet Clean (PT927CC only)

- Only use the Jet Clean System with the original Jet

Clean solution (HQ200).

- Always place the Jet Clean System on a stable,

level and horizontal surface to prevent leakage.

- The Jet Clean System thoroughly cleans but does

not disinfect your shaver, therefore do not share

the shaver with others.

- If the shaver and the Jet Clean System

are subjected to a major change in temperature,

pressure or humidity, let them acclimatise for

30 minutes before you use them.

ENGLISH8

- Empty the cleaning chamber of the Jet Clean

System and clean the cleaning chamber thoroughly

by rinsing it with hot tap water every 15 days.

- When the Jet Clean System is ready for use,

do not move it to prevent leakage.

Compliance with standards

- The shaver complies with the internationally

approved IEC safety regulations and can be safely

cleaned under the tap.

- The shaver and the Jet Clean System comply

with all standards regarding electromagnetic elds

(EMF). If handled properly and according to the

instructions in this user manual, they are safe to

use based on scientic evidence available today.

General

- The appliance is equipped with an automatic

voltage selector and is suitable for mains voltages

ranging from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe

low voltage of less than 24 volts.

Charging

It takes approx. 1 hour to fully charge the shaver.

When you charge the shaver for the rst time or

after a long period of disuse, let it charge until the

white battery lights up continuously.

A fully charged shaver provides up to 50 (PT878/

PT877) or 60 (PT927CC/PT927) shaving minutes.

The shaving time may be less than 50 (PT878/

PT877) or 60 (PT927CC/PT927) shaving minutes

as a result of your shaving behaviour, your cleaning

habits or your beard type.

ENGLISH 9

Charge indications

Battery low

- When the battery is almost empty (when there

are only 5 or fewer shaving minutes left), the

battery symbol starts to ash orange.

- When you switch off the shaver, the battery

symbol continues to ash orange for a

few seconds.

Quick charging

- When you start charging the empty battery, the

battery symbol ashes white and orange.

Note: When the battery symbol ashes white and

orange towards only white, you can have a quick shave

of three minutes.

Charging

- When the shaver is charging, the battery symbol

ashes white.

Battery fully charged

- When the battery is fully charged, the battery

symbol lights up white continuously.

Note: After approx. 30 minutes, the battery symbol

goes out to save energy.

Charging with the adapter

Do not charge the shaver in a closed pouch.

1 Put the small plug in the shaver.

2 Put the adapter in the wall socket.

, The battery symbol shows the charging status

of the shaver (see section ‘Charge indications’ in

this chapter).

ENGLISH10

Charging in the charging stand (PT927 only)

1 Put the small plug in the charging stand.

2 Put the adapter in the wall socket.

3 Place the shaver in the charging stand.

, The battery symbol shows the charging status

of the shaver (see section ‘Charge indications’ in

this chapter).

Charging in the Jet Clean System

(PT927CC only)

1 Put the small plug in the Jet Clean System.

2 Put the adapter in the wall socket.

3 Place the shaver without protection cap upside

down in the shaver holder.

Note: The shaver cannot be placed in the Jet Clean

System when the protection cap is on the shaving unit.

4 Push down the locking lever completely to lock

the shaver into place.

, The battery symbol on the Jet Clean System

ashes to indicate that the shaver is being

charged.

Note: When the Jet Clean System is performing the

cleaning program, the battery symbol is out.

, When the battery is fully charged, the battery

symbol on the Jet Clean System lights up

continuously.

Note: After approx. 30 minutes, the battery symbol

goes out to save energy.

ENGLISH 11

5 To remove the shaver from the Jet Clean

System, move the locking lever upwards until it

does not go any further and remove the shaver.

Using the shaver

Note: You can also use the appliance directly from the

mains. Simply connect the shaver to the mains.

Shaving

1 Press the on/off button once to switch on the

shaver.

2 Move the shaving heads over your skin. Make

circular movements.

- Your skin may need 2 or 3 weeks to get

accustomed to the Philips shaving system.

3 Press the on/off button once to switch off the

shaver.

4 Clean the shaver (see chapter ‘Cleaning and

maintenance’).

Trimming

You can use the trimmer to groom your sideburns

and moustache.

1 Press the on/off button once to switch on the

shaver.

ENGLISH12

2 Push the trimmer slide downwards to open

the trimmer.

, You can now start trimming.

3 After trimming, close the trimmer and switch

off the shaver.

4 Clean the trimmer (see chapter ‘Cleaning and

Maintenance’).

Cleaning and maintenance

Never use compressed air, scouring pads,

abrasive cleaning agents or aggressive liquids

such as petrol or acetone to clean the shaver, the

charging stand (PT927) and the Jet Clean System

(PT927CC).

- The best and most hygienic way to clean the

shaver is in the Jet Clean System (PT927CC). You

can also rinse the shaver under the tap or clean it

with the cleaning brush supplied.

- Clean the shaver after every shave for optimal

shaving performance.

- Regular cleaning guarantees better shaving

performance.

- For the best cleaning results, we advise you to

use the Philips Cleaning spray (HQ110) and the

Jet Clean solution (HQ200)(PT927CC).

- Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

ENGLISH 13

Note: Water may leak from the socket at the bottom

of the shaver when you rinse it. This is normal and not

dangerous because all electronics are enclosed in a

sealed power unit inside the shaver.

Cleaning the shaving unit under the tap

1 Switch off the shaver and disconnect it from

the mains.

2 Press the release button to open the shaving

unit.

3 Rinse the shaving unit and hair chamber under

a hot tap for 30 seconds.

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

- Rinse the hair chamber and the inside of the

shaving unit.

- Rinse the outside of the shaving unit.

4 Close the shaving unit and shake off excess

water.

Be careful not to hit the shaving unit against

anything while shaking off excess water.

Never dry the shaving unit and the hair chamber

with a towel or tissue, as this may damage the

shaving heads and the coupling spindles.

5 Open the shaving unit again and leave it open

to let the shaver dry completely.

ENGLISH14

Cleaning the shaving unit with the cleaning

brush

1 Switch off the shaver and disconnect it from

the mains.

2 Press the release button to open the shaving

unit.

3 Pull the shaving unit off the shaver.

4 Turn the lock anticlockwise (A) and remove

the retaining frame (B).

5 Remove and clean one shaving head at a time.

Each shaving head consists of a cutter and a

guard.

Note: Do not clean more than one cutter and guard

at a time, since they are all matching sets. If you

accidentally mix up the cutters and guards, it may take

several weeks before optimal shaving performance is

restored.

- Remove the cutter from the shaving guard and

clean it with the brush.

ENGLISH 15

- Clean the inside and outside of the shaving guard

with the brush.

6 Put the shaving heads back into the shaving

unit.

Note: Make sure that the projections of the shaving

heads t exactly into the recesses.

7 Put the retaining frame back into the shaving

unit (A) and turn the lock clockwise (B).

8 Insert the lug of the shaving unit into the slot

in the top of the shaver. Then close the shaving

unit.

Note: If the shaving unit does not close smoothly, check

if you have inserted the shaving heads properly and if

the retaining frame is locked.

ENGLISH16

Cleaning the shaving unit in the Jet Clean

System (PT927CC only)

The Jet Clean System cleans the shaving unit.

Preparing the Jet Clean System for use

Note: Fill the cleaning chamber before rst use and

when the ‘uid low’ symbol ashes to indicate that the

uid level is too low. When the uid level drops below

the minimum level, the cleaning symbol and the ‘uid

low’ symbol start to ash and the shaver holder returns

to its starting position

1 Simultaneously press the release buttons

on both sides of the cleaning chamber (A).

Then lift the Jet Clean System off the cleaning

chamber (B).

, The cleaning chamber remains behind.

2 Unscrew the cap from the bottle with Jet

Clean solution (HQ200) and remove the

airtight seal.

3 Fill the cleaning chamber with Jet Clean

solution (HQ200) up to the MAX indication.

Note: Make sure the cleaning chamber is always lled

above the MIN indication.

4 Place the Jet Clean System back onto the

cleaning chamber (‘click’).

Make sure that the release buttons snap back into

place.

When the cleaning chamber is lled with Jet Clean

solution, do not move it to prevent leakage.

ENGLISH 17

5 Put the small plug in the Jet Clean System and

put the adapter in the wall socket.

, The shaver holder automatically moves to its

highest position.

The Jet Clean System is now ready for use.

Using the Jet Clean System

1 Place the shaver without protection cap upside

down in the shaver holder. Push down the

locking lever completely to lock the shaver

into place.

, The battery symbol on the Jet Clean System

goes on to indicate that the shaver is being

charged.

Note: The shaver cannot be placed in the Jet Clean

System when the protection cap is on the shaving unit.

2 Press the on/off button on the Jet Clean

System to start the cleaning program.

, The battery symbol on the Jet Clean System

goes out.

, During the cleaning program, the cleaning

symbol starts to ash and the shaver is

automatically lowered into the cleaning uid.

, The shaver automatically switches on and off

several times and moves up and down.

, The cleaning symbol ashes throughout the

cleaning program, which takes approx. 8 minutes.

, After the cleaning program, the battery symbol

on the Jet Clean System goes on to indicate that

the shaver is being charged.

ENGLISH18

Note: If you press the on/off button of the Jet

Clean System during the cleaning program, the

program aborts and resets. In this case, the cleaning

stops ashing and the shaver holder returns to its

starting position. The shaver may still be wet and dirty,

because the cleaning program has not been nished.

Note: If you remove the adapter from the wall socket

during the cleaning program, the program aborts. The

shaver holder remains in its current position. When you

put the adapter back into the wall socket, the shaver

holder moves to its highest position.

Note: When the uid level drops below the minimum

level, the cleaning symbol and the ‘uid low’ symbol

start to ash with intervals and the shaver holder

returns to its starting position

Cleaning the Jet Clean System

Empty the cleaning chamber and clean it thoroughly

by rinsing it with hot tap water every 15 days if you

use the Jet Clean System daily. Otherwise empty and

clean the cleaning chamber at least once a month.

1 Clean the outside of the Jet Clean System with

a moist cloth.

Never immerse the Jet Clean System in water, nor

rinse it under the tap.

2 Simultaneously press the release buttons on

both sides of the Jet Clean System (1). Then lift

the Jet Clean System off the cleaning chamber (2).

, The cleaning chamber remains behind.

ENGLISH 19

3 Pour any remaining cleaning uid out of the

cleaning chamber.

You can simply pour the cleaning uid down the sink,

this is not harmful to the environment.

4 Rinse the cleaning chamber under a hot tap.

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

The cleaning chamber is not dishwasher-proof.

5 Fill the cleaning chamber with Jet Clean

solution (HQ200) up to the MAX indication.

Note: Make sure the cleaning chamber is always lled

above the MIN indication.

6 Place the Jet Clean System back onto the

cleaning chamber (‘click’).

Make sure that the release buttons snap back into

place.

Cleaning the trimmer with the cleaning brush

Clean the trimmer every time you have used it.

1 Switch off the shaver and disconnect it from

the mains.

2 Push the trimmer slide downwards to open

the trimmer.

ENGLISH20

ページが読み込まれています...

Philips PT878/14 ユーザーマニュアル

このマニュアルも適しています

Philips PT878/14 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント