Philips HQ6075/16
Philips HQ6075/16 は、快適で肌に優しいシェービングを可能にするコードレス電気シェーバーです。Super Lift & Cut シェービングシステムを採用し、長い毛も短い毛も根元から剃り上げます。また、リチウムイオン電池を搭載し、1時間の充電で最大50分のコードレスシェービングが可能です。
HQ6075/16 は、以下の機能を備えています。
- Super Lift & Cut シェービングシステム：長い毛も短い毛も根元から剃り上げます。
- リチウムイオン電池：1時間の充電で最大50分のコードレスシェービングが可能です。
- 人間工学に基づいたデザイン：手にフィットし、操作しやすい設計です。
- 洗浄が簡単：水洗い可能で、清潔に保つことができます。
HQ6075/1
Philips HQ6075/16
Philips HQ6075/16 は、快適で肌に優しいシェービングを可能にするコードレス電気シェーバーです。Super Lift & Cut シェービングシステムを採用し、長い毛も短い毛も根元から剃り上げます。また、リチウムイオン電池を搭載し、1時間の充電で最大50分のコードレスシェービングが可能です。
HQ6075/16 は、以下の機能を備えています。
- Super Lift & Cut シェービングシステム：長い毛も短い毛も根元から剃り上げます。
- リチウムイオン電池：1時間の充電で最大50分のコードレスシェービングが可能です。
- 人間工学に基づいたデザイン：手にフィットし、操作しやすい設計です。
- 洗浄が簡単：水洗い可能で、清潔に保つことができます。
HQ6075/1
HQ6075, HQ6073, HQ6070
1
2
3
4
5 6
7 8
9
10
11 12
13
14
15
16
17 18
19
ENGLISH
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Only use the powerplug supplied.
The powerplug transforms 100-240 volts to a safe
low voltage of less than 24 volts.
The powerplug contains a transformer. Do not cut
off the powerplug to replace it with another plug, as
this causes a hazardous situation.
Do not use a damaged powerplug.
If the powerplug is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
Charge and store the shaver at a temperature
between 5°C and 35°C.
Do not recharge the shaver in a closed pouch.
Make sure the powerplug does not get wet.
Always unplug the shaver before cleaning it under
the tap.
The appliance complies with the internationally
approved IEC safety regulations and can be safely
cleaned under the tap (Fig. 1).
Be careful with hot water. Always check if the water is not
too hot, to prevent your hands from getting burnt.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this user
manual, the appliance is safe to use based on scientic
evidence available today.
Charging
Make sure the appliance is switched off before you start
to charge it.
To prevent the battery from going at during shaving, you
can also charge the shaver in between shaves, even if the
battery is not completely empty yet. This will not damage
the battery.
Charging normally takes approx. 8 hours.
Do not leave the appliance connected to the mains for
more than 24 hours.
Charge indications
Charging
When you start charging the empty shaver the
battery symbol lights up (Fig. 2).
Battery running low
HQ6075/HQ6073: When the battery is running low,
the red battery symbol starts burning. When you
switch off the shaver, the red battery symbol starts
to ash. (Fig. 2)
HQ6070: There is no warning or indication that the
battery is running low. The appliance switches off
automatically when the battery is completely empty.
Charging the appliance
Charge the appliance when the red battery symbol burns
or ashes (HQ6075/HQ6073) or when the motor stops
or starts running slower (HQ6070).
1 Put the appliance plug in the shaver (Fig. 3).
2 Put the powerplug in the wall socket.
3 Remove the powerplug from the wall socket and
pull the appliance plug out of the shaver when the
battery has been fully charged.
Cordless shaving time
A fully charged shaver has a cordless shaving time of up
to 40 minutes.
Using the appliance
Shaving
1 Press the on/off button once to switch on the
shaver.
-
-
-
-
-
-
-
-
-
-
-
-
,
,
,
The light ring goes on.
2 Move the shaving heads quickly over your skin,
making both straight and circular
movements (Fig. 4).
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get accustomed to
the Philips shaving system.
3 Press the on/off button once to switch on the
shaver.
4 Put the protection cap on the shaver every time
you have used it, to prevent damage (Fig. 5).
Trimming
For grooming sideburns and moustache.
1 Open the trimmer by pushing the slide
upwards (Fig. 6).
The trimmer can be activated while the motor is running.
Cleaning and maintenance
Regular cleaning guarantees better shaving performance.
The easiest and most hygienic way to clean the appliance
is to rinse the shaving unit and the hair chamber with hot
water every time you have used the appliance.
Be careful with hot water. Always check if the water is
not too hot, to prevent your hands from getting burnt.
Every day: shaving unit and hair chamber
1 Switch off the shaver, remove the powerplug from
the wall socket and pull the appliance plug out of
the shaver.
2 Press the release button (1) and open the shaving
unit (2) (Fig. 7).
3 Clean the shaving unit and the hair chamber by
rinsing them under a hot tap for some time (Fig. 8).
Make sure the inside of the shaving unit and the hair
chamber have been cleaned properly.
4 Rinse the outside of the appliance (Fig. 9).
5 Close the shaving unit and shake off excess water.
Never dry the shaving unit with a towel or tissue, as
this may damage the shaving heads.
6 Open the shaving unit again and leave it open to let
the appliance dry completely (Fig. 10).
You can also clean the hair chamber without water by
using the brush supplied.
Every six months: shaving heads
1 Open the shaving unit and pull it off the shaver.
You can also leave the shaving unit attached to the shaver.
2 HQ6075: Remove the retaining frame (Fig. 11).
3 HQ6073/HQ6070: Open the shaving unit, turn the
wheel anticlockwise (1) and remove the retaining
frame (2) (Fig. 12).
4 Clean the cutters and guards with the brush
supplied (your shaving heads may differ from the
one shown in the gure) (Fig. 13).
Do not clean more than one cutter and guard at a time,
since they are all matching sets. If you accidentally mix up
the cutters and guards, it may take several weeks before
optimal shaving performance is restored.
5 HQ6075: Put the shaving heads back into the
shaving unit and then put the retaining frame back
into the shaving unit (Fig. 14).
Make sure that the projections of the shaving heads t
into the recesses.
6 HQ6073/HQ6070: Put the shaving heads back into
the shaving unit. Put the retaining frame back into
the shaving unit and turn the lock clockwise (your
shaving heads may differ from the one shown in the
gure).
7 Put the shaving unit back onto the shaver by
inserting the hinge into the slot in the rim of the
hair chamber and pushing it home until it locks into
place (‘click’). (Fig. 15)
8 Close the shaving unit.
Trimmer
Clean the trimmer every time you have used it.
1 Switch off the shaver, remove the powerplug from
the wall socket and pull the appliance plug out of
the shaver.
2 Clean the trimmer with the brush supplied (Fig. 16).
3 Lubricate the trimmer teeth with a drop of sewing
machine oil every six months (Fig. 17).
Storage
Put the protection cap on the shaver to prevent
damage (Fig. 5).
HQ6075/HQ6073: Store the appliance in the pouch.
Replacement
Replace the shaving heads every two years for optimal
shaving results.
Replace damaged or worn shaving heads with HQ64
Super Lift & Cut Shaving Heads (HQ6073/HQ6070) or
HQ8 Precise Cutting System Shaving Heads (HQ6075).
1 Switch off the shaver, remove the powerplug from
the wall socket and pull the appliance plug out of
the shaver.
2 Open the shaving unit and pull it off the shaver.
You can also leave the shaving unit attached to the shaver.
3 HQ6075: Remove the retaining frame (Fig. 11).
4 HQ6073/HQ6070: Open the shaving unit, turn the
wheel anticlockwise (1) and remove the retaining
frame (2). (Fig. 12)
5 Remove the shaving heads and place new ones in
the shaving unit. (Fig. 14)
6 HQ6075: Put the shaving heads back into the
shaving unit and then put the retaining frame back
into the shaving unit.
Make sure that the projections of the shaving heads t
into the recesses.
7 HQ6073/HQ6070: Put the shaving heads back into
the shaving unit. Put the retaining frame back into
the shaving unit and turn the lock clockwise (your
shaving heads may differ from the one shown in the
gure).
8 Put the shaving unit back onto the shaver by
inserting the hinge into the slot in the rim of the
hair chamber and pushing it home until it locks into
place (‘click’) (Fig. 15).
9 Close the shaving unit.
Accessories
The following accessories are available:
HQ8500/HQ8000 powerplug
HQ64 Super Lift & Cut Shaving Heads (HQ6073/
HQ6070)
HQ8 Precise Cutting System Shaving Heads
(HQ6075)
HQ110 Philips Shaving Head Cleaning Spray (not
available in China)
Environment
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an ofcial collection point for recycling. By doing
this, you help to preserve the environment (Fig. 18).
The built-in rechargeable shaver battery contains
substances that may pollute the environment. Always
remove the battery before you discard and hand in
the shaver at an ofcial collection point. Dispose of
the battery at an ofcial collection point for batteries.
If you have trouble removing the battery, you can
also take the shaver to a Philips service centre. The
staff of this centre will remove the battery for you
and will dispose of it in an environmentally safe way.
Disposal of the battery
Only remove the battery if it is completely empty.
1 Remove the powerplug from the wall socket and
pull the appliance plug out of the shaver.
2 Let the shaver run until it stops, undo the screws
and open the shaver (Fig. 19).
3 Remove the battery.
Do not connect the shaver to the mains again after the
battery has been removed.
,
,
-
-
-
-
-
-
4222.002.5092.1
2/5
Guarantee & service
If you need information or if you have a problem, please
visit the Philips website at www.philips.com or contact the
Philips Customer Care Centre in your country (you nd
its phone number in the worldwide guarantee leaet). If
there is no Customer Care Centre in your country, go to
your local Philips dealer or contact the Service
Department of Philips Domestic Appliances and Personal
Care BV.
Guarantee restrictions
The shaving heads (cutters and guards) are not covered
by the terms of the international guarantee because they
are subject to wear.
Frequently asked questions
Question Answer
Why doesn’t
the shaver
shave as well
as it used to?
You may not have cleaned the
appliance properly. Clean the shaving
heads thoroughly (see chapter
‘Cleaning and maintenance’).
Long hairs may be obstructing the
shaving heads. Clean the cutters and
guards properly with the brush
supplied (see chapter ‘Cleaning and
maintenance’).
The shaving heads may be damaged
or worn. Replace the shaving heads
(see chapter ‘Replacement’).
Why doesn’t
the shaver
switch on
when I press
the on/off
button?
The battery may be empty. Recharge
the battery (see chapter ‘Charging’).
The shaving
unit has come
off the shaver.
What should I
do?
Simply reattach the shaving unit by
pressing it onto the shaver (see
chapter ‘Replacement’, item 5).
4222.002.5092.1
3/5
简体中文
注意事项
使用产品之前，请仔细阅读本使用
说明书，并妥善保管以备日后参
考。
本产品不打算由肢体不健全、感
觉或精神上有障碍或缺乏相关经
验和知识的人（包括儿童）使
用，除非有负责他们安全的人对
他们使用本产品进行监督或指
导。
应照看好儿童，确保他们不玩耍
这些产品。
只能使用产品随附的电源插头。
电源插头可将 100-240 伏的电
压转换为 24 伏以下的安全低电
压。
电源插头中含有一个变压器。切
勿将其剪断，而用另一个插头代
替，否则将导致严重后果。
不要使用已经损坏的电源插头。
电源软线不能更换，如果软线损
坏，此器具（电源适配器）应废
弃。如果电源插头已损坏，则必
须用原装型号替换，以免发生危
险。
必须在 5 摄氏度至 35 摄氏度之
间的温度下充电和存放剃须刀。
不要将剃须刀放在软袋里充电。
确保电源插头干燥。
在自来水龙头下清洗剃须刀之
前，务必拔掉其电源插头。
此产品符合国际认可的 IEC 安
全标准，可放心在自来水龙头下
清洗。 (图 1)
使用热水时一定要小心。切记先检
查水温是否太高，以防烫手。
电磁场 (EMF)
这款飞利浦产品符合关于电磁场 (EMF) 的所有相关
标准。据目前的科学证明，如果正确使用并按照本
用户手册中的说明进行操作，本产品是安全的。
充电
开始充电之前确保产品电源已关闭。
要防止电池在剃须时耗尽，您还可以在两次剃须之
间为剃须刀充电，即使电量没有完全耗尽。这不会
对电池造成损害。
一般充电时间大约为 8 小时。
不要将本产品与电源接通超过 24
小时。
充电指示
充电
开始充电时，电池符号指示灯亮起。 (图 2)
电池电量不足
HQ6075/HQ6073：当电池电量不足时，红色电
池指示灯开始亮起。当关闭剃须刀时，红色电池
指示灯开始闪烁。 (图 2)
HQ6070：当电池处于低电量状态时没有警报或
提示。电池完全耗尽时产品将自动切断电源。
-
-
-
-
-
-
-
-
-
-
-
-
,
,
,
为产品充电
当红色电池指示灯亮起或闪烁 (HQ6075/HQ6073)
或当马达停转或转速开始下降 (HQ6070) 时，应为
产品充电。
1 将产品插头插入剃须刀。 (图 3)
2 将电源插头插入壁装插座。
3 电池充满后，从壁装式插座中拔下电源插头，并
从剃须刀上拔下产品插头。
不接电源的剃须时间
完全充电的剃须刀在不连接电源的情况下最长可使
用达 40 分钟。
使用本产品
剃毛
1 按一下开/关按钮打开剃须刀。
光环亮起。
2 将剃须刀头在皮肤上快速移动，作直线和迂回动
作。 (图 4)
在干爽的面部剃须效果最佳。
您的皮肤可能需要 2 到 3 周才能适应飞利浦剃须系
统。
3 按一下开/关按钮打开剃须刀。
4 每次使用后，盖上剃须刀保护盖，以防受
损。 (图 5)
修剪
用于修剪鬓角和小胡子。
1 向上推动滑块来打开修发器。 (图 6)
当马达运转时，修发器便可以启动。
清洁和维护
为保证更好的剃须效果，剃须刀必须定期清洗。
最简单和最卫生的清洁方法是每次使用完本产品之
后，用热水冲洗剃须刀头部件和胡茬储藏室。
使用热水时一定要小心。切记先检
查水温是否太高，以防烫手。
每天：剃须刀头部件和胡茬储
藏室
1 关闭剃须刀电源，从壁装式电源插座中拔下电源
插头，并从剃须刀上拔下产品插头。
2 按下释放钮 (1) ，打开剃须刀头部件
(2)。 (图 7)
3 在热水龙头下，冲洗剃须刀头部件和胡茬储藏室
一段时间。 (图 8)
确保剃须刀头部件和胡茬储藏室的内部已彻底清
洁。
4 冲洗产品表面。 (图 9)
5 关闭剃须刀头部件并甩掉多余的水份。
不要用毛巾或纸巾擦拭剃须刀头部
件，因为这样可能会损坏剃须刀
头。
6 再次打开剃须刀头部件，使它保持打开状态，让
产品完全晾干。 (图 10)
除了冲洗方式外，您还可以使用随附的刷子清洁胡
茬储藏室。
每 6 个月：剃须刀头
1 打开剃须刀头部件并将它从剃须刀上拔下。
您还可以让剃须刀头部件继续留在剃须刀上。
2 HQ6075：取下固定架。 (图 11)
3 HQ6073/HQ6070：打开剃须刀头部件，逆时针
方向转动轮轴 (1) 并取下固定架 (2)。 (图 12)
4 用随附的刷子清洁刀片和网罩（剃须刀头可能与
图中显示的刀头不同）。 (图 13)
不要同时清洁多组刀片和网罩，因为它们都是相互
匹配的。如果不小心将刀片和网罩弄混，则需要数
周时间才能恢复产品的最佳剃须性能。
5 HQ6075：将剃须刀头放回剃须刀头部件，然后
将固定架放回剃须刀头部件。 (图 14)
确保剃须刀头凸起部位正好插入凹陷部位。
6 HQ6073/HQ6070：将剃须刀头重新安装到剃须
刀头部件上。将固定架装回剃须刀头部件，顺时
针转动并锁住（剃须刀头可能与图中显示的刀头
不同）。
7 将剃须刀头部件装回剃须刀。方法是将铰链插入
胡茬储藏室边的槽中，将其推到位，直到锁定到
位（可听到“咔嗒”声）。 (图 15)
8 关闭剃须刀头部件。
修发器
每次使用后都要清洁修发器。
1 关闭剃须刀电源，从壁装式电源插座中拔下电源
插头，并从剃须刀上拔下产品插头。
2 用随附的刷子清洁修发器。 (图 16)
3 每六个月用一滴缝纫机油润滑修发器
齿。 (图 17)
存放
盖上剃须刀保护盖，以防受损。 (图 5)
HQ6075/HQ6073：将产品存放在软袋中。
更换
每两年更换一次刀头以获得最佳的剃须效果。
使用 HQ64 飞利浦剃须刀头 (HQ6073/HQ6070) 或
HQ8 飞利浦剃须刀头 (HQ6075) 替换损坏或磨损的
剃须刀头。
1 关闭剃须刀电源，从壁装式电源插座中拔下电源
插头，并从剃须刀上拔下产品插头。
2 打开剃须刀头部件并将它从剃须刀上拔下。
您还可以让剃须刀头部件继续留在剃须刀上。
3 HQ6075：取下固定架。 (图 11)
4 HQ6073/HQ6070：打开剃须刀头部件，逆时针
方向转动轮轴 (1) 并取下固定架 (2)。 (图 12)
5 取下剃须刀头，在剃须刀头部件上装上新刀
头。 (图 14)
6 HQ6075：将剃须刀头放回剃须刀头部件，然后
将固定架放回剃须刀头部件。
确保剃须刀头凸起部位正好插入凹陷部位。
7 HQ6073/HQ6070：将剃须刀头重新安装到剃须
刀头部件上。将固定架装回剃须刀头部件，顺时
针转动并锁住（剃须刀头可能与图中显示的刀头
不同）。
8 将剃须刀头部件装回剃须刀。方法是将铰链插入
胡茬储藏室边的槽中，将其推到位，直到锁定到
位（可听到“咔嗒”声）。 (图 15)
9 关闭剃须刀头部件。
附件
可选配以下附件：
HQ8500/HQ8000 电源插头
HQ64 飞利浦剃须刀头 (HQ6073/HQ6070)
HQ8 飞利浦剃须刀头 (HQ6075)
环保
弃置产品时，请不要将其与一般生活垃圾堆放在
一起；应将其交给官方指定的回收中心。这样做
有利于环保。 (图 18)
内置充电电池含有可能会污染环境的物质。丢弃
剃须刀时，一定要将电池取出，并将剃须刀送到
官方指定的回收站。到官方指定的电池回收站处
理电池。如果您在取出电池时遇到问题，您也可
以将剃须刀送至飞利浦维修中心。维修中心的员
工会帮您取出电池，并以环保的方式处理它。
处理电池
仅在电池电量完全耗尽后方可取出
电池。
1 从壁装式插座中拔下电源插头，并从剃须刀上拔
下产品插头。
2 让剃须刀运转直到停止，拧下螺钉并打开剃须
刀。 (图 19)
3 取出电池。
取出电池后，不要再将剃须刀与电
源连接在一起。
,
,
-
-
-
-
-
4222.002.5092.1
4/5
保修与服务
如果您需要详细信息或有任何问题，请浏览飞利浦
网站，地址为
www.philips.com。您也可以与本国的飞利浦顾客服
务中心联系（您可以从全球保修卡中找到电话号
码）。如果本国没有飞利浦顾客服务中心，请与当
地的飞利浦经销商或与飞利浦家庭小电器的维修中
心联系。
保修限制
由于剃须刀头（刀片和网罩）属于易磨损物品，因
此不在国际保修条款的涵盖范围之列。
常见问题
问题 回答
为什么剃须刀
的剃须效果没
有以前好？
您可能没有正确清洁本产品。请
彻底清洁剃须刀头（见“清洁和
保养”一章）。
过长的胡须可能堵塞了剃须刀
头。请使用随附的刷子正确清洁
刀片和网罩（见“清洁和保
养”一章）。
剃须刀头可能已损坏或磨损。请
更换剃须刀头（见“更换”一
章）。
按下开/关钮
时，为什么无
法打开剃须
刀？
电池可能没电。为电池充电（
见“充电”一章）。
剃须刀头部件
从剃须刀上脱
落。该怎样处
理？
只需重新安装剃须刀头部件，将
其按到剃须刀上（见“更换”一
章，第 5 节）。
2008/07/09
HQ6075,
HQ6073, HQ6070
4222.002.5092.1
5/5
-
1
-
2
-
3
-
4
-
5
Philips HQ6075/16
Philips HQ6075/16 は、快適で肌に優しいシェービングを可能にするコードレス電気シェーバーです。Super Lift & Cut シェービングシステムを採用し、長い毛も短い毛も根元から剃り上げます。また、リチウムイオン電池を搭載し、1時間の充電で最大50分のコードレスシェービングが可能です。
HQ6075/16 は、以下の機能を備えています。
- Super Lift & Cut シェービングシステム：長い毛も短い毛も根元から剃り上げます。
- リチウムイオン電池：1時間の充電で最大50分のコードレスシェービングが可能です。
- 人間工学に基づいたデザイン：手にフィットし、操作しやすい設計です。
- 洗浄が簡単：水洗い可能で、清潔に保つことができます。
HQ6075/1
他の言語で
- English: Philips HQ6075/16 User manual
関連論文
-
Philips HQ6095/22 ユーザーマニュアル
-
Philips HQ6075/16 Product Datasheet
-
-
-
-
-
-
-
-